Abstract: A reliable estimate of the average bond stress within
the anchorage of steel reinforcing bars in tension is critically
important for the design of reinforced concrete member. This paper
describes part of a recently completed experimental research program
in the Centre for Infrastructure Engineering and Safety (CIES) at the
University of New South Wales, Sydney, Australia aimed at
assessing the effects of different factors on the anchorage
requirements of modern high strength steel reinforcing bars. The
study found that an increase in the anchorage length and bar diameter
generally leads to a reduction of the average ultimate bond stress. By
the extension of a well established analytical model of bond and
anchorage, it is shown here that the differences in the average
ultimate bond stress for different anchorage lengths is associated with
the variable degree of plastic deformation in the tensile zone of the
concrete surrounding the bar.
Abstract: A low cost Short Message System (SMS) based Home security system equipped with motion, smoke, temperature, humidity and light sensors has been studied and tested. The sensors are controlled by a microprocessor PIC 18F4520 through the SMS having password protection code for the secure operation. The user is able to switch light and the appliances and get instant feedback. Also in cases of emergencies such as fire or robbery the system will send alert message to occupant and relevant civil authorities. The operation of the home security has been tested on Vodafone- Fiji network and Digicel Fiji Network for emergency and feedback responses for 25 samples. The experiment showed that it takes about 8-10s for the security system to respond in case of emergency. It takes about 18-22s for the occupant to switch and monitor lights and appliances and then get feedback depending upon the network traffic.
Abstract: The development of the poultry industry in Albania is mainly based on the existence of intensive modern farms with huge capacities, which often are mixed with other forms. Colibacillosis is commonly displayed regardless of the type of breeding, delivering high mortality in poultry industry. The mechanisms with which pathogen enterobacters are able to cause the infection in poultry are not yet clear. The routine diagnose in the field, followed by isolation of E. coli and species of Salmonella genres in reference laboratories cannot lead in classification or full recognition of circulative strains in a territory, if it is not performed a differentiation among the present microorganisms in intensive farms and those in rural areas. In this study were isolated 1.496 strains of E. coli and 378 Salmonella spp. This study, presents distribution of poultry pathogenosity of E.coli and Salmonella spp., based on the usage of innovative diagnostic methods.
Abstract: The distance protection mainly the impedance relay which is considered as the main protection for transmission lines can be subjected to impedance measurement error which is, mainly, due to the fault resistance and to the power fluctuation. Thus, the impedance relay may not operate for a short circuit at the far end of the protected line (case of the under reach) or operates for a fault beyond its protected zone (case of overreach). In this paper, an approach to fault detection by a distance protection, which distinguishes between the faulty conditions and the effect of overload operation mode, has been developed. This approach is based on the symmetrical components; mainly the negative sequence, and it is taking into account both the effect of fault resistance and the overload situation which both have an effect upon the reliability of the protection in terms of dependability for the former and security for the latter.
Abstract: The Brazilian Agricultural Products Wholesale Market fits well as example of residues generating system, reaching 750 metric tons per month of total residues, from which 600 metric tons are organic material and 150 metric tons are recyclable materials. Organic material is basically composed of fruit, vegetables and flowers leftovers from the products commercialization. The recyclable compounds are generate from packing material employed in the commercialization process. This research work devoted efforts in carrying quantitative analysis of the residues generated in the agricultural enterprise at its final destination. Data survey followed the directions implemented by the Residues Management Program issued by the agricultural enterprise. It was noticed from that analysis the necessity of changing the logistics applied to the recyclable material collecting process. However, composting process was elected as the organic compounds destination which is considered adequate for a material composed of significant percentage of organic matter far higher than wood, cardboard and plastics contents.
Abstract: Ionanofluids are a new and innovative class of heat transfer fluids which exhibit fascinating thermophysical properties compared to their base ionic liquids. This paper deals with the findings of thermal conductivity and specific heat capacity of ionanofluids as a function of a temperature and concentration of nanotubes. Simulation results using ionanofluids as coolants in heat exchanger are also used to access their feasibility and performance in heat transfer devices. Results on thermal conductivity and heat capacity of ionanofluids as well as the estimation of heat transfer areas for ionanofluids and ionic liquids in a model shell and tube heat exchanger reveal that ionanofluids possess superior thermal conductivity and heat capacity and require considerably less heat transfer areas as compared to those of their base ionic liquids. This novel class of fluids shows great potential for advanced heat transfer applications.
Abstract: More and more natural disasters are happening every
year: floods, earthquakes, volcanic eruptions, etc. In order to reduce
the risk of possible damages, governments all around the world are
investing into development of Early Warning Systems (EWS) for
environmental applications. The most important task of the EWS is
identification of the onset of critical situations affecting environment
and population, early enough to inform the authorities and general
public. This paper describes an approach for monitoring of flood
protections systems based on machine learning methods. An
Artificial Intelligence (AI) component has been developed for
detection of abnormal dike behaviour. The AI module has been
integrated into an EWS platform of the UrbanFlood project (EU
Seventh Framework Programme) and validated on real-time
measurements from the sensors installed in a dike.
Abstract: Accumulation of dust from the outdoor environment
on the panels of solar photovoltaic (PV) system is natural. There
were studies that showed that the accumulated dust can reduce the
performance of solar panels, but the results were not clearly
quantified. The objective of this research was to study the effects of
dust accumulation on the performance of solar PV panels.
Experiments were conducted using dust particles on solar panels with
a constant-power light source, to determine the resulting electrical
power generated and efficiency. It was found from the study that the
accumulated dust on the surface of photovoltaic solar panel can
reduce the system-s efficiency by up to 50%.
Abstract: A dual-reciprocity boundary element method is presented
for the numerical solution of a class of axisymmetric elastodynamic
problems. The domain integrals that arise in the integrodifferential
formulation are converted to line integrals by using the
dual-reciprocity method together suitably constructed interpolating
functions. The second order time derivatives of the displacement
in the governing partial differential equations are suppressed by
using Laplace transformation. In the Laplace transform domain, the
problem under consideration is eventually reduced to solving a system
of linear algebraic equations. Once the linear algebraic equations are
solved, the displacement and stress fields in the physical domain can
be recovered by using a numerical technique for inverting Laplace
transforms.
Abstract: In this paper, the construction of a detailed spine
model is presented using the LifeMOD Biomechanics Modeler. The
detailed spine model is obtained by refining spine segments in
cervical, thoracic and lumbar regions into individual vertebra
segments, using bushing elements representing the intervertebral
discs, and building various ligamentous soft tissues between
vertebrae. In the sagittal plane of the spine, constant force will be
applied from the posterior to anterior during simulation to determine
dynamic characteristics of the spine. The force magnitude is
gradually increased in subsequent simulations. Based on these
recorded dynamic properties, graphs of displacement-force
relationships will be established in terms of polynomial functions by
using the least-squares method and imported into a haptic integrated
graphic environment. A thoracolumbar spine model with complex
geometry of vertebrae, which is digitized from a resin spine
prototype, will be utilized in this environment. By using the haptic
technique, surgeons can touch as well as apply forces to the spine
model through haptic devices to observe the locomotion of the spine
which is computed from the displacement-force relationship graphs.
This current study provides a preliminary picture of our ongoing
work towards building and simulating bio-fidelity scoliotic spine
models in a haptic integrated graphic environment whose dynamic
properties are obtained from LifeMOD. These models can be helpful
for surgeons to examine kinematic behaviors of scoliotic spines and
to propose possible surgical plans before spine correction operations.
Abstract: 28 healthy adult Maradi bucks were used to evaluate
sperm production and sperm storage capacity in the breed. Daily
sperm production (DSP) averaged 0.55±0.05x109, while the daily
sperm production/g (DSP/g) was 1.37±0.12 x107. Gonadal sperm
reserve was 1.99±0.18 x109, while the caput, upper corpus and lower
corpus averaged 0.58±0.04 x109, 0.36±0.02 x109 and 0.33±0.08 x109
respectively. The proximal cauda, mid cauda, distal cauda and ductus
deferens had values of 0.68±0.10 x109, 1.23±0.16 x109,1.87±0.
x109and 0.17±0.05 x109 respectively. The relative contributions of
the respective epididymal sections and ductus deferens to the total
extragonadal sperm reserves were, 11.11%, 6.89%, 6.32%, 13.03%,
23.56%, 35.82% and 3.26% respectively. Gonadal sperm reserves
were significantly higher (p0.05) to
mid cauda and distal cauda epididymal reserves.
Abstract: The main objective of the paper has been represented
by the identification of the changes that occurred in the competitive
environment and their impact on the strategic marketing management
of companies in B2B market. At Romania-s level there has not yet
been done a similar research that studies change management in
crises on business to business field. In order to answer to the paper-s
objectives, a qualitative marketing research (in-depth structured
interview) was conducted, within the top management of 27
companies in Romanian business to business field. The main results
of the research highlight the necessity of a management of change, as
a result of the crises, as follows: changes in the corporate objectives
(from development objectives to maintaining objectives), changes
market segmentation and in competitive advantages, changes at the
level of market strategies and of the marketing mix.
Abstract: Reinforced Concrete (RC) structures strengthened
with fiber reinforced polymer (FRP) lack in thermal resistance under
elevated temperatures in the event of fire. This phenomenon led to
the lining of strengthened concrete with thin high performance
cementitious composites (THPCC) to protect the substrate against
elevated temperature. Elevated temperature effects on THPCC, based
on different cementitious materials have been studied in the past but
high-alumina cement (HAC)-based THPCC have not been well
characterized. This research study will focus on the THPCC based on
HAC replaced by 60%, 70%, 80% and 85% of ground granulated
blast furnace slag (GGBS). Samples were evaluated by the
measurement of their mechanical strength (28 & 56 days of curing)
after exposed to 400°C, 600°C and 28°C of room temperature for
comparison and corroborated by their microstructure study. Results
showed that among all mixtures, the mix containing only HAC
showed the highest compressive strength after exposed to 600°C as
compared to other mixtures. However, the tensile strength of THPCC
made of HAC and 60% GGBS content was comparable to the
THPCC with HAC only after exposed to 600°C. Field emission
scanning electron microscopy (FESEM) images of THPCC
accompanying Energy Dispersive X-ray (EDX) microanalysis
revealed that the microstructure deteriorated considerably after
exposure to elevated temperatures which led to the decrease in
mechanical strength.
Abstract: Alpfa-fetoprotein and its fragments may be an important vehicle for targeted delivery of radionuclides to the tumor. We investigated the effect of conditions on the labeling of biologically active synthetic peptide based on the (F-afp) with technetium-99m. The influence of the nature of the buffer solution, pH, concentration of reductant, concentration of the peptide and the reaction temperature on the yield of labeling was examined. As a result, the following optimal conditions for labeling of (F-afp) are found: pH 8.5 (phosphate and bicarbonate buffers) and pH from 1.7 to 7.0 (citrate buffer). The reaction proceeds with sufficient yield at room temperature for 30 min at the concentration of SnCl2 and (Fafp) (F-afp) is to be less than 10 mkg/ml and 25 mkg/ml, respectively. Investigations of the test drug accumulation in the tumor cells of human breast cancer were carried out. Results can be assumed that the in vivo study of the (F-afp) in experimental tumor lesions will show concentrations sufficient for imaging these lesions by SPECT.
Abstract: New lead-free ferroelectric relaxor ceramics were
prepared by conventional solid-state synthesis in the BaTiO3-Bi2O3-
Y2O3 systems. Some of these ceramics present a ferroelectric relaxor
with transition temperature close to room temperature. These new
materials are very interesting for applications and can replace leadbased
ceramic to prevent the toxic pollutions during the preparation
state. In the other hand, the energy band diagram shows the
potentiality of these compounds for the solar energy conversion.
Thus, some compositions have been tested successfully for H2
production upon visible light. The best activity occurs in alkaline
media with a rate evolution of about 0.15 mL g-1 mn-1 and a quantum
yield of 1% under polychromatic light.
Abstract: The goals of the present research are to estimate Six Sigma implementation in Latvian commercial banks and to identify the perceived benefits of its implementation. To achieve the goals, the authors used sequential explanatory method. To obtain empirical data, the authors have developed the questionnaire and adapted it for the employees of Latvian commercial banks. The questions are related to Six Sigma implementation and its perceived benefits. The questionnaire mainly consists of closed questions, the evaluation of which is based on 5 point Likert scale. The obtained empirical data has shown that of the two hypotheses put forward in the present research – Hypothesis 1 – has to be rejected, while Hypothesis 2 has been partially confirmed. The authors have also faced some research limitations related to the fact that the participants in the questionnaire belong to different rank of the organization hierarchy.
Abstract: A computational platform is presented in this
contribution. It has been designed as a virtual laboratory to be used
for exploring optimization algorithms in biological problems. This
platform is built on a blackboard-based agent architecture. As a test
case, the version of the platform presented here is devoted to the
study of protein folding, initially with a bead-like description of the
chain and with the widely used model of hydrophobic and polar
residues (HP model). Some details of the platform design are
presented along with its capabilities and also are revised some
explorations of the protein folding problems with different types of
discrete space. It is also shown the capability of the platform to
incorporate specific tools for the structural analysis of the runs in
order to understand and improve the optimization process.
Accordingly, the results obtained demonstrate that the ensemble of
computational tools into a single platform is worthwhile by itself,
since experiments developed on it can be designed to fulfill different
levels of information in a self-consistent fashion. By now, it is being
explored how an experiment design can be useful to create a
computational agent to be included within the platform. These
inclusions of designed agents –or software pieces– are useful for the
better accomplishment of the tasks to be developed by the platform.
Clearly, while the number of agents increases the new version of the
virtual laboratory thus enhances in robustness and functionality.
Abstract: A novel file splitting technique for the reduction of the nth-order entropy of text files is proposed. The technique is based on mapping the original text file into a non-ASCII binary file using a new codeword assignment method and then the resulting binary file is split into several subfiles each contains one or more bits from each codeword of the mapped binary file. The statistical properties of the subfiles are studied and it is found that they reflect the statistical properties of the original text file which is not the case when the ASCII code is used as a mapper. The nth-order entropy of these subfiles are determined and it is found that the sum of their entropies is less than that of the original text file for the same values of extensions. These interesting statistical properties of the resulting subfiles can be used to achieve better compression ratios when conventional compression techniques are applied to these subfiles individually and on a bit-wise basis rather than on character-wise basis.
Abstract: This work involved the use of phytoremediation to
remediate an aged soil contaminated with polychlorinated biphenyls
(PCBs). At microcosm scale, tests were prepared using soil samples
that have been collected in an industrial area with a total PCBs
concentration of about 250 μg kg-1. Medicago sativa and Lolium
italicum were the species selected in this study that is used as
“feasibility test" for full scale remediation. The experiment was
carried out with the addition of a mixture of randomly methylatedbeta-
cyclodextrins (RAMEB). At the end of the experiment analysis
of soil samples showed that in general the presence of plants has led
to a higher degradation of most congeners with respect to not
vegetated soil. The two plant species efficiencies were comparable
and improved by RAMEB addition with a final reduction of total
PCBs near to 50%. With increasing the chlorination of the congeners
the removal percentage of PCBs progressively decreased.
Abstract: Sequences of execution of algorithms in an interactive
manner using multimedia tools are employed in this paper. It helps to
realize the concept of fundamentals of algorithms such as searching
and sorting method in a simple manner. Visualization gains more
attention than theoretical study and it is an easy way of learning
process. We propose methods for finding runtime sequence of each
algorithm in an interactive way and aims to overcome the drawbacks
of the existing character systems. System illustrates each and every
step clearly using text and animation. Comparisons of its time
complexity have been carried out and results show that our approach
provides better perceptive of algorithms.