Abstract: The major urban centers are all facing rapid growth is
most often associated with spreading urbanization, social status of the
car has also changed: it has become a commodity of mass
consumption. There are currently about 5 million and 260 cars in
Algeria (2008), this number increases every year 200,000 new cars.
These phenomena induce a demand for greater mobility and a
significant need for transport infrastructure. Faced with these
problems and development of the growing use of the automobile,
central governments and local authorities in charge of urban transport
issues are aware of the need to develop their urban transport systems
but often lack opportunities.
Urban Transport Plans (PDU) were born in reaction to the "culture
of automobile." Their existence in the world the '80s, however, they
had little success before laws on air and rational use of energy in 90
years does not alter substantially their content and make mandatory
their implementation in cities of over 100,000 inhabitants (Abroad)
[1].
The objective of this work is to use the tool and specifically
Geomatics techniques as decision support in the organization and
management of travel while taking into consideration the influence,
which will then translate by National Urban Transport Plan.
Abstract: This paper is concerned with the study of mineralogy
and engineering characteristics of soil materials derived from the
eastern part of Nile Delta. The clay minerals of the studied soil by
using X- ray diffraction are mainly illite (average 72.6 %) and
kaolinite (average 2.6 %), expandable portion in illite-smectite mixed
layer (average 7 %). Smectite is more abundant in fluviatile clays,
whereas kaolinite is more abundant in lagoonal clays. On the other
hand, illite and illite-smectite are more abundant in marine clays. The
geotechnical results show that the soil under study consists mainly of
about 0.3 % gravel, 5 % sand, 51.5 % silt and 42.2 % clay in average.
The average shrinkage limit attains 11 % whereas the average value
of the plasticity index is 23.4 %. The free swelling ranges from 40 %
to 75 % and has a value of 55 % giving an indication about the
inadequacy of such soil under foundations.
From a construction point of view, the soil under investigation
poses many problems even under light foundations due to the
swelling and shrinkage. Such swelling and shrinkage is due to the
high content of soil materials in the expandable clay minerals of illite
and smectite. Based on the results of the present and earlier studies,
trial application of soil stabilisation is recommended.
Abstract: The mountain road slope failures triggered by
earthquake activities and torrential rain namely to create the disaster.
Province Road No. 24 is a main route to the Wutai Township. The area
of the study is located at the mileages between 46K and 47K along the
road. However, the road has been suffered frequent damages as a result
of landslide and slope failures during typhoon seasons. An
understanding of the sliding behaviors in the area appears to be
necessary. Slope failures triggered by earthquake activities and heavy
rainfalls occur frequently. The study is to understand the mechanism
of slope failures and to look for the way to deal with the situation. In
order to achieve these objectives, this paper is based on theoretical and
structural geology data interpretation program to assess the potential
slope sliding behavior. The study showed an intimate relationship
between the landslide behavior of the slopes and the stratum materials,
based on structural geology analysis method to analysis slope stability
and finds the slope safety coefficient to predict the sites of destroyed
layer. According to the case study and parameter analyses results, the
slope mainly slips direction compared to the site located in the
southeast area. Find rainfall to result in the rise of groundwater level is
main reason of the landslide mechanism. Future need to set up
effective horizontal drain at corrective location, that can effective
restrain mountain road slope failures and increase stability of slope.
Abstract: The present paper reports results of an experimental
program conducted to study performance of fly ash based
geopolymer pastes at elevated temperature. Three series of
geopolymer pastes differing in Na2O content (8.5%, 10% and 11.5%)
were manufactured by activating low calcium fly ash with a mixture
of sodium hydroxide and sodium silicate solution. The paste
specimens were subjected to temperatures as high as 900oC and the
behaviour at elevated temperatures were investigated on the basis of
physical appearance, weight losses, residual strength, shrinkage
measurements and sorptivity tests at different temperatures. Scanning
electron microscopy along with EDX and XRD tests were also
conducted to examine microstructure and mineralogical changes
during the thermal exposure. Specimens which were initially grey
turned reddish accompanied by appearance of small cracks as the
temperature increased to 900oC. Loss of weight was more in
specimens manufactured with highest Na2O content. Geopolymer
paste specimen containing minimum Na2O performed better than
those with higher Na2O content in terms of residual compressive
strength.
Abstract: Designing modern machine tools is a complex task. A
simulation tool to aid the design work, a virtual machine, has
therefore been developed in earlier work. The virtual machine
considers the interaction between the mechanics of the machine
(including structural flexibility) and the control system. This paper
exemplifies the usefulness of the virtual machine as a tool for product
development. An optimisation study is conducted aiming at
improving the existing design of a machine tool regarding weight and
manufacturing accuracy at maintained manufacturing speed. The
problem can be categorised as constrained multidisciplinary multiobjective
multivariable optimisation. Parameters of the control and
geometric quantities of the machine are used as design variables. This
results in a mix of continuous and discrete variables and an
optimisation approach using a genetic algorithm is therefore
deployed. The accuracy objective is evaluated according to
international standards. The complete systems model shows nondeterministic
behaviour. A strategy to handle this based on statistical
analysis is suggested. The weight of the main moving parts is reduced
by more than 30 per cent and the manufacturing accuracy is
improvement by more than 60 per cent compared to the original
design, with no reduction in manufacturing speed. It is also shown
that interaction effects exist between the mechanics and the control,
i.e. this improvement would most likely not been possible with a
conventional sequential design approach within the same time, cost
and general resource frame. This indicates the potential of the virtual
machine concept for contributing to improved efficiency of both
complex products and the development process for such products.
Companies incorporating such advanced simulation tools in their
product development could thus improve its own competitiveness as
well as contribute to improved resource efficiency of society at large.
Abstract: Geographic Profiling has successfully assisted investigations for serial crimes. Considering the multi-cluster feature of serial criminal spots, we propose a Multi-point Centrography model as a natural extension of Single-point Centrography for geographic profiling. K-means clustering is first performed on the data samples and then Single-point Centrography is adopted to derive a probability distribution on each cluster. Finally, a weighted combinations of each distribution is formed to make next-crime spot prediction. Experimental study on real cases demonstrates the effectiveness of our proposed model.
Abstract: It is an important problem to compute the geodesics on
a surface in many fields. To find the geodesics in practice, however,
the traditional discrete algorithms or numerical approaches can only
find a list of discrete points. The first author proposed in 2010 a new,
elegant and accurate method, the geodesic-like method, for
approximating geodesics on a regular surface. This paper will present
by use of this method a computation of the Bezier geodesic-like curves
on spheres.
Abstract: Real options theory suggests that managerial flexibility embedded within irreversible investments can account for a significant value in project valuation. Although the argument has become the dominant focus of capital investment theory over decades, yet recent survey literature in capital budgeting indicates that corporate practitioners still do not explicitly apply real options in investment decisions. In this paper, we explore how real options decision criteria can be transformed into equivalent capital budgeting criteria under the consideration of uncertainty, assuming that underlying stochastic process follows a geometric Brownian motion (GBM), a mixed diffusion-jump (MX), or a mean-reverting process (MR). These equivalent valuation techniques can be readily decomposed into conventional investment rules and “option impacts", the latter of which describe the impacts on optimal investment rules with the option value considered. Based on numerical analysis and Monte Carlo simulation, three major findings are derived. First, it is shown that real options could be successfully integrated into the mindset of conventional capital budgeting. Second, the inclusion of option impacts tends to delay investment. It is indicated that the delay effect is the most significant under a GBM process and the least significant under a MR process. Third, it is optimal to adopt the new capital budgeting criteria in investment decision-making and adopting a suboptimal investment rule without considering real options could lead to a substantial loss in value.
Abstract: In this paper, numerical simulation is used to
investigate the thermal performance of liquid cooling heatsink with
microchannels due to geometric arrangement. Commercial software
ICEPAK is utilized for the analysis. The considered parameters
include aspect ratio, porosity and the length and height of
microchannel. The aspect ratio varies from 3 to 16 and the length of
microchannel is 10mm, 14mm, and 18mm. The height of
microchannel is 2mm, 3mm and 4mm. It is found short channel have
better thermal efficiency than long channel at 490Pa. No matter the
length of channel the best aspect ratio is 4. It is also noted that pressure
difference at 2940Pa the best aspect ratio from 4 to 8, it means pressure
difference affect aspect ratio, effective thermal resistance at low
pressure difference but lower effective thermal resistance at high
pressure difference.
Abstract: Turbulence modeling of large-scale flow over a vegetated surface is complex. Such problems involve large scale computational domains, while the characteristics of flow near the surface are also involved. In modeling large scale flow, surface roughness including vegetation is generally taken into account by mean of roughness parameters in the modified law of the wall. However, the turbulence structure within the canopy region cannot be captured with this method, another method which applies source/sink terms to model plant drag can be used. These models have been developed and tested intensively but with a simple surface geometry. This paper aims to compare the use of roughness parameter, and additional source/sink terms in modeling the effect of plant drag on wind flow over a complex vegetated surface. The RNG k-ε turbulence model with the non-equilibrium wall function was tested with both cases. In addition, the k-ω turbulence model, which is claimed to be computationally stable, was also investigated with the source/sink terms. All numerical results were compared to the experimental results obtained at the study site Mason Bay, Stewart Island, New Zealand. In the near-surface region, it is found that the results obtained by using the source/sink term are more accurate than those using roughness parameters. The k-ω turbulence model with source/sink term is more appropriate as it is more accurate and more computationally stable than the RNG k-ε turbulence model. At higher region, there is no significant difference amongst the results obtained from all simulations.
Abstract: Estimation of natural frequency of structures is very
important and isn-t usually calculated simply and sometimes
complicated. Lack of knowledge about that caused hard damage and
hazardous effects.
In this paper, with using from two different models in FEM
method and based on hydrodynamic mass of fluids, natural frequency
of an especial bearing (Fig. 1) in an electric field (or, a periodic
force) is calculated in different stiffness and different geometric. In
final, the results of two models and analytical solution are compared.
Abstract: In this paper, we present a robust and secure
algorithm for watermarking, the watermark is first transformed into
the frequency domain using the discrete wavelet transform (DWT).
Then the entire DWT coefficient except the LL (Band) discarded,
these coefficients are permuted and encrypted by specific mixing.
The encrypted coefficients are inserted into the most significant
spectral components of the stego-image using a chaotic system. This
technique makes our watermark non-vulnerable to the attack (like
compression, and geometric distortion) of an active intruder, or due
to noise in the transmission link.
Abstract: In this study the mixed mode fracture mechanics
parameters were investigated for high tensile steel butt welded joint
based on modified Arcan test and finite element analysis was used to
evaluate the effect of crack length on fracture criterion. The nondimensional
stress intensity factors, strain energy release rates and Jintegral
energy on crack tip were obtained for various in-plane
loading combinations on Arcan specimen starting from pure mode-I
to pure mode-II loading conditions. The specimen and apparatus were
modeled by finite element method and analyzed under various
loading angles (between 0 to 90 degrees with 15 degree interval) to
simulate the pure mode-I, II and mixed mode fracture. Since the
analytical results are independent from elasticity modules for
isotropic materials, therefore the results in elastic fields can be used
for Arcan specimens. The main objective of this study was to
evaluate the geometric calibration factors for modified Arcan test
specimen in order to obtain fracture toughness under mixed mode
loading conditions.
Abstract: We proposed a technique to identify road traffic
congestion levels from velocity of mobile sensors with high accuracy
and consistent with motorists- judgments. The data collection utilized
a GPS device, a webcam, and an opinion survey. Human perceptions
were used to rate the traffic congestion levels into three levels: light,
heavy, and jam. Then the ratings and velocity were fed into a
decision tree learning model (J48). We successfully extracted vehicle
movement patterns to feed into the learning model using a sliding
windows technique. The parameters capturing the vehicle moving
patterns and the windows size were heuristically optimized. The
model achieved accuracy as high as 99.68%. By implementing the
model on the existing traffic report systems, the reports will cover
comprehensive areas. The proposed method can be applied to any
parts of the world.
Abstract: The use of amine mixtures employing
methyldiethanolamine (MDEA), monoethanolamine (MEA), and diethanolamine (DEA) have been investigated for a variety of cases
using a process simulation program called HYSYS. The results show that, at high pressures, amine mixtures have little or no advantage in the cases studied. As the pressure is lowered, it becomes more difficult for MDEA to meet residual gas requirements and mixtures can usually improve plant performance. Since the CO2 reaction rate
with the primary and secondary amines is much faster than with
MDEA, the addition of small amounts of primary or secondary amines to an MDEA based solution should greatly improve the overall reaction rate of CO2 with the amine solution. The addition of MEA caused the CO2 to be absorbed more strongly in the upper portion of the column than for MDEA along. On the other hand,
raising the concentration for MEA to 11%wt, CO2 is almost
completely absorbed in the lower portion of the column. The addition of MEA would be most advantageous.
Thus, in areas where MDEA cannot meet the residual gas
requirements, the use of amine mixtures can usually improve the plant
performance.
Abstract: In this paper, to optimize the “Characteristic Straight Line Method" which is used in the soil displacement analysis, a “best estimate" of the geodetic leveling observations has been achieved by taking in account the concept of 'Height systems'. This concept has been discussed in detail and consequently the concept of “height". In landslides dynamic analysis, the soil is considered as a mosaic of rigid blocks. The soil displacement has been monitored and analyzed by using the “Characteristic Straight Line Method". Its characteristic components have been defined constructed from a “best estimate" of the topometric observations. In the measurement of elevation differences, we have used the most modern leveling equipment available. Observational procedures have also been designed to provide the most effective method to acquire data. In addition systematic errors which cannot be sufficiently controlled by instrumentation or observational techniques are minimized by applying appropriate corrections to the observed data: the level collimation correction minimizes the error caused by nonhorizontality of the leveling instrument's line of sight for unequal sight lengths, the refraction correction is modeled to minimize the refraction error caused by temperature (density) variation of air strata, the rod temperature correction accounts for variation in the length of the leveling rod' s Invar/LO-VAR® strip which results from temperature changes, the rod scale correction ensures a uniform scale which conforms to the international length standard and the introduction of the concept of the 'Height systems' where all types of height (orthometric, dynamic, normal, gravity correction, and equipotential surface) have been investigated. The “Characteristic Straight Line Method" is slightly more convenient than the “Characteristic Circle Method". It permits to evaluate a displacement of very small magnitude even when the displacement is of an infinitesimal quantity. The inclination of the landslide is given by the inverse of the distance reference point O to the “Characteristic Straight Line". Its direction is given by the bearing of the normal directed from point O to the Characteristic Straight Line (Fig..6). A “best estimate" of the topometric observations was used to measure the elevation of points carefully selected, before and after the deformation. Gross errors have been eliminated by statistical analyses and by comparing the heights within local neighborhoods. The results of a test using an area where very interesting land surface deformation occurs are reported. Monitoring with different options and qualitative comparison of results based on a sufficient number of check points are presented.
Abstract: The purpose of this paper is to perform a multidisciplinary design and analysis (MDA) of honeycomb panels used in the satellites structural design. All the analysis is based on clamped-free boundary conditions. In the present work, detailed finite element models for honeycomb panels are developed and analysed. Experimental tests were carried out on a honeycomb specimen of which the goal is to compare the previous modal analysis made by the finite element method as well as the existing equivalent approaches. The obtained results show a good agreement between the finite element analysis, equivalent and tests results; the difference in the first two frequencies is less than 4% and less than 10% for the third frequency. The results of the equivalent model presented in this analysis are obtained with a good accuracy. Moreover, investigations carried out in this research relate to the honeycomb plate modal analysis under several aspects including the structural geometrical variation by studying the various influences of the dimension parameters on the modal frequency, the variation of core and skin material of the honeycomb. The various results obtained in this paper are promising and show that the geometry parameters and the type of material have an effect on the value of the honeycomb plate modal frequency.
Abstract: Automatic segmentation of skin lesions is the first step
towards development of a computer-aided diagnosis of melanoma.
Although numerous segmentation methods have been developed,
few studies have focused on determining the most discriminative
and effective color space for melanoma application. This paper
proposes a novel automatic segmentation algorithm using color space
analysis and clustering-based histogram thresholding, which is able to
determine the optimal color channel for segmentation of skin lesions.
To demonstrate the validity of the algorithm, it is tested on a set of 30
high resolution dermoscopy images and a comprehensive evaluation
of the results is provided, where borders manually drawn by four
dermatologists, are compared to automated borders detected by the
proposed algorithm. The evaluation is carried out by applying three
previously used metrics of accuracy, sensitivity, and specificity and
a new metric of similarity. Through ROC analysis and ranking the
metrics, it is shown that the best results are obtained with the X and
XoYoR color channels which results in an accuracy of approximately
97%. The proposed method is also compared with two state-ofthe-
art skin lesion segmentation methods, which demonstrates the
effectiveness and superiority of the proposed segmentation method.
Abstract: Modeling of Panel Zone (PZ) seismic behavior,
because of its role in overall ductility and lateral stiffness of steel
moment frames, has been considered a challenge for years. There are
some studies regarding the effects of different doubler plates
thicknesses and geometric properties of PZ on its seismic behavior.
However, there is not much investigation on the effects of number of
provided continuity plates in case of presence of one triangular
haunch, two triangular haunches and rectangular haunch (T shape
haunches) for exterior columns. In this research first detailed finite
element models of 12tested connection of SAC joint venture were
created and analyzed then obtained cyclic behavior backbone curves
of these models besides other FE models for similar tests were used
for neural network training. Then seismic behavior of these data is
categorized according to continuity plate-s arrangements and
differences in type of haunches. PZ with one-sided haunches have
little plastic rotation. As the number of continuity plates increases
due to presence of two triangular haunches (four continuity plate),
there will be no plastic rotation, in other words PZ behaves in its
elastic range. In the case of rectangular haunch, PZ show more plastic
rotation in comparison with one-sided triangular haunch and
especially double-sided triangular haunches. Moreover, the models
that will be presented in case of triangular one-sided and double-
sided haunches and rectangular haunches as a result of this study
seem to have a proper estimation of PZ seismic behavior.
Abstract: Ontology is a terminology which is used in artificial
intelligence with different meanings. Ontology researching has an
important role in computer science and practical applications,
especially distributed knowledge systems. In this paper we present an
ontology which is called Computational Object Knowledge Base
Ontology. It has been used in designing some knowledge base
systems for solving problems such as the system that supports
studying knowledge and solving analytic geometry problems, the
program for studying and solving problems in Plane Geometry, the
knowledge system in linear algebra.