Abstract: In order to find the particular interaction energy
between cylcloguanil and the amino acids surrounding the pocket of
wild type and quadruple mutant type PfDHFR enzymes, the MP2
method with basis set 6-31G(d,p) level of calculations was
performed. The obtained interaction energies found that Asp54 has
the strongest interaction energy to both wild type and mutant type of -
12.439 and -11.250 kcal/mol, respectively and three amino acids;
Asp54, Ile164 and Ile14 formed the H-bonding with cycloguanil
drug. Importantly, the mutation at Ser108Asn was the key important
of cycloguanil resistant with showing repulsive interaction energy.
Abstract: Hysteresis phenomenon has been observed in the
operations of both horizontal-axis and vertical-axis wind turbines
(HAWTs and VAWTs). In this study, wind tunnel experiments were
applied to investigate the characters of hysteresis phenomena between
the angular speed and the external resistance of electrical loading
during the operation of a Darrieus type VAWT. Data of output voltage,
output current, angular speed of wind turbine under different wind
speeds are measured and analyzed. Results show that the range of
external resistance changes with the wind speed. The range decreases
as the wind speed increases following an exponential decay form.
Experiments also indicate that the maximum output power of wind
turbines is always inside the range where hysteresis happened. These
results provide an important reference to the design of output control
system of wind turbines.
Abstract: Low carbon deep drawing steel DC 01 according to EN 10130-91 was nitrooxidized in dissociated ammonia at 580°C/45 min and consequently oxidised at 380°C/5 min in vapour of distilled water. Material after nitrooxidation had 54 % increase of yield point, 34 % increase of strength and 10-times increased resistance to atmospheric corrosion in comparison to the material before nitrooxidation. The microstructure of treated material consisted of thin ε-phase layer connected to layer containing precipitated massive needle shaped Fe4N - γ' nitrides. This layer passed to a diffusion layer consisting of fine irregular shaped Fe16N2 - α'' nitrides regularly dispersed in ferritic matrix. Fatigue properties were examined under bending load with frequency of 20 kHz and sinusoidal symmetric cycle. The results confirmed positive influence of nitrooxidation on fatigue properties as fatigue limit of treated material was double in comparison to untreated material.
Abstract: Increasing growth of information volume in the
internet causes an increasing need to develop new (semi)automatic
methods for retrieval of documents and ranking them according to
their relevance to the user query. In this paper, after a brief review
on ranking models, a new ontology based approach for ranking
HTML documents is proposed and evaluated in various
circumstances. Our approach is a combination of conceptual,
statistical and linguistic methods. This combination reserves the
precision of ranking without loosing the speed. Our approach
exploits natural language processing techniques for extracting
phrases and stemming words. Then an ontology based conceptual
method will be used to annotate documents and expand the query.
To expand a query the spread activation algorithm is improved so
that the expansion can be done in various aspects. The annotated
documents and the expanded query will be processed to compute
the relevance degree exploiting statistical methods. The outstanding
features of our approach are (1) combining conceptual, statistical
and linguistic features of documents, (2) expanding the query with
its related concepts before comparing to documents, (3) extracting
and using both words and phrases to compute relevance degree, (4)
improving the spread activation algorithm to do the expansion based
on weighted combination of different conceptual relationships and
(5) allowing variable document vector dimensions. A ranking
system called ORank is developed to implement and test the
proposed model. The test results will be included at the end of the
paper.
Abstract: Full adders are important components in applications
such as digital signal processors (DSP) architectures and
microprocessors. In addition to its main task, which is adding two
numbers, it participates in many other useful operations such as
subtraction, multiplication, division,, address calculation,..etc. In
most of these systems the adder lies in the critical path that
determines the overall speed of the system. So enhancing the
performance of the 1-bit full adder cell (the building block of the
adder) is a significant goal.Demands for the low power VLSI have
been pushing the development of aggressive design methodologies to
reduce the power consumption drastically. To meet the growing
demand, we propose a new low power adder cell by sacrificing the
MOS Transistor count that reduces the serious threshold loss
problem, considerably increases the speed and decreases the power
when compared to the static energy recovery full (SERF) adder. So a
new improved 14T CMOS l-bit full adder cell is presented in this
paper. Results show 50% improvement in threshold loss problem,
45% improvement in speed and considerable power consumption
over the SERF adder and other different types of adders with
comparable performance.
Abstract: Among all mechanical joining processes, welding has
been employed for its advantage in design flexibility, cost saving,
reduced overall weight and enhanced structural performance.
However, for structures made of relatively thin components, welding
can introduce significant buckling distortion which causes loss of
dimensional control, structural integrity and increased fabrication
costs. Different parameters can affect buckling behavior of welded
thin structures such as, heat input, welding sequence, dimension of
structure. In this work, a 3-D thermo elastic-viscoplastic finite
element analysis technique is applied to evaluate the effect of shell
dimensions on buckling behavior and entropy generation of welded
thin shells. Also, in the present work, the approximated longitudinal
transient stresses which produced in each time step, is applied to the
3D-eigenvalue analysis to ratify predicted buckling time and
corresponding eigenmode. Besides, the possibility of buckling
prediction by entropy generation at each time is investigated and it is
found that one can predict time of buckling with drawing entropy
generation versus out of plane deformation. The results of finite
element analysis show that the length, span and thickness of welded
thin shells affect the number of local buckling, mode shape of global
buckling and post-buckling behavior of welded thin shells.
Abstract: A considerable progress has been achieved in transient
stability analysis (TSA) with various FACTS controllers. But, all
these controllers are associated with single transmission line. This
paper is intended to discuss a new approach i.e. a multi-line FACTS
controller which is interline power flow controller (IPFC) for TSA of
a multi-machine power system network. A mathematical model of
IPFC, termed as power injection model (PIM) presented and this
model is incorporated in Newton-Raphson (NR) power flow
algorithm. Then, the reduced admittance matrix of a multi-machine
power system network for a three phase fault without and with IPFC
is obtained which is required to draw the machine swing curves. A
general approach based on L-index has also been discussed to find
the best location of IPFC to reduce the proximity to instability of a
power system. Numerical results are carried out on two test systems
namely, 6-bus and 11-bus systems. A program in MATLAB has
been written to plot the variation of generator rotor angle and speed
difference curves without and with IPFC for TSA and also a simple
approach has been presented to evaluate critical clearing time for test
systems. The results obtained without and with IPFC are compared
and discussed.
Abstract: India recognizes the personal laws of the various
religious communities that reside in the country. At the same time all
the institutions of the state in India are committed to the value of
secularism. This paper has been developed on the basis of a case
study that indicates the dynamics of religion in the working of the
lower judiciary in India. Majority of the commentary on religion and
the judiciary has focused on debates surrounding the existence and
application of personal laws. This paper, through a case study in the
lower judiciary, makes an attempt to examine whether the interface
between religion and the judiciary goes beyond personal laws.
The first part of this paper explains the history and application of
personal laws in social, political and legal contexts in India. The
second part examines the case study located in two courts of first
instance, following into the third part which provides an analysis of
the empirical evidence. The fourth part focuses on preliminary
observations about why there is a hesitancy to speak about religion in
relation to the working of the judicial system.
Abstract: The development of the poultry industry in Albania is mainly based on the existence of intensive modern farms with huge capacities, which often are mixed with other forms. Colibacillosis is commonly displayed regardless of the type of breeding, delivering high mortality in poultry industry. The mechanisms with which pathogen enterobacters are able to cause the infection in poultry are not yet clear. The routine diagnose in the field, followed by isolation of E. coli and species of Salmonella genres in reference laboratories cannot lead in classification or full recognition of circulative strains in a territory, if it is not performed a differentiation among the present microorganisms in intensive farms and those in rural areas. In this study were isolated 1.496 strains of E. coli and 378 Salmonella spp. This study, presents distribution of poultry pathogenosity of E.coli and Salmonella spp., based on the usage of innovative diagnostic methods.
Abstract: The latest Geographic Information System (GIS)
technology makes it possible to administer the spatial components of
daily “business object," in the corporate database, and apply suitable
geographic analysis efficiently in a desktop-focused application. We
can use wireless internet technology for transfer process in spatial
data from server to client or vice versa. However, the problem in
wireless Internet is system bottlenecks that can make the process of
transferring data not efficient. The reason is large amount of spatial
data. Optimization in the process of transferring and retrieving data,
however, is an essential issue that must be considered. Appropriate
decision to choose between R-tree and Quadtree spatial data indexing
method can optimize the process. With the rapid proliferation of
these databases in the past decade, extensive research has been
conducted on the design of efficient data structures to enable fast
spatial searching. Commercial database vendors like Oracle have also
started implementing these spatial indexing to cater to the large and
diverse GIS. This paper focuses on the decisions to choose R-tree
and quadtree spatial indexing using Oracle spatial database in mobile
GIS application. From our research condition, the result of using
Quadtree and R-tree spatial data indexing method in one single
spatial database can save the time until 42.5%.
Abstract: Typical Intelligent Decision Support System is 4-based, its design composes of Data Warehouse, Online Analytical Processing, Data Mining and Decision Supporting based on models, which is called Decision Support System Based on Data Warehouse (DSSBDW). This way takes ETL,OLAP and DM as its implementing means, and integrates traditional model-driving DSS and data-driving DSS into a whole. For this kind of problem, this paper analyzes the DSSBDW architecture and DW model, and discusses the following key issues: ETL designing and Realization; metadata managing technology using XML; SQL implementing, optimizing performance, data mapping in OLAP; lastly, it illustrates the designing principle and method of DW in DSSBDW.
Abstract: The brain MR imaging-based clinical research and analysis system were specifically built and the development for a large-scale data was targeted. We used the general clinical data available for building large-scale data. Registration period for the selection of the lesion ROI and the region growing algorithm was used and the Mesh-warp algorithm for matching was implemented. The accuracy of the matching errors was modified individually. Also, the large ROI research data can accumulate by our developed compression method. In this way, the correctly decision criteria to the research result was suggested. The experimental groups were age, sex, MR type, patient ID and smoking which can easily be queries. The result data was visualized of the overlapped images by a color table. Its data was calculated by the statistical package. The evaluation for the utilization of this system in the chronic ischemic damage in the area has done from patients with the acute cerebral infarction. This is the cause of neurologic disability index location in the center portion of the lateral ventricle facing. The corona radiate was found in the position. Finally, the system reliability was measured both inter-user and intra-user registering correlation.
Abstract: Nowadays, cardiac disease is one of the most common
cause of death. Each year almost one million of angioplasty interventions and stents implantations are made all over the world.
Unfortunately, in 20-30% of cases neointimal proliferations leads to
restenosis occurring within the following period of 3-6 months. Three major factors are believed to contribute mostly to the edge
restenosis: (a) mechanical damage of the artery-s wall caused by the
stent implantation, (b) interaction between the stent and the blood constituents and (c) endothelial growth stimulation by small (lower
that 1.5 Pa) and oscillating wall shear stress. Assuming that this last actor is particularly important, a numerical model of restenosis
basing on wall shear stress distribution in the stented artery was elaborated. A numerical simulations of the development of in-stent
restenosis have been performed and realistic geometric patterns of a
progressing lumen reduction have been obtained
Abstract: An important goal of parboiling is a decrease of rice broken percentage and at the beginning Selected paddy of variety of rice Tarom and soaked at three different temperatures 45 Cº, 65 Cº and 80 Cº orderly for 5 hours, 4 hours and 1.5 hours to moisture of 40 % and then in steaming stage to operate these action two steaming methods are selected steaming under pressure condition and steaming in atmosphere pressure and In the first method after exerting air, the steam pressure is increase to 1 Kg/Cm2 which is done in two different duration times of 2.5 and 5 minutes and in second method used of three times of 5,10 and 15 minutes and dry to 8% moisture and decreases of rice broken percentage at best condition in variety of Tarom of 37.2 % to 7.3 % and increases yield percentage at best condition in variety of Tarom of 69.4 % to 75.93 % and bran percentage decreased in variety of Tarom of 9.53 % to 2.2-3.2 % and this issue cause increases yield percentage in rice and use of This method is very significant for our country because broken percentage of rice in our country is 23-33 %.
Abstract: Vertical Double Gate (DG) Metal Oxide Semiconductor Field Effect Transistor (MOSFET) is believed to suppress various short channel effect problems. The gate to channel coupling in vertical DG-MOSFET are doubled, thus resulting in higher current density. By having two gates, both gates are able to control the channel from both sides and possess better electrostatic control over the channel. In order to ensure that the transistor possess a superb turn-off characteristic, the subs-threshold swing (SS) must be kept at minimum value (60-90mV/dec). By utilizing SILVACO TCAD software, an n-channel vertical DG-MOSFET was successfully designed while keeping the sub-threshold swing (SS) value as minimum as possible. From the observation made, the value of sub-threshold swing (SS) was able to be varied by adjusting the height of the silicon pillar. The minimum value of sub-threshold swing (SS) was found to be 64.7mV/dec with threshold voltage (VTH) of 0.895V. The ideal height of the vertical DG-MOSFET pillar was found to be at 0.265 µm.
Abstract: Pregnancy is considered a special period in a woman’s life. There are myths about pregnancy that describe gender predictions, dietary beliefs, pregnancy signs, and risk of magic or witchcraft. Majority of these myths is in connection with the early childcare. In traditional societies midwives and experienced women practice and teach these myths to young mothers. Mother who feel special and vulnerable, at the same time feel secure in following these socially transmitted myths. Rural Punjab, a province of Pakistan has a culture rich with beliefs and myths. Myths about pregnancy are significant in rural culture and pregnancy care is seen as mother and childcare. This paper presents my research reflections that I did as a part of my Ph.D studies about early childcare beliefs and rituals practiced in rural Punjab, Pakistan.
Abstract: In general fuzzy sets are used to analyze the fuzzy
system reliability. Here intuitionistic fuzzy set theory for analyzing
the fuzzy system reliability has been used. To analyze the fuzzy
system reliability, the reliability of each component of the system as
a triangular intuitionistic fuzzy number is considered. Triangular
intuitionistic fuzzy number and their arithmetic operations are
introduced. Expressions for computing the fuzzy reliability of a
series system and a parallel system following triangular intuitionistic
fuzzy numbers have been described. Here an imprecise reliability
model of an electric network model of dark room is taken. To
compute the imprecise reliability of the above said system, reliability
of each component of the systems is represented by triangular
intuitionistic fuzzy numbers. Respective numerical example is
presented.
Abstract: The issue of leadership has been investigated from
several perspectives; however, very less from ethical perspective.
With the growing number of corporate scandals and unethical roles
played by business leaders in several parts of the world, the need to
examine leadership from ethical perspective cannot be over
emphasized. The importance of leadership credibility has been
discussed in the authentic model of leadership. Authentic leaders
display high degree of integrity, have deep sense of purpose, and
committed to their core values. As a result they promote a more
trusting relationship in their work groups that translates into several
positive outcomes. The present study examined how authentic
leadership contribute to subordinates- trust in leadership and how this
trust, in turn, predicts subordinates- work engagement. A sample of
395 employees was randomly selected from several local banks
operating in Malaysia. Standardized tools such as ALQ, OTI, and
EEQ were employed. Results indicated that authentic leadership
promoted subordinates- trust in leader, and contributed to work
engagement. Also, interpersonal trust predicted employees- work
engagement as well as mediated the relationship between this style of
leadership and employees- work engagement.
Abstract: In the field of concepts, the measure of Wu and Palmer [1] has the advantage of being simple to implement and have good performances compared to the other similarity measures [2]. Nevertheless, the Wu and Palmer measure present the following disadvantage: in some situations, the similarity of two elements of an IS-A ontology contained in the neighborhood exceeds the similarity value of two elements contained in the same hierarchy. This situation is inadequate within the information retrieval framework. To overcome this problem, we propose a new similarity measure based on the Wu and Palmer measure. Our objective is to obtain realistic results for concepts not located in the same way. The obtained results show that compared to the Wu and Palmer approach, our measure presents a profit in terms of relevance and execution time.
Abstract: Water quality and freshwater fish diversity from nine
waterfalls at Khao Luang National Park, Thailand was examined.
Streams were shallow, fast flowing with clear water and rocky and
sandy substrate. The mean water quality of waterfalls at Khao Luang
National Park were as following pH 7.50, air temperature 24.27 °C,
water temperature 26.37 °C, dissolved oxygen 7.88 mg/l, hardness
4.44-21.33 mg/l, alkalinity 3.55-11.88 mg/(as CaCO3). Twenty fish
species were found at Khao Luang National Park belonging to nine
families. A cluster analysis of water quality at Khao Luang National
Park revealed that waterfalls at Khao Luang National Park were
divided into two groups: A and B. Group A composed of two
waterfalls (i.e. Aie Kaew and Wangmaipak) that flew to the Gulf of
Thailand side. Group B composed of seven waterfalls (i.e. Promlok,
Kalom, Nuafa, Suankun, Soidaw, Suanhai, and Thapae) that flew to
the Andaman Sea side (Fig. 2) .The Cyprinids represented the major
species in all the waterfalls comprising of 45%.