Abstract: This paper presents the results related to the
interference reduction technique in multistage multiuser detector for
asynchronous DS-CDMA system. To meet the real-time
requirements for asynchronous multiuser detection, a bit streaming,
cascade architecture is used. An asynchronous multiuser detection
involves block-based computations and matrix inversions. The paper
covers iterative-based suboptimal schemes that have been studied to
decrease the computational complexity, eliminate the need for matrix
inversions, decreases the execution time, reduces the memory
requirements and uses joint estimation and detection process that
gives better performance than the independent parameter estimation
method. The stages of the iteration use cascaded and bits processed
in a streaming fashion. The simulation has been carried out for
asynchronous DS-CDMA system by varying one parameter, i.e.,
number of users. The simulation result exhibits that system gives
optimum bit error rate (BER) at 3rd stage for 15-users.
Abstract: State tax revenues in most countries started to decrease during the recession. Government of Latvia decided to compensate the decline by increasing rates of several taxes including excise tax on strong alcohol. The total increase in 2009 constituted 42% and the rate increased from 896€ to 1 266€ for 100l of absolute alcohol. Since then this has had a negative impact on consumption volumes and the split between legal and illegal market. The legal alcohol sales decreased by almost 50% (by volume), consequentially having negative effect on the State revenues from VAT and excise tax. Estimated results for 2010 are indicating 54 million € decrease in VAT, excise tax and other taxes versus 2008 (excise tax -19 million €, VAT -30 million €, other taxes -5 million €). The paper aims to analyze impact of the increase in excise tax on consumption patterns, State revenues and competitiveness of the local companies to draw up proposals for the state authorities regarding more effective tax policies. The analysis reveals a relationship between excise tax rate, illegal alcohol market and State revenues. The results can be used to improve excise tax system and effectiveness in Latvia.
Abstract: This research deals with investigations on the “Active
Generator" under rotor speed variations and output frequency
control. It runs at turbine speed and it is connected to a three phase
electrical power grid which has its own frequency different from
turbine frequency. In this regard the set composed of a four phase
synchronous generator and a natural commutated matrix converter
(NCMC) made with thyristors, is called active generator. It replaces a
classical mechanical gearbox which introduces many drawbacks. The
main idea in this article is the presentation of frequency control at
grid side when turbine runs at variable speed. Frequency control has
been done by linear and step variations of the turbine speed. Relation
between turbine speed (frequency) and main grid zero sequence
voltage frequency is presented.
Abstract: The objective of this study is to determine the thermal comfort among worker at Malaysian automotive industry. One critical manual assembly workstation had been chosen as a subject for the study. The human subjects for the study constitute operators at Body Assembly Station of the factory. The environment examined was the Relative Humidity (%), Airflow (m/s), Air Temperature (°C) and Radiant Temperature (°C) of the surrounding workstation area. The environmental factors were measured using Babuc apparatus, which is capable to measure simultaneously those mentioned environmental factors. The time series data of fluctuating level of factors were plotted to identify the significant changes of factors. Then thermal comfort of the workers were assessed by using ISO Standard 7730 Thermal sensation scale by using Predicted Mean Vote (PMV). Further Predicted percentage dissatisfied (PPD) is used to estimate the thermal comfort satisfaction of the occupant. Finally the PPD versus PMV were plotted to present the thermal comfort scenario of workers involved in related workstation. The result of PMV at the related industry is between 1.8 and 2.3, where PPD at that building is between 60% to 84%. The survey result indicated that the temperature more influenced comfort to the occupants
Abstract: The overall objective of this paper is to retrieve soil
surfaces parameters namely, roughness and soil moisture related to
the dielectric constant by inverting the radar backscattered signal
from natural soil surfaces.
Because the classical description of roughness using statistical
parameters like the correlation length doesn't lead to satisfactory
results to predict radar backscattering, we used a multi-scale
roughness description using the wavelet transform and the Mallat
algorithm. In this description, the surface is considered as a
superposition of a finite number of one-dimensional Gaussian
processes each having a spatial scale. A second step in this study
consisted in adapting a direct model simulating radar backscattering
namely the small perturbation model to this multi-scale surface
description. We investigated the impact of this description on radar
backscattering through a sensitivity analysis of backscattering
coefficient to the multi-scale roughness parameters.
To perform the inversion of the small perturbation multi-scale
scattering model (MLS SPM) we used a multi-layer neural network
architecture trained by backpropagation learning rule. The inversion
leads to satisfactory results with a relative uncertainty of 8%.
Abstract: Three-phase induction machines are today a standard
for industrial electrical drives. Cost, reliability, robustness and maintenance free operation are among the reasons these machines are
replacing dc drive systems. The development of power electronics
and signal processing systems has eliminated one of the greatest
disadvantages of such ac systems, which is the issue of control. With
modern techniques of field oriented vector control, the task of
variable speed control of induction machines is no longer a
disadvantage. The need to increase system performance, particularly
when facing limits on the power ratings of power supplies and
semiconductors, motivates the use of phase number other than three,
In this paper a novel scheme of connecting two, three phase
induction motors in parallel fed by two inverters; viz. VSI and CSI
and their vector control is presented.
Abstract: The effect of nano Co3O4 addition on the
superconducting properties of (Bi, Pb)-2223 system was studied. The
samples were prepared by the acetate coprecipitation method. The
Co3O4 with different sizes (10-30 nm and 30-50 nm) from x=0.00 to
0.05 was added to Bi1.6Pb0.4Sr2Ca2Cu3Oy(Co3O4)x. Phase analysis by
XRD method, microstructural examination by SEM and dc electrical
resistivity by four point probe method were done to characterize the
samples. The X-ray diffraction patterns of all the samples indicated
the majority Bi-2223 phase along with minor Bi-2212 and Bi-2201
phases. The volume fraction was estimated from the intensities of Bi-
2223, Bi-2212 and Bi-2201 phase. The sample with x=0.01 wt% of
the added Co3O4 (10-30 nm size) showed the highest volume fraction
of Bi-2223 phase (72%) and the highest superconducting transition
temperature, Tc (~102 K). The non-added sample showed the highest
Tc(~103 K) compared to added samples with nano Co3O4 (30-50 nm
size) added samples. Both the onset critical temperature Tc(onset)
and zero electrical resistivity temperature Tc(R=0) were in the range
of 103-115 ±1K and 91-103 ±1K respectively for samples with added
Co3O4 (10-30 nm and 30-50 nm).
Abstract: The given work is devoted to the description of
Information Technologies NAS of Azerbaijan created and
successfully maintained in Institute. On the basis of the decision of
board of the Supreme Certifying commission at the President of the
Azerbaijan Republic and Presidium of National Academy of
Sciences of the Azerbaijan Republic, the organization of training
courses on Computer Sciences for all post-graduate students and
dissertators of the republic, taking of examinations of candidate
minima, it was on-line entrusted to Institute of Information
Technologies of the National Academy of Sciences of Azerbaijan.
Therefore, teaching the computer sciences to post-graduate
students and dissertators a scientific - methodological manual on
effective application of new information technologies for research
works by post-graduate students and dissertators and taking of
candidate minima is carried out in the Educational Center.
Information and communication technologies offer new
opportunities and prospects of their application for teaching and
training. The new level of literacy demands creation of essentially
new technology of obtaining of scientific knowledge. Methods of
training and development, social and professional requirements,
globalization of the communicative economic and political projects
connected with construction of a new society, depends on a level of
application of information and communication technologies in the
educational process. Computer technologies develop ideas of
programmed training, open completely new, not investigated
technological ways of training connected to unique opportunities of
modern computers and telecommunications. Computer technologies
of training are processes of preparation and transfer of the
information to the trainee by means of computer. Scientific and
technical progress as well as global spread of the technologies
created in the most developed countries of the world is the main
proof of the leading role of education in XXI century. Information
society needs individuals having modern knowledge. In practice, all
technologies, using special technical information means (computer,
audio, video) are called information technologies of education.
Abstract: The comparative analysis of different taxonomic
groups of microorganisms isolated from dark chernozem soils under
different agricultures (alfalfa, melilot, sainfoin, soybean, rapeseed) at
Almaty region of Kazakhstan was conducted. It was shown that the
greatest number of micromycetes was typical to the soil planted with
alfalfa and canola. Species diversity of micromycetes markedly
decreases as it approaches the surface of the root, so that the species
composition in the rhizosphere is much more uniform than in the
virgin soil. Promising strains of microscopic fungi and yeast with
plant growth-promoting activity to agricultures were selected. Among
the selected fungi there are representatives of Penicillium bilaiae,
Trichoderma koningii, Fusarium equiseti, Aspergillus ustus. The
highest rates of growth and development of seedlings of plants
observed under the influence of yeasts Aureobasidium pullulans,
Rhodotorula mucilaginosa, Metschnikovia pulcherrima. Using
molecular - genetic techniques confirmation of the identification
results of selected micromycetes was conducted.
Abstract: An on chip low drop out voltage regulator that
employs elegant compensation scheme is presented in this paper. The
novelty in this design is that the device parasitic capacitances are
exploited for compensation at different loads. The proposed LDO is
designed to provide a constant voltage of 1.2V and is implemented in
UMC 180 nano meter CMOS technology. The voltage regulator
presented improves stability even at lighter loads and enhances line
and load regulation.
Abstract: Generalized Center String (GCS) problem are
generalized from Common Approximate Substring problem
and Common substring problems. GCS are known to be
NP-hard allowing the problems lies in the explosion of
potential candidates. Finding longest center string without
concerning the sequence that may not contain any motifs is
not known in advance in any particular biological gene
process. GCS solved by frequent pattern-mining techniques
and known to be fixed parameter tractable based on the
fixed input sequence length and symbol set size. Efficient
method known as Bpriori algorithms can solve GCS with
reasonable time/space complexities. Bpriori 2 and Bpriori
3-2 algorithm are been proposed of any length and any
positions of all their instances in input sequences. In this
paper, we reduced the time/space complexity of Bpriori
algorithm by Constrained Based Frequent Pattern mining
(CBFP) technique which integrates the idea of Constraint
Based Mining and FP-tree mining. CBFP mining technique
solves the GCS problem works for all center string of any
length, but also for the positions of all their mutated copies
of input sequence. CBFP mining technique construct TRIE
like with FP tree to represent the mutated copies of center
string of any length, along with constraints to restraint
growth of the consensus tree. The complexity analysis for
Constrained Based FP mining technique and Bpriori
algorithm is done based on the worst case and average case
approach. Algorithm's correctness compared with the
Bpriori algorithm using artificial data is shown.
Abstract: In Virtual organization, Knowledge Discovery (KD)
service contains distributed data resources and computing grid nodes.
Computational grid is integrated with data grid to form Knowledge
Grid, which implements Apriori algorithm for mining association
rule on grid network. This paper describes development of parallel
and distributed version of Apriori algorithm on Globus Toolkit using
Message Passing Interface extended with Grid Services (MPICHG2).
The creation of Knowledge Grid on top of data and
computational grid is to support decision making in real time
applications. In this paper, the case study describes design and
implementation of local and global mining of frequent item sets. The
experiments were conducted on different configurations of grid
network and computation time was recorded for each operation. We
analyzed our result with various grid configurations and it shows
speedup of computation time is almost superlinear.
Abstract: Collision is considered as a time-depended nonlinear
dynamic phenomenon. The majority of researchers have focused on
deriving the resultant damage of the ship collisions via analytical,
experimental, and finite element methods.In this paper, first, the
force-penetration curve of a head collision on a container ship with
rigid barrier based on Yang and Pedersen-s methods for internal
mechanic section is studied. Next, the obtained results from different
analytical methods are compared with each others. Then, through a
simulation of the container ship collision in Ansys Ls-Dyna, results
from finite element approach are compared with analytical methods
and the source of errors is discussed. Finally, the effects of
parameters such as velocity, and angle of collision on the forcepenetration
curve are investigated.
Abstract: Within dental-guided surgery, there has been a lack
of analytical methods for optimizing the treatment of the
rehabilitation concepts regarding geometrical variation. The purpose
of this study is to find the source of the greatest geometrical variation
contributor and sensitivity contributor with the help of virtual
variation simulation of a dental drill- and implant-guided surgery
process using a methodical approach. It is believed that lower
geometrical variation will lead to better patient security and higher
quality of dental drill- and implant-guided surgeries. It was found
that the origin of the greatest contributor to the most variation, and
hence where the foci should be set, in order to minimize geometrical
variation was in the assembly category (surgery). This was also the
category that was the most sensitive for geometrical variation.
Abstract: Light rail systems have proliferated in Spain in the last decade, following a tendency that is common not only in other European countries but also in other parts of the world. This paper reviews the benefits of light rail systems, both related to environmental issues and mobility issues. It analyses the evolution of light rail projects in Spain and shows that light rail systems in this country have evolved towards an extensive use of public-private partnerships. The analysis of the Spanish projects, however, does not contribute any conclusive evidence about whether public-private partnerships have been more efficient than publicly owned enterprises in building and operating light rail systems.
Abstract: Active power filter continues to be a powerful tool to control harmonics in power systems thereby enhancing the power quality. This paper presents a fuzzy tuned PID controller based shunt active filter to diminish the harmonics caused by non linear loads like thyristor bridge rectifiers and imbalanced loads. Here Fuzzy controller provides the tuning of PID, based on firing of thyristor bridge rectifiers and variations in input rms current. The shunt APF system is implemented with three phase current controlled Voltage Source Inverter (VSI) and is connected at the point of common coupling for compensating the current harmonics by injecting equal but opposite filter currents. These controllers are capable of controlling dc-side capacitor voltage and estimating reference currents. Hysteresis Current Controller (HCC) is used to generate switching signals for the voltage source inverter. Simulation studies are carried out with non linear loads like thyristor bridge rectifier along with unbalanced loads and the results proved that the APF along with fuzzy tuned PID controller work flawlessly for different firing angles of non linear load.
Abstract: In realizing devices using ZnO, a key challenge is the
production of p-type material. Substitution of oxygen by a group-V
impurity is thought to result in deep acceptor levels, but a candidate
made up from a complex of a group-V impurity (P, As, Sb) on a Zn
site coupled with two vacant Zn sites is widely viewed as a candidate.
We show using density-functional simulations that in contrast to such
a view, complexes involving oxygen interstitials are energetically
more favorable, resulting in group-V impurities coordinated with four,
five or six oxygen atoms.
Abstract: Linear induction motors are used in various industries
but they have some specific phenomena which are the causes for
some problems. The most important phenomenon is called end effect.
End effect decreases efficiency, power factor and output force and
unbalances the phase currents. This phenomenon is more important
in medium and high speeds machines. In this paper a factor, EEF , is
obtained by an accurate equivalent circuit model, to determine the
end effect intensity. In this way, all of effective design parameters on
end effect is described. Accuracy of this equivalent circuit model is
evaluated by two dimensional finite-element analysis using ANSYS.
The results show the accuracy of the equivalent circuit model.
Abstract: Organic farmers across Saskatchewan face soil
phosphorus (P) shortages. Due to the restriction on inputs in organic
systems, farmers rely on crop rotation and naturally-occurring
arbuscular mycorrhizal fungi (AMF) for plant P supply. Crop rotation
is important for disease, pest, and weed management. Crops that are
not colonized by AMF (non-mycorrhizal) can decrease colonization
of a following crop. An experiment was performed to quantify soil P
cycling in four cropping sequences under organic management and
determine if mustard (non-mycorrhizal) was delaying the
colonization of subsequent wheat. Soils from the four cropping
sequences were measured for inorganic soil P (Pi), AMF spore
density (SD), phospholipid fatty acid analysis (PLFA, for AMF
biomarker counts), and alkaline phosphatase activity (ALPase,
related to AMF metabolic activity). Plants were measured for AMF
colonization and P content and uptake of above-ground biomass. A
lack of difference in AMF activity indicated that mustard was not
depressing colonization. Instead, AMF colonization was largely
determined by crop type and crop rotation.
Abstract: As we know, most differential equations concerning
physical phenomenon could not be solved by analytical method. Even if we use Series Method, some times we need an appropriate change of variable, and even when we can, their closed form solution may be
so complicated that using it to obtain an image or to examine the structure of the system is impossible. For example, if we consider Schrodinger equation, i.e.,
We come to a three-term recursion relations, which work with it takes, at least, a little bit time to get a series solution[6]. For this
reason we use a change of variable such as or when we consider the orbital angular momentum[1], it will be
necessary to solve. As we can observe, working with this equation is tedious. In this paper, after introducing Clenshaw method, which is a kind of Spectral method, we try to solve some of such equations.