Abstract: This paper presents a new method which applies an
artificial bee colony algorithm (ABC) for capacitor placement in
distribution systems with an objective of improving the voltage profile
and reduction of power loss. The ABC algorithm is a new population
based meta heuristic approach inspired by intelligent foraging behavior
of honeybee swarm. The advantage of ABC algorithm is that
it does not require external parameters such as cross over rate and
mutation rate as in case of genetic algorithm and differential evolution
and it is hard to determine these parameters in prior. The other
advantage is that the global search ability in the algorithm is implemented
by introducing neighborhood source production mechanism
which is a similar to mutation process. To demonstrate the validity
of the proposed algorithm, computer simulations are carried out on
69-bus system and compared the results with the other approach
available in the literature. The proposed method has outperformed the
other methods in terms of the quality of solution and computational
efficiency.
Abstract: We investigated this hypothesis that arterial CO2 pressure (PaCO2) drives ventilation (V.E) with a time delay duringrecovery from short impulse-like exercise (10 s) with work load of 200 watts. V.E and end tidal CO2 pressure (PETCO2) were measured continuously during rest, warming up, exercise and recovery periods. PaCO2 was predicted (PaCO2 pre) from PETCO2 and tidal volume (VT). PETCO2 and PaCO2 pre peaked at 20 s of recovery. V.E increased and peaked at the end of exercise and then decreased during recovery; however, it peaked again at 30 s of recovery, which was 10 s later than the peak of PaCO2 pre. The relationship between V. E and PaCO2pre was not significant by using data of them obtained at the same time but was significant by using data of V.E obtained 10 s later for data of PaCO2 pre. The results support our hypothesis that PaCO2 drives V.E with a time delay.
Abstract: In this paper, multi-processors job shop scheduling problems are solved by a heuristic algorithm based on the hybrid of priority dispatching rules according to an ant colony optimization algorithm. The objective function is to minimize the makespan, i.e. total completion time, in which a simultanous presence of various kinds of ferons is allowed. By using the suitable hybrid of priority dispatching rules, the process of finding the best solution will be improved. Ant colony optimization algorithm, not only promote the ability of this proposed algorithm, but also decreases the total working time because of decreasing in setup times and modifying the working production line. Thus, the similar work has the same production lines. Other advantage of this algorithm is that the similar machines (not the same) can be considered. So, these machines are able to process a job with different processing and setup times. According to this capability and from this algorithm evaluation point of view, a number of test problems are solved and the associated results are analyzed. The results show a significant decrease in throughput time. It also shows that, this algorithm is able to recognize the bottleneck machine and to schedule jobs in an efficient way.
Abstract: Modern highly automated production systems faces
problems of reliability. Machine function reliability results in
changes of productivity rate and efficiency use of expensive
industrial facilities. Predicting of reliability has become an important
research and involves complex mathematical methods and
calculation. The reliability of high productivity technological
automatic machines that consists of complex mechanical, electrical
and electronic components is important. The failure of these units
results in major economic losses of production systems. The
reliability of transport and feeding systems for automatic
technological machines is also important, because failure of transport
leads to stops of technological machines. This paper presents
reliability engineering on the feeding system and its components for
transporting a complex shape parts to automatic machines. It also
discusses about the calculation of the reliability parameters of the
feeding unit by applying the probability theory. Equations produced
for calculating the limits of the geometrical sizes of feeders and the
probability of sticking the transported parts into the chute represents
the reliability of feeders as a function of its geometrical parameters.
Abstract: The acoustic and articulatory properties of fricative speech sounds are being studied using magnetic resonance imaging (MRI) and acoustic recordings from a single subject. Area functions were derived from a complete set of axial and coronal MR slices using two different methods: the Mermelstein technique and the Blum transform. Area functions derived from the two techniques were shown to differ significantly in some cases. Such differences will lead to different acoustic predictions and it is important to know which is the more accurate. The vocal tract acoustic transfer function (VTTF) was derived from these area functions for each fricative and compared with measured speech signals for the same fricative and same subject. The VTTFs for /f/ in two vowel contexts and the corresponding acoustic spectra are derived here; the Blum transform appears to show a better match between prediction and measurement than the Mermelstein technique.
Abstract: This study describes the relationship between motivation factors and academic performance among distance education students enrolled in a postgraduate nursing course. Students (n=96) participated in a survey that assesses student's motivational orientations from a cognitive perspective using a selfadministered questionnaire based on Pintrich-s Motivation Strategies for Learning Questionnaire (MLSQ). Results showed students- motivational factors are highest on task value (6.44, 0.71); followed by intrinsic goal orientation (6.20, 0.76), control beliefs (6.02, 0.89); extrinsic goal orientation (5.85, 1.13); self-efficacy for learning and performance (5.62, 0.84), and finally, test anxiety (4.21, 1.37). Weak positive correlations were found between academic performance and intrinsic goal orientation (r=0.13), extrinsic goal orientation (r=0.04), task value (r=0.09), control beliefs (r=0.02), and self-efficacy (r=0.05), while there was weak negative correlation with test anxiety (r=-0.04). Conclusions from the study indicate the need to focus on improving tasks and targeting intrinsic goal orientations of students to courses since these were positively correlated with academic performance and downplay the use of tests since these were negatively correlated with academic performance.
Abstract: In this article the investigation about installation heat
recovery steam generation (HRSG) on the exhaust of turbo generators of phases 2&3 at South Pars Gas Complex is presented.
The temperature of exhaust gas is approximately 665 degree centigrade, Installation of heat recovery boiler was simulated in
ThermoFlow 17.0.2 software, based on test operation data and the
equipments site operation conditions in Pars exclusive economical energy area, the affect of installation HRSG package on the available
gas turbine and its operation parameters, ambient temperature, the
exhaust temperatures steam flow rate were investigated. Base on the results recommended HRSG package should have the capacity for 98
ton per hour high pressure steam generation this refinery, by use of
exhaust of three gas turbines for each package in operation condition of each refinery at 30 degree centigrade. Besides saving energy this
project will be an Environment-Friendly project. The Payback Period
is estimated approximately 1.8 year, with considering Clean Development Mechanism.
Abstract: The COSvd Ciphers has been proposed by Filiol and others (2004). It is a strengthened version of COS stream cipher family denoted COSvd that has been adopted for at least one commercial standard. We propose a distinguish attack on this version, and prove that, it is distinguishable from a random stream. In the COSvd Cipher used one S-Box (10×8) on the final part of cipher. We focus on S-Box and use weakness this S-Box for distinguish attack. In addition, found a leak on HNLL that the sub s-boxes don-t select uniformly. We use this property for an Improve distinguish attack.
Abstract: The evolution of silica optical fiber strength aged in cetyltrimethylammonium chloride solution (CTAC) has been investigated. If the solution containing surfactants presents appreciable changes in physical and chemical properties at the critical micelle concentration (CMC), a non negligible mechanical behavior fiber change is observed for silica fiber aged in cationic surfactants as CTAC which can lead to optical fiber reliability questioning. The purpose of this work is to study the mechanical behavior of silica coated and naked optical fibers in contact with CTAC solution at different concentrations. Result analysis proves that the immersion in CTAC drastically decreases the fiber strength and specially near the CMC point. Beyond CMC point, a small increase of fiber strength is analyzed and commented.
Abstract: The development of Artificial Neural Networks
(ANNs) is usually a slow process in which the human expert has to
test several architectures until he finds the one that achieves best
results to solve a certain problem. This work presents a new
technique that uses Genetic Programming (GP) for automatically
generating ANNs. To do this, the GP algorithm had to be changed in
order to work with graph structures, so ANNs can be developed. This
technique also allows the obtaining of simplified networks that solve
the problem with a small group of neurons. In order to measure the
performance of the system and to compare the results with other
ANN development methods by means of Evolutionary Computation
(EC) techniques, several tests were performed with problems based
on some of the most used test databases. The results of those
comparisons show that the system achieves good results comparable
with the already existing techniques and, in most of the cases, they
worked better than those techniques.
Abstract: This paper presents a procedure for modeling and tuning the parameters of Thyristor Controlled Series Compensation (TCSC) controller in a multi-machine power system to improve transient stability. First a simple transfer function model of TCSC controller for stability improvement is developed and the parameters of the proposed controller are optimally tuned. Genetic algorithm (GA) is employed for the optimization of the parameter-constrained nonlinear optimization problem implemented in a simulation environment. By minimizing an objective function in which the oscillatory rotor angle deviations of the generators are involved, transient stability performance of the system is improved. The proposed TCSC controller is tested on a multi-machine system and the simulation results are presented. The nonlinear simulation results validate the effectiveness of proposed approach for transient stability improvement in a multimachine power system installed with a TCSC. The simulation results also show that the proposed TCSC controller is also effective in damping low frequency oscillations.
Abstract: Graph partitioning is a NP-hard problem with multiple
conflicting objectives. The graph partitioning should minimize the
inter-partition relationship while maximizing the intra-partition
relationship. Furthermore, the partition load should be evenly
distributed over the respective partitions. Therefore this is a multiobjective
optimization problem (MOO). One of the approaches to
MOO is Pareto optimization which has been used in this paper. The
proposed methods of this paper used to improve the performance are
injecting best solutions of previous runs into the first generation of
next runs and also storing the non-dominated set of previous
generations to combine with later generation's non-dominated set.
These improvements prevent the GA from getting stuck in the local
optima and increase the probability of finding more optimal
solutions. Finally, a simulation research is carried out to investigate
the effectiveness of the proposed algorithm. The simulation results
confirm the effectiveness of the proposed method.
Abstract: Trauma in early life is widely regarded as a cause for
adult mental health problems. This study explores the role of
secondary trauma on later functioning in a sample of 359 university
students enrolled in undergraduate psychology classes in the United
States. Participants were initially divided into four groups based on
1) having directly experienced trauma (assaultive violence), 2)
having directly experienced trauma and secondary traumatization
through the unanticipated death of a close friend or family member
or witnessing of an injury or shocking even), 3) having no
experience of direct trauma but having experienced indirect trauma
(secondary trauma), or 4) reporting no exposure. Participants
completed a battery of measures on concepts associated with
psychological functioning which included measures of
psychological well-being, problem solving, coping and resiliency.
Findings discuss differences in psychological functioning and
resilience based on participants who experienced secondary
traumatization and assaultive violence versus secondary
traumatization alone.
Abstract: A novel physico-chemical route to produce few layer graphene nanoribbons with atomically smooth edges is reported, via acid treatment (H2SO4:HNO3) followed by characteristic thermal shock processes involving extremely cold substances. Samples were studied by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), Raman spectroscopy and X-ray photoelectron spectroscopy. This method demonstrates the importance of having the nanotubes open ended for an efficient uniform unzipping along the nanotube axis. The average dimensions of these nanoribbons are approximately ca. 210 nm wide and consist of few layers, as observed by transmission electron microscopy. The produced nanoribbons exhibit different chiralities, as observed by high resolution transmission electron microscopy. This method is able to provide graphene nanoribbons with atomically smooth edges which could be used in various applications including sensors, gas adsorption materials, composite fillers, among others.
Abstract: One of the main issues in Computer Vision is to extract the movement of one or several points or objects of interest in an image or video sequence to conduct any kind of study or control process. Different techniques to solve this problem have been applied in numerous areas such as surveillance systems, analysis of traffic, motion capture, image compression, navigation systems and others, where the specific characteristics of each scenario determine the approximation to the problem. This paper puts forward a Computer Vision based algorithm to analyze fish trajectories in high turbulence conditions in artificial structures called vertical slot fishways, designed to allow the upstream migration of fish through obstructions in rivers. The suggested algorithm calculates the position of the fish at every instant starting from images recorded with a camera and using neural networks to execute fish detection on images. Different laboratory tests have been carried out in a full scale fishway model and with living fishes, allowing the reconstruction of the fish trajectory and the measurement of velocities and accelerations of the fish. These data can provide useful information to design more effective vertical slot fishways.
Abstract: Vibration characteristics of subcooled flow boiling on
thin and long structures such as a heating rod were recently
investigated by the author. The results show that the intensity of the
subcooled boiling-induced vibration (SBIV) was influenced strongly
by the conditions of the subcooling temperature, linear power density
and flow velocity. Implosive bubble formation and collapse are the
main nature of subcooled boiling, and their behaviors are the only
sources to originate from SBIV. Therefore, in order to explain the
phenomenon of SBIV, it is essential to obtain reliable information
about bubble behavior in subcooled boiling conditions. This was
investigated at different conditions of coolant subcooling
temperatures of 25 to 75°C, coolant flow velocities of 0.16 to
0.53m/s, and linear power densities of 100 to 600 W/cm. High speed
photography at 13,500 frames per second was performed at these
conditions. The results show that even at the highest subcooling
condition, the absolute majority of bubbles collapse very close to the
surface after detaching from the heating surface. Based on these
observations, a simple model of surface tension and momentum
change is introduced to offer a rough quantitative estimate of the
force exerted on the heating surface during the bubble ebullition. The
formation of a typical bubble in subcooled boiling is predicted to
exert an excitation force in the order of 10-4 N.
Abstract: This paper presents a new technique for generating sets of synthetic classifiers to evaluate abstract-level combination methods. The sets differ in terms of both recognition rates of the individual classifiers and degree of similarity. For this purpose, each abstract-level classifier is considered as a random variable producing one class label as the output for an input pattern. From the initial set of classifiers, new slightly different sets are generated by applying specific operators, which are defined at the purpose. Finally, the sets of synthetic classifiers have been used to estimate the performance of combination methods for abstract-level classifiers. The experimental results demonstrate the effectiveness of the proposed approach.
Abstract: Presence of phytosterol compound in Durian seed
(Durio zibethinus) or known as King of fruits has been discovered
from screening work using reagent test. Further analysis work has
been carried out using mass spectrometer in order to support the
priliminary finding. Isolation and purification of the major
phytosterol has been carried out using an open column
chromatography. The separation was monitored using thin layer
chromatography (TLC). Major isolated compounds and purified
phytosterol were identified using mass spectrometer and nuclear
magnetic resonance (NMR). This novel finding could promote
utilization of durian seeds as a functional ingredient in food products
through production of standardized extract based on phytosterol
content.
Abstract: Axial Flux Permanent Magnet (AFPM) Machines require effective cooling due to their high power density. The detrimental effects of overheating such as degradation of the insulation materials, magnets demagnetization, and increase of Joule losses are well known. This paper describes the CFD simulations performed on a test rig model of an air cooled Axial Flux Permanent Magnet (AFPM) generator built at Durham University to identify the temperatures and heat transfer coefficient on the stator. The Reynolds Averaged Navier-Stokes and the Energy equations are solved and the flow pattern and heat transfer developing inside the machine are described. The Nusselt number on the stator surfaces has been found. The dependency of the heat transfer on the flow field is described temperature field obtained. Tests on an experimental are undergoing in order to validate the CFD results.
Abstract: This study investigated the removal efficiency of electrokinetic remediation of copper-contaminated soil at different combinations of enhancement reagents used as anolyte and catholyte. Sodium hydroxide (at 0.1, 0.5, and 1.0 M concentrations) and distilled water were used as anolyte, while lactic acid (at 0.01, 0.1, and 0.5 M concentrations), ammonium citrate (also at 0.01, 0.1, and 0.5 M concentrations) and distilled water were used as catholyte. A continuous voltage application (1.0 VDC/cm) was employed for 240 hours for each experiment. The copper content of the catholyte was determined at the end of the 240-hour period. Optimization was carried out with a Response Surface Methodology - Optimal Design, including F test, and multiple comparison method, to determine which pair of anolyte-catholyte was the most significant for the removal efficiency. "1.0 M NaOH" was found to be the most significant anolyte while it was established that lactic acid was the most significant type of catholyte to be used for the most successful electrokinetic experiments. Concentrations of lactic acid should be at the range of 0.1 M to 0.5 M to achieve maximum percent removal values.