Abstract: Bacterial strains capable of degradation of malathion
from the domestic sewage were isolated by an enrichment culture
technique. Three bacterial strains were screened and identified as
Acinetobacter baumannii (AFA), Pseudomonas aeruginosa (PS1),
and Pseudomonas mendocina (PS2) based on morphological,
biochemical identification and 16S rRNA sequence analysis.
Acinetobacter baumannii AFA was the most efficient malathion
degrading bacterium, so used for further biodegradation study. AFA
was able to grow in mineral salt medium (MSM) supplemented with
malathion (100 mg/l) as a sole carbon source, and within 14 days,
84% of the initial dose was degraded by the isolate measured by high
performance liquid chromatography. Strain AFA could also degrade
other organophosphorus compounds including diazinon, chlorpyrifos
and fenitrothion. The effect of different culture conditions on the
degradation of malathion like inoculum density, other carbon or
nitrogen sources, temperature and shaking were examined.
Degradation of malathion and bacterial cell growth were accelerated
when culture media were supplemented with yeast extract, glucose
and citrate. The optimum conditions for malathion degradation by
strain AFA were; an inoculum density of 1.5x 10^12CFU/ml at 30°C
with shaking. A specific polymerase chain reaction primers were
designed manually using multiple sequence alignment of the
corresponding carboxylesterase enzymes of Acinetobacter species.
Sequencing result of amplified PCR product and phylogenetic
analysis showed low degree of homology with the other
carboxylesterase enzymes of Acinetobacter strains, so we suggested
that this enzyme is a novel esterase enzyme. Isolated bacterial strains
may have potential role for use in bioremediation of malathion
contaminated.
Abstract: In order to better understand the long term
implications of the grout wear failure mode in large-diameter plainsided
grouted connections, a numerical model has been developed
and calibrated that can take advantage of existing operational plant
data to predict the wear accumulation for the actual load conditions
experienced over a given period, thus limiting the requirement for
expensive monitoring systems. This model has been derived and
calibrated based on site structural condition monitoring (SCM) data
and supervisory control and data acquisition systems (SCADA) data
for two operational wind turbine generator substructures afflicted
with this challenge, along with experimentally derived wear rates.
Abstract: In view of a possible application in optical data
storage devices, diffraction grating efficiency of an organic dye, Acid
Fuchsin doped in PMMA matrix was studied under excitation with
CW diode pumped Nd: YAG laser at 532 nm. The open aperture Zscan
of dye doped polymer displayed saturable absorption and the
closed aperture Z-scan of the samples exhibited negative
nonlinearity. The diffraction efficiency of the grating is the ratio of
the intensity of the first order diffracted power to the incident read
beam power. The dye doped polymer films were found to be good
media for recording. It is observed that the formation of gratings
strongly depend on the concentration of dye in the polymer film, the
intensity ratios of the writing beams and the angle between the
writing beams. It has been found that efficient writing can be made at
an angle of 20o and when the intensity ratio of the writing beams is
unity.
Abstract: Karst term is the determiner of a variety of areas or
landforms and unique perspectives that have been formed in result of
the of the ingredients dissolution of rocks constituter by natural
waters. Shiraz area with an area of 5322km2 is located in the simple
folded belt in the southern part of Zagros Mountain of Fars, and is
surrounded with Limestone Mountains (Asmari formation). Shiraz
area is located in Calcareous areas. The infrastructure of this city is
lime and absorbing wells that the city can influence the Limestone
dissolution and those accelerate its rate and increase the cavitation
below the surface. Dasht-e Arjan is a graben, which has been created
as the result of activity of two normal faults in its east and west sides.
It is a complete sample of Karst plains (Polje) which has been created
with the help of tectonic forces (fault) and dissolution process of
water in Asmari limestone formation. It is located 60km. off south
west of Shiraz (on Kazeroon-Shiraz road). In 1971, UNESCO has
recognized this plain as a reserve of biosphere. It is considered as one
of the world’s most beautiful geological phenomena, so that most of
the world’s geologists are interested in visiting this place. The
purpose of this paper is to identify and introduce landscapes of Karst
features shiraz city and Dasht-e Arjan including Karst dissolution
features (Lapiez, Karst springs, dolines, caves, underground caves,
ponors, and Karst valleys), anticlines and synclines, and Arjan Lake.
Abstract: Future flood can be predicted using the probable
maximum flood (PMF). PMF is calculated using the historical
discharge or rainfall data considering the other climatic parameters
remaining stationary. However climate is changing globally and the
key climatic variables are temperature, evaporation, rainfall and sea
level rise are likely to change. To develop scenarios to a basin or
catchment scale these important climatic variables should be
considered. Nowadays scenario based on climatic variables is more
suitable than PMF. Six scenarios were developed for a large Fitzroy
basin and presented in this paper.
Abstract: Container handling problems at container terminals
are NP-hard problems. This paper presents an approach using
discrete-event simulation modeling to optimize solution for storage
space allocation problem, taking into account all various interrelated
container terminal handling activities. The proposed approach is
applied on a real case study data of container terminal at Alexandria
port. The computational results show the effectiveness of the
proposed model for optimization of storage space allocation in
container terminal where 54% reduction in containers handling time
in port is achieved.
Abstract: Domestic goats (Capra hircus) are extremely diverse
species and principal animal genetic resource of the developing
world. These facilitate a persistent supply of meat, milk, fibre, and
skin and are considered as important revenue generators in small
pastoral environments. This study aimed to fingerprint β-LG gene at
PCR-RFLP level in native Saudi goat breeds (Ardi, Habsi and Harri)
in an attempt to have a preliminary image of β-LG genotypic patterns
in Saudi breeds as compared to other foreign breeds such as Indian
and Egyptian. Also, the Phylogenetic analysis was done to investigate
evolutionary trends and similarities among the caprine β-LG gene
with that of the other domestic specie, viz. cow, buffalo and sheep.
Blood samples were collected from 300 animals (100 for each breed)
and genomic DNA was extracted. A fragment of the β-LG gene
(427bp) was amplified using specific primers. Subsequent digestion
with Sac II restriction endonuclease revealed two alleles (A and B)
and three different banding patterns or genotypes i.e. AA, AB and
BB. The statistical analysis showed a general trend that β-LG AA
genotype had higher milk yield than β-LG AB and β-LG BB
genotypes. Nucleotide sequencing of the selected β-LG fragments
was done and submitted to GenBank NCBI (Accession No.
KJ544248, KJ588275, KJ588276, KJ783455, KJ783456 and
KJ874959). Phylogenetic analysis on the basis of nucleotide
sequences of native Saudi goats indicated evolutional similarity with
the GenBank reference sequences of goat, Bubalus bubalis and Bos
taurus. However, the origin of sheep which is the most closely
related from the evolutionary point of view, was located some
distance away.
Abstract: Through this paper we present a method for automatic
generation of ontological model from any data source using Model
Driven Architecture (MDA), this generation is dedicated to the
cooperation of the knowledge engineering and software engineering.
Indeed, reverse engineering of a data source generates a software
model (schema of data) that will undergo transformations to generate
the ontological model. This method uses the meta-models to validate
software and ontological models.
Abstract: Two types of commercial cylindrical lithium ion
batteries (Panasonic 3.4 Ah NCR-18650B and Samsung 2.9 Ah
INR-18650), were investigated experimentally. The capacities of these
samples were individually measured using constant current-constant
voltage (CC-CV) method at different ambient temperatures (-10°C,
0°C, 25°C). Their internal resistance was determined by
electrochemical impedance spectroscopy (EIS) and pulse discharge
methods. The cells with different configurations of parallel connection
NCR-NCR, INR-INR and NCR-INR were charged/discharged at the
aforementioned ambient temperatures. The results showed that the
difference of internal resistance between cells much more evident at
low temperatures. Furthermore, the parallel connection of NCR-NCR
exhibits the most uniform temperature distribution in cells at -10°C,
this feature is quite favorable for the safety of the battery pack.
Abstract: In the present work, detailed analysis on flow characteristics of a pair of immiscible liquids through horizontal pipeline is simulated by using ANSYS FLUENT 6.2. Moderately viscous oil and water (viscosity ratio = 107, density ratio = 0.89 and interfacial tension = 0.024 N/m) have been taken as system fluids for the study. Volume of Fluid (VOF) method has been employed by assuming unsteady flow, immiscible liquid pair, constant liquid properties, and co-axial flow. Meshing has been done using GAMBIT. Quadrilateral mesh type has been chosen to account for the surface tension effect more accurately. From the grid independent study, we have selected 47037 number of mesh elements for the entire geometry. Simulation successfully predicts slug, stratified wavy, stratified mixed and annular flow, except dispersion of oil in water, and dispersion of water in oil. Simulation results are validated with horizontal literature data and good conformity is observed. Subsequently, we have simulated the hydrodynamics (viz., velocity profile, area average pressure across a cross section and volume fraction profile along the radius) of stratified wavy and annular flow at different phase velocities. The simulation results show that in the annular flow, total pressure of the mixture decreases with increase in oil velocity due to the fact that pipe cross section is completely wetted with water. Simulated oil volume fraction shows maximum at the centre in core annular flow, whereas, in stratified flow, maximum value appears at upper side of the pipeline. These results are in accord with the actual flow configuration. Our findings could be useful in designing pipeline for transportation of crude oil.
Abstract: Poly(lactic acid) (PLA) is a biodegradable polymer
which has good mechanical properties, however, its brittleness limits
its usage especially in packaging materials. Therefore, in this work,
PLA based polyurethane films were prepared by synthesizing with
different types of isocyanates; methylene diisocyanate (MDI) and
hexamethylene diisocyanates (HDI). For this purpose, PLA based
polyurethane must have good strength and flexibility. Therefore,
polycaprolactone which has better flexibility were prepared with
PLA. An effective way to endow polylactic acid with toughness is
through chain-extension reaction of the polylactic acid pre-polymer
with polycaprolactone used as chain extender. Polyurethane prepared
from MDI showed brittle behaviour, while, polyurethane prepared
from HDI showed flexibility at same concentrations.
Abstract: In recent years many finite elements have been
developed for plate bending analysis. The formulated elements are
based on the strain based approach. This approach leads to the
representation of the displacements by higher order polynomial terms
without the need for the introduction of additional internal and
unnecessary degrees of freedom. Good convergence can also be
obtained when the results are compared with those obtained from the
corresponding displacement based elements, having the same total
number of degrees of freedom. Furthermore, the plate bending
elements are free from any shear locking since they converge to the
Kirchhoff solution for thin plates contrarily for the corresponding
displacement based elements. In this paper the efficiency of the strain
based approach compared to well known displacement formulation is
presented. The results obtained by a new formulated plate bending
element based on the strain approach and Kirchhoff theory are
compared with some others elements. The good convergence of the
new formulated element is confirmed.
Abstract: The analysis and design of thin shell structures is a topic of interest in a variety of engineering applications. In structural mechanics problems the analyst seeks to determine the distribution of stresses throughout the structure to be designed. It is also necessary to calculate the displacements of certain points of the structure to ensure that specified allowable values are not exceeded. In this paper a comparative study between displacement and strain based finite elements applied to the analysis of some thin shell structures is presented. The results obtained from some examples show the efficiency and the performance of the strain based approach compared to the well known displacement formulation.
Abstract: Many organizations are opting to adopt Open Source Software (OSS) as it is the current trend to rely on each other rather than on companies (Software vendors). It is a clear shift from organizations to individuals, the concept being to rely on collective participation rather than companies/vendors.
The main objectives of this research are 1) to identify the current level of OSS usage in Sultan Qaboos University; 2) to identify the potential benefits of using OSS in educational institutes; 3) to identify the OSS applications that are most likely to be used within an educational institute; 4) to identify the existing and potential barriers to the successful adoption of OSS in education.
To achieve these objectives a two-stage research method was conducted. First a rigorous literature review of previously published material was performed (interpretive/descriptive approach), and then a set of interviews were conducted with the IT professionals at Sultan Qaboos University in Oman in order to explore the extent and nature of their usage of OSS.
Abstract: In communication systems, frequency jump is a serious problem caused by the oscillators used. Kalman filters are used to detect that jump, despite the tradeoff between the noise level and the speed of the detection. In this paper, an improvement is introduced in the Kalman filter, through a nonlinear change in the bandwidth of the filter. Simulation results show a considerable improvement in the filter speed with a very low noise level. Additionally, the effect on the response to false alarms is also presented and false alarm rate show improvement.
Abstract: The aesthetic qualities and the versatility of reinforced
concrete have made it a popular choice for many architects and
structural engineers. Therefore, the exploration of natural materials
such as gravels and sands as well as lime-stone for cement production
is increasing to produce a concrete material. The exploration must
affect to the environment. Therefore, the using of the concrete
materials should be as efficient as possible. According to its natural
behavior of the concrete material, it is strong in compression and weak
in tension. Therefore the contribution of the tensile stresses of the
concrete to the flexural capacity of the beams is neglected. However,
removing of concrete on tension zone affects to the decreasing of
flexural capacity. Introduce the strut action of truss structures may an
alternative to solve the decreasing of flexural capacity. A series of
specimens were prepared to clarify the effect of the truss structures in
the concrete beams without concrete on the tension zone. Results
indicated that the truss system is necessary for the external reinforced
concrete beams. The truss system of concrete beam without concrete
on tension zone (BR) could develop almost same capacity to the
normal beam (BN). It can be observed also that specimens BR has
lower number of cracks than specimen BN. This may be caused by the
fact that there was no bonding effect on the tensile reinforcement on
specimen BR to distribute the cracks.
Abstract: A variety of routing techniques are available to develop surface runoff hydrographs from rainfall. The selection of runoff routing method is very vital as it is directly related to the type of watershed and the required degree of accuracy. There are different modelling softwares available to explore the rainfall-runoff process in urban areas. XPSTORM, a link-node based, integrated stormwater modelling software, has been used in this study for developing surface runoff hydrograph for a Golf course area located in Rockhampton in Central Queensland in Australia. Four commonly used methods, namely SWMM runoff, Kinematic wave, Laurenson, and Time-Area are employed to generate runoff hydrograph for design storm of this study area. In runoff mode of XPSTORM, the rainfall, infiltration, evaporation and depression storage for subcatchments were simulated and the runoff from the subcatchment to collection node was calculated. The simulation results are presented, discussed and compared. The total surface runoff generated by SWMM runoff, Kinematic wave and Time-Area methods are found to be reasonably close, which indicates any of these methods can be used for developing runoff hydrograph of the study area. Laurenson method produces a comparatively less amount of surface runoff, however, it creates highest peak of surface runoff among all which may be suitable for hilly region. Although the Laurenson hydrograph technique is widely acceptable surface runoff routing technique in Queensland (Australia), extensive investigation is recommended with detailed topographic and hydrologic data in order to assess its suitability for use in the case study area.
Abstract: Owing to the lack of synchronization between the solar energy availability and the heat demands in a specific application, the energy storing sub-system is necessary to maintain the continuity of thermal process. The present work is dealing with an active solar heating storing system in which an air solar collector is connected to storing unit where this energy is distributed and provided to the heated space in a controlled manner. The solar collector is a box type absorber where the air flows between a number of vanes attached between the collector absorber and the bottom plate. This design can improve the efficiency due to increasing the heat transfer area exposed to the flowing air, as well as the heat conduction through the metal vanes from the top absorbing surface. The storing unit is a packed bed type where the air is coming from the air collector and circulated through the bed in order to add/remove the energy through the charging / discharging processes, respectively. The major advantage of the packed bed storage is its high degree of thermal stratification. Numerical solution of the packed bed energy storage is considered through dividing the bed into a number of equal segments for the bed particles and solved the energy equation for each segment depending on the neighbor ones. The studied design and performance parameters in the developed simulation model including, particle size, void fraction, etc. The final results showed that the collector efficiency was fluctuated between 55%-61% in winter season (January) under the climatic conditions of Misurata in Libya. Maximum temperature of 52ºC is attained at the top of the bed while the lower one is 25ºC at the end of the charging process of hot air into the bed. This distribution can satisfy the required load for the most house heating in Libya.
Abstract: In this study, fish bone waste was used as a new
catalyst for biodiesel production. Instead of discarding the fish bone
waste, it will be utilized as a source for catalyst that can provide
significant benefit to the environment. Also, it can be substitute as a
calcium oxide source instead of using eggshell, crab shell and snail
shell. The XRD and SEM analysis proved that calcined fish bone
contains calcium oxide, calcium phosphate and hydroxyapatite. The
catalyst was characterized using Scanning Electron Microscope
(SEM) and X-ray Diffraction (XRD).
Abstract: The intense use of the web has made it a very changing environment, its content is in permanent evolution to adapt to the demands. The standards have accompanied this evolution by passing from standards that regroup data with their presentations without any structuring such as HTML, to standards that separate both and give more importance to the structural aspect of the content such as XML standard and its derivatives. Currently, with the appearance of the Semantic Web, ontologies become increasingly present on the web and standards that allow their representations as OWL and RDF/RDFS begin to gain momentum. This paper provided an automatic method that converts XML schema document to ontologies represented in OWL.