Abstract: The effect of transition metal doping on Pt/Al2O3
catalyst used in propane dehydrogenation reaction at 500°C was
studied. The preparation methods investigated were sequential
impregnation (Pt followed by the 2nd metal or the 2nd metal followed
by Pt) and co-impregnation. The metal contents of these catalysts
were fixed as the weight ratio of Pt per the 2nd metal of around 0.075.
These catalysts were characterized by N2-physisorption, TPR, COchemisorption
and NH3-TPD. It was found that the impregnated 2nd
metal had an effect upon reducibility of Pt due to its interaction with
transition metal-containing structure. This was in agreement with the
CO-chemisorption result that the presence of Pt metal, which is a
result from Pt species reduction, was decreased. The total acidity of
bimetallic catalysts is decreased but the strong acidity is slightly
increased. It was found that the stability of bimetallic catalysts
prepared by co-impregnation and sequential impregnation where the
2nd metal was impregnated before Pt were better than that of
monometallic catalyst (undoped Pt one) due to the forming of Pt sites
located on the transition metal-oxide modified surface. Among all
preparation methods, the sequential impregnation method- having Pt
impregnated before the 2nd metal gave the worst stability because this
catalyst lacked the modified Pt sites and some fraction of Pt sites was
covered by the 2nd metal.
Abstract: The formulated problem of optimization of the
technological process of water treatment for thermal power plants is
considered in this article. The problem is of multiparametric nature.
To optimize the process, namely, reduce the amount of waste water, a
new technology was developed to reuse such water. A mathematical
model of the technology of wastewater reuse was developed.
Optimization parameters were determined. The model consists of a
material balance equation, an equation describing the kinetics of ion
exchange for the non-equilibrium case and an equation for the ion
exchange isotherm. The material balance equation includes a
nonlinear term that depends on the kinetics of ion exchange. A direct
problem of calculating the impurity concentration at the outlet of the
water treatment plant was numerically solved. The direct problem
was approximated by an implicit point-to-point computation
difference scheme. The inverse problem was formulated as relates to
determination of the parameters of the mathematical model of the
water treatment plant operating in non-equilibrium conditions. The
formulated inverse problem was solved. Following the results of
calculation the time of start of the filter regeneration process was
determined, as well as the period of regeneration process and the
amount of regeneration and wash water. Multi-parameter
optimization of water treatment process for thermal power plants
allowed decreasing the amount of wastewater by 15%.
Abstract: Considering palm oil as non-drying oil owing to its
low iodine value, an attempt was taken to increase the unsaturation in
the fatty acid chains of palm oil for the preparation of alkyds. To
increase the unsaturation in the palm oil, sulphuric acid (SA) and
para-toluene sulphonic acid (PTSA) was used prior to alcoholysis for
the dehydration process. The iodine number of the oil samples was
checked for the unsaturation measurement by Wijs method. Alkyd
resin was prepared using the dehydrated palm oil by following
alcoholysis and esterification reaction. To improve the film properties
0.5wt.% multi-wall carbon nano tubes (MWCNTs) were used to
manufacture polymeric film. The properties of the resins were
characterized by various physico-chemical properties such as density,
viscosity, iodine value, saponification value, etc. Structural
elucidation was confirmed by Fourier transform of infrared
spectroscopy and proton nuclear magnetic resonance; surfaces of the
films were examined by field-emission scanning electron microscope.
In addition, pencil hardness and chemical resistivity was also
measured by using standard methods. The effect of enhancement of
the unsaturation in the fatty acid chain found significant and
motivational. The resin prepared with dehydrated palm oil showed
improved properties regarding hardness and chemical resistivity
testing. The incorporation of MWCNTs enhanced the thermal
stability and hardness of the films as well.
Abstract: Data mining idea is mounting rapidly in admiration
and also in their popularity. The foremost aspire of data mining
method is to extract data from a huge data set into several forms that
could be comprehended for additional use. The data mining is a
technology that contains with rich potential resources which could be
supportive for industries and businesses that pay attention to collect
the necessary information of the data to discover their customer’s
performances. For extracting data there are several methods are
available such as Classification, Clustering, Association,
Discovering, and Visualization… etc., which has its individual and
diverse algorithms towards the effort to fit an appropriate model to
the data. STATISTICA mostly deals with excessive groups of data
that imposes vast rigorous computational constraints. These results
trials challenge cause the emergence of powerful STATISTICA Data
Mining technologies. In this survey an overview of the STATISTICA
software is illustrated along with their significant features.
Abstract: Properties of Portland cement mixtures with various
fractions of metakaolin were studied. 10% of Portland cement CEM I
42.5 R was replaced by different fractions of high reactivity
metakaolin with defined chemical and mineralogical properties.
Various fractions of metakaolin were prepared by jet mill classifying
system. There is a clear trend between fineness of metakaolin and
hydration heat development. Due to metakaolin presence in mixtures
the compressive strength development of mortars is rather slower for
coarser fractions but 28-day flexural strengths are improved for all
fractions of metakaoline used in mixtures compared to reference
sample of pure Portland cement. Yield point, plastic viscosity and
adhesion of fresh pastes are considerably influenced by fineness of
metakaolin used in cement pastes.
Abstract: Electronic Word-Of-Mouth (eWOM) communities
represent today an important source of information in which more
and more customers base their purchasing decisions. They include
thousands of reviews concerning very different products and services
posted by many individuals geographically distributed all over the
world. Due to their massive audience, eWOM communities can help
users to find the product they are looking for even if they are less
popular or rare. This is known as the long tail effect, which leads to a
larger number of lower-selling niche products. This paper analyzes
the long tail effect in a well-known eWOM community and defines a
tool for finding niche products unavailable through conventional
channels.
Abstract: The heavy metal pollution degree in the soils around
the Zangezur copper and molybdenum combine in Syunik Marz,
Armenia was assessed. The results of the study showed that heavy
metal pollution degree in the soils mainly decreased with increasing
distance from the open mine and the ore enrichment combine which
indicated that the open mine and the ore enrichment combine were
the main sources of heavy metal pollution. The only exception was
observed in the northern part of the open mine where pollution
degree in the sites (along the open mine) situated 600 meters far from
the mine was higher than that in the sites located 300 meters far from
the mine. This can be explained by the characteristics of relief and air
currents as well as the weak vegetation cover of these sites and the
characteristics of soil structure. According to geo-accumulation index
(I-geo), contamination factor (Cf), contamination degree (Cd) and
pollution load index (PLI) values, the pollution degree in the soils
around the open mine and the ore enrichment combine was higher
than that in the soils around the tailing dumps which was due to the
proper and accurate operation of the Artsvanik tailing damp and the
recultivation of the Voghji tailing dump.
The high Cu and Mo pollution of the soils was conditioned by the
character of industrial activities, the moving direction of air currents
as well as the physicochemical peculiarities of the soils.
Abstract: Catalytic combustion of methane is imperative due to
stability of methane at low temperature. Methane (CH4), therefore,
remains unconverted in vehicle exhausts thereby causing greenhouse
gas GHG emission problem. In this study, heterogeneous catalysts of
palladium with bio-char (2 wt% Pd/Bc) and Al2O3 (2wt% Pd/ Al2O3)
supports were prepared by incipient wetness impregnation and then
subsequently tested for catalytic combustion of CH4. Support-porous
heterogeneous catalytic combustion (HCC) material were selected
based on factors such as surface area, porosity, thermal stability,
thermal conductivity, reactivity with reactants or products, chemical
stability, catalytic activity, and catalyst life. Sustainable and
renewable support-material of bio-mass char derived from palm shell
waste material was compared with those from the conventional
support-porous materials. Kinetic rate of reaction was determined for
combustion of methane on Palladium (Pd) based catalyst with Al2O3
support and bio-char (Bc). Material characterization was done using
TGA, SEM, and BET surface area. The performance test was
accomplished using tubular quartz reactor with gas mixture ratio of
3% methane and 97% air. The methane porous-HCC conversion was
carried out using online gas analyzer connected to the reactor that
performed porous-HCC. BET surface area for prepared 2 wt% Pd/Bc
is smaller than prepared 2wt% Pd/ Al2O3 due to its low porosity
between particles. The order of catalyst activity based on kinetic rate
on reaction of catalysts in low temperature was 2wt%
Pd/Bc>calcined 2wt% Pd/ Al2O3> 2wt% Pd/ Al2O3>calcined 2wt%
Pd/Bc. Hence agro waste material can successfully be utilized as an
inexpensive catalyst support material for enhanced CH4 catalytic
combustion.
Abstract: The capability of CNC gantry milling machines in
manufacturing long components has caused the expanded use of such
machines. On the other hand, the machines’ gantry rigidity can
reduce under severe loads or vibration during operation. Indeed, the
quality of machining is dependent on the machine’s dynamic
behavior throughout the operating process. For this reason, these
types of machines have always been used widely and are not
efficient. Therefore, they can usually be employed for rough
machining and may not produce adequate surface finishing. In this
paper, a CNC gantry milling machine with the potential to produce
good surface finish has been designed and analyzed. The lowest
natural frequency of this machine is 202 Hz corresponding to 12000
rpm at all motion amplitudes with a full range of suitable frequency
responses. Meanwhile, the maximum deformation under dead loads
for the gantry machine is 0.565*m, indicating that this machine tool
is capable of producing higher product quality.
Abstract: Power Regeneration in Refrigeration Plant concept
has been analyzed and has been shown to be capable of saving about
25% power in Cryogenic Plants with the Power Regeneration System
(PRS) running under nominal conditions. The innovative component
Compressor Expander Group (CEG) based on turbomachinery has
been designed and built modifying CETT compressor and expander,
both selected for optimum plant performance. Experiments have
shown the good response of the turbomachines to run with R404a as
working fluid. Power saving up to 12% under PRS derated conditions
(50% loading) has been demonstrated. Such experiments allowed
predicting a power saving up to 25% under CEG full load.
Abstract: Advances in the use of health care technology have
resulted in increased adverse events (AEs) related to the use of
medical devices. The study focused on the existing reporting systems.
This study was conducted in a tertiary care public sector hospital.
Devices included Syringe infusion pumps, Cardiac monitors, Pulse
oximeters, Ventilators and Defibrillators. A total of 211 respondents
were recruited. Interviews were held with 30 key informants. Medical
records were scrutinized. Relevant statistical tests were used.
Resident doctors reported maximum frequency of AEs, followed
by nurses; and least by consultants. A significant association was
found between the cadre of health care personnel and awareness that
the patients and bystanders have a risk of sustaining AE. Awareness
regarding reporting of AEs was low, and it was generally done
verbally. Other critical findings are discussed in the light of the
barriers to reporting, reasons for non-compliance, recording system,
and so on.
Abstract: This paper discusses the design and analysis of a
hybrid PV-Fuel cell energy system destined to power a DC load. The
system is composed of a photovoltaic array, a fuel cell, an
electrolyzer and a hydrogen tank. HOMER software is used in this
study to calculate the optimum capacities of the power system
components that their combination allows an efficient use of solar
resource to cover the hourly load needs. The optimal system sizing
allows establishing the right balance between the daily electrical
energy produced by the power system and the daily electrical energy
consumed by the DC load using a 28 KW PV array, a 7.5 KW fuel
cell, a 40KW electrolyzer and a 270 Kg hydrogen tank. The variation
of powers involved into the DC bus of the hybrid PV-fuel cell system
has been computed and analyzed for each hour over one year: the
output powers of the PV array and the fuel cell, the input power of
the elctrolyzer system and the DC primary load. Equally, the annual
variation of stored hydrogen produced by the electrolyzer has been
assessed. The PV array contributes in the power system with 82%
whereas the fuel cell produces 18%. 38% of the total energy
consumption belongs to the DC primary load while the rest goes to
the electrolyzer.
Abstract: Comparing other methods of waste water treatment,
constructed wetlands are one of the most fascinating practices
because being a natural process they are eco-friendly have low
construction and maintenance cost and have considerable capability
of wastewater treatment. The current research was focused mainly on
comparison of Ranunculus muricatus and Typha latifolia as wetland
plants for domestic wastewater treatment by designing and
constructing efficient pilot scale horizontal subsurface flow
mesocosms. Parameters like chemical oxygen demand, biological
oxygen demand, phosphates, sulphates, nitrites, nitrates, and
pathogenic indicator microbes were studied continuously with
successive treatments. Treatment efficiency of the system increases
with passage of time and with increase in temperature. Efficiency of
T. latifolia planted setups in open environment was fairly good for
parameters like COD and BOD5 which was showing reduction up to
82.5% for COD and 82.6% for BOD5 while DO was increased up to
125%. Efficiency of R. muricatus vegetated setup was also good but
lowers than that of T. latifolia planted showing 80.95% removal of
COD and BOD5. Ranunculus muricatus was found effective in
reducing bacterial count in wastewater. Both macrophytes were
found promising in wastewater treatment.
Abstract: Enterococci are important inhabitants of the animal
intestine and are widely used in probiotic products. A probiotic strain
is expected to possess several desirable properties in order to exert
beneficial effects. Therefore, the objective of this study was to
isolate, characterize and identify Enterococcus sp. from chicken cecal
and fecal samples to determine potential probiotic properties.
Enterococci were isolated from chicken ceca and feces of thirty three
clinically healthy chickens from a local farm. In vitro studies were
performed to assess antibacterial activity of the isolated LAB (using
agar well diffusion and cell free supernatant broth technique against
Salmonella enterica serotype Enteritidis), survival in acidic
conditions, resistance to bile salts, and their survival during simulated
gastric juice conditions at pH 2.5. Isolates were identified by
biochemical carbohydrate fermentation patterns using an API 50
CHL kit and API ZYM kits and by sequenced 16S rDNA. An isolate
belonging to E. faecium species exhibited inhibitory effect against S.
enteritidis. This isolate producing a clear zone as large as 10.30 mm
or greater and was able to grow in the coculture medium and at the
same time, inhibited the growth S. enteritidis. In addition, E. faecium
exhibited significant resistance under highly acidic conditions at pH
2.5 for 8 h and survived well in bile salt at 0.2% for 24 h and showing
ability to survive in the presence of simulated gastric juice at pH 2.5.
Based on these results, E. faecium isolate fulfills some of the criteria
to be considered as a probiotic strain and therefore, could be used as a
feed additive with good potential for controlling S. Enteritidis in
chickens. However, in vivo studies are needed to determine the safety
of the strain.
Abstract: This work deals with parameter identification of
permanent magnet motors, a class of ac motor which is particularly
important in industrial automation due to characteristics like
applications high performance, are very attractive for applications
with limited space and reducing the need to eliminate because they
have reduced size and volume and can operate in a wide speed range,
without independent ventilation. By using experimental data and
genetic algorithm we have been able to extract values for both the
motor inductance and the electromechanical coupling constant, which
are then compared to measured and/or expected values.
Abstract: In this paper, the problem of fault detection and
isolation in the attitude control subsystem of spacecraft formation
flying is considered. In order to design the fault detection method, an
extended Kalman filter is utilized which is a nonlinear stochastic state
estimation method. Three fault detection architectures, namely,
centralized, decentralized, and semi-decentralized are designed based
on the extended Kalman filters. Moreover, the residual generation
and threshold selection techniques are proposed for these
architectures.
Abstract: This research has been conducted to study the method
of culture and comparing growth and biomass of Gracilaria corticata
cultured on rope and net for 50 days through two treatments (first
treatment: culture of alga on net and the second treatment: culture of
alga on rope and each treatment was repeated by four cases). During
culture period, the water of aquariums was replaced once every two
days for 40-50%. Also, 0.3-0.5 grams of urea fertilizer was added to
the culture environment for fertilization. Moreover, some of the
environmental factors such as pH, salinity and temperature of the
environment were measured on a daily basis. During the culture
period, extent of longitudinal growth of the species of both treatments
was equal. The said length was reached from 8-10 cm to 10.5-13 cm
accordingly. The resulted weight in repetitions of the first treatment
was higher than that of the second treatment in such a way as in the
first treatment, its weight reached from 10 grams to 21.119 grams and
in the second treatment, its weight reached from 10 grams to 17.663
grams. On a whole, it may be stated that that kind of alga being
studied has a considerable growth with respect to its volume. The
results have revealed that the percentage of daily growth and wet
weight at the end of the first treatment was higher than that of the
second treatment and it was registered as 0.934, 6.072 and 811.432 in
the first treatment and 0.797, 4.990 and 758.071 in the second
treatment respectively. This difference is significant (P
Abstract: The concentrations of cadmium and lead in sewage
sludge samples were determined by Atomic Absorption
Spectrometric Method. Samples of sewage sludge were obtained
from three sewage treatment plants localised in Middle Region of
Libya (Misrata, Msallata and Tarhünah cities).
The results shows that, the mean levels of Cadmium for all regions
are ranges from 81 to 123.4 ppm and these values are higher than the
limitations for the international standard which are not registered
more than 50 ppm (dry weight) in USA, Egypt and the EU countries.
While, the lead concentrations are ranged from 8.0 to 189.2 ppm and
all values are within the standard limits which graduated between
(275–613) ppm.
Abstract: Skin aging is a slow multifactorial process influenced
by both internal as well as external factors. Ultra-violet radiations
(UV), diet, smoking and personal habits are the most common
environmental factors that affect skin aging. Fat contents and fibrous
proteins as collagen and elastin are core internal structural
components. The direct influence of UV on elastin integrity and
health is central on aging of skin especially by time. The deposition
of abnormal elastic material is a major marker in a photo-aged skin.
Searching for compounds that may protect against cutaneous photodamage
is exceedingly valued. Retinoids and alpha hydroxy acids
have been endorsed by some researchers as possible candidates for
protecting and or repairing the effect of UV damaged skin. For
consolidating a better system of anti- and protective effects of such
anti-aging agents, we evaluated the combinatory effects of various
dosages of lactic acid and retinol on the dermal fibroblast’s elastin
levels exposed to UV. The UV exposed cells showed significant
reduction in the elastin levels. A combination of drugs with a higher
concentration of lactic acid (30 -35 mM) and a lower concentration of
retinol (10-15mg/mL) showed to work better in maintaining elastin
concentration in UV exposed cells. We assume this preservation
could be the result of increased tropo-elastin gene expression
stimulated by retinol whereas lactic acid probably repaired the UV
irradiated damage by enhancing the amount and integrity of the
elastin fibers.
Abstract: Numerical studies were conducted using Lattice
Boltzmann Method (LBM) to study the natural convection in a square
cavity in the presence of roughness. An algorithm based on a single
relaxation time Bhatnagar-Gross-Krook (BGK) model of Lattice
Boltzmann Method (LBM) was developed. Roughness was
introduced on both the hot and cold walls in the form of sinusoidal
roughness elements. The study was conducted for a Newtonian fluid
of Prandtl number (Pr) 1.0. The range of Ra number was explored
from 10^3 to 10^6 in a laminar region. Thermal and hydrodynamic
behavior of fluid was analyzed using a differentially heated square
cavity with roughness elements present on both the hot and cold wall.
Neumann boundary conditions were introduced on horizontal walls
with vertical walls as isothermal. The roughness elements were at the
same boundary condition as corresponding walls. Computational
algorithm was validated against previous benchmark studies
performed with different numerical methods, and a good agreement
was found to exist. Results indicate that the maximum reduction in
the average heat transfer was 16.66 percent at Ra number 10^5.