Abstract: In this paper, we propose effective system for digital music retrieval. We divided proposed system into Client and Server. Client part consists of pre-processing and Content-based feature extraction stages. In pre-processing stage, we minimized Time code Gap that is occurred among same music contents. As content-based feature, first-order differentiated MFCC were used. These presented approximately envelop of music feature sequences. Server part included Music Server and Music Matching stage. Extracted features from 1,000 digital music files were stored in Music Server. In Music Matching stage, we found retrieval result through similarity measure by DTW. In experiment, we used 450 queries. These were made by mixing different compression standards and sound qualities from 50 digital music files. Retrieval accurate indicated 97% and retrieval time was average 15ms in every single query. Out experiment proved that proposed system is effective in retrieve digital music and robust at various user environments of web.
Abstract: A numerical investigation of surface heat transfer
characteristics of turbulent air flows in different parallel plate
grooved channels is performed using CFD code. The results are
obtained for Reynolds number ranging from 10,000 to 30,000 and for
arc-shaped and rectangular grooved channels. The influence of
different geometric parameters of dimples as well as the number of
them and the geometric and thermophysical properties of channel
walls are studied. It is found that there exists an optimum value for
depth of dimples in which the largest wall heat flux can be achieved.
Also, the results show a critical value for the ratio of wall thermal
conductivity to the one of fluid in which the dependence of wall heat
flux to this ratio almost vanishes. In most cases examined, heat
transfer enhancement is larger for arc-shaped grooved channels than
rectangular ones.
Abstract: In order to study the effect of plant density and
competition of wheat with field bindweed (Convolvulus arvensis) on
yield and agronomical properties of wheat(Triticum Sativum) in
irrigated conditions, a factorial experiment as the base of complete
randomize block design in three replication was conducted at the
field of Kamalvand in khoramabad (Lorestan) region of Iran during
2008-2009. Three plant density (Factor A=200, 230 and 260kg/ha)
three cultivar (Factor B=Bahar,Pishtaz and Alvand) and weed control
(Factor C= control and no control of weeds)were assigned in
experiment. Results show that: Plant density had significant effect
(statistically) on seed yield, 1000 seed weight, weed density and dry
weight of weeds, seed yield and harvest index had been meaningful
effect for cultivars. The interaction between plant density and
cultivars for weed density, seed yield, thousand seed weight and
harvest index were significant. 260 kg/ha (plant density) of wheat had
more effect on increasing of seed yield in Bahar cultivar wheat in
khoramabad region of Iran.
Abstract: Abrasive waterjet is a novel machining process capable of processing wide range of hard-to-machine materials. This research addresses modeling and optimization of the process parameters for this machining technique. To model the process a set of experimental data has been used to evaluate the effects of various parameter settings in cutting 6063-T6 aluminum alloy. The process variables considered here include nozzle diameter, jet traverse rate, jet pressure and abrasive flow rate. Depth of cut, as one of the most important output characteristics, has been evaluated based on different parameter settings. The Taguchi method and regression modeling are used in order to establish the relationships between input and output parameters. The adequacy of the model is evaluated using analysis of variance (ANOVA) technique. The pairwise effects of process parameters settings on process response outputs are also shown graphically. The proposed model is then embedded into a Simulated Annealing algorithm to optimize the process parameters. The optimization is carried out for any desired values of depth of cut. The objective is to determine proper levels of process parameters in order to obtain a certain level of depth of cut. Computational results demonstrate that the proposed solution procedure is quite effective in solving such multi-variable problems.
Abstract: In this work we investigated the behavior of methane
hydrates dispersed in crude oils from different fields at temperatures
below 0°C. In case of crude oil emulsion the size of water droplets is
in the range of 50e100"m. The size of hydrate particles formed from
droplets is the same. The self-preservation is not expected in this
field. However, the self-preservation of hydrates with the size of
particles 24±18"m (electron microscopy data) in suspensions is
observed. Similar results were obtained for four different kinds of
crude oil and model system such as asphaltenes, resins and wax in ndecane.
This result can allow developing effective methods to prevent
the formation and elimination of gas-hydrate plugs in pipelines under
low temperature conditions (e. g. in Eastern Siberia). There is a
prospective to use experiment results for working out the technology
of associated petroleum gas recovery.
Abstract: The paper presents the method developed to assess
rating points of objects with qualitative indexes. The novelty of the
method lies in the fact that the authors use linguistic scales that allow
to formalize the values of the indexes with the help of fuzzy sets. As
a result it is possible to operate correctly with dissimilar indexes on
the unified basis and to get stable final results. The obtained rating
points are used in decision making based on fuzzy expert opinions.
Abstract: The photoplethysmogram (PPG) is the pulsatile waveform
produced by the pulse oximeter, which is widely used for
monitoring arterial oxygen saturation in patients. Various methods
for extracting the breathing rate from the PPG waveform have been
compared using a consistent data set, and a novel technique using
autoregressive modelling is presented. This novel technique is shown
to outperform the existing techniques, with a mean error in breathing
rate of 0.04 breaths per minute.
Abstract: Visual inputs are one of the key sources from which
humans perceive the environment and 'understand' what is
happening. Artificial systems perceive the visual inputs as digital
images. The images need to be processed and analysed. Within the
human brain, processing of visual inputs and subsequent
development of perception is one of its major functionalities. In this
paper we present part of our research project, which aims at the
development of an artificial model for visual perception (or
'understanding') based on the human perceptive and cognitive
systems. We propose a new model for perception from visual inputs
and a way of understaning or interpreting images using the model.
We demonstrate the implementation and use of the model with a real
image data set.
Abstract: Indium-tin oxide films are deposited by low plasma
temperature RF sputtering on highly flexible modification of glycol
polyethyleneterephtalate substrates. The produced layers are
characterized with transparency over 82 % and sheet resistance of
86.9 Ω/square. The film’s conductivity was further improved by
additional UV illumination from light source (365 nm), having power
of 250 W. The influence of the UV exposure dose on the structural
and electro-optical properties of ITO was investigated. It was
established that the optimum time of illumination is 10 minutes and
further UV treatment leads to polymer substrates degradation.
Structural and bonds type analysis show that at longer treatment
carbon atoms release and diffuse into ITO films, which worsen their
electrical behavior. For the optimum UV dose the minimum sheet
resistance was measured to be 19.2 Ω/square, and the maximum
transparency remained almost unchanged – above 82 %.
Abstract: High voltage generators are being subject to higher
voltage rating and are being designed to operate in harsh conditions.
Stator windings are the main component of generators in which
Electrical, magnetical and thermal stresses remain major failures for
insulation degradation accelerated aging. A large number of
generators failed due to stator winding problems, mainly insulation
deterioration. Insulation degradation assessment plays vital role in the
asset life management. Mostly the stator failure is catastrophic
causing significant damage to the plant. Other than generation loss,
stator failure involves heavy repair or replacement cost. Electro
thermal analysis is the main characteristic for improvement design of
stator slot-s insulation. Dielectric parameters such as insulation
thickness, spacing, material types, geometry of winding and slot are
major design consideration. A very powerful method available to
analyze electro thermal performance is Finite Element Method
(FEM) which is used in this paper. The analysis of various stator coil
and slot configurations are used to design the better dielectric system
to reduce electrical and thermal stresses in order to increase the
power of generator in the same volume of core. This paper describes
the process used to perform classical design and improvement
analysis of stator slot-s insulation.
Abstract: Several methods are available for weight and shape
optimization of structures, among which Evolutionary Structural
Optimization (ESO) is one of the most widely used methods. In ESO,
however, the optimization criterion is completely case-dependent.
Moreover, only the improving solutions are accepted during the
search. In this paper a Simulated Annealing (SA) algorithm is used
for structural optimization problem. This algorithm differs from other
random search methods by accepting non-improving solutions. The
implementation of SA algorithm is done through reducing the
number of finite element analyses (function evaluations).
Computational results show that SA can efficiently and effectively
solve such optimization problems within short search time.
Abstract: The paper deals with hydrodynamics of liquid-gas
layers under gas streaming through liquid layer on perforated plates
in column apparatuses. The plates with large apertures have been
investigated especially. It was shown that hydrodynamic regularities
for these plates are essentially different from known laws for foam
forming on fine-perforated plates. Main regularities of liquid-gas
interaction on plates with large apertures have been established.
Abstract: Through the course of this paper we outline how
mobile Business Intelligence (m-BI) can help businesses to work
smarter and to improve their agility. When we analyze the industry
from the usage perspective or how interaction with the enterprise BI
system happens via mobile devices, we may easily understand that
there are two major types of mobile BI: passive and active. Active
mobile BI gives provisions for users to interact with the BI systems
on-the-fly. Active mobile business intelligence often works as a
combination of both “push and pull" techniques. Some mistakes were
done in the up-to-day progress of mobile technologies and mobile BI,
as well as some problems that still have to be resolved. We discussed
in the paper rather broadly.
Abstract: Researchers have been applying artificial/ computational intelligence (AI/CI) methods to computer games. In this research field, further researchesare required to compare AI/CI methods with respect to each game application. In thispaper, we report our experimental result on the comparison of evolution strategy, genetic algorithm and their hybrids, applied to evolving controller agents for MarioAI. GA revealed its advantage in our experiment, whereas the expected ability of ES in exploiting (fine-tuning) solutions was not clearly observed. The blend crossover operator and the mutation operator of GA might contribute well to explore the vast search space.
Abstract: Biomechanical properties of infantile aorta in vitro in
cases of different standard anastomoses: end-to-end (ETE), extended
anastomosis end-to-end (EETE) and subclavian flap aortoplasty
(SFA) used for surgical correction of coarctation were analyzed to
detect the influence of the method on the biomechanics of infantile
aorta and possible changes in haemodinamics. 10 specimens of native
aorta, 3 specimens with ETE, 4 EEET and 3 SFA were investigated.
The experiments showed a non-linear relationship between stress and
strain in the infantile aorta, the modulus of elasticity of the aortic wall
increased with the increase of inner pressure. In the case of
anastomosis end-to-end the modulus was almost constant, relevant to
the modulus of elasticity of the aorta with the inner pressure 100-120
mmHg. The anastomoses EETE and SFA showed elastic properties
closer to native aorta, the stiffness of ETE did not change with the
changes in inner pressure.
Abstract: Bacterial molecular chaperone DnaK plays an essential role in protein folding, stress response and transmembrane targeting of proteins. DnaKs from many bacterial species, including Escherichia coli, Salmonella typhimurium and Haemophilus infleunzae are the molecular targets for the insect-derived antimicrobial peptide pyrrhocoricin. Pyrrhocoricin-like peptides bind in the substrate recognition tunnel. Despite the high degree of crossspecies sequence conservation in the substrate-binding tunnel, some bacteria are not sensitive to pyrrhocoricin. This work addresses the molecular mechanism of resistance of Helicobacter pylori DnaK to pyrrhocoricin. Homology modelling, structural and sequence analysis identify a single aminoacid substitution at the interface between the lid and the β-sandwich subdomains of the DnaK substrate-binding domain as the major determinant for its resistance.
Abstract: The Ramon preparation is received from a plant; it is destined for external treatment of inflammations in post-surgery period. The Ramon is a biogenic immune stimulator accelerating metabolism, contributing to improvement of blood indexes, having general tonic, anti-inflammatory and bactericidal effect.
Abstract: Tea is a widely consumed beverage that contains many components. Caffeine belongs to this group of components called alkaloids contain nitrogen. In this study caffeine contents of three types of Turkish teas are determined by using extraction method. After condensation process, residue of caffeine and oil are obtained with evaporation. The oil which is in the residue is removed by hot water. Extraction process performed by using chloroform and the crude caffeine is obtained. From the results of experiments, caffeine contents are found in black tea, green tea and earl grey tea as 3.57±0.43%, 3.11±0.02%, 4.29±0.27%, respectively. Caffeine contents which are found in 1, 5 and 10 cups of tea are calculated. Furthermore, the daily intake of caffeine from black teas that affects human health is investigated.
Abstract: This paper presents a silicon controller rectifier (SCR)
based ESD protection circuit for IC. The proposed ESD protection
circuit has low trigger voltage and high holding voltage compared with
conventional SCR ESD protection circuit. Electrical characteristics of
the proposed ESD protection circuit are simulated and analyzed using
TCAD simulator. The proposed ESD protection circuit verified
effective low voltage ESD characteristics with low trigger voltage and
high holding voltage.
Abstract: S-Curves are commonly used in technology forecasting. They show the paths of product performance in relation to time or investment in R&D. It is a useful tool to describe the inflection points and the limit of improvement of a technology. Companies use this information to base their innovation strategies.
However inadequate use and some limitations of this technique lead
to problems in decision making. In this paper first technology
forecasting and its importance for company level strategies will be
discussed. Secondly the S-Curve and its place among other
forecasting techniques will be introduced. Thirdly its use in
technology forecasting will be discussed based on its advantages,
disadvantages and limitations. Finally an application of S-curve on
3D TV technology using patent data will also be presented and the
results will be discussed.