Abstract: This paper reports the results of an experimental study
conducted to characterise the gas-liquid multiphase flows
experienced within a vertical riser transporting a range of gas-liquid
flow rates. The scale experiments were performed using an
air/silicone oil mixture within a 6 m long riser. The superficial air
velocities studied ranged from 0.047 to 2.836 m/ s, whilst
maintaining a liquid superficial velocity at 0.047 m/ s. Measurements
of the mean cross-sectional and time average radial void fraction
were obtained using a wire mesh sensor (WMS). The data were
recorded at an acquisition frequency of 1000 Hz over an interval of
60 seconds. For the range of flow conditions studied, the average
void fraction was observed to vary between 0.1 and 0.9. An analysis
of the data collected concluded that the observed void fraction was
strongly affected by the superficial gas velocity, whereby the higher
the superficial gas velocity, the higher was the observed average void
fraction. The average void fraction distributions observed were in
good agreement with the results obtained by other researchers. When
the air-silicone oil flows were fully developed reasonably symmetric
profiles were observed, with the shape of the symmetry profile being
strongly dependent on the superficial gas velocity.
Abstract: This paper describes an automated event detection and location system for water distribution pipelines which is based upon low-cost sensor technology and signature analysis by an Artificial
Neural Network (ANN). The development of a low cost failure sensor which measures the opacity or cloudiness of the local water
flow has been designed, developed and validated, and an ANN based system is then described which uses time series data produced by
sensors to construct an empirical model for time series prediction and
classification of events. These two components have been installed,
tested and verified in an experimental site in a UK water distribution
system. Verification of the system has been achieved from a series of
simulated burst trials which have provided real data sets. It is concluded that the system has potential in water distribution network
management.
Abstract: A total of 33,680 nuclear power plants (NPPs) workers were monitored and recorded from 1990 to 2007. According to the record, the average individual radiation dose has been decreasing continually from it 3.20 mSv/man in 1990 to 1.12 mSv/man at the end of 2007. After the International Commission on Radiological Protection (ICRP) 60 recommendation was generalized in South Korea, no nuclear power plant workers received above 20 mSv radiation, and the numbers of relatively highly exposed workers have been decreasing continuously. The age distribution of radiation workers in nuclear power plants was composed of mainly 20-30- year-olds (83%) for 1990 ~ 1994 and 30-40-year-olds (75%) for 2003 ~ 2007. The difference in individual average dose by age was not significant. Most (77%) of NPP radiation exposures from 1990 to 2007 occurred mostly during the refueling period. With regard to exposure type, the majority of exposures were external exposures, representing 95% of the total exposures, while internal exposures represented only 5%. External effective dose was affected mainly by gamma radiation exposure, with an insignificant amount of neutron exposure. As for internal effective dose, tritium (3H) in the pressurized heavy water reactor (PHWR) was the biggest cause of exposure.
Abstract: In this paper, a multi-agent robot system is presented. The system consists of four robots. The developed robots are able to automatically enter and patrol a harmful environment, such as the building infected with virus or the factory with leaking hazardous gas. Further, every robot is able to perform obstacle avoidance and search for the victims. Several operation modes are designed: remote control, obstacle avoidance, automatic searching, and so on.
Abstract: An electronic portal image device (EPID) has become
a method of patient-specific IMRT dose verification for radiotherapy.
Research studies have focused on pre and post-treatment verification,
however, there are currently no interventional procedures using EPID
dosimetry that measure the dose in real time as a mechanism to
ensure that overdoses do not occur and underdoses are detected as
soon as is practically possible. As a result, an EPID-based real time
dose verification system for dynamic IMRT was developed and was
implemented with MATLAB/Simulink. The EPID image acquisition
was set to continuous acquisition mode at 1.4 images per second. The
system defined the time constraint gap, or execution gap at the image
acquisition time, so that every calculation must be completed before
the next image capture is completed. In addition, the
Abstract: This paper presents the fundamentals of Origami engineering and its application in nowadays as well as future industry. Several main cores of mathematical approaches such as Huzita- Hatori axioms, Maekawa and Kawasaki-s theorems are introduced briefly. Meanwhile flaps and circle packing by Robert Lang is explained to make understood the underlying principles in designing crease pattern. Rigid origami and its corrugation patterns which are potentially applicable for creating transformable or temporary spaces is discussed to show the transition of origami from paper to thick material. Moreover, some innovative applications of origami such as eyeglass, origami stent and high tech origami based on mentioned theories and principles are showcased in section III; while some updated origami technology such as Vacuumatics, self-folding of polymer sheets and programmable matter folding which could greatlyenhance origami structureare demonstrated in Section IV to offer more insight in future origami.
Abstract: Electro-optical devices are increasingly used for
military sea-, land- and air applications to detect, recognize and track
objects. Typically, these devices produce video information that is
presented to an operator. However, with increasing availability of
electro-optical devices the data volume is becoming very large,
creating a rising need for automated analysis. In a military setting,
this typically involves detecting and recognizing objects at a large
distance, i.e. when they are difficult to distinguish from background
and noise. One may consider combining multiple images from a
video stream into a single enhanced image that provides more
information for the operator. In this paper we investigate a simple
algorithm to enhance simulated images from a military context and
investigate how the enhancement is affected by various types of
disturbance.
Abstract: Green- spaces might be very attractive, but
where are the economic benefits? What value do nature and
landscape have for us? What difference will it make to jobs,
health and the economic strength of areas struggling with
deprivation and social problems? [1].There is a need to consider
green spaces from a different perspective. Green planning is not just
about flora and fauna, but also about planning for economic benefits
[2]. It is worth trying to quantify the value of green spaces since
nature and landscape are crucially important to our quality of life and
sustainable development. The reality, however, is that urban
development often takes place at the expense of green spaces.
Urbanization is an ongoing process throughout the world; however,
hyper-urbanization without environmental planning is destructive,
not constructive [3]. Urban spaces are believed to be more valuable
than other land uses, particular green areas, simply because of the
market value connected to urban spaces. However, attractive
landscapes can help raise the quality and value of the urban market
even more. In order to reach these objectives of integrated planning,
the Green-Value-Gap needs to be bridged. Economists have to
understand the concept of Green-Planning and the spinoffs, and
Environmentalists have to understand the importance of urban
economic development and the benefits thereof to green planning. An
interface between Environmental Management, Economic
Development and sustainable Spatial Planning are needed to bridge
the Green-Value-Gap.
Abstract: Computed tomography (CT) dosimetry normally uses
an ionization chamber 100 mm long to estimate the computed
tomography dose index (CTDI), however some reports have already
indicated that small devices could replace the long ion chamber to
improve quality assurance procedures in CT dosimetry. This paper
presents a novel dosimetry system based in a commercial
phototransistor evaluated for CT dosimetry. Three detector
configurations were developed for this system: with a single, two and
four devices. Dose profile measurements were obtained with them
and their angular response were evaluated. The results showed that
the novel dosimetry system with the phototransistor could be an
alternative for CT dosimetry. It allows to obtain the CT dose profile
in details and also to estimate the CTDI in longer length than the
100 mm pencil chamber. The angular response showed that the one
device detector configuration is the most adequate among the three
configurations analyzed in this study.
Abstract: The result of process of territory-s development is the territory-s state of development (TSoD), which is pointed towards the provision and improvement of people-s life conditions. The authors offer to measure the TSoD according to their own developed model. Using the available statistical data regarding the values of model-s elements, the authors empirically show which element mainly determines the TSoD. The findings of the research showed that the key elements of the TSoD are the “Material welfare of people" and “People-s health". Performing a deeper statistical analysis of correlation between these elements, it turned out that it is not so necessary for a country to be bent on trying to increase the material growth of a territory, because a relatively high index of life expectancy at birth could be ensured also by much more modest material resources. On the other hand, the economical feedback of longer lifespan within countries with lower material performance is also relatively low.
Abstract: In this paper we propose a blind algorithm for peakto- average power ratio (PAPR) reduction in OFDM systems, based on selected mapping (SLM) algorithm as a distortionless method. The main drawback of the conventional SLM technique is the need for transmission of several side information bits, for each data block, which results in loss in data rate transmission. In the proposed method some special number of carriers in the OFDM frame is reserved to be rotated with one of the possible phases according to the number of phase sequence blocks in SLM algorithm. Reserving some limited number of carriers wont effect the reduction in PAPR of OFDM signal. Simulation results show using ML criteria at the receiver will lead to the same system-performance as the conventional SLM algorithm, while there is no need to send any side information to the receiver.
Abstract: Autoregressive Moving average (ARMA) is a parametric based method of signal representation. It is suitable for problems in which the signal can be modeled by explicit known source functions with a few adjustable parameters. Various methods have been suggested for the coefficients determination among which are Prony, Pade, Autocorrelation, Covariance and most recently, the use of Artificial Neural Network technique. In this paper, the method of using Artificial Neural network (ANN) technique is compared with some known and widely acceptable techniques. The comparisons is entirely based on the value of the coefficients obtained. Result obtained shows that the use of ANN also gives accurate in computing the coefficients of an ARMA system.
Abstract: A direct downconversion receiver implemented in 0.13 μm 1P8M process is presented. The circuit is formed by a single-end LNA, an active balun for conversion into balanced mode, a quadrature double-balanced passive switch mixer and a quadrature voltage-controlled oscillator. The receiver operates in the 2.4 GHz ISM band and complies with IEEE 802.15.4 (ZigBee) specifications. The circuit exhibits a very low noise figure of only 2.27 dB and dissipates only 14.6 mW with a 1.2 V supply voltage and is hence suitable for low-power applications.
Abstract: In this study, the two dimensional heat conduction
problem for the dry friction clutch disc is modeled mathematically
analysis and is solved numerically using finite element method, to
determine the temperature field when band contacts occurs between
the rubbing surfaces during the operation of an automotive clutch.
Temperature calculation have been made for contact area of different
band width and the results obtained compared with these attained
when complete contact occurs. Furthermore, the effects of slipping
time and sliding velocity function are investigated as well. Both
single and repeated engagements made at regular interval are
considered.
Abstract: The operational behavior of a six-phase squirrel cage
induction machine with faulted stator terminals is presented in this
paper. The study is carried out using the derived mathematical model
of the machine in the arbitrary reference frame. Tests are conducted
on a 1 kW experimental machine.
Steady-state and dynamic performance are analyzed for the
machine unloaded and loaded conditions. The results shows that with
one of the stator phases experiencing either an open- circuit or short
circuit fault the machine still produces starting torque, albeit the
running performance is significantly derated.
Abstract: A study of various turbulent inflow generation methods
was performed to compare their relative effectiveness for LES
computations of turbulent boundary layers. This study confirmed
the quality of the turbulent information produced by the family of
recycling and rescaling methods which take information from within
the computational domain. Furthermore, more general inflow methods
also proved applicable to such simulations, with a precursor-like
inflow and a random inflow augmented with forcing planes showing
promising results.
Abstract: The dilute acid pretreatment and enzymatic
saccharification of lignocellulosic substrate, cogon grass (Imperata
cylindrical, L.) was optimized prior ethanol fermentation using
simultaneous saccharification and fermentation (SSF) method. The
optimum pretreatment conditions, temperature, sulfuric acid
concentration, and reaction time were evaluated by determining the
maximum sugar yield at constant enzyme loading. Cogon grass, at
10% w/v substrate loading, has optimum pretreatment conditions of
126°C, 0.6% v/v H2SO4, and 20min reaction time. These
pretreatment conditions were used to optimize enzymatic
saccharification using different enzyme combinations. The maximum
saccharification yield of 36.68mg/mL (71.29% reducing sugar) was
obtained using 25FPU/g-cellulose cellulase complex combined with
1.1% w/w of cellobiase, ß-glucosidase, and 0.225% w/w of
hemicellulase complex, after 96 hours of saccharification. Using the
optimum pretreatment and saccharification conditions, SSF of treated
substrates was done at 37°C for 120 hours using industrial yeast
strain HBY3, Saccharomyces cerevisiae. The ethanol yield for cogon
grass at 4% w/w loading was 9.11g/L with 5.74mg/mL total residual
sugar.
Abstract: A nonlinear optimal controller with a fuzzy gain
scheduler has been designed and applied to a Line-Of-Sight (LOS)
stabilization system. Use of Linear Quadratic Regulator (LQR)
theory is an optimal and simple manner of solving many control
engineering problems. However, this method cannot be utilized
directly for multigimbal LOS systems since they are nonlinear in
nature. To adapt LQ controllers to nonlinear systems at least a
linearization of the model plant is required. When the linearized
model is only valid within the vicinity of an operating point a gain
scheduler is required. Therefore, a Takagi-Sugeno Fuzzy Inference
System gain scheduler has been implemented, which keeps the
asymptotic stability performance provided by the optimal feedback
gain approach. The simulation results illustrate that the proposed
controller is capable of overcoming disturbances and maintaining a
satisfactory tracking performance.
Abstract: Paper presents knowledge about types of test in area
of materials properties of selected methods of rapid prototyping
technologies. In today used rapid prototyping technologies for
production of models and final parts are used materials in initial state
as solid, liquid or powder material structure. In solid state are used
various forms such as pellets, wire or laminates. Basic range
materials include paper, nylon, wax, resins, metals and ceramics. In
Fused Deposition Modeling (FDM) rapid prototyping technology are
mainly used as basic materials ABS (Acrylonitrile Butadiene
Styrene), polyamide, polycarbonate, polyethylene and polypropylene.
For advanced FDM applications are used special materials as silicon
nitrate, PZT (Piezoceramic Material - Lead Zirconate Titanate),
aluminium oxide, hydroxypatite and stainless steel.
Abstract: Application of pesticides in the paddy fields has
deleterious effects on non-target organisms including cyanobacteria
which are photosynthesizing and nitrogen fixing micro-organisms
contributing significantly towards soil fertility and crop yield.
Pesticide contamination in the paddy fields has manifested into a
serious global environmental concern. To study the effect of one such
pesticide, three cyanobacterial strains; Anabaena fertilissima,
Aulosira fertilissima and Westiellopsis prolifica were selected for
their stress responses to an Organochlorine insecticide - 6, 7, 8, 9, 10,
10-hexachloro-1, 5, 5a, 6, 9, 9a-hexahydro-6, 9-methano-2, 4, 3-
benzodioxathiepine-3-oxide, with reference to their photosynthesic
pigments-chlorophyll-a and carotenoids as well as accessory
pigments-phycobiliproteins (phycocyanin, allophycocyanin and
phycoerythrin), stress induced biochemical metabolites like
carbohydrates, proteins, amino acids, phenols and enzymes-nitrate
reductase, glutamine synthetase and succinate dehydrogenase. All
the three cyanobacterial strains were adversely affected by the
insecticide doses and inhibition was dose dependent. Reduction in
photosynthetic and accessory pigments, metabolites, nitrogen fixing
and respiratory enzymes of the test organisms were accompanied
with an initial increase in their total protein at lower Organochlorine
doses. On the other hand, increased amount of phenols in all the
insecticide treated concentrations was indicative of stressed activities
of the organisms.