Abstract: The control of commutation of switched reluctance
(SR) motor has nominally depended on a physical position detector.
The physical rotor position sensor limits robustness and increases
size and inertia of the SR drive system. The paper describes a method
to overcome these limitations by using magnetization characteristics
of the motor to indicate rotor and stator teeth overlap status. The
method is using active current probing pulses of same magnitude that
is used to simulate flux linkage in the winding being probed. A
microprocessor is used for processing magnetization data to deduce
rotor-stator teeth overlap status and hence rotor position. However,
the back-of-core saturation and mutual coupling introduces overlap
detection errors, hence that of commutation control. This paper
presents the concept of the detection scheme and the effects of backof
core saturation.
Abstract: We report the results of an lattice Boltzmann
simulation of magnetohydrodynamic damping of sidewall convection
in a rectangular enclosure filled with a porous medium. In particular
we investigate the suppression of convection when a steady magnetic
field is applied in the vertical direction. The left and right vertical
walls of the cavity are kept at constant but different temperatures
while both the top and bottom horizontal walls are insulated. The
effects of the controlling parameters involved in the heat transfer and
hydrodynamic characteristics are studied in detail. The heat and mass
transfer mechanisms and the flow characteristics inside the enclosure
depended strongly on the strength of the magnetic field and Darcy
number. The average Nusselt number decreases with rising values of
the Hartmann number while this increases with increasing values of
the Darcy number.
Abstract: In this paper, a double balanced radio frequency multiplier
is presented which is customized for transmitted reference
ultra wideband (UWB) receivers. The multiplier uses 90nm model
parameters and exploits compensating transistors to provide controllable
gain for a Gilbert core. After performing periodic and quasiperiodic
non linear analyses the RF mixer (multiplier) achieves a
voltage conversion gain of 16 dB and a DSB noise figure of 8.253
dB with very low power consumption. A high degree of LO to RF
isolation (in the range of -94dB), RF to IF isolation (in the range of
-95dB) and LO to IF isolation (in the range of -143dB) is expected
for this design with an input-referred IP3 point of -1.93 dBm and an
input referred 1 dB compression point of -10.67dBm. The amount of
noise at the output is 7.7 nV/√Hz when the LO input is driven by
a 10dBm signal. The mixer manifests better results when compared
with other reported multiplier circuits and its Zero-IF performance
ensures its applicability as TR-UWB multipliers.
Abstract: This paper investigates experimental and numerical study of the airflow characteristics for vortex, round and square ceiling diffusers and its effect on the thermal comfort in a ventilated room. Three different thermal comfort criteria namely; Mean Age of the Air (MAA), ventilation effectiveness (E), and Effective Draft Temperature (EDT) have been used to predict the thermal comfort zone inside the room. In experimental work, a sub-scale room is set-up to measure the temperature field in the room. In numerical analysis, unstructured grids have been used to discretize the numerical domain. Conservation equations are solved using FLUENT commercial flow solver. The code is validated by comparing the numerical results obtained from three different turbulence models with the available experimental data. The comparison between the various numerical models shows that the standard k-ε turbulence model can be used to simulate these cases successfully. After validation of the code, effect of supply air velocity on the flow and thermal field could be investigated and hence the thermal comfort. The results show that the pressure coefficient created by the square diffuser is 1.5 times greater than that created by the vortex diffuser. The velocity decay coefficient is nearly the same for square and round diffusers and is 2.6 times greater than that for the vortex diffuser.
Abstract: The Linear discriminant analysis (LDA) can be
generalized into a nonlinear form - kernel LDA (KLDA) expediently
by using the kernel functions. But KLDA is often referred to a general
eigenvalue problem in singular case. To avoid this complication, this
paper proposes an iterative algorithm for the two-class KLDA. The
proposed KLDA is used as a nonlinear discriminant classifier, and the
experiments show that it has a comparable performance with SVM.
Abstract: The present study conducted experimental investigation on combustion and emission characteristics of compression ignition engine using diesel as pilot fuel and methane, hydrogen and methane/hydrogen mixture as gaseous fuels at 1800 rev min-1. The effect of gaseous fuel on peak cylinder pressure and heat release is modest at low to medium loads. At high load, the high combustion temperature and high quantity of pilot fuel contribute to better combustion efficiency for all kinds of gaseous fuels and increases the peak cylinder pressure. Enrichment of hydrogen in methane gradually increases the peak cylinder pressure. The brake thermal efficiency increases with higher hydrogen fraction at lower loads. Hydrogen addition in methane contributed to a proportional reduction of CO/CO2/HC emission without penalty of NOx. For particulate emission, methane and hydrogen, could both suppress the particle emission. 30% hydrogen fraction in methane is observed to be best in reducing the particulate emission.
Abstract: Arthrobacter viscosus biomass was used for Cr(VI)
biosorption. The effect of pH on Cr(VI) reduction and removal from
aqueous solution was studied in the range of 1-4. The Cr(VI) removal
involves both redox reaction and adsorption of metal ions on biomass
surface. The removal rate of Cr(VI) was enhanced by very acid
conditions, while higher solution pH values favored the removal of
total chromium. The best removal efficiency and uptake were
reached at pH 4, 72.5 % and 12.6 mgCr/gbiomass, respectively.
Abstract: In this paper the application of neuro-fuzzy system for equalization of channel distortion is considered. The structure and operation algorithm of neuro-fuzzy equalizer are described. The use of neuro-fuzzy equalizer in digital signal transmission allows to decrease training time of parameters and decrease the complexity of the network. The simulation of neuro-fuzzy equalizer is performed. The obtained result satisfies the efficiency of application of neurofuzzy technology in channel equalization.
Abstract: Carbon nanotubes (CNTs) are attractive because of
their excellent chemical durability mechanical strength and electrical
properties. Therefore there is interest in CNTs for not only electrical
and mechanical application, but also biological and medical
application.
In this study, the dispersion power of surfactant-treated multiwalled
carbon nanotubes (MWCNTs) and their effect on the antibacterial
activity were examined. Surfactant was used sodium
dodecyl-benzenesulfonate (SDBS). UV-vis absorbance and
transmission electron microscopy(TEM) were used to characterize the
dispersion of MWCNTs in the aqueous phase, showing that the
surfactant molecules had been adsorbed onto the MWCNTs surface.
The surfactant-treated MWCNTs exhibited antimicrobial activities
to streptococcus mutans. The optical density growth curves and viable
cell number determined by the plating method suggested that the
antimicrobial activity of surfactant-treated MWCNTs was both
concentration and treatment time-dependent.
Abstract: Sorghum flour was supplemented with 15 and 30%
chickpea flour. Sorghum flour and the supplement were fermented at
35 oC for 0, 8, 16, and 24 h. Changes in pH, titrable acidity, total
soluble solids, protein content, in vitro protein digestibility and
amino acid composition were investigated during fermentation and/or
after supplementation of sorghum flour with chickpea. The pH of the
fermenting material decreased sharply with a concomitant increase in
the titrable acidity. The total soluble solids remained unchanged with
progressive fermentation time. The protein content of sorghum
cultivar was found to be 9.27 and that of chickpea was 22.47%. The
protein content of sorghum cultivar after supplementation with15 and
30% chickpea was significantly (P ≤ 0.05) increased to 11.78 and
14.55%, respectively. The protein digestibility also increased after
fermentation from 13.35 to 30.59 and 40.56% for the supplements,
respectively. Further increment in protein content and digestibility
was observed when supplemented and unsupplemented samples were
fermented for different periods of time. Cooking of fermented
samples was found to increase the protein content slightly and
decreased digestibility for both supplements. Amino acid content of
fermented and fermented and cooked supplements was determined.
Supplementation was found to increase the lysine and therionine
content. Cooking following fermentation decreased lysine,
isoleucine, valine and sulfur containg amino acids.
Abstract: In this paper, we consider a designed and
implemented phase-cutting dimmer. In fact, the dimmer is closed
loop and a microcontroller calculates and then regulates the firing
delay angles of each channel. Depending on the firing angle, the
harmonic distortion in the input current will not comply with
international standards, such as IEC 61000-3-2 (class C equipments).
For solving this problem, eight harmonic compensators have been
added to the dimmer. So, the proposed dimmer has a little harmonic
distortion in the input current whereas conventional phase-cutting
dimmers are not so. Sensitivity and removed THD of the proposed
dimmer will be presented.
Abstract: It is known that the heart interacts with and adapts to its venous and arterial loading conditions. Various experimental studies and modeling approaches have been developed to investigate the underlying mechanisms. This paper presents a model of the left ventricle derived based on nonlinear stress-length myocardial characteristics integrated over truncated ellipsoidal geometry, and second-order dynamic mechanism for the excitation-contraction coupling system. The results of the model presented here describe the effects of the viscoelastic damping element of the electromechanical coupling system on the hemodynamic response. Different heart rates are considered to study the pacing effects on the performance of the left-ventricle against constant preload and afterload conditions under various damping conditions. The results indicate that the pacing process of the left ventricle has to take into account, among other things, the viscoelastic damping conditions of the myofilament excitation-contraction process. The effects of left ventricular dimensions on the hemdynamic response have been examined. These effects are found to be different at different viscoelastic and pacing conditions.
Abstract: This study presents the numerical simulation of
optimum pin-fin heat sink with air impinging cooling by using
Taguchi method. 9 L ( 4 3 ) orthogonal array is selected as a plan for
the four design-parameters with three levels. The governing
equations are discretized by using the
control-volume-based-finite-difference method with a power-law
scheme on the non-uniform staggered grid. We solved the coupling of
the velocity and the pressure terms of momentum equations using
SIMPLEC algorithm. We employ the k −ε two-equations
turbulence model to describe the turbulent behavior. The parameters
studied include fin height H (35mm-45mm), inter-fin spacing a , b ,
and c (2 mm-6.4 mm), and Reynolds number ( Re = 10000- 25000).
The objective of this study is to examine the effects of the fin
spacings and fin height on the thermal resistance and to find the
optimum group by using the Taguchi method. We found that the fin
spacings from the center to the edge of the heat sink gradually
extended, and the longer the fin’s height the better the results. The
optimum group is 3 1 2 3 H a b c . In addition, the effects of parameters are
ranked by importance as a , H , c , and b .
Abstract: The nonlinear damping behavior is usually ignored in
the design of a miniature moving-coil loudspeaker. But when the
loudspeaker operated in air, the damping parameter varies with the
voice-coil displacement corresponding due to viscous air flow. The
present paper presents an identification model as inverse problem to
identify the nonlinear damping parameter in the lumped parameter
model for the loudspeaker. Theoretical results for the nonlinear
damping are verified by using laser displacement measurement
scanner. These results indicate that the damping parameter has the
greatly different nonlinearity between in air and vacuum. It is believed
that the results of the present work can be applied in diagnosis and
sound quality improvement of a miniature loudspeaker.
Abstract: Discharges in hydrogen, ignited by wire explosion, with current amplitude up to 1.5 MA were investigated. Channel diameter oscillations were observed on the photostreaks. Voltage and current curves correlated with the photostreaks. At initial gas pressure of 5-35 MPa the oscillation period was proportional to square root of atomic number of the initiating wire material. These oscillations were associated with aligned magnetic and gas-kinetic pressures. At initial pressure of 80-160 MPa acoustic pressure fluctuations on the discharge chamber wall were increased up to 150 MPa and there were the growth of voltage fluctuations on the discharge gap up to 3 kV simultaneously with it. In some experiments it was observed abrupt increase in the oscillation amplitude, which can be caused by the resonance of the acoustic oscillations in discharge chamber volume and the oscillations connected with alignment of the gaskinetic pressure and the magnetic pressure, as far as frequencies of these oscillations are close to each other in accordance with the estimates and the experimental data. Resonance of different type oscillations can produce energy density increasing in the discharge channel. Thus, the appropriate initial conditions in the experiment allow to increase the energy density in the discharge channel
Abstract: Collective action can be an effective means for local development as well as important strategy to enhance livelihoods especially among rural people. This article explores the level of collective action among members of Fishermen-s Wives Group (KUNITA) in Malaysia. KUNITA was established by the Malaysian Fishery Development Authority (LKIM) with an objective to increase the socio-economic status of fishermen-s families. The members who are mostly the wives and daughters of fishermen are strongly encouraged by LKIM to venture into entrepreneurship activities. The objective of this research was to see the level of collective action among members in KUNITA groups in the state of Selangor. The finding shows that high level of collective action among KUNITA members is strongly based on volunteerism. However, the level of cooperation among members in the group is relatively low. The findings present significant challenges for the group in maintaining the sustainability of KUNITA organization.
Abstract: In this article, we expose our research work in
Human-machine Interaction. The research consists in manipulating
the workspace by eyes. We present some of our results, in particular
the detection of eyes and the mouse actions recognition. Indeed, the
handicaped user becomes able to interact with the machine in a more
intuitive way in diverse applications and contexts. To test our
application we have chooses to work in real time on videos captured
by a camera placed in front of the user.
Abstract: This study was set to determine the antimicrobial
activities of brine salting, chlorinated solution, and oil frying
treatments on enteric bacteria and fungi in Rastrineobola argentea
fish from fish landing beaches within L. Victoria basin of western
Kenya. Statistical differences in effectiveness of the different
treatment methods was determined by single factor ANOVA, and
paired two-tail t-Test was performed to compare the differences in
moisture contents before and after storage. Oil fried fish recorded the
lowest microbial loads, sodium chloride at 10% concentration was
the second most effective and chlorinated solution even at 150ppm
was the least effective against the bacteria and fungi in fish. Moisture
contents of the control and treated fish were significantly lower after
storage. These results show that oil frying of fish should be adopted
for processing and preserving Rastrineobola argentea which is the
most abundant and affordable fish species from Lake Victoria.
Abstract: The limit load carrying capacity of functionally
graded materials (FGM) circular plates subjected to an arbitrary
rotationally symmetric loading has been computed. It is provided that
the plate material behaves rigid perfectly plastic and obeys either the
Square or the Tresca yield criterion. To this end the upper and lower
bound principles of limit analysis are employed to determine the
exact value for the limiting load. The correctness of the result are
verified and finally limiting loads for two examples namely; through
radius and through thickness FGM circular plates with simply
supported edges are calculated, respectively and moreover, the values
of critical loading factor are determined.
Abstract: The research on two-wheeled inverted pendulum (TWIP) mobile robots or commonly known as balancing robots have gained momentum over the last decade in a number of robotic laboratories around the world. This paper describes the hardware design of such a robot. The objective of the design is to develop a TWIP mobile robot as well as MATLAB interfacing configuration to be used as flexible platform comprises of embedded unstable linear plant intended for research and teaching purposes. Issues such as selection of actuators and sensors, signal processing units, MATLAB Real Time Workshop coding, modeling and control scheme will be addressed and discussed. The system is then tested using a wellknown state feedback controller to verify its functionality.