Abstract: This study was carried out experimentally and analytically about the performance of solar cell panel system for operating the pump coupled by dc-motor. The solar cell panel with total area 1.9848 m2 consists of three modules of 80 Wp each. The small centrifugal pump powered by dc-motor is operated to lift water from 1m to 7m heads in sequence and gives the amount of water pumped over the whole day from 08.00 to 16.00 h are 11988, 10851, 8874, 7695, 5760, 3600, 2340 L/d respectively. The hourly global solar radiation during the day is an average of 506 W/m2. This study also presents the I-V characteristics of the panel at global radiations 200, 400, 600, 800 and 1000 W/m2 matched with the operation of the pump at the above lifting heads. It proves that the only solar radiations 800 and 1000 W/m2 could provide lifting head from 1m to 7m. The analysis shows the best efficiency point of the performance of solar cell panel system occurs at the pumping head 2.89 m.
Abstract: This study examined the effects of two dynamic
visualizations on 60 Malaysian primary school student-s performance
(time on task), retention and transference. The independent variables
in this study were the two dynamic visualizations, the video and the
animated instructions. The dependent variables were the gain score of
performance, retention and transference. The results showed that the
students in the animation group significantly outperformed the
students in the video group in retention. There were no significant
differences in terms of gain scores in the performance and
transference among the animation and the video groups, although the
scores were slightly higher in the animation group compared to the
video group. The conclusion of this study is that the animation
visualization is superior compared to the video in the retention for a
procedural task.
Abstract: Global climate change has become the preeminent
threat to human security in the 21st century. From mitigation perspective, this study aims to evaluate the performance of biogas
renewable project under clean development mechanism activities
(namely Korat-Waste-to-Energy) in Thailand and to assess local perceptions towards the significance of climate change mitigation and
sustainability of such project in their community. Questionnaire was
developed based on the national sustainable development criteria and
was distributed among systematically selected households within
project boundaries (n=260). Majority of the respondents strongly agreed with the reduction of odor problems (81%) and air pollution
(76%). However, they were unsure about greenhouse gas reduction from such project and ignorant about the key issues of climate change. A lesson learned suggested that there is a need to further
investigate the possible socio-psychological barriers may significantly shape public perception and understandings of climate
change in the local context.
Abstract: The aim of this paper is to present the kinematic
analysis and mechanism design of an assistive robotic leg for
hemiplegic and hemiparetic patients. In this work, the priority is to
design and develop the lightweight, effective and single driver
mechanism on the basis of experimental hip and knee angles- data for
walking speed of 1 km/h. A mechanism of cam-follower with three
links is suggested for this purpose. The kinematic analysis is carried
out and analysed using commercialized MATLAB software based on
the prototype-s links sizes and kinematic relationships. In order to
verify the kinematic analysis of the prototype, kinematic analysis data
are compared with the experimental data. A good agreement between
them proves that the anthropomorphic design of the lower extremity
exoskeleton follows the human walking gait.
Abstract: The process of wafer fabrication is arguably the most
technologically complex and capital intensive stage in semiconductor
manufacturing. This large-scale discrete-event process is highly reentrant,
and involves hundreds of machines, restrictions, and
processing steps. Therefore, production control of wafer fabrication
facilities (fab), specifically scheduling, is one of the most challenging
problems that this industry faces. Dispatching rules have been
extensively applied to the scheduling problems in semiconductor
manufacturing. Moreover, lot release policies are commonly used in
this manufacturing setting to further improve the performance of such
systems and reduce its inherent variability. In this work, simulation is
used in the scheduling of re-entrant flow shop manufacturing systems
with an application in semiconductor wafer fabrication; where, a
simulation model has been developed for the Intel Five-Machine Six
Step Mini-Fab using the ExtendTM simulation environment. The
Mini-Fab has been selected as it captures the challenges involved in
scheduling the highly re-entrant semiconductor manufacturing lines.
A number of scenarios have been developed and have been used to
evaluate the effect of different dispatching rules and lot release
policies on the selected performance measures. Results of simulation
showed that the performance of the Mini-Fab can be drastically
improved using a combination of dispatching rules and lot release
policy.
Abstract: In this article, using finite element analysis (FEA)
and an X-ray diffractometer (XRD), cold-sprayed titanium particles
on a steel substrate is investigated in term of cooling time and the
development of residual strains. Three cooling-down models of
sprayed particles after deposition stage are simulated and discussed:
the first model (m1) considers conduction effect to the substrate only,
the second model (m2) considers both conduction as well as
convection effect to the environment, and the third model (m3) which
is the same as the second model but with the substrate heated to a
near particle temperature before spraying. Thereafter, residual strains
developed in the third model is compared with the experimental
measurement of residual strains, which involved a Bruker D8
Advance Diffractometer using CuKa radiation (40kV, 40mA)
monochromatised with a graphite sample monochromator. For
deposition conditions of this study, a good correlation was found to
exist between the FEA results and XRD measurements of residual
strains.
Abstract: Five original strains of entomopathogenic bacteria
with insecticidal activity against mosquito larvae of the genera Aedes,
Culex and Anopheles have been isolated from natural conditions in
Armenia and characterized. According to morphological,
physiological and biochemical parameters, all isolates were identified
as Bacillus thuringiensis spp. israelensis (Bti). High larvicidal
activity has been showed by three strains Bti. These strains can be
recommended for industrial production of bacterial preparations.
Abstract: Traffic enforcement units (the Police) are partly
responsible for the severity and frequency of the traffic accidents via
the effectiveness of their safety measures. The Police claims that the
reductions in accidents and their severities occur largely by their
timely interventions at the black spots, through traffic management
or temporary changes in the road design (guiding, reducing speeds
and eliminating sight obstructions, etc.). Yet, some other external
factors than the Police measures may intervene into which such
claims require a statistical confirmation. In order to test the net
impact of the Police contribution in the reduction of the number of
crashes, Chi square test was applied for 25 spots (streets and
intersections) and an average evaluation was achieved for general
conclusion in the case study of Izmir city. Separately, the net impact
of economic crisis in the reduction of crashes is assessed by the
trend analysis for the case of the economic crisis with the probable
reduction effects on the trip generation or modal choice. Finally, it
was proven that the Police measures were effective to some degree as
they claimed, though the economic crisis might have only negligible
contribution to the reductions in the same period observed.
Abstract: Adolescents in Northern Uganda are at risk of teenage
pregnancies, unsafe abortions and sexually transmitted infections
(STIs). There is silence on sex both at home and school. This cross
sectional descriptive analytical study interviews a random sample of
827 students and 13 teachers on knowledge, perception and
acceptability to a comprehensive adolescent sexual and reproductive
health education in “O” and “A” level secondary schools in Gulu
District. Quantitative data was analyzed using SPSS 16.0. Directed
content analysis of themes of transcribed qualitative data was
conducted manually for common codes, sub-categories and
categories. Of the 827 students; 54.3% (449) reported being in a
sexual relationship especially those aged 15-17 years. Majority
96.1% (807) supported the teaching of a comprehensive ASRHE,
citing no negative impact 71.5% (601). Majority 81.6% (686) agreed
that such education could help prevention of STIs, abortions and
teenage pregnancies, and that it should be taught by health workers
69.0% (580). Majority 76.6% (203) reported that ASRHE was not
currently being taught in their schools. Students had low knowledge
levels and misconceptions about ASRHE. ASRHE was highly
acceptable though not being emphasized; its success in school
settings requires multidisciplinary culturally sensitive approaches
amongst which health workers should be frontiers.
Abstract: Understanding how precipitation inter-annually
changes and its implication in agricultural drought and production change in winter wheat (Triticum aestivum L.) growth season is critical for crop production in China. MODIS Temperature-Vegetation Dryness Index (TVDI) and daily mean precipitation time series for the main growth season(Feb. to May) of winter wheat from 2000 to 2010
were used to analyze the distribution of trends of precipitation,
agricultural drought and winter wheat yield change respectively, and
relationships between them in North China region(Huang-huai-hai
region, HHH region), China. The results indicated that the trend of
precipitation in HHH region past 11 years was increasing, which had
induced generally corresponding decreasing trend of agricultural
drought and increasing trend of wheat yield, while the trend of drought
was spatially diverse. The study could provide a basis for agricultural
drought research during winter wheat season in HHH region under the
ground of climate change.
Abstract: Today, the preferences and participation of the TD groups such as the elderly and disabled is still lacking in decision-making of transportation planning, and their reactions to certain type of policies are not well known. Thus, a clear methodology is needed. This study aimed to develop a method to extract the preferences of the disabled to be used in the policy-making stage that can also guide to future estimations. The method utilizes the combination of cluster analysis and data filtering using the data of the Arao city (Japan). The method is a process that follows: defining the TD group by the cluster analysis tool, their travel preferences in tabular form from the household surveys by policy variableimpact pairs, zones, and by trip purposes, and the final outcome is the preference probabilities of the disabled. The preferences vary by trip purpose; for the work trips, accessibility and transit system quality policies with the accompanying impacts of modal shifts towards public mode use as well as the decreasing travel costs, and the trip rate increase; for the social trips, the same accessibility and transit system policies leading to the same mode shift impact, together with the travel quality policy area leading to trip rate increase. These results explain the policies to focus and can be used in scenario generation in models, or any other planning purpose as decision support tool.
Abstract: A considerable progress has been achieved in transient
stability analysis (TSA) with various FACTS controllers. But, all
these controllers are associated with single transmission line. This
paper is intended to discuss a new approach i.e. a multi-line FACTS
controller which is interline power flow controller (IPFC) for TSA of
a multi-machine power system network. A mathematical model of
IPFC, termed as power injection model (PIM) presented and this
model is incorporated in Newton-Raphson (NR) power flow
algorithm. Then, the reduced admittance matrix of a multi-machine
power system network for a three phase fault without and with IPFC
is obtained which is required to draw the machine swing curves. A
general approach based on L-index has also been discussed to find
the best location of IPFC to reduce the proximity to instability of a
power system. Numerical results are carried out on two test systems
namely, 6-bus and 11-bus systems. A program in MATLAB has
been written to plot the variation of generator rotor angle and speed
difference curves without and with IPFC for TSA and also a simple
approach has been presented to evaluate critical clearing time for test
systems. The results obtained without and with IPFC are compared
and discussed.
Abstract: A new interface circuit for capacitive sensor is
presented. This paper presents the design and simulation of soil
moisture capacitive sensor interface circuit based on phase
differential technique. The circuit has been designed and fabricated
using MIMOS- 0.35"m CMOS technology. Simulation and test
results show linear characteristic from 36 – 52 degree phase
difference, representing 0 – 100% in soil moisture level. Test result
shows the circuit has sensitivity of 0.79mV/0.10 phase difference,
translating into resolution of 10% soil moisture level.
Abstract: QoS Routing aims to find paths between senders and
receivers satisfying the QoS requirements of the application which
efficiently using the network resources and underlying routing
algorithm to be able to find low-cost paths that satisfy given QoS
constraints. The problem of finding least-cost routing is known to be
NP-hard or complete and some algorithms have been proposed to
find a near optimal solution. But these heuristics or algorithms either
impose relationships among the link metrics to reduce the complexity
of the problem which may limit the general applicability of the
heuristic, or are too costly in terms of execution time to be applicable
to large networks. In this paper, we concentrate an algorithm that
finds a near-optimal solution fast and we named this algorithm as
optimized Delay Constrained Routing (ODCR), which uses an
adaptive path weight function together with an additional constraint
imposed on the path cost, to restrict search space and hence ODCR
finds near optimal solution in much quicker time.
Abstract: One of the major cause of eye strain and other
problems caused while watching television is the relative illumination between the screen and its surrounding. This can be
overcome by adjusting the brightness of the screen with respect to the surrounding light. A controller based on fuzzy logic is proposed
in this paper. The fuzzy controller takes in the intensity of light
surrounding the screen and the present brightness of the screen as input. The output of the fuzzy controller is the grid voltage corresponding to the required brightness. This voltage is given to CRT and brightness is controller dynamically. For the given test system data, different de-fuzzifier methods have been implemented and the results are compared. In order to validate the effectiveness of
the proposed approach, a fuzzy controller has been designed by obtaining a test data from a real time system. The simulations are
performed in MATLAB and are verified with standard system data. The proposed approach can be implemented for real time
applications.
Abstract: Electroencephalogram (EEG) recordings are often
contaminated with ocular and muscle artifacts. In this paper, the
canonical correlation analysis (CCA) is used as blind source
separation (BSS) technique (BSS-CCA) to decompose the artifact
contaminated EEG into component signals. We combine the BSSCCA
technique with wavelet filtering approach for minimizing both
ocular and muscle artifacts simultaneously, and refer the proposed
method as wavelet enhanced BSS-CCA. In this approach, after
careful visual inspection, the muscle artifact components are
discarded and ocular artifact components are subjected to wavelet
filtering to retain high frequency cerebral information, and then clean
EEG is reconstructed. The performance of the proposed wavelet
enhanced BSS-CCA method is tested on real EEG recordings
contaminated with ocular and muscle artifacts, for which power
spectral density is used as a quantitative measure. Our results suggest
that the proposed hybrid approach minimizes ocular and muscle
artifacts effectively, minimally affecting underlying cerebral activity
in EEG recordings.
Abstract: It has been shown that pH 7,3 and 37 0C are the optimal condition for the growth of E. coli “ASAP". The cells grow well on Glucose, Lactose, D-Mannitol, D-Sorbitol, (+)-Xylose, L- (+)-Arabinose and Dulcitol. No growth has been observed on Sucrose, Inositol, Phenylalanine, and Tryptophan. The strain is sensitive to a range of antibiotics. The present study has demonstrated that E. coli “ASAP" inhibit the growth of S. enterica ATCC #700931 in vitro. The studies on conjugating activity has revealed no conjugant of E. coli “ASAP" with plasmid strains E. coli G35#59 and S. enterica ATCC #700931. On the other hand, the conjugants with low frequencies were obtained from E. coli “ASAP" with E. coli G35#61, and E. coli “ASAP" with randomly chosen isolate from healthy human gut microflora: E. coli E6. The results of present study have demonstrated improvements in gut microflora condition of patients with different diseases after the administration of “ASAP"
Abstract: Dioscorea species or commonly named as yam is
reported to be one of the major food sources worldwide. This
ethnobotanical study was conducted to document local knowledge
and potentials of DioscoreahispidaDennst. and to investigate and
record its distribution in three districts of Terengganu. Information
was gathered from 23 villagers from three districts of Besut, Marang
and Setiu by using semi-structured questionnaire. The villagers were
randomly selected and no appointment was made prior to the visits.
For distribution, the location of Dioscoreahispida was recorded by
using the Global Positioning System (GPS). The villagers identified
Dioscoreahispida or locally named ubigadong by looking at the
physical characteristics that include its leaf shape, stem and the color
of the tuber-s flesh. The villagers used Dioscoreahispida in many
ways in their life such as for food, medicinal purposes and fish
poison.
Abstract: Virtual engineering technology has undergone rapid progress in recent years and is being adopted increasingly by manufacturing companies of many engineering disciplines. There is an increasing demand from industry for qualified virtual engineers. The qualified virtual engineers should have the ability of applying engineering principles and mechanical design methods within the commercial software package environment. It is a challenge to the engineering education in universities which traditionally tends to lack the integration of knowledge and skills required for solving real world problems. In this paper, a case study shows some recent development of a MSc Mechanical Engineering course at Department of Engineering and Technology in MMU, and in particular, two units Simulation of Mechanical Systems(SMS) and Computer Aided Fatigue Analysis(CAFA) that emphasize virtual engineering education and promote integration of knowledge acquisition, skill training and industrial application.
Abstract: In general fuzzy sets are used to analyze the fuzzy
system reliability. Here intuitionistic fuzzy set theory for analyzing
the fuzzy system reliability has been used. To analyze the fuzzy
system reliability, the reliability of each component of the system as
a triangular intuitionistic fuzzy number is considered. Triangular
intuitionistic fuzzy number and their arithmetic operations are
introduced. Expressions for computing the fuzzy reliability of a
series system and a parallel system following triangular intuitionistic
fuzzy numbers have been described. Here an imprecise reliability
model of an electric network model of dark room is taken. To
compute the imprecise reliability of the above said system, reliability
of each component of the systems is represented by triangular
intuitionistic fuzzy numbers. Respective numerical example is
presented.