Abstract: This paper presents the development of an active
vibration control using direct adaptive controller to suppress the
vibration of a flexible beam system. The controller is realized based
on linear parametric form. Differential evolution optimisation
algorithm is used to optimize the controller using single objective
function by minimizing the mean square error of the observed
vibration signal. Furthermore, an alternative approach is developed to
systematically search for the best controller model structure together
with it parameter values. The performance of the control scheme is
presented and analysed in both time and frequency domain.
Simulation results demonstrate that the proposed scheme is able to
suppress the unwanted vibration effectively.
Abstract: Thyroid dysfunction is one of the most frequently
reported complications of chronic blood transfusion therapy in patients with beta-thalassemia major (BTM). However, the occurrence of thyroid dysfunction and its possible association with
iron overload in BTM patients is still under debate. Therefore, this
study aimed to investigate the status of thyroid functions and iron overload in adolescent and young adult patients with BTM in Jordan population. Thirty six BTM patients aged 12-28 years and matched controls were included in this study. All patients have been receiving frequent blood transfusion to maintain pretransfusion hemoglobin
concentration above 10 g dl-1 and deferoxamine at a dose of 45 mg kg-1 day-1 (8 h, 5-7 days/week) by subcutaneous infusion. Blood
samples were drawn from patients and controls. The status of thyroid functions and iron overload was evaluated by measurements of serum
free thyroxine (FT4), triiodothyronine (FT3), thyrotropin (TSH) and
serum ferritin level. A number of some hematological and
biochemical parameters were also measured. It was found that hematocrit, serum ferritin, hemoglobin, FT3 and zinc, copper mean values were significantly higher in the patients than in the controls (P< 0.05). On other hand, leukocyte, FT4 and TSH mean values were
similar to that of the controls. In addition, our data also indicated that
all of the above examined parameters were not significantly affected
by the patient-s age and gender. Deferoxamine approach for removing excess iron from our BTM patient did not normalize the
values of serum ferritin, copper and zinc, suggesting poor compliance
with deferoxamine chelation therapy. Thus, we recommend the use
of a combination of deferoxamine and deferiprone to reduce the risk
of excess of iron in our patients. Furthermore, thyroid dysfunction
appears to be a rare complication, because our patients showed
normal mean levels for serum TSH and FT4. However, high mean
levels of serum ferritin, zinc, copper might be seen as potential risk
factors for initiation and development of thyroid dysfunctions and
other diseases. Therefore, further studies must be carried out at
yearly intervals with large sample number, to detect subclinical
thyroid dysfunction cases.
Abstract: Beta-spline is built on G2 continuity which guarantees
smoothness of generated curves and surfaces using it. This curve is
preferred to be used in object design rather than reconstruction. This
study however, employs the Beta-spline in reconstructing a 3-
dimensional G2 image of the Stanford Rabbit. The original data
consists of multi-slice binary images of the rabbit. The result is then
compared with related works using other techniques.
Abstract: The performance of sensor-less controlled induction
motor drive depends on the accuracy of the estimated speed.
Conventional estimation techniques being mathematically complex
require more execution time resulting in poor dynamic response. The
nonlinear mapping capability and powerful learning algorithms of
neural network provides a promising alternative for on-line speed
estimation. The on-line speed estimator requires the NN model to be
accurate, simpler in design, structurally compact and computationally
less complex to ensure faster execution and effective control in real
time implementation. This in turn to a large extent depends on the
type of Neural Architecture. This paper investigates three types of
neural architectures for on-line speed estimation and their
performance is compared in terms of accuracy, structural
compactness, computational complexity and execution time. The
suitable neural architecture for on-line speed estimation is identified
and the promising results obtained are presented.
Abstract: Learning programming is difficult for many learners. Some researches have found that the main difficulty relates to cognitive load. Cognitive overload happens in programming due to the nature of the subject which is intrinisicly over-bearing on the working memory. It happens due to the complexity of the subject itself. The problem is made worse by the poor instructional design methodology used in the teaching and learning process. Various efforts have been proposed to reduce the cognitive load, e.g. visualization softwares, part-program method etc. Use of many computer based systems have also been tried to tackle the problem. However, little success has been made to alleviate the problem. More has to be done to overcome this hurdle. This research attempts at understanding how cognitive load can be managed so as to reduce the problem of overloading. We propose a mechanism to measure the cognitive load during pre instruction, post instruction and in instructional stages of learning. This mechanism is used to help the instruction. As the load changes the instruction is made to adapt itself to ensure cognitive viability. This mechanism could be incorporated as a sub domain in the student model of various computer based instructional systems to facilitate the learning of programming.
Abstract: A simple approach is demonstrated for growing large
scale, nearly vertically aligned ZnO nanowire arrays by thermal
oxidation method. To reveal effect of temperature on growth and
physical properties of the ZnO nanowires, gold coated zinc substrates
were annealed at 300 °C and 400 °C for 4 hours duration in air. Xray
diffraction patterns of annealed samples indicated a set of well
defined diffraction peaks, indexed to the wurtzite hexagonal phase of
ZnO. The scanning electron microscopy studies show formation of
ZnO nanowires having length of several microns and average of
diameter less than 500 nm. It is found that the areal density of wires
is relatively higher, when the annealing is carried out at higher
temperature i.e. at 400°C. From the field emission studies, the values
of the turn-on and threshold field, required to draw emission current
density of 10 μA/cm2 and 100 μA/cm2 are observed to be 1.2 V/μm
and 1.7 V/μm for the samples annealed at 300 °C and 2.9 V/μm and
3.7 V/μm for that annealed at 400 °C, respectively. The field
emission current stability, investigated over duration of more than 2
hours at the preset value of 1 μA, is found to be fairly good in both
cases. The simplicity of the synthesis route coupled with the
promising field emission properties offer unprecedented advantage
for the use of ZnO field emitters for high current density
applications.
Abstract: This paper examines the students’ self-concept among 16- and 17- year- old adolescents in Malaysian secondary schools. Previous studies have shown that positive self-concept played an important role in student adjustment and academic performance during schooling. This study attempts to investigate the factors influencing students’ perceptions toward their own self-concept. A total of 1168 students participated in the survey. This study utilized the CoPs (UM) instrument to measure self-concept. Principal Component Analysis (PCA) revealed three factors: academic selfconcept, physical self-concept and social self-concept. This study confirmed that students perceived certain internal context factors, and revealed that external context factor also have an impact on their self-concept.
Abstract: In this paper, Exp-function method is used for some exact solitary solutions of the generalized Pochhammer-Chree equation. It has been shown that the Exp-function method, with the help of symbolic computation, provides a very effective and powerful mathematical tool for solving nonlinear partial differential equations. As a result, some exact solitary solutions are obtained. It is shown that the Exp-function method is direct, effective, succinct and can be used for many other nonlinear partial differential equations.
Abstract: An approach is offered for more precise definition of base lines- borders in handwritten cursive text and general problems of handwritten text segmentation have also been analyzed. An offered method tries to solve problems arose in handwritten recognition with specific slant or in other words, where the letters of the words are not on the same vertical line. As an informative features, some recognition systems use ascending and descending parts of the letters, found after the word-s baseline detection. In such recognition systems, problems in baseline detection, impacts the quality of the recognition and decreases the rate of the recognition. Despite other methods, here borders are found by small pieces containing segmentation elements and defined as a set of linear functions. In this method, separate borders for top and bottom border lines are found. At the end of the paper, as a result, azerbaijani cursive handwritten texts written in Latin alphabet by different authors has been analyzed.
Abstract: In this paper, the effect of transmission codes on the
performance of coherent square M-ary quadrature amplitude
modulation (CSMQAM) under hybrid selection/maximal-ratio
combining (H-S/MRC) diversity is analysed. The fading channels are
modeled as frequency non-selective slow independent and identically
distributed Rayleigh fading channels corrupted by additive white
Gaussian noise (AWGN). The results for coded MQAM are
computed numerically for the case of (24,12) extended Golay code
and compared with uncoded MQAM under H-S/MRC diversity by
plotting error probabilities versus average signal to noise ratio (SNR)
for various values L and N in order to examine the improvement in
the performance of the digital communications system as the number
of selected diversity branches is increased. The results for no
diversity, conventional SC and Lth order MRC schemes are also
plotted for comparison. Closed form analytical results derived in this
paper are sufficiently simple and therefore can be computed
numerically without any approximations. The analytical results
presented in this paper are expected to provide useful information
needed for design and analysis of digital communication systems
over wireless fading channels.
Abstract: To understand working features of a micro combustor,
a computer code has been developed to study combustion of
hydrogen–air mixture in a series of chambers with same shape aspect
ratio but various dimensions from millimeter to micrometer level.
The prepared algorithm and the computer code are capable of
modeling mixture effects in different fluid flows including chemical
reactions, viscous and mass diffusion effects. The effect of various
heat transfer conditions at chamber wall, e.g. adiabatic wall, with
heat loss and heat conduction within the wall, on the combustion is
analyzed. These thermal conditions have strong effects on the
combustion especially when the chamber dimension goes smaller and
the ratio of surface area to volume becomes larger.
Both factors, such as larger heat loss through the chamber wall
and smaller chamber dimension size, may lead to the thermal
quenching of micro-scale combustion. Through such systematic
numerical analysis, a proper operation space for the micro-combustor
is suggested, which may be used as the guideline for microcombustor
design. In addition, the results reported in this paper
illustrate that the numerical simulation can be one of the most
powerful and beneficial tools for the micro-combustor design,
optimization and performance analysis.
Abstract: Fuel cell is an emerging technology in the field
of renewable energy sources which has the capacity to replace
conventional energy generation sources. Fuel cell utilizes hydrogen
energy to produce electricity. The electricity generated by the fuel
cell can’t be directly used for a specific application as it needs
proper power conditioning. Moreover, the output power fluctuates
with different operating conditions. To get a stable output power
at an economic rate, power conditioning circuit is essential for fuel
cell. This paper implements a two-staged power conditioning unit for
fuel cell based distributed generation using hysteresis current control
technique.
Abstract: This paper describes a novel approach for deriving
modules from protein-protein interaction networks, which combines
functional information with topological properties of the network.
This approach is based on weighted clustering coefficient, which
uses weights representing the functional similarities between the
proteins. These weights are calculated according to the semantic
similarity between the proteins, which is based on their Gene
Ontology terms. We recently proposed an algorithm for identification
of functional modules, called SWEMODE (Semantic WEights for
MODule Elucidation), that identifies dense sub-graphs containing
functionally similar proteins. The rational underlying this approach is
that each module can be reduced to a set of triangles (protein triplets
connected to each other). Here, we propose considering semantic
similarity weights of all triangle-forming edges between proteins. We
also apply varying semantic similarity thresholds between
neighbours of each node that are not neighbours to each other (and
hereby do not form a triangle), to derive new potential triangles to
include in module-defining procedure. The results show an
improvement of pure topological approach, in terms of number of
predicted modules that match known complexes.
Abstract: In this paper, a simple heuristic genetic algorithm is
used for Multistage Multiuser detection in fast fading environments.
Multipath channels, multiple access interference (MAI) and near far
effect cause the performance of the conventional detector to degrade.
Heuristic Genetic algorithms, a rapidly growing area of artificial
intelligence, uses evolutionary programming for initial search, which
not only helps to converge the solution towards near optimal
performance efficiently but also at a very low complexity as
compared with optimal detector. This holds true for Additive White
Gaussian Noise (AWGN) and multipath fading channels.
Experimental results are presented to show the superior performance
of the proposed techque over the existing methods.
Abstract: The problem of frequent itemset mining is considered in this paper. One new technique proposed to generate frequent patterns in large databases without time-consuming candidate generation. This technique is based on focusing on transaction instead of concentrating on itemset. This algorithm based on take intersection between one transaction and others transaction and the maximum shared items between transactions computed instead of creating itemset and computing their frequency. With applying real life transactions and some consumption is taken from real life data, the significant efficiency acquire from databases in generation association rules mining.
Abstract: The plastic forming process of sheet plate takes an
important place in forming metals. The traditional techniques of tool
design for sheet forming operations used in industry are experimental
and expensive methods. Prediction of the forming results,
determination of the punching force, blank holder forces and the
thickness distribution of the sheet metal will decrease the production
cost and time of the material to be formed. In this paper, multi-stage
deep drawing simulation of an Industrial Part has been presented
with finite element method. The entire production steps with
additional operations such as intermediate annealing and springback
has been simulated by ABAQUS software under axisymmetric
conditions. The simulation results such as sheet thickness
distribution, Punch force and residual stresses have been extracted in
any stages and sheet thickness distribution was compared with
experimental results. It was found through comparison of results, the
FE model have proven to be in close agreement with those of
experiment.
Abstract: This research elaborates decision models for product
innovation in the early phases, focusing on one of the most widely
implemented method in marketing research: conjoint analysis and the
related conjoint-based models with special focus on heuristics
programming techniques for the development of optimal product
innovation. The concept, potential, requirements and limitations of
conjoint analysis and its conjoint-based heuristics successors are
analysed and the development of conceptual framework of Genetic
Algorithm (GA) as one of the most widely implemented heuristic
methods for developing product innovations are discussed.
Abstract: The increase on the demand of IT resources diverts
the enterprises to use the cloud as a cheap and scalable solution.
Cloud computing promises achieved by using the virtual machine as a
basic unite of computation. However, the virtual machine pre-defined
settings might be not enough to handle jobs QoS requirements. This
paper addresses the problem of mapping jobs have critical start
deadlines to virtual machines that have predefined specifications.
These virtual machines hosted by physical machines and shared a
fixed amount of bandwidth. This paper proposed an algorithm that
uses the idle virtual machines bandwidth to increase the quote of other
virtual machines nominated as executors to urgent jobs. An algorithm
with empirical study have been given to evaluate the impact of the
proposed model on impatient jobs. The results show the importance
of dynamic bandwidth allocation in virtualized environment and its
affect on throughput metric.
Abstract: TiO2 nanoparticles were synthesized by hydrothermal
method at 180°C from TiOSO4 aqueous solution with1m/l
concentration. The obtained products were coated with silica by
means of a seeded polymerization technique for a coating time of
1440 minutes to obtain well defined TiO2@SiO2 core-shell structure.
The uncoated and coated nanoparticles were characterized by using
X-Ray diffraction technique (XRD), Fourier Transform Infrared
Spectroscopy (FT-IR) to study their physico-chemical properties.
Evidence from XRD and FTIR results show that SiO2 is
homogenously coated on the surface of titania particles. FTIR spectra
show that there exists an interaction between TiO2 and SiO2 and
results in the formation of Ti-O-Si chemical bonds at the interface of
TiO2 particles and SiO2 coating layer. The non linear optical limiting
properties of TiO2 and TiO2@SiO2 nanoparticles dispersed in
ethylene glycol were studied at 532nm using 5ns Nd:YAG laser
pulses. Three-photon absorption is responsible for optical limiting
characteristics in these nanoparticles and it is seen that the optical
nonlinearity is enhanced in core-shell structures when compared with
single counterparts. This effective three-photon type absorption at
this wavelength, is of potential application in fabricating optical
limiting devices.
Abstract: A generic and extendible Multi-Agent Data Mining
(MADM) framework, MADMF (the Multi-Agent Data Mining
Framework) is described. The central feature of the framework is that
it avoids the use of agreed meta-language formats by supporting a
framework of wrappers.
The advantage offered is that the framework is easily extendible,
so that further data agents and mining agents can simply be added to
the framework. A demonstration MADMF framework is currently
available. The paper includes details of the MADMF architecture and
the wrapper principle incorporated into it. A full description and
evaluation of the framework-s operation is provided by considering
two MADM scenarios.