Abstract: Research results and optimal parameters investigation
of laser cut and profiling of diamond and quartz substrates by
femtosecond laser pulses are presented. Profiles 10 μm in width, ~25
μm in depth and several millimeters long were made. Investigation of
boundaries quality has been carried out with the use of AFM
«Vecco». Possibility of technological formation of profiles and
micro-holes in diamond and quartz substrates with nanometer-scale
boundaries is shown. Experimental results of multilayer dielectric
cover treatment are also presented. Possibility of precise upper layer
(thickness of 70–140 nm) removal is demonstrated. Processes of thin
metal film (60 nm and 350 nm thick) treatment are considered.
Isolation tracks (conductance ~ 10-11 S) 1.6–2.5 μm in width in
conductive metal layers are formed.
Abstract: The National Blood Center, Thai Red Cross Society is
responsible for providing blood to hospitals all over the country.
When any hospital needs blood, it will have to send the vehicle to
pick up at the NBC. There are a lot of vehicles to pick up blood at the
NBC every day. Each vehicle is usually empty for inbound trip and a
little loaded for outbound. The NBC realized such waste or loss and
there have been the third party offered to distribute blood and charge
for fee. This paper proposes to apply the vehicle routing problem
(VRP) for estimating the fair price. The idea is tested with the real
data during seven-day period of 6 – 12 July 2010 to estimate the fair
price for transporting blood in Bangkok Metropolitan Region.
Abstract: This paper presents the experimental results of silicone rubber housing material for 24kV lightning arrester under artificial accelerated ageing test based on IEC 61109 specifications. Specimens having inclined and alternated shed made of HTV silicone rubber with ATH content and having leakage distance 625 mm were tested continuously 1000 hrs in artificial salt fog chamber. After 1000 hrs of salt fog ageing test, obviously surface erosion was observed on trunk between the upper large shed and the lower small shed near the energized end. Decreasing in hydrophobicity and increasing in hardness were measured on tested specimen comparing with new specimen. Chemical analysis by ATR-FTIR confirmed the observation results.
Abstract: The mechanism behind the electromigration and
thermomigration failure in flip-chip solder joints with Cu-pillar bumps
was investigated in this paper through using finite element method.
Hot spot and the current crowding occurrs in the upper corner of
copper column instead of solders of the common solder ball. The
simulation results show that the change in thermal gradient is
noticeable, which might greatly affect the reliability of solder joints
with Cu-pillar bumps under current stressing. When the average
applied current density is increased from 1×104 A/cm2 to 3×104 A/cm2
in solders, the thermal gradient would increase from 74 K/cm to 901
K/cm at an ambient temperature of 25°C. The force from thermal
gradient of 901 K/cm can nearly induce thermomigration by itself.
With the increase in applied current, the thermal gradient is growing. It
is proposed that thermomigration likely causes a serious reliability
issue for Cu column based interconnects.
Abstract: In this survey the process of crack propagation at the
toe of concrete gravity dam is investigated by applying principals
and criteria of linear elastic fracture mechanic. Simulating process of
earthquake conditions for three models of dam with different
geometrical condition, in empty reservoir under plain stress is
calculated through special fracture mechanic software FRANNC2D
[1] for determining fracture mechanic criteria. The outcomes showed
that in spite of the primary expectations, the simultaneous existence
of fillet in both toe and heel area (model 3), the rate of maximum
principal stress has not been decreased; however, even the maximum
principal stress has increased, so it caused stress intensity factors
increase which is undesirable. On the other hand, the dam with heel
fillet has shown the best attitude and it is because of items like
decreasing the rates of maximum and minimum principal stresses and
also is related to decreasing the rates of stress intensity factors for 1st
& 2nd modes of the model.
Abstract: This paper presents data annotation models at five levels of granularity (database, relation, column, tuple, and cell) of relational data to address the problem of unsuitability of most relational databases to express annotations. These models do not require any structural and schematic changes to the underlying database. These models are also flexible, extensible, customizable, database-neutral, and platform-independent. This paper also presents an SQL-like query language, named Annotation Query Language (AnQL), to query annotation documents. AnQL is simple to understand and exploits the already-existent wide knowledge and skill set of SQL.
Abstract: The voice signal in Voice over Internet protocol (VoIP) system is processed through the best effort policy based IP network, which leads to the network degradations including delay, packet loss jitter. The work in this paper presents the implementation of finite impulse response (FIR) filter for voice quality improvement in the VoIP system through distributed arithmetic (DA) algorithm. The VoIP simulations are conducted with AMR-NB 6.70 kbps and G.729a speech coders at different packet loss rates and the performance of the enhanced VoIP signal is evaluated using the perceptual evaluation of speech quality (PESQ) measurement for narrowband signal. The results show reduction in the computational complexity in the system and significant improvement in the quality of the VoIP voice signal.
Abstract: This study describes the preparation of a novel proton
conducting membranes based on bacterial cellulose (BC) modified by
grafting of 2-acrylamido-2-methyl-1 -propanesulfonic acid (AMPS)
through UV-induced graft polymerization. These AMPS-g-BC
membranes have been characterized by various techniques including
FTIR, SEM and TGA, to find their successful grafting of AMPS on
BC, surface morphology and thermal stability, respectively. Physical
properties of AMPS-g-BC membranes have been assessed in terms of
Lamda value( λ ), ion exchange capacity(IEC) and proton
conductivity. The relationship between degree of grafting and AMPS
concentration used for grafting has been determined by weight gain
method. An optimum proton conductivity equal to 2.89x10-2 S cm-1
and IEC value equal to 1.79 mmol g-1 have been obtained when 20
wt% AMPS concentration is used for grafting (i.e. the corresponding
membrane is notated as AMPS20-g-BC).
Abstract: Due to insufficient frequency band and tremendous growth of the mobile users, complex computation is needed for the use of resources. Long distance communication began with the introduction of telegraphs and simple coded pulses, which were used to transmit short messages. Since then numerous advances have rendered reliable transfer of information both easier and quicker. Wireless network refers to any type of computer network that is wireless, and is commonly associated with a telecommunications network whose interconnections between nodes is implemented without the use of wires. Wireless network can be broadly categorized in infrastructure network and infrastructure less network. Infrastructure network is one in which we have a base station to serve the mobile users and in the infrastructure less network is one in which no infrastructure is available to serve the mobile users this kind of networks are also known as mobile Adhoc networks. In this paper we have simulated the result for different scenarios with protocols like AODV and DSR; we simulated the result for throughput, delay and receiving traffic in the given scenario.
Abstract: The three-dimensional incompressible flow past a
rectangular open cavity is investigated, where the aspect ratio of the
cavity is considered as 4. The principle objective is to use large-eddy
simulation to resolve and control the large-scale structures, which are
largely responsible for flow oscillations in a cavity. The flow past an
open cavity is very common in aerospace applications and can be a
cause of acoustic source due to hydrodynamic instability of the shear
layer and its interactions with the downstream edge. The unsteady
Navier-stokes equations have been solved on a staggered mesh using
a symmetry-preserving central difference scheme. Synthetic jet has
been used as an active control to suppress the cavity oscillations in
wake mode for a Reynolds number of ReD = 3360. The effect of
synthetic jet has been studied by varying the jet amplitude and
frequency, which is placed at the upstream wall of the cavity. The
study indicates that there exits a frequency band, which is larger than
a critical value, is effective in attenuating cavity oscillations when
blowing ratio is more than 1.0.
Abstract: This paper proposes an implementation for the
directed diffusion paradigm aids in studying this paradigm-s
operations and evaluates its behavior according to this
implementation. The directed diffusion is evaluated with respect to
the loss percentage, lifetime, end-to-end delay, and throughput.
From these evaluations some suggestions and modifications are
proposed to improve the directed diffusion behavior according to
this implementation with respect to these metrics. The proposed
modifications reflect the effect of local path repair by introducing a
technique called Loop-free Local Path Repair (LLPR) which
improves the directed diffusion behavior especially with respect to
packet loss percentage by about 92.69%. Also LLPR improves the
throughput and end-to-end delay by about 55.31% and 14.06%
respectively, while the lifetime decreases by about 29.79%.
Abstract: Multi-level voltage source inverters offer several
advantages such as; derivation of a refined output voltage with
reduced total harmonic distortion (THD), reduction of voltage ratings
of the power semiconductor switching devices and also the reduced
electro-magnetic-interference problems etc. In this paper, new
carrier-overlapped phase-disposition or sub-harmonic sinusoidal
pulse width modulation (CO-PD-SPWM) and also the carrieroverlapped
phase-disposition space vector modulation (CO-PDSVPWM)
schemes for a six-level diode-clamped inverter topology
are proposed. The principle of the proposed PWM schemes is similar
to the conventional PD-PWM with a little deviation from it in the
sense that the triangular carriers are all overlapped. The overlapping
of the triangular carriers on one hand results in an increased number
of switchings, on the other hand this facilitates an improved spectral
performance of the output voltage. It is demonstrated through
simulation studies that the six-level diode-clamped inverter with the
use of CO-PD-SPWM and CO-PD-SVPWM proposed in this paper is
capable of generating multiple levels in its output voltage. The
advantages of the proposed PWM schemes can be derived to benefit,
especially at lower modulation indices of the inverter and hence this
aspect of the proposed PWM schemes can be well exploited in high
power applications requiring low speeds of operation of the drive.
Abstract: The parametrical study of Shrouded Contra-rotating
Rotor was done in this paper based on 2D axisymmetric simulations.
The calculations were made with an actuator disk as double rotor
model. It objects to explore and quantify the effects of different shroud
geometry parameters mainly using the performance of power loading
(PL), which could evaluate the whole propulsion system capability as
5 Newtontotal thrust generationfor hover demand. The numerical
results show that:The increase of nozzle radius is desired but limited
by the flow separation, its optimal design is around 1.15 times rotor
radius, the viscosity effects greatly constraint the influence of nozzle
shape, the divergent angle around 10.5° performs best for chosen
nozzle length;The parameters of inlet such as leading edge curvature,
radius and internal shape do not affect thrust great but play an
important role in pressure distribution which could produce most part
of shroud thrust, they should be chosen according to the reduction of
adverse pressure gradients to reduce the risk of boundary separation.
Abstract: One of the main challenges for one phase anaerobic digestion processes is the high concentration of NH4+ and PO4 3- ions
in the digested sludge supernatant. This project focuses on enhancing the removal of nutrients during the anaerobic digestion process through fixing both NH4+ and PO4 3- ions in the form of struvite (magnesium ammonium phosphate, MAP, MgNH4PO4.6H2O) within the anaerobic sludge. Batch anaerobic digestion tests showed that Mg2+ concentration in the range 279 – 812 mg/L had insignificant effect on CGP but incurred a slight increase in COD removal. The reactor that had soluble Mg2+:NH4+:PO43- at a molar ratio of 1.28:1:00:1:00 achieved the best performance enhancement of 8% increase in COD removal and 32% reduction in NH4+ in the reactor supernatant. Overall, the results show that there is a potential to optimise conventional anaerobic digestion such that supernatant lean in P and N, and sludge rich in nutrients are obtained.
Abstract: Optimal capacitor allocation in distribution systems
has been studied for a long times. It is an optimization problem
which has an objective to define the optimal sizes and locations of
capacitors to be installed. In this works, an overview of capacitor
placement problem in distribution systems is briefly introduced. The
objective functions and constraints of the problem are listed and the
methodologies for solving the problem are summarized.
Abstract: The Information and Communication Technologies
(ICTs), and the Wide World Web (WWW) have fundamentally
altered the practice of teaching and learning world wide. Many
universities, organizations, colleges and schools are trying to apply
the benefits of the emerging ICT. In the early nineties the term
learning object was introduced into the instructional technology
vernacular; the idea being that educational resources could be broken
into modular components for later combination by instructors,
learners, and eventually computes into larger structures that would
support learning [1]. However in many developing countries, the use
of ICT is still in its infancy stage and the concept of learning object
is quite new. This paper outlines the learning object design
considerations for developing countries depending on learning
environment.
Abstract: Xanthan gum is one of the major commercial
biopolymers. Due to its excellent rheological properties xanthan gum
is used in many applications, mainly in food industry. Commercial
production of xanthan gum uses glucose as the carbon substrate;
consequently the price of xanthan production is high. One of the
ways to decrease xanthan price, is using cheaper substrate like
agricultural wastes. Iran is one of the biggest date producer countries.
However approximately 50% of date production is wasted annually.
The goal of this study is to produce xanthan gum from waste date
using Xanthomonas campestris PTCC1473 by submerged
fermentation. In this study the effect of three variables including
phosphor and nitrogen amount and agitation rate in three levels using
response surface methodology (RSM) has been studied. Results
achieved from statistical analysis Design Expert 7.0.0 software
showed that xanthan increased with increasing level of phosphor.
Low level of nitrogen leaded to higher xanthan production. Xanthan
amount, increasing agitation had positive influence. The statistical
model identified the optimum conditions nitrogen amount=3.15g/l,
phosphor amount=5.03 g/l and agitation=394.8 rpm for xanthan. To
model validation, experiments in optimum conditions for xanthan
gum were carried out. The mean of result for xanthan was 6.72±0.26.
The result was closed to the predicted value by using RSM.
Abstract: With the explosive growth of information sources available on the World Wide Web, it has become increasingly difficult to identify the relevant pieces of information, since web pages are often cluttered with irrelevant content like advertisements, navigation-panels, copyright notices etc., surrounding the main content of the web page. Hence, tools for the mining of data regions, data records and data items need to be developed in order to provide value-added services. Currently available automatic techniques to mine data regions from web pages are still unsatisfactory because of their poor performance and tag-dependence. In this paper a novel method to extract data items from the web pages automatically is proposed. It comprises of two steps: (1) Identification and Extraction of the data regions based on visual clues information. (2) Identification of data records and extraction of data items from a data region. For step1, a novel and more effective method is proposed based on visual clues, which finds the data regions formed by all types of tags using visual clues. For step2 a more effective method namely, Extraction of Data Items from web Pages (EDIP), is adopted to mine data items. The EDIP technique is a list-based approach in which the list is a linear data structure. The proposed technique is able to mine the non-contiguous data records and can correctly identify data regions, irrespective of the type of tag in which it is bound. Our experimental results show that the proposed technique performs better than the existing techniques.
Abstract: Self-efficacy, self-reliance, and motivation were
examined in a quasi-experimental study with 178 sophomore
university students. Participants used an interactive cardiovascular
anatomy and physiology CD-ROM, and completed a 15-item
questionnaire. Reliability of the questionnaire was established using
Cronbach-s alpha. Post-tests and course grades were examined using
a t-test, demonstrating no significance. Results of an item-to-item
analysis of the questionnaire showed overall satisfaction with the
teaching methodology and varied results for self-efficacy, selfreliance,
and motivation. Kendall-s Tau was calculated for all items
in the questionnaire.
Abstract: To understand complex living system an effort has
made by mechanical engineers and dentists to deliver prompt
products and services to patients concerned about their aesthetic look.
Since two decades various bracket systems have designed involving
techniques like milling, injection molding which are technically not
flexible for the customized dental product development. The aim of
this paper to design, develop a customized system which is
economical and mainly emphasizes the expertise design and
integration of engineering and dental fields. A custom made selfadjustable
lingual bracket and customized implants are designed and
developed using computer aided design (CAD) and rapid prototyping
technology (RPT) to improve the smiles and to overcome the
difficulties associated with conventional ones. Lengthy orthodontic
treatment usually not accepted by the patients because the patient
compliance is lost. Patient-s compliance can be improved by
facilitating faster tooth movements by designing a localized dental
vibrator using advanced engineering principles.