Abstract: Aim of this work is to determine the theoretical and
experimental properties of filament wound glass fiber/epoxy resin
composite pipes with different winding design subjected under
bending. For determination of bending strength of composite samples
three point bending tests were conducted. Good correlation between
theoretical and experimental results has been obtained, where sample
No4 has shown the highest value of bending strength. All samples
have demonstrated matrix cracking and fiber failure followed by
layers delamination during testing. Also, it was found that smaller
winding angles lead to an increase in bending stress. From presented
results good merger between glass fibers and epoxy resin was
confirmed by SEM analysis.
Abstract: Non-crimp 3D orthogonal fabric composite is one of
the textile-based composite materials that are rapidly developing
light-weight engineering materials. The present paper focuses on
geometric and micromechanical modeling of non-crimp 3D
orthogonal carbon fabric and composites reinforced with it for
aerospace applications. In this research meso-finite element (FE)
modeling employs for stress analysis in different load conditions.
Since mechanical testing of expensive textile carbon composites with
specific application isn't affordable, simulation composite in a virtual
environment is a helpful way to investigate its mechanical properties
in different conditions.
Abstract: This article presents two methods for the
compensation of harmonics generated by a nonlinear load. The first is
the classic method P-Q. The second is the controller by modern
method of artificial intelligence specifically fuzzy logic. Both
methods are applied to a shunt Active Power Filter (sAPF) based on a
three-phase voltage converter at five levels NPC topology. In
calculating the harmonic currents of reference, we use the algorithm
P-Q and pulse generation, we use the intersective PWM. For
flexibility and dynamics, we use fuzzy logic. The results give us clear
that the rate of Harmonic Distortion issued by fuzzy logic is better
than P-Q.
Abstract: Chitosan functionalized Fe3O4-Au core shell
nanoparticles have been prepared using a two-step wet chemical
approach using NaBH4 as reducing agent for formation of Au in
ethylene glycol. X-ray diffraction studies shows individual phases of
Fe3O4 and Au in the as prepared samples with crystallite size of 5.9
and 11.4 nm respectively. The functionalization of the core-shell
nanostructure with Chitosan has been confirmed using Fourier
transform infrared spectroscopy along with signatures of octahedral
and tetrahedral sites of Fe3O4 below 600cm-1. Mössbauer
spectroscopy shows decrease in particle-particle interaction in
presence of Au shell (72% sextet) than pure oleic coated Fe3O4
nanoparticles (88% sextet) at room temperature. At 80K, oleic acid
coated Fe3O4 shows only sextets whereas the Chitosan functionalized
Fe3O4 and Chitosan functionalized Fe3O4@Au core shell show
presence of 5 and 11% doublet, respectively.
Abstract: Here, we study the characteristic feature of
conventional (ON-OFF keying) and soliton based transmission
system. We consider 20Gbps transmission system implemented with
Conventional Single Mode Fiber (C-SMF) to examine the role of
Gaussian pulse which is the characteristic of conventional
propagation and Hyperbolic-secant pulse which is the characteristic
of soliton propagation in it. We note the influence of these pulses
with respect to different dispersion lengths and soliton period in
conventional and soliton system respectively and evaluate the system
performance in terms of Quality factor. From the analysis, we could
prove that the soliton pulse has the consistent performance even for
long distance without dispersion compensation than the conventional
system as it is robust to dispersion. For the length of transmission of
200Km, soliton system yielded Q of 33.958 while the conventional
system totally exhausted with Q=0.
Abstract: In the present study, RBF neural networks were used
for predicting the performance and emission parameters of a
biodiesel engine. Engine experiments were carried out in a 4 stroke
diesel engine using blends of diesel and Honge methyl ester as the
fuel. Performance parameters like BTE, BSEC, Tex and emissions
from the engine were measured. These experimental results were
used for ANN modeling.
RBF center initialization was done by random selection and by
using Clustered techniques. Network was trained by using fixed and
varying widths for the RBF units. It was observed that RBF results
were having a good agreement with the experimental results.
Networks trained by using clustering technique gave better results
than using random selection of centers in terms of reduced MRE and
increased prediction accuracy. The average MRE for the performance
parameters was 3.25% with the prediction accuracy of 98% and for
emissions it was 10.4% with a prediction accuracy of 80%.
Abstract: To understand the friction stir welding process, it is
very important to know the nature of the material flow in and around
the tool. The process is a combination of both thermal as well as
mechanical work i.e. it is a coupled thermo-mechanical process.
Numerical simulations are very much essential in order to obtain a
complete knowledge of the process as well as the physics underlying
it. In the present work a model based approach is adopted in order to
study material flow. A thermo-mechanical based CFD model is
developed using a Finite Element package, Comsol Multiphysics.
The fluid flow analysis is done. The model simultaneously predicts
shear strain fields, shear strain rates and shear stress over the entire
workpiece for the given conditions. The flow fields generated by the
streamline plot give an idea of the material flow. The variation of
dynamic viscosity, velocity field and shear strain fields with various
welding parameters is studied. Finally the result obtained from the
above mentioned conditions is discussed elaborately and concluded.
Abstract: Waste load allocation (WLA) policies may use multiobjective
optimization methods to find the most appropriate and
sustainable solutions. These usually intend to simultaneously
minimize two criteria, total abatement costs (TC) and environmental
violations (EV). If other criteria, such as inequity, need for
minimization as well, it requires introducing more binary
optimizations through different scenarios. In order to reduce the
calculation steps, this study presents value index as an innovative
decision making approach. Since the value index contains both the
environmental violation and treatment costs, it can be maximized
simultaneously with the equity index. It implies that the definition of
different scenarios for environmental violations is no longer required.
Furthermore, the solution is not necessarily the point with minimized
total costs or environmental violations. This idea is testified for Haraz
River, in north of Iran. Here, the dissolved oxygen (DO) level of river
is simulated by Streeter-Phelps equation in MATLAB software. The
WLA is determined for fish farms using multi-objective particle
swarm optimization (MOPSO) in two scenarios. At first, the trade-off
curves of TC-EV and TC-Inequity are plotted separately as the
conventional approach. In the second, the Value-Equity curve is
derived. The comparative results show that the solutions are in a
similar range of inequity with lower total costs. This is due to the
freedom of environmental violation attained in value index. As a
result, the conventional approach can well be replaced by the value
index particularly for problems optimizing these objectives. This
reduces the process to achieve the best solutions and may find better
classification for scenario definition. It is also concluded that decision
makers are better to focus on value index and weighting its contents
to find the most sustainable alternatives based on their requirements.
Abstract: Channel sections are widely used in practice as beams.
However, design rules for eccentrically loaded (not through shear
center) beams with channel cross- sections are not available in
Eurocode 3. This paper compares the ultimate loads based on the
adjusted design rules for lateral torsional buckling of eccentrically
loaded channel beams in bending to the ultimate loads obtained with
Finite Element (FE) simulations on the basis of a parameter study.
Based on the proposed design rule, this study has led to a new design
rule which conforms to Eurocode 3.
Abstract: This paper analyses the heat transfer performance and
fluid flow using different nanofluids in a square enclosure. The
energy equation and Navier-Stokes equation are solved numerically
using finite volume scheme. The effect of volume fraction
concentration on the enhancement of heat transfer has been studied
icorporating the Brownian motion; the influence of effective thermal
conductivity on the enhancement was also investigated for a range of
volume fraction concentration. The velocity profile for different
Rayleigh number. Water-Cu, water AL2O3 and water-TiO2 were
tested.
Abstract: Fruit juices play important roles in human health as
being a key part of nutrition. Juice and nectar are two categories of
drinks with so many variations for consumers, regardless of age,
lifestyle and taste preferences, which they can find their favorites.
Juices contain 100% pulp when pulp content of ‘nectar’ changes
between 25%-50%. In this study, potassium (K), magnesium (Mg),
and phosphorus (P) contents in orange juice and nectar is determined
for conscious consumption. For this purpose inductively coupled
plasma optical emission spectrometry (ICP-OES) is used to find out
potassium (K), magnesium (Mg), and phosphorus (P) contents in
orange juices and nectar. Furthermore, the daily intake of elements
from orange juice and nectar that affects human health is also
investigated. From the results of experiments K, Mg and P contents
are found in orange juice as 1351; 73,25; 89,27 ppm and in orange
nectar as 986; 33,76; 51,30 respectively.
Abstract: This work studied the isomerization of 1-butene over
hydrotalcite catalyst. The experiments were conducted at various gas
hourly space velocity (GHSV), reaction temperature and feed
concentration. No catalyst deactivation was observed over the
reaction time of 16 hours. Two major reaction products were trans-2-
butene and cis-2-butene. The reaction temperature played an
important role on the reaction selectivity. At high operating
temperatures, the selectivity of trans-2-butene was higher than the
selectivity of cis-2-butene while it was opposite at lower reaction
temperature. In the range of operating condition, the maximum
conversion of 1-butene was found at 74% when T = 673 K and GHSV
= 4 m3/h/kg-cat with trans- and cis-2-butene selectivities of 54% and
46%, respectively. Finally, the kinetic parameters of the reaction
were determined.
Abstract: Prosperity of electronic equipment in photocopying
environment not only has improved work efficiency, but also has
changed indoor air quality. Considering the number of photocopying
employed, indoor air quality might be worse than in general office
environments. Determining the contribution from any type of
equipment to indoor air pollution is a complex matter. Non-methane
hydrocarbons are known to have an important role on air quality due
to their high reactivity. The presence of hazardous pollutants in
indoor air has been detected in one photocopying shop in Novi Sad,
Serbia. Air samples were collected and analyzed for five days, during
8-hr working time in three time intervals, whereas three different
sampling points were determined. Using multiple linear regression
model and software package STATISTICA 10 the concentrations of
occupational hazards and microclimates parameters were mutually
correlated. Based on the obtained multiple coefficients of
determination (0.3751, 0.2389 and 0.1975), a weak positive
correlation between the observed variables was determined. Small
values of parameter F indicated that there was no statistically
significant difference between the concentration levels of nonmethane
hydrocarbons and microclimates parameters. The results
showed that variable could be presented by the general regression
model: y = b0 + b1xi1+ b2xi2. Obtained regression equations allow to
measure the quantitative agreement between the variables and thus
obtain more accurate knowledge of their mutual relations.
Abstract: Press-hardened profiles are used e.g. for automotive
applications in order to improve light weight construction due to the
high reachable strength. The application of interior water-air spray
cooling contributes to significantly reducing the cycle time in the
production of heat-treated tubes. This paper describes a new
manufacturing method for producing press-hardened hollow profiles
by means of an additional interior cooling based on a water-air spray.
Furthermore, this paper provides the results of thorough
investigations on the properties of press-hardened tubes in
dependence of varying spray parameters.
Abstract: In this study, we proposed two techniques to track the
maximum power point (MPPT) of a photovoltaic system. The first is
an intelligent control technique, and the second is robust used for
variable structure system. In fact the characteristics I-V and P–V of
the photovoltaic generator depends on the solar irradiance and
temperature. These climate changes cause the fluctuation of
maximum power point; a maximum power point tracking technique
(MPPT) is required to maximize the output power. For this we have
adopted a control by fuzzy logic (FLC) famous for its stability and
robustness. And a Siding Mode Control (SMC) widely used for
variable structure system. The system comprises a photovoltaic panel
(PV), a DC-DC converter, which is considered as an adaptation stage
between the PV and the load. The modelling and simulation of the
system is developed using MATLAB/Simulink. SMC technique
provides a good tracking speed in fast changing irradiation and when
the irradiation changes slowly or it is constant the panel power of
FLC technique presents a much smoother signal with less
fluctuations.
Abstract: In this work, two fermentations at different
temperatures (25 and 30ºC), with cell recycling, were accomplished
to produce ethanol, using a mix of commercial substrates, xylose
(70%) and glucose (30%), as organic source for Scheffersomyces
stipitis. Five consecutive fermentations of 80 g L-1 (1º, 2º and 3º
recycles), 96 g L-1 (4º recycle) and 120 g L-1 (5º recycle)reduced
sugars led to a final maximum ethanol concentration of 17.2 and 34.5
g L-1, at 25 and 30ºC, respectively. Glucose was the preferred
substrate; moreover xylose startup degradation was initiated after a
remaining glucose presence in the medium. Results showed that yeast
acid treatment, performed before each cycle, provided improvements
on cell viability, accompanied by ethanol productivity of 2.16 g L-1 h-
1 at 30ºC. A maximum 36% of xylose was retained in the
fermentation medium and after five-cycle fermentation an ethanol
yield of 0.43 g ethanol/g sugars was observed. S. stipitis fermentation
capacity and tolerance showed better results at 30ºC with 83.4% of
theoretical yield referenced on initial biomass.
Abstract: Structural Equation Modeling (SEM) was used to test
a hypothesized model explaining Malaysian hypermarket customers’
perceptions of brand trust (BT), customer perceived value (CPV) and
perceived service quality (PSQ) on building their brand loyalty
(CBL) and generating positive word-of-mouth communication
(WOM). Self-administered questionnaires were used to collect data
from 374 Malaysian hypermarket customers from Mydin, Tesco,
Aeon Big and Giant in Kuala Lumpur, a metropolitan city of
Malaysia. The data strongly supported the model exhibiting that BT,
CPV and PSQ are prerequisite factors in building customer brand
loyalty, while PSQ has the strongest effect on prediction of customer
brand loyalty compared to other factors. Besides, the present study
suggests the effect of the aforementioned factors via customer brand
loyalty strongly contributes to generate positive word of mouth
communication.
Abstract: In this research numerical simulations are performed,
using the multi-relaxation-time lattice Boltzmann method, in the
range 3 ≤ β = w[d] ≤ 30 at Re = 100, 200 and 300, where β the
blockage ratio, w is the equispaced distance between centers of
cylinders, d is the diameter of the cylinder and Re is the Reynolds
number, respectively. Special attention is paid to the effect of the
equispaced distance between centers of cylinders. Visualization of
the vorticity contour visualization are presented for some simulation
showing the flow dynamics and patterns for blockage effect. Results
show that the drag and mean drag coefficients, and Strouhal number,
in general, decrease with the increase of β for fixed Re. It is found
that the decreasing rate of drag and mean drag coefficients and
Strouhal number is more distinct in the range 3 ≤ β ≤ 15. We found
that when β > 15, the blockage effect almost diminishes. Our results
further indicate that the drag and mean drag coefficients, peak value
of the lift coefficient, root-mean-square value of the lift and drag
coefficients and the ratio between lift and drag coefficients decrease
with the increase of Re. The results indicate that symmetry boundary
condition have more blockage effect as compared to periodic
boundary condition.
Abstract: This study investigates the use of a time-series of
MODIS NDVI data to identify agricultural land cover change on an
annual time step (2007 - 2012) and characterize the trend. Following
an ISODATA classification of the MODIS imagery to selectively
mask areas not agriculture or semi-natural, NDVI signatures were
created to identify areas cereals and vineyards with the aid of
ancillary, pictometry and field sample data for 2010. The NDVI
signature curve and training samples were used to create a decision
tree model in WEKA 3.6.9 using decision tree classifier (J48)
algorithm; Model 1 including ISODATA classification and Model 2
not. These two models were then used to classify all data for the
study area for 2010, producing land cover maps with classification
accuracies of 77% and 80% for Model 1 and 2 respectively. Model 2
was subsequently used to create land cover classification and change
detection maps for all other years. Subtle changes and areas of
consistency (unchanged) were observed in the agricultural classes
and crop practices. Over the years as predicted by the land cover
classification. Forty one percent of the catchment comprised of
cereals with 35% possibly following a crop rotation system.
Vineyards largely remained constant with only one percent
conversion to vineyard from other land cover classes.
Abstract: This paper investigates the benefits of deliberately
unbalancing both operation time means (MTs) and unreliability
(failure and repair rates) for non-automated production lines. The
lines were simulated with various line lengths, buffer capacities,
degrees of imbalance and patterns of MT and unreliability imbalance.
Data on two performance measures, namely throughput (TR) and
average buffer level (ABL) were gathered, analyzed and compared to
a balanced line counterpart. A number of conclusions were made
with respect to the ranking of configurations, as well as to the
relationships among the independent design parameters and the
dependent variables. It was found that the best configurations are a
balanced line arrangement and a monotone decreasing MT order,
coupled with either a decreasing or a bowl unreliability configuration,
with the first generally resulting in a reduced TR and the second
leading to a lower ABL than those of a balanced line.