Abstract: Reinforced Concrete (RC) structures strengthened
with fiber reinforced polymer (FRP) lack in thermal resistance under
elevated temperatures in the event of fire. This phenomenon led to
the lining of strengthened concrete with thin high performance
cementitious composites (THPCC) to protect the substrate against
elevated temperature. Elevated temperature effects on THPCC, based
on different cementitious materials have been studied in the past but
high-alumina cement (HAC)-based THPCC have not been well
characterized. This research study will focus on the THPCC based on
HAC replaced by 60%, 70%, 80% and 85% of ground granulated
blast furnace slag (GGBS). Samples were evaluated by the
measurement of their mechanical strength (28 & 56 days of curing)
after exposed to 400°C, 600°C and 28°C of room temperature for
comparison and corroborated by their microstructure study. Results
showed that among all mixtures, the mix containing only HAC
showed the highest compressive strength after exposed to 600°C as
compared to other mixtures. However, the tensile strength of THPCC
made of HAC and 60% GGBS content was comparable to the
THPCC with HAC only after exposed to 600°C. Field emission
scanning electron microscopy (FESEM) images of THPCC
accompanying Energy Dispersive X-ray (EDX) microanalysis
revealed that the microstructure deteriorated considerably after
exposure to elevated temperatures which led to the decrease in
mechanical strength.
Abstract: One of the best ways for achievement of conventional
vehicle changing to hybrid case is trustworthy simulation result and
using of driving realities. For this object, in this paper, at first sevendegree-
of-freedom dynamical model of vehicle will be shown. Then
by using of statically model of engine, gear box, clutch, differential,
electrical machine and battery, the hybrid automobile modeling will
be down and forward simulation of vehicle for pedals to wheels
power transformation will be obtained. Then by design of a fuzzy
controller and using the proper rule base, fuel economy and
regenerative braking will be marked. Finally a series of
MATLAB/SIMULINK simulation results will be proved the
effectiveness of proposed structure.
Abstract: One of the essential requirements for the human
beings is the house for living. This is necessary to make the place of
satisfaction for contemporary houses residents by attention to their
culture. In this article represented the relevant theoretical literature
on cultural symbols by use the architecture semiotic to construct the
houses as a better place for living. In fact, make a place for everyday
life with changing the house to the home is one of the most
challengeable subject for architects all around the world. The target
of this article is to find Cypriot houses cultural symbols that assist
architect to design and build contemporary houses, to make more
satisfaction for its residents according to Cypriot life style and their
culture. This paper is based on researching the effect of cultural
symbols on housing, would require various types of methods.
However, this study focuses on two methods, which are quantitative
and qualitative. The purpose of the case-specific study is to finding
the symbols that used in contemporary houses by attention to the
Cypriot cultural symbols in Famagusta houses.
Abstract: We report a computational study of the spreading
dynamics of a viral infection in a complex (scale-free) network. The
final epidemic size distribution (FESD) was found to be unimodal or
bimodal depending on the value of the basic reproductive
number R0 . The FESDs occurred on time-scales long enough for
intermediate-time epidemic size distributions (IESDs) to be important
for control measures. The usefulness of R0 for deciding on the
timeliness and intensity of control measures was found to be limited
by the multimodal nature of the IESDs and by its inability to inform
on the speed at which the infection spreads through the population. A
reduction of the transmission probability at the hubs of the scale-free
network decreased the occurrence of the larger-sized epidemic events
of the multimodal distributions. For effective epidemic control, an
early reduction in transmission at the index cell and its neighbors was
essential.
Abstract: Lately, an interest has grown greatly in the usages of
RFID in an un-presidential applications. It is shown in the adaptation
of major software companies such as Microsoft, IBM, and Oracle
the RFID capabilities in their major software products. For example
Microsoft SharePoints 2010 workflow is now fully compatible with
RFID platform. In addition, Microsoft BizTalk server is also capable
of all RFID sensors data acquisition. This will lead to applications
that required high bit rate, long range and a multimedia content in
nature. Higher frequencies of operation have been designated for
RFID tags, among them are the 2.45 and 5.8 GHz. The higher the
frequency means higher range, and higher bit rate, but the drawback
is the greater cost. In this paper we present a single layer, low
profile patch antenna operates at 5.8 GHz with pure resistive input
impedance of 50 and close to directive radiation. Also, we propose
a modification to the design in order to improve the operation band
width from 8.7 to 13.8
Abstract: In this study, the effects of machining parameters on
specific energy during surface grinding of 6061Al-SiC35P
composites are investigated. Vol% of SiC, feed and depth of cut were
chosen as process variables. The power needed for the calculation of
the specific energy is measured from the two watt meter method.
Experiments are conducted using standard RSM design called Central
composite design (CCD). A second order response surface model was
developed for specific energy. The results identify the significant
influence factors to minimize the specific energy. The confirmation
results demonstrate the practicability and effectiveness of the
proposed approach.
Abstract: This paper proposes an effective adaptation learning
algorithm based on artificial neural networks for speed control of an
induction motor assumed to operate in a high-performance drives
environment. The structure scheme consists of a neural network
controller and an algorithm for changing the NN weights in order that
the motor speed can accurately track of the reference command. This
paper also makes uses a very realistic and practical scheme to
estimate and adaptively learn the noise content in the speed load
torque characteristic of the motor. The availability of the proposed
controller is verified by through a laboratory implementation and
under computation simulations with Matlab-software. The process is
also tested for the tracking property using different types of reference
signals. The performance and robustness of the proposed control
scheme have evaluated under a variety of operating conditions of the
induction motor drives. The obtained results demonstrate the
effectiveness of the proposed control scheme system performances,
both in steady state error in speed and dynamic conditions, was found
to be excellent and those is not overshoot.
Abstract: This paper presents the solution of power economic dispatch (PED) problem of generating units with valve point effects and multiple fuel options using Self-Adaptive Differential Evolution (SDE) algorithm. The global optimal solution by mathematical approaches becomes difficult for the realistic PED problem in power systems. The Differential Evolution (DE) algorithm is found to be a powerful evolutionary algorithm for global optimization in many real problems. In this paper the key parameters of control in DE algorithm such as the crossover constant CR and weight applied to random differential F are self-adapted. The PED problem formulation takes into consideration of nonsmooth fuel cost function due to valve point effects and multi fuel options of generator. The proposed approach has been examined and tested with the numerical results of PED problems with thirteen-generation units including valve-point effects, ten-generation units with multiple fuel options neglecting valve-point effects and ten-generation units including valve-point effects and multiple fuel options. The test results are promising and show the effectiveness of proposed approach for solving PED problems.
Abstract: The main aim is to perform mutational analysis of CTLA4 gene Exon 1 in SLE patients. A total of 61 SLE patients fulfilling “American College of Rheumatology (ACR) criteria" and 61 controls were enrolled in this study. The region of CTLA4 gene exon 1 was amplified by using Step-down PCR technique. Extracted DNA of band 354 bp was sequenced to analyze mutations in the exon-1 of CTLA-4 gene. Further, protein sequences were identified from nucleotide sequences of CTLA4 Exon 1 by using Expasy software and through Blast P software it was found that CTLA4 protein sequences of Pakistani SLE patients were similar to that of Chinese SLE population. No variations were found after patients sequences were compared with that of the control sequence. Furthermore it was found that CTLA4 protein sequences of Pakistani SLE patients were similar to that of Chinese SLE population. Thus CTLA4 gene may not be responsible for an autoimmune disease SLE.
Abstract: In this paper a mixed method by combining an evolutionary and a conventional technique is proposed for reduction of Single Input Single Output (SISO) continuous systems into Reduced Order Model (ROM). In the conventional technique, the mixed advantages of Mihailov stability criterion and continued Fraction Expansions (CFE) technique is employed where the reduced denominator polynomial is derived using Mihailov stability criterion and the numerator is obtained by matching the quotients of the Cauer second form of Continued fraction expansions. Then, retaining the numerator polynomial, the denominator polynomial is recalculated by an evolutionary technique. In the evolutionary method, the recently proposed Differential Evolution (DE) optimization technique is employed. DE method is based on the minimization of the Integral Squared Error (ISE) between the transient responses of original higher order model and the reduced order model pertaining to a unit step input. The proposed method is illustrated through a numerical example and compared with ROM where both numerator and denominator polynomials are obtained by conventional method to show its superiority.
Abstract: New lead-free ferroelectric relaxor ceramics were
prepared by conventional solid-state synthesis in the BaTiO3-Bi2O3-
Y2O3 systems. Some of these ceramics present a ferroelectric relaxor
with transition temperature close to room temperature. These new
materials are very interesting for applications and can replace leadbased
ceramic to prevent the toxic pollutions during the preparation
state. In the other hand, the energy band diagram shows the
potentiality of these compounds for the solar energy conversion.
Thus, some compositions have been tested successfully for H2
production upon visible light. The best activity occurs in alkaline
media with a rate evolution of about 0.15 mL g-1 mn-1 and a quantum
yield of 1% under polychromatic light.
Abstract: This paper presents the analysis of duct design using
static and dynamic approaches. The static approach is used to find
out applicability between the design and material applied. The
material used in this paper is Thermoplastic Olefins (TPO). For the
dynamic approach, the focusing is only on the CFD simulations. The
fatigue life in this design and material applied also covered.
Abstract: The modeling of sound radiation is of fundamental importance for understanding the propagation of acoustic waves and, consequently, develop mechanisms for reducing acoustic noise. The propagation of acoustic waves, are involved in various phenomena such as radiation, absorption, transmission and reflection. The radiation is studied through the linear equation of the acoustic wave that is obtained through the equation for the Conservation of Momentum, equation of State and Continuity. From these equations, is the Helmholtz differential equation that describes the problem of acoustic radiation. In this paper we obtained the solution of the Helmholtz differential equation for an infinite cylinder in a pulsating through free and homogeneous. The analytical solution is implemented and the results are compared with the literature. A numerical formulation for this problem is obtained using the Boundary Element Method (BEM). This method has great power for solving certain acoustical problems in open field, compared to differential methods. BEM reduces the size of the problem, thereby simplifying the input data to be worked and reducing the computational time used.
Abstract: Bean common mosaic necrosis virus (BCMNV) is a
potyvirus with a worldwide distribution. This virus causes serious
economic losses in Iran in many leguminoses. During 20008,
samples were collected from soybeans fields in Tehran Province.
Four isolates (S1, S2 and S3) were inoculated on 15 species of
Cucurbitaceae, Chenopodiaceae, Solanacae and Leguminosae.
Chenopodium quinoa and C. amaranticolor.
Did not developed any symptoms.all isolates caused mosaic
symptoms on Phaseolus vulgaris cv. Red Kidney and P. vulgaris cv.
Bountiful. The molecular weights of coat protein using SDS-PAGE
and western blotting were estimated at 33 kDa. Reverse transcription
polymerase chain reaction (RT-PCR) was performed using one
primer pairs designed by L. XU et al. An approximately 920 bp
fragment was amplified with a specific primer.
Abstract: In this paper, two centrifugal model tests (case 1: raft
foundation, case 2: 2x2 piled raft foundation) were conducted in
order to evaluate the effect of ground subsidence on load sharing
among piles and raft and settlement of raft and piled raft
foundations. For each case, two conditions consisting of undrained
(without groundwater pumping) and drained (with groundwater
pumping) conditions were considered. Vertical loads were applied
to the models after the foundations were completely consolidated by
selfweight at 50g. The results show that load sharing by the piles in
piled raft foundation (piled load share) for drained condition
decreases faster than that for undrained condition. Settlement of
both raft and piled raft foundations for drained condition increases
more quickly than that for undrained condition. In addition, the
settlement of raft foundation increases more largely than the
settlement of piled raft foundation for drained condition.
Abstract: Ten lactating multiparous Holstein cows were used in
a cross-over design with two dietary treatments and 28-d periods
(with 14 d as an adaptation) to study the effect of restaurant fat on
milk production and composition. Each cow was offered 14.7 kg
DM /d of the basal concentrate diet based on barley and corn (crude
protein = 17.7%, neutral detergent fiber = 23.5%, and acid detergent
fiber = 5.8% of dry matter) with free access to alfalfa. Dietary
treatments were arranged as supplying each cow with 0 (CONTROL)
or 150 g/day (RF) of restaurant fat. Supplemental RF did not
significantly (P > 0.25) affect milk yield, composition, and
composition yields, except for milk fat contents. Milk fat contents
were depressed (P < 0.05) with supplemental RF. Our results indicate
that RF could depress milk fat without affecting milk yield and that
the depression in milk fat in response to RF precedes the depression
in milk yield.
Abstract: A personal estimate of a health risk may not
correspond to a scientific assessment of the health risk. Hence, there
is a need to investigate perceived health risks in the public. In this
study, a young, educated and healthy group of people from a tertiary
institute were questioned about their health concerns. Ethics
clearance was obtained and data was collected by means of a
questionnaire. 362 students participated in the study. Tobacco use,
heavy alcohol drinking, illicit drugs, unsafe sex and potential
carcinogens were perceived to be the five greatest threats to health in
this cohort. On the other hand natural health products,
unemployment, unmet contraceptive needs, family violence and
homelessness were felt to be the least perceived health risks.
Nutrition-related health risks as well as health risks due to physical
inactivity and obesity were not perceived as major health threats.
Such a study of health perceptions may guide health promotion
campaigns.
Abstract: In Mauritius, much emphasis is put on measures to
combat the high prevalence of non-communicable diseases (NCDs).
Health promotion campaigns for the adoption of healthy behaviors
and screening programs are done regularly by local authorities and
NCD surveys are carried out at intervals. However, the health
behaviors of the poor have not been investigated so far. This study
aims to give an insight on the perceptions of health status and
lifestyle health behaviors of poor people in Mauritius. A crosssectional
study among 83 persons benefiting from social aid in a
selected urban district was carried out. Results showed that 51.8% of
respondents perceived that they had good health status. 57.8% had no
known NCD whilst 25.3% had hypertension, followed by diabetes
(16.9%), asthma (9.6%) and heart disease (7.2%).They had low
smoking (10.8%) and alcohol consumption (6.0%) as well as high
physical activity prevalence (54.2%). These results were significantly
different from the NCD survey carried out in the general population.
Consumption of vegetables in the study was high. Overweight and
obesity trends were however similar to the NCD survey report 2009.
These findings contrast with other international studies showing poor
people having poor perceptions of health status and unhealthy
behavioral choices. Whether these positive health behaviors of poor
people in Mauritius arise out of choice or whether it is because the
alternative behavior is too costly remains to be investigated further.
Abstract: Pattern matching based on regular tree grammars have been widely used in many areas of computer science. In this paper, we propose a pattern matcher within the framework of code generation, based on a generic and a formalized approach. According to this approach, parsers for regular tree grammars are adapted to a general pattern matching solution, rather than adapting the pattern matching according to their parsing behavior. Hence, we first formalize the construction of the pattern matches respective to input trees drawn from a regular tree grammar in a form of the so-called match trees. Then, we adopt a recently developed generic parser and tightly couple its parsing behavior with such construction. In addition to its generality, the resulting pattern matcher is characterized by its soundness and efficient implementation. This is demonstrated by the proposed theory and by the derived algorithms for its implementation. A comparison with similar and well-known approaches, such as the ones based on tree automata and LR parsers, has shown that our pattern matcher can be applied to a broader class of grammars, and achieves better approximation of pattern matches in one pass. Furthermore, its use as a machine code selector is characterized by a minimized overhead, due to the balanced distribution of the cost computations into static ones, during parser generation time, and into dynamic ones, during parsing time.
Abstract: To support mobility in ATM networks, a number of
technical challenges need to be resolved. The impact of handoff
schemes in terms of service disruption, handoff latency, cost
implications and excess resources required during handoffs needs to
be addressed. In this paper, a one phase handoff and route
optimization solution using reserved PVCs between adjacent ATM
switches to reroute connections during inter-switch handoff is
studied. In the second phase, a distributed optimization process is
initiated to optimally reroute handoff connections. The main
objective is to find the optimal operating point at which to perform
optimization subject to cost constraint with the purpose of reducing
blocking probability of inter-switch handoff calls for delay tolerant
traffic. We examine the relation between the required bandwidth
resources and optimization rate. Also we calculate and study the
handoff blocking probability due to lack of bandwidth for resources
reserved to facilitate the rapid rerouting.