Abstract: New advancement of technology and never satisfying demands of the civilization are putting huge pressure on the natural fuel resources and these resources are at a constant threat to its sustainability. To get the best out of the automobile, the optimum balance between performance and fuel economy is important. In the present state of art, either of the above two aspects are taken into mind while designing and development process which puts the other in the loss as increase in fuel economy leads to decrement in performance and vice-versa. In-depth observation of the vehicle dynamics apparently shows that large amount of energy is lost during braking and likewise large amount of fuel is consumed to reclaim the initial state, this leads to lower fuel efficiency to gain the same performance. Current use of Kinetic Energy Recovery System is only limited to sports vehicles only because of the higher cost of this system. They are also temporary in nature as power can be squeezed only during a small time duration and use of superior parts leads to high cost, which results on concentration on performance only and neglecting the fuel economy. In this paper Kinetic Energy Recovery System for storing the power and then using the same while accelerating has been discussed. The major storing element in this system is a Flat Spiral Spring that will store energy by compression and torsion.
The use of spring ensure the permanent storage of energy until used by the driver unlike present mechanical regeneration system in which the energy stored decreases with time and is eventually lost. A combination of internal gears and spur gears will be used in order to make the energy release uniform which will lead to safe usage. The system can be used to improve the fuel efficiency by assisting in overcoming the vehicle’s inertia after braking or to provide instant acceleration whenever required by the driver. The performance characteristics of the system including response time, mechanical efficiency and overall increase in efficiency are demonstrated. This technology makes the KERS (Kinetic Energy Recovery System) more flexible and economical allowing specific application while at the same time increasing the time frame and ease of usage.
Abstract: Curing of paints by exposure to UV radiations is
emerging as one of the best film forming technique as an alternative
to traditional solvent borne oxidative and thermal curing coatings.
The composition and chemistry of UV curable coatings and role of
multifunctional and monofunctional monomers, oligomers, and
photoinitiators have been discussed. The limitations imposed by
thermodynamic equilibrium and tendency for acrylic double bond
polymerizations during synthesis of multifunctional acrylates have
been presented. Aim of present investigation was thus to explore the
reaction variables associated with synthesis of multifunctional
acrylates. Zirconium oxychloride was evaluated as catalyst against
regular acid functional catalyst. The catalyzed synthesis of glyceryl
acrylate and neopentyl glycol acrylate was conducted by variation of
following reaction parameters: two different reactant molar ratios-
1:4 and 1:6; catalyst usage in % by moles on polyol- 2.5, 5.0 and 7.5
and two different reaction temperatures- 45 and 75 0C. The reaction
was monitored by determination of acid value and hydroxy value at
regular intervals, besides TLC, HPLC, and FTIR analysis of
intermediates and products. On the basis of determination of reaction
progress over 1-60 hrs, the esterification reaction was observed to
follow 2nd order kinetics with rate constant varying from 1*10-4 to
7*10-4. The thermal and catalytic components of second order rate
constant and energy of activation were also determined. Uses of
these kinetic and thermodynamic parameters in design of reactor for
manufacture of multifunctional acrylate ester have been presented.
The synthesized multifunctional acrylates were used to formulate and
apply UV curable clear coat followed by determination of curing
characteristics and mechanical properties of cured film. The overall
curing rates less than 05 min. were easily attained indicating
economical viability of radiation curable system due to faster
production schedules
Abstract: The conjugate gradient optimization algorithm is combined with the modified back propagation algorithm to yield a computationally efficient algorithm for training multilayer perceptron (MLP) networks (CGFR/AG). The computational efficiency is enhanced by adaptively modifying initial search direction as described in the following steps: (1) Modification on standard back propagation algorithm by introducing a gain variation term in the activation function, (2) Calculation of the gradient descent of error with respect to the weights and gains values and (3) the determination of a new search direction by using information calculated in step (2). The performance of the proposed method is demonstrated by comparing accuracy and computation time with the conjugate gradient algorithm used in MATLAB neural network toolbox. The results show that the computational efficiency of the proposed method was better than the standard conjugate gradient algorithm.
Abstract: This research seeks to investigate the frequency and
profitability of index arbitrage opportunities involving the SET50
futures, SET50 component stocks, and the ThaiDEX SET50 ETF
(ticker symbol: TDEX). In particular, the frequency and profit of
arbitrage are measured in the following three arbitrage tests: (1)
SET50 futures vs. ThaiDEX SET50 ETF, (2) SET50 futures vs.
SET50 component stocks, and (3) ThaiDEX SET50 ETF vs. SET50
component stocks are investigated. For tests (2) and (3), the problems
involve conic optimization and quadratic programming as subproblems.
This research is first to apply conic optimization and
quadratic programming techniques in the context of index arbitrage
and is first to investigate such index arbitrage in the Thai equity and
derivatives markets. Thus, the contribution of this study is twofold.
First, its results would help understand the contribution of the
derivatives securities to the efficiency of the Thai markets. Second,
the methodology employed in this study can be applied to other
geographical markets, with minor adjustments.
Abstract: In this paper we present an energy efficient match-line
(ML) sensing scheme for high-speed ternary content-addressable
memory (TCAM). The proposed scheme isolates the sensing unit of
the sense amplifier from the large and variable ML capacitance. It
employs feedback in the sense amplifier to successfully detect a
match while keeping the ML voltage swing low. This reduced voltage
swing results in large energy saving. Simulation performed using
130nm 1.2V CMOS logic shows at least 30% total energy saving in
our scheme compared to popular current race (CR) scheme for
similar search speed. In terms of speed, dynamic energy, peak power
consumption and transistor count our scheme also shows better
performance than mismatch-dependant (MD) power allocation
technique which also employs feedback in the sense amplifier.
Additionally, the implementation of our scheme is simpler than CR
or MD scheme because of absence of analog control voltage and
programmable delay circuit as have been used in those schemes.
Abstract: Electricity market activities and a growing demand for electricity have led to heavily stressed power systems. This requires operation of the networks closer to their stability limits. Power system operation is affected by stability related problems, leading to unpredictable system behavior. Voltage stability refers to the ability of a power system to sustain appropriate voltage levels through large and small disturbances. Steady-state voltage stability is concerned with limits on the existence of steady-state operating points for the network. FACTS devices can be utilized to increase the transmission capacity, the stability margin and dynamic behavior or serve to ensure improved power quality. Their main capabilities are reactive power compensation, voltage control and power flow control. Among the FACTS controllers, Static Var Compensator (SVC) provides fast acting dynamic reactive compensation for voltage support during contingency events. In this paper, voltage stability assessment with appropriate representations of tap-changer transformers and SVC is investigated. Integrating both of these devices is the main topic of this paper. Effect of the presence of tap-changing transformers on static VAR compensator controller parameters and ratings necessary to stabilize load voltages at certain values are highlighted. The interrelation between transformer off nominal tap ratios and the SVC controller gains and droop slopes and the SVC rating are found. P-V curves are constructed to calculate loadability margins.
Abstract: The use of a Geographic Information System (GIS) in
roadway lighting to show the state of street-lighting and nighttime
accident is demonstrated. Geographical maps were generated
showing colored streets based on how much of the street's length is
illuminated. The night to daytime accidents ratio at intersections
were found along with the state of lighting at those intersections.
The result is a method to show the state of street-lighting at roads and
intersections and a quick guide for decision makers to implement
strategies for better street-lighting to reduce night time traffic
accidents in a particular district.
Abstract: Compaction testing methods allow at-speed detecting
of errors while possessing low cost of implementation. Owing to this
distinctive feature, compaction methods have been widely used for
built-in testing, as well as external testing. In the latter case, the
bandwidth requirements to the automated test equipment employed
are relaxed which reduces the overall cost of testing. Concurrent
compaction testing methods use operational signals to detect
misbehavior of the device under test and do not require input test
stimuli. These methods have been employed for digital systems only.
In the present work, we extend the use of compaction methods for
concurrent testing of analog-to-digital converters. We estimate
tolerance bounds for the result of compaction and evaluate the
aliasing rate.
Abstract: A new automatic system for the recognition and re¬construction of resealed and/or rotated partially occluded objects is presented. The objects to be recognized are described by 2D views and each view is occluded by several half-planes. The whole object views and their visible parts (linear cuts) are then stored in a database. To establish if a region R of an input image represents an object possibly occluded, the system generates a set of linear cuts of R and compare them with the elements in the database. Each linear cut of R is associated to the most similar database linear cut. R is recognized as an instance of the object 0 if the majority of the linear cuts of R are associated to a linear cut of views of 0. In the case of recognition, the system reconstructs the occluded part of R and determines the scale factor and the orientation in the image plane of the recognized object view. The system has been tested on two different datasets of objects, showing good performance both in terms of recognition and reconstruction accuracy.
Abstract: Porcine production in China represents approximately
the 50% of the worldwide pig production. Information about pig
husbandry characteristics in China and manure properties from sows
to fatteners in intensive pig farms are not broadly available for
scientific studies as it is a time consuming, expensive task and highly
inaccessible. This study provides a report about solid pig manures
(28% dry matter) in a commercial pig farm located in the peri-urban
area of Beijing as well as a general overview of the current pig
husbandry techniques including pig breeds, feeds, diseases, housing as
well as pig manure and wastewater disposal. The main results are
intended to serve as a literature source for young scientists in order to
understand the main composition of pig manures as well as to identify
the husbandry techniques applied in an intensive pig farm in Beijing.
Abstract: Quaternary InxAlyGa1-x-yN semiconductors have
attracted much research interest because the use of this quaternary
offer the great flexibility in tailoring their band gap profile while
maintaining their lattice-matching and structural integrity. The
structural and optical properties of InxAlyGa1-x-yN alloys grown by
molecular beam epitaxy (MBE) is presented. The structural quality of
InxAlyGa1-x-yN layers was characterized using high-resolution X-ray
diffraction (HRXRD). The results confirm that the InxAlyGa1-x-yN
films had wurtzite structure and without phase separation. As the In
composition increases, the Bragg angle of the (0002) InxAlyGa1-x-yN
peak gradually decreases, indicating the increase in the lattice constant
c of the alloys. FWHM of (0002) InxAlyGa1-x-yN decreases with
increasing In composition from 0 to 0.04, that could indicate the
decrease of quality of the samples due to point defects leading to
non-uniformity of the epilayers. UV-VIS spectroscopy have been used
to study the energy band gap of InxAlyGa1-x-yN. As the indium (In)
compositions increases, the energy band gap decreases. However, for
InxAlyGa1-x-yN with In composition of 0.1, the band gap shows a
sudden increase in energy. This is probably due to local alloy
compositional fluctuations in the epilayer. The bowing parameter
which appears also to be very sensitive on In content is investigated
and obtained b = 50.08 for quaternary InxAlyGa1-x-yN alloys. From
photoluminescence (PL) measurement, green luminescence (GL)
appears at PL spectrum of InxAlyGa1-x-yN, emitted for all x at ~530 nm
and it become more pronounced as the In composition (x) increased,
which is believed cause by gallium vacancies and related to isolated
native defects.
Abstract: Operational safety of critical systems, such as nuclear power plants, industrial chemical processes and means of transportation, is a major concern for system engineers and operators. A means to assure that is on-line safety monitors that deliver three safety tasks; fault detection and diagnosis, alarm annunciation and fault controlling. While current monitors deliver these tasks, benefits and limitations in their approaches have at the same time been highlighted. Drawing from those benefits, this paper develops a distributed monitor based on semi-independent agents, i.e. a multiagent system, and monitoring knowledge derived from a safety assessment model of the monitored system. Agents are deployed hierarchically and provided with knowledge portions and collaboration protocols to reason and integrate over the operational conditions of the components of the monitored system. The monitor aims to address limitations arising from the large-scale, complicated behaviour and distributed nature of monitored systems and deliver the aforementioned three monitoring tasks effectively.
Abstract: Flexible manufacturing system is a system that is able to respond to changed conditions. In general, this flexibility is divided into two key categories and several subcategories. The first category is the so called machine flexibility which enables to make various products by the given machinery. The second category is routing flexibility enabling to execute the same operation by various machines. Flexible manufacturing systems usually consist of three main parts: CNC machine tools, transport system and control system. A higher level of flexible manufacturing systems is represented by the so called intelligent manufacturing systems.
Abstract: Today, incorrect use of lands and land use changes,
excessive grazing, no suitable using of agricultural farms, plowing on
steep slopes, road construct, building construct, mine excavation etc
have been caused increasing of soil erosion and sediment yield. For
erosion and sediment estimation one can use statistical and empirical
methods. This needs to identify land unit map and the map of
effective factors. However, these empirical methods are usually time
consuming and do not give accurate estimation of erosion. In this
study, we applied GIS techniques to estimate erosion and sediment of
Menderjan watershed at upstream Zayandehrud river in center of
Iran. Erosion faces at each land unit were defined on the basis of land
use, geology and land unit map using GIS. The UTM coordinates of
each erosion type that showed more erosion amounts such as rills and
gullies were inserted in GIS using GPS data. The frequency of
erosion indicators at each land unit, land use and their sediment yield
of these indices were calculated. Also using tendency analysis of
sediment yield changes in watershed outlet (Menderjan hydrometric
gauge station), was calculated related parameters and estimation
errors. The results of this study according to implemented watershed
management projects can be used for more rapid and more accurate
estimation of erosion than traditional methods. These results can also
be used for regional erosion assessment and can be used for remote
sensing image processing.
Abstract: The iris recognition technology is the most accurate,
fast and less invasive one compared to other biometric techniques
using for example fingerprints, face, retina, hand geometry, voice or
signature patterns. The system developed in this study has the
potential to play a key role in areas of high-risk security and can
enable organizations with means allowing only to the authorized
personnel a fast and secure way to gain access to such areas. The
paper aim is to perform the iris region detection and iris inner and
outer boundaries localization. The system was implemented on
windows platform using Visual C# programming language. It is easy
and efficient tool for image processing to get great performance
accuracy. In particular, the system includes two main parts. The first
is to preprocess the iris images by using Canny edge detection
methods, segments the iris region from the rest of the image and
determine the location of the iris boundaries by applying Hough
transform. The proposed system tested on 756 iris images from 60
eyes of CASIA iris database images.
Abstract: Manufacturing tolerancing is intended to determine
the intermediate geometrical and dimensional states of the part
during its manufacturing process. These manufacturing dimensions
also serve to satisfy not only the functional requirements given in
the definition drawing, but also the manufacturing constraints, for
example geometrical defects of the machine, vibration and the
wear of the cutting tool. In this paper, an experimental study on the
influence of the wear of the cutting tool (systematic dispersions) is
explored. This study was carried out on three stages .The first stage
allows machining without elimination of dispersions (random,
systematic) so the tolerances of manufacture according to total
dispersions. In the second stage, the results of the first stage are
filtered in such way to obtain the tolerances according to random
dispersions. Finally, from the two previous stages, the systematic
dispersions are generated. The objective of this study is to model
by the least squares method the error of manufacture based on
systematic dispersion. Finally, an approach of optimization of the
manufacturing tolerances was developed for machining on a CNC
machine tool
Abstract: This paper presents a particle swarm optimization
(PSO) based approach for multiple object tracking based on histogram
matching. To start with, gray-level histograms are calculated to
establish a feature model for each of the target object. The difference
between the gray-level histogram corresponding to each particle in the
search space and the target object is used as the fitness value. Multiple
swarms are created depending on the number of the target objects
under tracking. Because of the efficiency and simplicity of the PSO
algorithm for global optimization, target objects can be tracked as
iterations continue. Experimental results confirm that the proposed
PSO algorithm can rapidly converge, allowing real-time tracking of
each target object. When the objects being tracked move outside the
tracking range, global search capability of the PSO resumes to re-trace
the target objects.
Abstract: The corrugated steel cladding used to cover most of
steel buildings is considered as non-structural element. This research
will reflect the effect of cladding as a shear diaphragm in increasing
the normal elastic capacity of columns. This study is important
because of the lack of information of the behavior of cladding and
secondary members in various codes. Mathematical models for six
different cases are carried by software. The results extracted from the
program have been plotted showing the effects of different variables
on the ultimate load of column. The variables considered in our
research are the spacing between columns and the thickness of the
corrugated sheet representing the sheet stiffness.
Abstract: The study aimed to identify the nature of autistic
talent, the manifestations of their weak central coherence, and their
sensory characteristics. The case study consisted of four talented
autistic males. Two of them in drawing, one in clay formation and
one in jigsaw puzzle. Tools of data collection were Group Embedded
Figures Test, Block Design Test, Sensory Profile Checklist Revised,
Interview forms and direct observation. Results indicated that talent
among autistics emerges in limited domain and being extraordinary
for each case. Also overlapping construction properties. Indeed, they
show three perceptual aspects of weak central coherence: The weak
in visual spatial-constructional coherence, the weak in perceptual
coherence and the weak in verbal – semantic coherence. Moreover,
the majority of the study cases used the three strategies of weak
central coherence (segmentation, obliqueness and rotation). As for
the sensory characteristics, all study cases have numbers of that
characteristics that especially emerges in the visual system.
Abstract: Recently, the health of retired National Football
League players, particularly lineman has been investigated. A
number of studies have reported increased cardiometabolic risk,
premature cardiovascular disease and incidence of type 2 diabetes.
Rugby union players have somatotypes very similar to National
Football League players which suggests that rugby players may have
similar health risks. The International Golden Oldies World Rugby
Festival (GORF) provided a unique opportunity to investigate the
demographics of veteran rugby players. METHODOLOGIES: A
cross-sectional, observational study was completed using an online
web-based questionnaire that consisted of medical history and
physiological measures. Data analysis was completed using a one
sample t-test (50yrs) and Chi-square test. RESULTS:
A total of 216 veteran rugby competitors (response rate = 6.8%)
representing 10 countries, aged 35-72 yrs (mean 51.2, S.D. ±8.0),
participated in the online survey. As a group, the incidence of current
smokers was low at 8.8% (avg 72.4 cigs/wk) whilst the percentage
consuming alcohol was high (93.1% (avg 11.2 drinks/wk).
Competitors reported the following top six chronic
diseases/disorders; hypertension (18.6%), arthritis (OA/RA, 11.5%),
asthma (9.3%), hyperlipidemia (8.2%), diabetes (all types, 7.5%) and
gout (6%), there were significant differences between groups with
regard to cancer (all types) and migraines. When compared to the
Australian general population (Australian Bureau of Statistics data,
n=18,000), GORF competitors had a significantly lower incidence of
anxiety (p