Abstract: Climate change and environmental pressures are
major international issues nowadays. It is time when governments,
businesses and consumers have to respond through more
environmentally friendly and aware practices, products and policies.
This is the prime time to develop alternative sustainable construction
materials, reduce greenhouse gas emissions, save energy, look to
renewable energy sources and recycled materials, and reduce waste.
The utilization of waste materials (slag, fly ash, glass beads, plastic
and so on) in concrete manufacturing is significant due to its
engineering, financial, environmental and ecological benefits. Thus,
utilization of waste materials in concrete production is very much
helpful to reach the goal of the sustainable construction. Therefore,
this study intends to use glass beads in concrete production.
The paper reports on the performance of 9 different concrete
mixes containing different ratios of glass crushed to 5 mm - 20 mm
maximum size and glass marble of 20 mm size as coarse aggregate.
Ordinary Portland cement type 1 and fine sand less than 0.5 mm were
used to produce standard concrete cylinders. Compressive strength
tests were carried out on concrete specimens at various ages. Test
results indicated that the mix having the balanced ratio of glass beads
and round marbles possess maximum compressive strength which is
3889 psi, as glass beads perform better in bond formation but have
lower strength, on the other hand marbles are strong in themselves
but not good in bonding. These mixes were prepared following a
specific W/C and aggregate ratio; more strength can be expected to
achieve from different W/C, aggregate ratios, adding admixtures like
strength increasing agents, ASR inhibitor agents etc.
Abstract: There are a many of needs for the development of
SiC-based hydrogen sensor for harsh environment applications. We
fabricated and investigated Pd/Ta2O5/SiC-based hydrogen sensors
with MOS capacitor structure for high temperature process monitoring
and leak detection applications in such automotive, chemical and
petroleum industries as well as direct monitoring of combustion
processes. In this work, we used silicon carbide (SiC) as a substrate to
replace silicon which operating temperatures are limited to below
200°C. Tantalum oxide was investigated as dielectric layer which has
high permeability for hydrogen gas and high dielectric permittivity,
compared with silicon dioxide or silicon nitride. Then, electrical
response properties, such as I-V curve and dependence of capacitance
on hydrogen concentrations were analyzed in the temperature ranges
of room temperature to 500°C for performance evaluation of the
sensor.
Abstract: As we know, most differential equations concerning
physical phenomenon could not be solved by analytical method. Even if we use Series Method, some times we need an appropriate change of variable, and even when we can, their closed form solution may be
so complicated that using it to obtain an image or to examine the structure of the system is impossible. For example, if we consider Schrodinger equation, i.e.,
We come to a three-term recursion relations, which work with it takes, at least, a little bit time to get a series solution[6]. For this
reason we use a change of variable such as or when we consider the orbital angular momentum[1], it will be
necessary to solve. As we can observe, working with this equation is tedious. In this paper, after introducing Clenshaw method, which is a kind of Spectral method, we try to solve some of such equations.
Abstract: This paper presents data annotation models at
five levels of granularity (database, relation, column, tuple, and cell) of relational data to address the problem of unsuitability of most relational databases to express annotations. These models
do not require any structural and schematic changes to the
underlying database. These models are also flexible, extensible,
customizable, database-neutral, and platform-independent. This paper also presents an SQL-like query language, named Annotation Query Language (AnQL), to query annotation documents. AnQL is simple to understand and exploits the already-existent wide knowledge and skill set of SQL.
Abstract: The aim of the paper work is to investigate and predict
the static performance of journal bearing in turbulent flow condition
considering micropolar lubrication. The Reynolds equation has been
modified considering turbulent micropolar lubrication and is solved
for steady state operations. The Constantinescu-s turbulence model is
adopted using the coefficients. The analysis has been done for a
parallel and inertia less flow. Load capacity and friction factor have
been evaluated for various operating parameters.
Abstract: According to celebrated Hurwitz theorem, there exists
four division algebras consisting of R (real numbers), C (complex
numbers), H (quaternions) and O (octonions). Keeping in view
the utility of octonion variable we have tried to extend the three
dimensional vector analysis to seven dimensional one. Starting with
the scalar and vector product in seven dimensions, we have redefined
the gradient, divergence and curl in seven dimension. It is shown
that the identity n(n - 1)(n - 3)(n - 7) = 0 is satisfied only
for 0, 1, 3 and 7 dimensional vectors. We have tried to write all
the vector inequalities and formulas in terms of seven dimensions
and it is shown that same formulas loose their meaning in seven
dimensions due to non-associativity of octonions. The vector formulas
are retained only if we put certain restrictions on octonions and split
octonions.
Abstract: Pyrite (FeS2) is a promising candidate for cathode
materials in batteries because of it`s high theoretical capacity, low
cost and non-toxicity. In this study, nano size iron disulfide thin film
was prepared on graphite substrate through a new method as battery
cathode. In this way, acetylene black and poly vinylidene fluoride
were used as electron conductor and binder, respectively. Fabricated
thin films were analyzed by XRD and SEM. These results and
electrochemical data confirm improvement of battery discharge
capacity in comparison with commercial type of pyrite.
Abstract: IFP Group Technology “Sulfrex process" was used in
Iran-s South Pars Gas Complex Refineries for removing sulfur
compounds such as mercaptans, carbonyl sulfide and hydrogen
sulfide, which uses sulfonated cobalt phthalocyanine dispersed in
alkaline solution as catalyst. In this technology, catalyst and alkaline
solution were used circularly. However the stability of catalyst due to
effect of some parameters would reduce with the running of the unit
and therefore sweetening efficiency would be decreased. Hence, the
aim of this research is study the factors effecting on the stability of
catalyst.
Abstract: Precast concrete has been widely adopted in public
housing construction of Hong Kong since the mid-1980s. While
pre-casting is considered an environmental friendly solution, there is
lack of study to investigate the life cycle performance of precast
concrete units. This study aims to bridge the knowledge gap by
providing a comprehensive life cycle assessment (LCA) study for two
precast elements namely façade and bathroom. The results show that
raw material is the most significant contributor of environmental
impact accounting for about 90% to the total impact. Furthermore,
human health is more affected by the production of precast concrete
than the ecosystems.
Abstract: This paper presents an approach for the determination of the optimal cutting parameters (spindle speed, feed rate, depth of cut and engagement) leading to minimum surface roughness in face milling of high silicon stainless steel by coupling neural network (NN) and Electromagnetism-like Algorithm (EM). In this regard, the advantages of statistical experimental design technique, experimental measurements, artificial neural network, and Electromagnetism-like optimization method are exploited in an integrated manner. To this end, numerous experiments on this stainless steel were conducted to obtain surface roughness values. A predictive model for surface roughness is created by using a back propogation neural network, then the optimization problem was solved by using EM optimization. Additional experiments were performed to validate optimum surface roughness value predicted by EM algorithm. It is clearly seen that a good agreement is observed between the predicted values by EM coupled with feed forward neural network and experimental measurements. The obtained results show that the EM algorithm coupled with back propogation neural network is an efficient and accurate method in approaching the global minimum of surface roughness in face milling.
Abstract: The demands of taller structures are becoming imperative almost everywhere in the world in addition to the challenges of material and labor cost, project time line etc. This paper conducted a study keeping in view the challenging nature of high-rise construction with no generic rules for deflection minimizations and frequency control. The effects of cyclonic wind and provision of outriggers on 28-storey, 42-storey and 57-storey are examined in this paper and certain conclusions are made which would pave way for researchers to conduct further study in this particular area of civil engineering. The results show that plan dimensions have vital impacts on structural heights. Increase of height while keeping the plan dimensions same, leads to the reduction in the lateral rigidity. To achieve required stiffness increase of bracings sizes as well as introduction of additional lateral resisting system such as belt truss and outriggers is required.
Abstract: In recent years, strategic alliances have taken
increasing importance as a means to control competitive forces and to
enter into new markets. Joint ventures are one of the most frequently
used contractual forms in strategic alliances. There are various
motivations for cooperation between two or more firms e.g.,
accessing to technical know-how, accessing to financial resources
and managing risks. The firms must know about these motivations to
encourage for establishing joint venture. So, it is important for
managers to understand about these motives. On the other hand, the
cooperation section is one of the most effective parts in each country.
In this way, our study identifies goals of joint venture between
cooperative manufacturing firms, and prioritizes those using
TOPSIS1. The results show that the most important of joint venture
goals are: accessing to managerial know-how, sharing total capital
investment.
Abstract: Later marine propeller is the main component of ship
propulsion system. For a non-series propeller, it is difficult to
indicate the open water marine propeller performance without an
experimental study to measure the marine propeller parameters.
In the present study, the open water performance of a non-series
marine propeller has been carried out experimentally. The
geometrical aspects of a commercial non-series marine propeller
have been measured for a propeller blade area ratio of 0.3985. The
measured propeller performance parameters were the thrust and
torque coefficients for different propeller rotational speed and
different water channel flow velocity, then the open water
performance for the propeller has been plotted.
In addition, a direct comparison between the obtained
experimental results and a theoretical study of a B-series marine
propeller of the same blade area ratio has been carried out. A
correction factor has been introduced to apply the operating
conditions of the experimental results to that of the theoretical study
for the studied marine propeller.
Abstract: Implemented 5-bit 125-MS/s successive
approximation register (SAR) analog to digital converter (ADC) on
FPGA is presented in this paper.The design and modeling of a high
performance SAR analog to digital converter are based on monotonic
capacitor switching procedure algorithm .Spartan 3 FPGA is chosen
for implementing SAR analog to digital converter algorithm. SAR
VHDL program writes in Xilinx and modelsim uses for showing
results.
Abstract: This paper presents the stabilization potential of Class
F pond ash (PA) from a coal fired thermal power station on tropical
peat soil. Peat or highly organic soils are well known for their high
compressibility, natural moisture content, low shear strength and
long-term settlement. This study investigates the effect of different
amount (i.e., 5, 10, 15 and 20%) of PA on peat soil, collected from
Sarawak, Malaysia, mainly compaction and unconfined compressive
strength (UCS) properties. The amounts of PA added to the peat soil
sample as percentage of the dry peat soil mass. With the increase in
PA content, the maximum dry density (MDD) of peat soil increases,
while the optimum moisture content (OMC) decreases. The UCS
value of the peat soils increases significantly with the increase of PA
content and also with curing periods. This improvement on
compressive strength of tropical peat soils indicates that PA has the
potential to be used as a stabilizer for tropical peat soil. Also, the use
of PA in soil stabilization helps in reducing the pond volume and
achieving environment friendly as well as a sustainable development
of natural resources.
Abstract: Curing of paints by exposure to UV radiations is
emerging as one of the best film forming technique as an alternative
to traditional solvent borne oxidative and thermal curing coatings.
The composition and chemistry of UV curable coatings and role of
multifunctional and monofunctional monomers, oligomers, and
photoinitiators have been discussed. The limitations imposed by
thermodynamic equilibrium and tendency for acrylic double bond
polymerizations during synthesis of multifunctional acrylates have
been presented. Aim of present investigation was thus to explore the
reaction variables associated with synthesis of multifunctional
acrylates. Zirconium oxychloride was evaluated as catalyst against
regular acid functional catalyst. The catalyzed synthesis of glyceryl
acrylate and neopentyl glycol acrylate was conducted by variation of
following reaction parameters: two different reactant molar ratios-
1:4 and 1:6; catalyst usage in % by moles on polyol- 2.5, 5.0 and 7.5
and two different reaction temperatures- 45 and 75 0C. The reaction
was monitored by determination of acid value and hydroxy value at
regular intervals, besides TLC, HPLC, and FTIR analysis of
intermediates and products. On the basis of determination of reaction
progress over 1-60 hrs, the esterification reaction was observed to
follow 2nd order kinetics with rate constant varying from 1*10-4 to
7*10-4. The thermal and catalytic components of second order rate
constant and energy of activation were also determined. Uses of
these kinetic and thermodynamic parameters in design of reactor for
manufacture of multifunctional acrylate ester have been presented.
The synthesized multifunctional acrylates were used to formulate and
apply UV curable clear coat followed by determination of curing
characteristics and mechanical properties of cured film. The overall
curing rates less than 05 min. were easily attained indicating
economical viability of radiation curable system due to faster
production schedules
Abstract: The conjugate gradient optimization algorithm is combined with the modified back propagation algorithm to yield a computationally efficient algorithm for training multilayer perceptron (MLP) networks (CGFR/AG). The computational efficiency is enhanced by adaptively modifying initial search direction as described in the following steps: (1) Modification on standard back propagation algorithm by introducing a gain variation term in the activation function, (2) Calculation of the gradient descent of error with respect to the weights and gains values and (3) the determination of a new search direction by using information calculated in step (2). The performance of the proposed method is demonstrated by comparing accuracy and computation time with the conjugate gradient algorithm used in MATLAB neural network toolbox. The results show that the computational efficiency of the proposed method was better than the standard conjugate gradient algorithm.
Abstract: In this paper we present an energy efficient match-line
(ML) sensing scheme for high-speed ternary content-addressable
memory (TCAM). The proposed scheme isolates the sensing unit of
the sense amplifier from the large and variable ML capacitance. It
employs feedback in the sense amplifier to successfully detect a
match while keeping the ML voltage swing low. This reduced voltage
swing results in large energy saving. Simulation performed using
130nm 1.2V CMOS logic shows at least 30% total energy saving in
our scheme compared to popular current race (CR) scheme for
similar search speed. In terms of speed, dynamic energy, peak power
consumption and transistor count our scheme also shows better
performance than mismatch-dependant (MD) power allocation
technique which also employs feedback in the sense amplifier.
Additionally, the implementation of our scheme is simpler than CR
or MD scheme because of absence of analog control voltage and
programmable delay circuit as have been used in those schemes.
Abstract: This paper presents a general trainable framework
for fast and robust upright human face and non-human object
detection and verification in static images. To enhance the
performance of the detection process, the technique we develop is
based on the combination of fast neural network (FNN) and
classical neural network (CNN). In FNN, a useful correlation is
exploited to sustain high level of detection accuracy between input
image and the weight of the hidden neurons. This is to enable the
use of Fourier transform that significantly speed up the time
detection. The combination of CNN is responsible to verify the
face region. A bootstrap algorithm is used to collect non human
object, which adds the false detection to the training process of the
human and non-human object. Experimental results on test images
with both simple and complex background demonstrate that the
proposed method has obtained high detection rate and low false
positive rate in detecting both human face and non-human object.
Abstract: A modified Saleh-Valenzuela channel model has been
adapted for Ultra Wideband (UWB) system. The suggested realistic
channel is assessed by its distribution of fading amplitude and time of
arrivals. Furthermore, the propagation characteristic has been distinct
into four channel models, namely CM 1 to 4. Each are differentiate in
terms of cluster arrival rates, rays arrival rate within each cluster and
its respective constant decay rates. This paper described the
multiband OFDM system performance simulates under these
multipath conditions. Simulation work described in this paper is
based on WiMedia ECMA-368 standard, which has been deployed
for practical implementation of low cost and low power UWB
devices.