Abstract: Space Vector Modulation (SVM) is an optimum Pulse Width Modulation (PWM) technique for an inverter used in a variable frequency drive applications. It is computationally rigorous and hence limits the inverter switching frequency. Increase in switching frequency can be achieved using Neural Network (NN) based SVM, implemented on application specific chips. This paper proposes a neural network based SVM technique for a Voltage Source Inverter (VSI). The network proposed is independent of switching frequency. Different architectures are investigated keeping the total number of neurons constant. The performance of the inverter is compared for various switching frequencies for different architectures of NN based SVM. From the results obtained, the network with minimum resource and appropriate word length is identified. The bit precision required for this application is identified. The network with 8-bit precision is implemented in the IC XCV 400 and the results are presented. The performance of NN based general purpose SVM with higher bit precision is discussed.
Abstract: Removal of Methylene Blue (MB) from aqueous
solution by adsorbing it on Gypsum was investigated by batch
method. The studies were conducted at 25°C and included the effects
of pH and initial concentration of Methylene Blue. The adsorption
data was analyzed by using the Langmuir, Freundlich and Tempkin
isotherm models. The maximum monolayer adsorption capacity was
found to be 36 mg of the dye per gram of gypsum. The data were
also analyzed in terms of their kinetic behavior and was found to
obey the pseudo second order equation.
Abstract: In the numerical solution of the forward dynamics of a
multibody system, the positions and velocities of the bodies in the
system are obtained first. With the information of the system state
variables at each time step, the internal and external forces acting on
the system are obtained by appropriate contact force models if the
continuous contact method is used instead of a discrete contact
method. The local deformation of the bodies in contact, represented
by penetration, is used to compute the contact force. The ability and
suitability with current cylindrical contact force models to describe
the contact between bodies with cylindrical geometries with
particular focus on internal contacting geometries involving low
clearances and high loads simultaneously is discussed in this paper.
A comparative assessment of the performance of each model under
analysis for different contact conditions, in particular for very
different penetration and clearance values, is presented. It is
demonstrated that some models represent a rough approximation to
describe the conformal contact between cylindrical geometries
because contact forces are underestimated.
Abstract: In this paper, we have applied the homotopy perturbation
method (HPM) for obtaining the analytical solution of unsteady
flow of gas through a porous medium and we have also compared the
findings of this research with some other analytical results. Results
showed a very good agreement between results of HPM and the
numerical solutions of the problem rather than other analytical solutions
which have previously been applied. The results of homotopy
perturbation method are of high accuracy and the method is very
effective and succinct.
Abstract: This paper estimates the economic values of
household preference for enhanced solid waste disposal services in
Malaysia. The contingent valuation (CV) method estimates an
average additional monthly willingness-to-pay (WTP) in solid waste
management charges of Ôé¼0.77 to 0.80 for improved waste disposal
services quality. The finding of a slightly higher WTP from the
generic CV question than that of label-specific, further reveals a
higher WTP for sanitary landfill, at Ôé¼0.90, than incineration, at Ôé¼0.63.
This suggests that sanitary landfill is a more preferred alternative.
The logistic regression estimation procedure reveals that household-s
concern of where their rubbish is disposed, age, ownership of house,
household income and format of CV question are significant factors
in influencing WTP.
Abstract: In this project, a tele-operated anthropomorphic
robotic arm and hand is designed and built as a versatile robotic arm
system. The robot has the ability to manipulate objects such as pick
and place operations. It is also able to function by itself, in
standalone mode.
Firstly, the robotic arm is built in order to interface with a personal
computer via a serial servo controller circuit board. The circuit board
enables user to completely control the robotic arm and moreover,
enables feedbacks from user. The control circuit board uses a
powerful integrated microcontroller, a PIC (Programmable Interface
Controller). The PIC is firstly programmed using BASIC (Beginner-s
All-purpose Symbolic Instruction Code) and it is used as the 'brain'
of the robot. In addition a user friendly Graphical User Interface
(GUI) is developed as the serial servo interface software using
Microsoft-s Visual Basic 6.
The second part of the project is to use speech recognition control
on the robotic arm. A speech recognition circuit board is constructed
with onboard components such as PIC and other integrated circuits. It
replaces the computers- Graphical User Interface. The robotic arm is
able to receive instructions as spoken commands through a
microphone and perform operations with respect to the commands
such as picking and placing operations.
Abstract: Dust storms are one of the most costly and destructive
events in many desert regions. They can cause massive damages both
in natural environments and human lives. This paper is aimed at
presenting a preliminary study on dust storms, as a major natural
hazard in arid and semi-arid regions. As a case study, dust storm
events occurred in Zabol city located in Sistan Region of Iran was
analyzed to diagnose and predict dust storms. The identification and
prediction of dust storm events could have significant impacts on
damages reduction. Present models for this purpose are complicated
and not appropriate for many areas with poor-data environments. The
present study explores Gamma test for identifying inputs of ANNs
model, for dust storm prediction. Results indicate that more attempts
must be carried out concerning dust storms identification and
segregate between various dust storm types.
Abstract: Osteoarthritis (OA) is the most prevalent and far common debilitating form of arthritis which can be defined as a degenerative condition affecting synovial joint. Patients suffering from osteoarthritis often complain of dull ache pain on movement.
Physical agents can fight the painful process when correctly indicated and used such as heat or cold therapy Aim. This study was carried out to: Compare the effect of cold, warm and contrast therapy on controlling knee osteoarthritis associated problems. Setting: The study was carried out in orthopedic outpatient clinics of Menoufia University and teaching Hospitals, Egypt. Sample: A convenient sample of 60 adult patients with unilateral knee osteoarthritis. Tools: three tools were utilized to collect the data. Tool I : An interviewing questionnaire. It comprised of three parts covering sociodemographic data, medical data and adverse effects of the treatment protocol. Tool II : Knee Injury and Osteoarthritis Outcome Score (KOOS) It consists of five main parts. Tool II1 : 0-10 Numeric pain rating scale. Results: reveled that the total knee symptoms score was decreased from moderate symptoms pre intervention to mild symptoms after warm and contrast method of therapy, but the contrast therapy had significant effect in reducing the knee symptoms and pain than the other symptoms. Conclusions: all of the three
methods of therapy resulted in improvement in all knee symptoms and pain but the most appropriate protocol of treatment to relive symptoms and pain was contrast therapy.
Abstract: The Chiu-s method which generates a Takagi-Sugeno Fuzzy Inference System (FIS) is a method of fuzzy rules extraction. The rules output is a linear function of inputs. In addition, these rules are not explicit for the expert. In this paper, we develop a method which generates Mamdani FIS, where the rules output is fuzzy. The method proceeds in two steps: first, it uses the subtractive clustering principle to estimate both the number of clusters and the initial locations of a cluster centers. Each obtained cluster corresponds to a Mamdani fuzzy rule. Then, it optimizes the fuzzy model parameters by applying a genetic algorithm. This method is illustrated on a traffic network management application. We suggest also a Mamdani fuzzy rules generation method, where the expert wants to classify the output variables in some fuzzy predefined classes.
Abstract: In this paper a novel algorithm is proposed that integrates the process of fuzzy hierarchy generation and rule discovery for automated discovery of Production Rules with Fuzzy Hierarchy (PRFH) in large databases.A concept of frequency matrix (Freq) introduced to summarize large database that helps in minimizing the number of database accesses, identification and removal of irrelevant attribute values and weak classes during the fuzzy hierarchy generation.Experimental results have established the effectiveness of the proposed algorithm.
Abstract: Perspective of food security in 21 century showed
shortage of food that production is faced to vital problem. Food
security strategy is applied longtime method to assess required food.
Meanwhile, nanotechnology revolution changes the world face.
Nanotechnology is adequate method utilize of its characteristics to
decrease environmental problems and possible further access to food
for small farmers. This article will show impact of production and
adoption of nanocrops on food security. Population is researchers of
agricultural research center of Esfahan province. The results of study
show that there was a relationship between uses, conversion,
distribution, and production of nanocrops, operative human
resources, operative circumstance, and constrains of usage of
nanocrops and food security. Multivariate regression analysis by
enter model shows that operative circumstance, use, production and
constrains of usage of nanocrops had positive impact on food security
and they determine in four steps 20 percent of it.
Abstract: The technical realization of data transmission using
glass fiber began after the development of diode laser in year 1962.
The erbium doped fiber amplifiers (EDFA's) in high speed networks
allow information to be transmitted over longer distances without
using of signal amplification repeaters. These kinds of fibers are
doped with erbium atoms which have energy levels in its atomic
structure for amplifying light at 1550nm. When a carried signal wave
at 1550nm enters the erbium fiber, the light stimulates the excited
erbium atoms which pumped with laser beam at 980nm as additional
light. The wavelength and intensity of the semiconductor lasers
depend on the temperature of active zone and the injection current.
The present paper shows the effect of the diode lasers temperature
and injection current on the optical amplification. From the results of
in- and output power one may calculate the max. optical gain by
erbium doped fiber amplifier.
Abstract: Although in sustainable development field, innovative
solutions have been sought worldwide by environmental groups,
academia, governments and companies for many years, recently,
citizens and communities have emerged as a new group and taken
more and more active role in this field. Many scholars call for more
research on the role of community and community innovation in
sustainable development. This paper is to respond to the calls. In
this paper, we first summarize a comprehensive set of innovation
principles. Then, we do a qualitative cross case study by comparing
three community innovation cases in three different areas of sustainable
development according to the innovation principles. Finally,
we summarize the case comparison and discuss the implications
to sustainable development. A unified role model and innovation
distribution map of community innovation are developed to better
understand community innovation in sustainable development..
Abstract: This paper presents a new method of fault detection and isolation (FDI) for polymer electrolyte membrane (PEM) fuel cell (FC) dynamic systems under an open-loop scheme. This method uses a radial basis function (RBF) neural network to perform fault identification, classification and isolation. The novelty is that the RBF model of independent mode is used to predict the future outputs of the FC stack. One actuator fault, one component fault and three sensor faults have been introduced to the PEMFC systems experience faults between -7% to +10% of fault size in real-time operation. To validate the results, a benchmark model developed by Michigan University is used in the simulation to investigate the effect of these five faults. The developed independent RBF model is tested on MATLAB R2009a/Simulink environment. The simulation results confirm the effectiveness of the proposed method for FDI under an open-loop condition. By using this method, the RBF networks able to detect and isolate all five faults accordingly and accurately.
Abstract: In this paper we present high performance
dynamically allocated multi-queue (DAMQ) buffer schemes for fault
tolerance systems on chip applications that require an interconnection
network. Two virtual channels shared the same buffer space. Fault
tolerant mechanisms for interconnection networks are becoming a
critical design issue for large massively parallel computers. It is also
important to high performance SoCs as the system complexity keeps
increasing rapidly. On the message switching layer, we make
improvement to boost system performance when there are faults
involved in the components communication. The proposed scheme is
when a node or a physical channel is deemed as faulty, the previous
hop node will terminate the buffer occupancy of messages destined
to the failed link. The buffer usage decisions are made at switching
layer without interactions with higher abstract layer, thus buffer
space will be released to messages destined to other healthy nodes
quickly. Therefore, the buffer space will be efficiently used in case
fault occurs at some nodes.
Abstract: This paper describes the challenges on the requirements engineering for developing an enterprise applications in higher
education environment. The development activities include software implementation, maintenance, and enhancement and support for online
transaction processing and overnight batch processing.
Generally, an enterprise application for higher education environment
may include Student Information System (SIS), HR/Payroll system,
Financial Systems etc. By the way, there are so many challenges in
requirement engineering phases in order to provide two distinctive
services that are production processing support and systems
development.
Abstract: Bandwidth allocation in wired network is less complex
and to allocate bandwidth in wireless networks is complex and
challenging, due to the mobility of source end system.This paper
proposes a new approach to bandwidth allocation to higher and lower
priority mobile nodes.In our proposal bandwidth allocation to new
mobile node is based on bandwidth utilization of existing mobile
nodes.The first section of the paper focuses on introduction to
bandwidth allocation in wireless networks and presents the existing
solutions available for allocation of bandwidth. The second section
proposes the new solution for the bandwidth allocation to higher and
lower priority nodes. Finally this paper ends with the analytical
evaluation of the proposed solution.
Abstract: Lutein is a dietary oxycarotenoid which is found
to reduce the risks of Age-related Macular Degeneration
(AMD). Supercritical fluid extraction of lutein esters from
marigold petals was carried out and was found to be much
effective than conventional solvent extraction. The
saponification of pre-concentrated lutein esters to produce free
lutein was studied which showed a composition of about 88%
total carotenoids (UV-VIS spectrophotometry) and 90.7%
lutein (HPLC). The lipase catalyzed hydrolysis of lutein esters
in conventional medium was investigated. The optimal
temperature, pH, enzyme concentration and water activity
were found to be 50°C, 7, 15% and 0.33 respectively and the
activity loss of lipase was about 25% after 8 times re-use in at
50°C for 12 days. However, the lipase catalyzed hydrolysis of
lutein esters in conventional media resulted in poor
conversions (16.4%).
Abstract: The most severe damage of the turbine rotor is its
distortion. The rotor straightening process must lead, at the first
stage, to removal of the stresses from the material by annealing and
next, to straightening of the plastic distortion without leaving any
stress by hot spotting. The straightening method does not produce
stress accumulations and the heating technique, developed
specifically for solid forged rotors and disks, enables to avoid local
overheating and structural changes in the material. This process also
does not leave stresses in the shaft material. An experimental study
of hot spotting is carried out on a large turbine rotor and some of the
most important effective parameters that must be considered on
annealing and hot spotting processes are investigated in this paper.
Abstract: In high powered dense wavelength division
multiplexed (WDM) systems with low chromatic dispersion,
four-wave mixing (FWM) can prove to be a major source of noise.
The MultiCanonical Monte Carlo Method (MCMC) and the Split
Step Fourier Method (SSFM) are combined to accurately evaluate the
probability density function of the decision variable of a receiver,
limited by FWM. The combination of the two methods leads to more
accurate results, and offers the possibility of adding other optical
noises such as the Amplified Spontaneous Emission (ASE) noise.