Abstract: The commercial finite element program LS-DYNA was employed to evaluate the response and energy absorbing capacity of cylindrical metal tubes that are externally wrapped with composite. The effects of composite wall thickness, loading conditions and fiber ply orientation were examined. The results demonstrate that a wrapped composite can be utilized effectively to enhance the crushing characteristics and energy absorbing capacity of the tubes. Increasing the thickness of the composite increases the mean force and the specific energy absorption under both static and dynamic crushing. The ply pattern affects the energy absorption capacity and the failure mode of the metal tube and the composite material property is also significant in determining energy absorption efficiency.
Abstract: Renewable and non-renewable resource constraints have been vast studied in theoretical fields of project scheduling problems. However, although cumulative resources are widespread in practical cases, the literature on project scheduling problems subject to these resources is scant. So in order to study this type of resources more, in this paper we use the framework of a resource constrained project scheduling problem (RCPSP) with finish-start precedence relations between activities and subject to the cumulative resources in addition to the renewable resources. We develop a branch and bound algorithm for this problem customizing precedence tree algorithm of RCPSP. We perform extensive experimental analysis on the algorithm to check its effectiveness and performance for solving different instances of the problem in question.
Abstract: A stiffened laminated composite panel (1 m length ×
0.5m width) was optimized for minimum weight and deflection under
several constraints using genetic algorithm. Here, a significant study
on the performance of a penalty function with two kinds of static and
dynamic penalty factors was conducted. The results have shown that
linear dynamic penalty factors are more effective than the static ones.
Also, a specially combined linear-exponential function has shown to
perform more effective than the previously mentioned penalty
functions. This was then resulted in the less sensitivity of the GA to
the amount of penalty factor.
Abstract: Controlled modification of appropriate sharpness for
nanotips is of paramount importance to develop novel materials and
functional devices at a nanometer resolution. Herein, we present a
reliable and unique strategy of laser irradiation enhanced
physicochemical etching to manufacture super sharp tungsten tips
with reproducible shape and dimension as well as high yields
(~80%). The corresponding morphology structure evolution of
tungsten tips and laser-tip interaction mechanisms were
systematically investigated and discussed using field emission
scanning electron microscope (SEM) and physical optics statistics
method with different fluences under 532 nm laser irradiation. This
work paves the way for exploring more accessible metallic tips
applications with tunable apex diameter and aspect ratio, and,
furthermore, facilitates the potential sharpening enhancement
technique for other materials used in a variety of nanoscale devices.
Abstract: This paper presents the cepstral and trispectral
analysis of a speech signal produced by normal men, men with
defective audition (deaf, deep deaf) and others affected by
tracheotomy, the trispectral analysis based on parametric methods
(Autoregressive AR) using the fourth order cumulant. These
analyses are used to detect and compare the pitches and the formants
of corresponding voiced sounds (vowel \a\, \i\ and \u\). The first
results appear promising, since- it seems after several experimentsthere
is no deformation of the spectrum as one could have supposed
it at the beginning, however these pathologies influenced the two
characteristics:
The defective audition influences to the formants contrary to the
tracheotomy, which influences the fundamental frequency (pitch).
Abstract: In this paper, a vision based system has been used for
controlling an industrial 3P Cartesian robot. The vision system will
recognize the target and control the robot by obtaining images from
environment and processing them. At the first stage, images from
environment are changed to a grayscale mode then it can diverse and
identify objects and noises by using a threshold objects which are
stored in different frames and then the main object will be
recognized. This will control the robot to achieve the target. A vision
system can be an appropriate tool for measuring errors of a robot in a
situation where the experimental test is conducted for a 3P robot.
Finally, the international standard ANSI/RIA R15.05-2 is used for
evaluating the path-related characteristics of the robot. To evaluate
the performance of the proposed method experimental test is carried
out.
Abstract: We present in this paper an acquisition and treatment system designed for semi-analog Gamma-camera. It consists of a nuclear medical Image Acquisition, Treatment and Display chain(IATD) ensuring the acquisition, the treatment of the signals(resulting from the Gamma-camera detection head) and the scintigraphic image construction in real time. This chain is composed by an analog treatment board and a digital treatment board. We describe the designed systems and the digital treatment algorithms in which we have improved the performance and the flexibility. The digital treatment algorithms are implemented in a specific reprogrammable circuit FPGA (Field Programmable Gate Array).interface for semi-analog cameras of Sopha Medical Vision(SMVi) by taking as example SOPHY DS7. The developed system consists of an Image Acquisition, Treatment and Display (IATD) ensuring the acquisition and the treatment of the signals resulting from the DH. The developed chain is formed by a treatment analog board and a digital treatment board designed around a DSP [2]. In this paper we have presented the architecture of a new version of our chain IATD in which the integration of the treatment algorithms is executed on an FPGA (Field Programmable Gate Array)
Abstract: A wideband 2-1-1 cascaded ΣΔ modulator with a
single-bit quantizer in the two first stages and a 4-bit quantizer in the
final stage is developed. To reduce sensitivity of digital-to-analog
converter (DAC) nonlinearities in the feedback of the last stage,
dynamic element matching (DEM) is introduced. This paper presents
two modelling approaches: The first is MATLAB description and the
second is VHDL-AMS modelling of the proposed architecture and
exposes some high-level-simulation results allowing a behavioural
study. The detail of both ideal and non-ideal behaviour modelling are
presented. Then, the study of the effect of building blocks
nonidealities is presented; especially the influences of nonlinearity,
finite operational amplifier gain, amplifier slew rate limitation and
capacitor mismatch. A VHDL-AMS description presents a good
solution to predict system-s performances and can provide sensitivity
curves giving the impact of nonidealities on the system performance.
Abstract: In order to enhance the knowledge of certain
phytochemical Algerian plants that are widely used in traditional
medicine and to exploit their therapeutic potential in modern
medicine, we have done a specific extraction of terpenes and
alkaloids from the leaves of Euphorbia granulata to evaluate the
antioxidant and antibacterial activity of this extracts. After the
extraction it was found that the terpene extract gave the highest yield
59.72% compared with alkaloids extracts.
The disc diffusion method was used to determine the antibacterial
activity against different bacterial strains: Escherichia coli
(ATCC25922), Pseudomonas aeruginosa (ATCC27853) and
Staphylococcus aureus (ATCC25923). All extracts have shown
inhibition of growth bacteria. The different zones of inhibition have
varied from (7 -10 mm) according to the concentrations of extract
used.
Testing the antiradical activity on DPPH-TLC plates indicated the
presence of substances that have potent anti-free radical. As against,
the BC-TLC revealed that only terpenes extract which was reacted
positively. These results can validate the importance of Euphorbia
granulata in traditional medicine.
Abstract: This paper suggests ranking alternatives under fuzzy
MCDM (multiple criteria decision making) via an centroid based
ranking approach, where criteria are classified to benefit qualitative,
benefit quantitative and cost quantitative ones. The ratings of
alternatives versus qualitative criteria and the importance weights of
all criteria are assessed in linguistic values represented by fuzzy
numbers. The membership function for the final fuzzy evaluation
value of each alternative can be developed through α-cuts and
interval arithmetic of fuzzy numbers. The distance between the
original point and the relative centroid is applied to defuzzify the
final fuzzy evaluation values in order to rank alternatives. Finally a
numerical example demonstrates the computation procedure of the
proposed model.
Abstract: In order to monitor the water table depth on soil profile
salinity buildup, a field study was carried out during 2006-07. Wheat
(Rabi) and Sorghum (Kharif) fodder were sown in with three
treatments. The results showed that watertable depth lowered from
1.15m to 2.89 m depth at the end of experiment. With lower of
watertable depth, pH, ECe and SAR decreased under crops both
without and with gypsum and increased in fallowing. Soil moisture
depletion was directly proportional to lowering of watertable. With the
application of irrigation water (58cm) pH, ECe and SAR were reduced
in cropped plots, reduction was higher in gypsum applied plots than
non-gypsum plots. In case of fallowing, there was increase in pH, EC,
while slight reduction occurred in SAR values. However, soil salinity
showed an increasing upward trend under fallowing and its value in
0-30 cm soil layer was the highest amongst the treatments.
Abstract: The free and forced in-plane vibrations of axially
moving plates are investigated in this work. The plate possesses an
internal damping of which the constitutive relation obeys the
Kelvin-Voigt model, and the excitations are arbitrarily distributed on
two opposite edges. First, the equations of motion and the boundary
conditions of the axially moving plate are derived. Then, the extended
Ritz method is used to obtain discretized system equations. Finally,
numerical results for the natural frequencies and the mode shapes of
the in-plane vibration and the in-plane response of the moving plate
subjected to arbitrary edge excitations are presented. It is observed that
the symmetry class of the mode shapes of the in-plane vibration
disperses gradually as the moving speed gets higher, and the u- and
v-components of the mode shapes belong to different symmetry class.
In addition, large response amplitudes having shapes similar to the
mode shapes of the plate can be excited by the edge excitations at the
resonant frequencies and with the same symmetry class of distribution
as the u-components.
Abstract: There has been gradual progress of late in construction projects, particularly in big-scale megaprojects. Due to the long-term construction period, however, with large-scale budget investment, lack of construction management technologies, and increase in the incomplete elements of project schedule management, a plan to conduct efficient operations and to ensure business safety is required. In particular, as the project management information system (PMIS) is meant for managing a single project centering on the construction phase, there is a limitation in the management of program-scale businesses like megaprojects. Thus, a program management information system (PgMIS) that includes program-level management technologies is needed to manage multiple projects. In this study, a support tool was developed for managing the cost and schedule information occurring in the construction phase, at the program level. In addition, a case study on the developed support tool was conducted to verify the usability of the system. With the use of the developed support tool program, construction managers can monitor the progress of the entire project and of the individual subprojects in real time.
Abstract: In this work, an organic compound 5,10,15,20-
Tetrakis(3,5-di-tertbutylphenyl)porphyrinatocopper(II) (TDTBPPCu)
is studied as an active material for thin film electronic devices. To
investigate the electrical properties of TDTBPPCu, junction of
TDTBPPCu with heavily doped n-Si and Al is fabricated.
TDTBPPCu film was sandwiched between Al and n-Si electrodes.
Various electrical parameters of TDTBPPCu are determined. The
current-voltage characteristics of the junction are nonlinear,
asymmetric and show rectification behavior, which gives the clue of
formation of depletion region. This behavior indicates the potential
of TDTBPPCu for electronics applications. The current-voltage and
capacitance-voltage techniques are used to find the different
electronic parameters.
Abstract: This paper presents the H-ARQ techniques comparison for OFDM systems with a new family of non-binary LDPC codes which has been developed within the EU FP7 DAVINCI project. The punctured NB-LDPC codes have been used in a simulated model of the transmission system. The link level performance has been evaluated in terms of spectral efficiency, codeword error rate and average number of retransmissions. The NB-LDPC codes can be easily and effective implemented with different methods of the retransmission needed if correct decoding of a codeword failed. Here the Optimal Symbol Selection method is proposed as a Chase Combining technique.
Abstract: Two algorithms are proposed to reduce the storage requirements for mammogram images. The input image goes through a shrinking process that converts the 16-bit images to 8-bits by using pixel-depth conversion algorithm followed by enhancement process. The performance of the algorithms is evaluated objectively and subjectively. A 50% reduction in size is obtained with no loss of significant data at the breast region.
Abstract: In this study, we report the synthesis and
characterization of nanohydroxyapatite (nHAp) in gelatin-starch
matrix via biomimetic method. Characterization of the samples was
performed using X-ray diffraction (XRD) and Fourier Transform
infrared spectroscopy (FT-IR). The Size and morphology of the
nHAp samples were determined using scanning and transmission
electron microscopy (SEM and TEM). The results reveal that the
shape and morphology of nHAp is influenced by presence of
biopolymers as template. Carbonyl and amino groups from gelatin
and hydroxyl from starch play crucial roles in HAp formation on the
surface of gelatin-starch.
Abstract: The effect of different tempering temperatures and heat treatment times on the corrosion resistance of austenitic stainless steels in oxalic acid was studied in this work using conventional weight loss and electrochemical measurements. Typical 304 and 316 stainless steel samples were tempered at 150oC, 250oC and 350oC after being austenized at 1050oC for 10 minutes. These samples were then immersed in 1.0M oxalic acid and their weight losses were measured at every five days for 30 days. The results show that corrosion of both types of ASS samples increased with an increase in tempering temperature and time and this was due to the precipitation of chromium carbides at the grain boundaries of these metals. Electrochemical results also confirm that the 304 ASS is more susceptible to corrosion than 316 ASS in this medium. This is attributed to the molybdenum in the composition of the latter. The metallographic images of these samples showed non–uniform distribution of precipitated chromium carbides at the grain boundaries of these metals and unevenly distributed carbides and retained austenite phases which cause galvanic effects in the medium.
Abstract: This paper presents the identification of the impact
force acting on a simply supported beam. The force identification is
an inverse problem in which the measured response of the structure is
used to determine the applied force. The identification problem is
formulated as an optimization problem and the genetic algorithm is
utilized to solve the optimization problem. The objective function is
calculated on the difference between analytical and measured
responses and the decision variables are the location and magnitude
of the applied force. The results from simulation show the
effectiveness of the approach and its robustness vs. the measurement
noise and sensor location.
Abstract: Visible Light Communication (VLC) offers advantages of low energy consumption, licence free and RF interference free operation. One application area for VLC is in the provision of health centred services circumventing issues of interference with any biomedical device within the environment. VLC performamce is affected by natural light restricting systems avilability and relibility. The paper presents an analysis of the performance of VLC systems under different meteorological conditions. The evaluation considered the impact of natural light as a function of different reflection surfaces in different room sizes.