Abstract: The goal of this paper is to examine the effects of laser
radiation on the skin wound healing using infrared thermography as
non-invasive method for the monitoring of the skin temperature
changes during laser treatment. Thirty Wistar rats were used in this
study. A skin lesion was performed at the leg on all rats. The animals
were exposed to laser radiation (λ = 670 nm, P = 15 mW, DP = 16.31
mW/cm2) for 600 s. Thermal images of wound were acquired before
and after laser irradiation. The results have demonstrated that the
tissue temperature decreases from 35.5±0.50°C in the first treatment
day to 31.3±0.42°C after the third treatment day. This value is close
to the normal value of the skin temperature and indicates the end of
the skin repair process. In conclusion, the improvements in the
wound healing following exposure to laser radiation have been
revealed by infrared thermography.
Abstract: Knowledge of food resource of the houbara which an
endangered species would be a important step toward the
preservation of this bird. Adequate study has not been done in this
field and therefore the food sources of the houbara during the
brooding season was studied in the central steppe of Iran. In order to
determine the density of insect in plant communities the pitfall trap
was used , positioned in five linear transects divided between plant
communities and in two repetitions. The results showed that the
among communities there was a significant difference in term of the
number beetles and ants ( p= 0.01, F2, 29= 4.66) collectively. Also
bush steppe habitat had a higher arthropoda density in comparison
with the shrub steppe habitat. Considering that most houbara nests
were found in the bush steppe habitat .It seems this habitat provides
the most available food supply for the houbara chicks.
Abstract: In this paper a study on the vibration of thin
cylindrical shells with ring supports and made of functionally
graded materials (FGMs) composed of stainless steel and
nickel is presented. Material properties vary along the
thickness direction of the shell according to volume fraction
power law. The cylindrical shells have ring supports which are
arbitrarily placed along the shell and impose zero lateral
deflections. The study is carried out based on third order shear
deformation shell theory (T.S.D.T). The analysis is carried out
using Hamilton-s principle. The governing equations of motion of
FGM cylindrical shells are derived based on shear deformation
theory. Results are presented on the frequency characteristics,
influence of ring support position and the influence of boundary
conditions. The present analysis is validated by comparing results
with those available in the literature.
Abstract: An explicit axisymmetrical FE methodology is
developed here to study the particle temperature arising in WC-Co
particle on an AISI 1045 steel substrate. Parameters of constitutive
Johnson-cook model were used for simulation. The results show that
particle velocity and kinetic energy have important role in
temperature arising of particles.
Abstract: In the present work, study of the vibration of thin cylindrical shells made of a functionally gradient material (FGM) composed of stainless steel and nickel is presented. Material properties are graded in the thickness direction of the shell according to volume fraction power law distribution. The objective is to study the natural frequencies, the influence of constituent volume fractions and the effects of boundary conditions on the natural frequencies of the FG cylindrical shell. The study is carried out using third order shear deformation shell theory. The governing equations of motion of FG cylindrical shells are derived based on shear deformation theory. Results are presented on the frequency characteristics, influence of constituent volume fractions and the effects of free-free boundary conditions.
Abstract: Mixed convection in two-dimensional shallow rectangular enclosure is considered. The top hot wall moves with constant velocity while the cold bottom wall has no motion. Simulations are performed for Richardson number ranging from Ri = 0.001 to 100 and for Reynolds number keeping fixed at Re = 408.21. Under these conditions cavity encompasses three regimes: dominating forced, mixed and free convection flow. The Prandtl number is set to 6 and the effects of cavity inclination on the flow and heat transfer are studied for different Richardson number. With increasing the inclination angle, interesting behavior of the flow and thermal fields are observed. The streamlines and isotherm plots and the variation of the Nusselt numbers on the hot wall are presented. The average Nusselt number is found to increase with cavity inclination for Ri ³ 1 . Also it is shown that the average Nusselt number changes mildly with the cavity inclination in the dominant forced convection regime but it increases considerably in the regime with dominant natural convection.
Abstract: In order to evaluate the Effects of dual inoculation of
Azotobacter and Mycorrhiza with Nitrogen and Phosphorus levels on
yield and yield components of spring safflower, this study was
carried out in field of Farahan university in Markazi province in
2007. A factorial in a randomized complete block design with three
replications was used inoculation of Azotobacter (with inoculation
and without inoculation) and Mycorrhiza (with inoculation and
without inoculation ) with Nitrogen and Phosphorus levels [F0= N0+
P0 (kg.ha-1), F1= N50+ P25(kg.ha-1), F2= N100+ P50(kg.ha-1) and
F3= N150+ P75 (kg.ha-1)] on spring safflower (cultivar IL-111). In
this study characteristics such as: Harvest index, Hectolitre weight,
Root dry weight, Seed yield, Mycorrhizal Colonization Root,
Number of days to maturity were assessed. Results indicated that
treatment (A0M1F3) with grain yield (1556 kg.ha-1) and treatment
(A0M1F0) with grain yield (918 kg.ha-1) were significantly superior
to the other treatments and according to calculated, inoculation seeds
in plantig date with Azotobacter and Mycorrhiza to cause increase
grain yield about 5/38 percentage. we can by inoculation safflower
seeds with Azotobacter and Mycorrhiza too easily at the time sowing
date. The purpose of this research, study and evaluation the role of
biological fixation N and P, to provide for feeds plants.
Abstract: Prediction of highly non linear behavior of suspended
sediment flow in rivers has prime importance in the field of water
resources engineering. In this study the predictive performance of
two Artificial Neural Networks (ANNs) namely, the Radial Basis
Function (RBF) Network and the Multi Layer Feed Forward (MLFF)
Network have been compared. Time series data of daily suspended
sediment discharge and water discharge at Pari River was used for
training and testing the networks. A number of statistical parameters
i.e. root mean square error (RMSE), mean absolute error (MAE),
coefficient of efficiency (CE) and coefficient of determination (R2)
were used for performance evaluation of the models. Both the models
produced satisfactory results and showed a good agreement between
the predicted and observed data. The RBF network model provided
slightly better results than the MLFF network model in predicting
suspended sediment discharge.
Abstract: One of the major problems in liberalized power
markets is loss allocation. In this paper, a different method for
allocating transmission losses to pool market participants is
proposed. The proposed method is fundamentally based on
decomposition of loss function and current projection concept. The
method has been implemented and tested on several networks and
one sample summarized in the paper. The results show that the
method is comprehensive and fair to allocating the energy losses of a
power market to its participants.
Abstract: Traditional principal components analysis (PCA)
techniques for face recognition are based on batch-mode training
using a pre-available image set. Real world applications require that
the training set be dynamic of evolving nature where within the
framework of continuous learning, new training images are
continuously added to the original set; this would trigger a costly
continuous re-computation of the eigen space representation via
repeating an entire batch-based training that includes the old and new
images. Incremental PCA methods allow adding new images and
updating the PCA representation. In this paper, two incremental
PCA approaches, CCIPCA and IPCA, are examined and compared.
Besides, different learning and testing strategies are proposed and
applied to the two algorithms. The results suggest that batch PCA is
inferior to both incremental approaches, and that all CCIPCAs are
practically equivalent.
Abstract: This paper presents a new adaptive DMC controller
that improves the controller performance in case of plant-model
mismatch. The new controller monitors the plant measured output,
compares it with the model output and calculates weights applied to
the controller move. Simulations show that the new controller can
help improve control performance and avoid instability in case of
severe model mismatches.
Abstract: Safety Health and Environment Code of Practice (SHE
COP) was developed to help road transportation operators to manage
its operation in a systematic and safe manner. A study was conducted
to determine the effectiveness of SHE COP implementation during
non-OPS period. The objective of the study is to evaluate the
implementations of SHE COP among bus operators during wee hour
operations. The data was collected by completing a set of checklist
after observing the activities during pre departure, during the trip, and
upon arrival. The results show that there are seven widely practiced
SHE COP elements. 22% of the buses have average speed exceeding
the maximum permissible speed on the highways (90 km/h), with
13% of the buses were travelling at the speed of more than 100 km/h.
The statistical analysis shows that there is only one significant
association which relates speeding with prior presence of
enforcement officers.
Abstract: This paper presents an approach for the determination of the optimal cutting parameters (spindle speed, feed rate, depth of cut and engagement) leading to minimum surface roughness in face milling of high silicon stainless steel by coupling neural network (NN) and Electromagnetism-like Algorithm (EM). In this regard, the advantages of statistical experimental design technique, experimental measurements, artificial neural network, and Electromagnetism-like optimization method are exploited in an integrated manner. To this end, numerous experiments on this stainless steel were conducted to obtain surface roughness values. A predictive model for surface roughness is created by using a back propogation neural network, then the optimization problem was solved by using EM optimization. Additional experiments were performed to validate optimum surface roughness value predicted by EM algorithm. It is clearly seen that a good agreement is observed between the predicted values by EM coupled with feed forward neural network and experimental measurements. The obtained results show that the EM algorithm coupled with back propogation neural network is an efficient and accurate method in approaching the global minimum of surface roughness in face milling.
Abstract: Khatunabad area is situated geologically in Urmieh-
Dokhtar magmatic belt in NW of Iran. In this research, studied area
has been investigated in order to recognize the potential copper and
molybdenum-bearing target areas. The survey layers include the
lithologic units, alteration, geochemical result, tectonics and copper
and molybdenum occurrence. As an accurate decision can have a
considerable effect on exploration plans, so in this efforts have been
made to make use of new combination method. For this purpose, the
analytical hierarchy process was used and revealed highly potential
copper and molybdenum mineralization areas. Based on achieved
results, geological perspective in north of studied area is appropriate
for advance stage, especially for subsurface exploration in future.
Abstract: This paper presents a practical scheme that can be used for allocating the transmission loss to generators and loads. In this scheme first the share of a generator or load on the current through a branch is determined using Z-bus modified matrix. Then the current components are decomposed and the branch loss allocation is obtained. A motivation of proposed scheme is to improve the results of Z-bus method and to reach more fair allocation. The proposed scheme has been implemented and tested on several networks. To achieve practical and applicable results, the proposed scheme is simulated and compared on the transmission network (400kv) of Khorasan region in Iran and the 14-bus standard IEEE network. The results show that the proposed scheme is comprehensive and fair to allocating the energy losses of a power market to its participants.
Abstract: The aim of this paper is to present the kinematic
analysis and mechanism design of an assistive robotic leg for
hemiplegic and hemiparetic patients. In this work, the priority is to
design and develop the lightweight, effective and single driver
mechanism on the basis of experimental hip and knee angles- data for
walking speed of 1 km/h. A mechanism of cam-follower with three
links is suggested for this purpose. The kinematic analysis is carried
out and analysed using commercialized MATLAB software based on
the prototype-s links sizes and kinematic relationships. In order to
verify the kinematic analysis of the prototype, kinematic analysis data
are compared with the experimental data. A good agreement between
them proves that the anthropomorphic design of the lower extremity
exoskeleton follows the human walking gait.
Abstract: Study of the vibration cylindrical shells made of
a functionally gradient material (FGM) composed of stainless
steel and nickel is important. Material properties are graded in
the thickness direction of the shell according to volume
fraction power law distribution. The objective is to study the
natural frequencies, the influence of constituent volume
fractions and the effects of boundary conditions on the natural
frequencies of the FG cylindrical shell. The study is carried
out using third order shear deformation shell theory. The
governing equations of motion of FG cylindrical shells are
derived based on shear deformation theory. Results are
presented on the frequency characteristics, influence of
constituent volume fractions and the effects of clampedclamped
boundary conditions.
Abstract: The Mahin area is a part of Tarom- Hashtjin zone that
located in west of Qazvin province in northwest of Iran. Many copper
and base metals ore deposits are hosted by this zone. High potential
localities identification in this area is very necessary. The objective of
this research, is finding hydrothermal alteration zones by remote
sensing methods and best processing technique of Advanced
Spaceborne Thermal Emission and Reflection Radiometer (ASTER)
data. Different methods such as band ratio, Principal Component
Analysis (PCA), Minimum Noise Fraction (MNF) and Least Square
Fit (LS-Fit) were used for mapping hydrothermal alteration zones.
Abstract: In the present work, study of the vibration of thin cylindrical shells made of a functionally gradient material (FGM) composed of stainless steel and nickel is presented. Material properties are graded in the thickness direction of the shell according to volume fraction power law distribution. The objective is to study the natural frequencies, the influence of constituent volume fractions and the effects of boundary conditions on the natural frequencies of the FG cylindrical shell. The study is carried out using third order shear deformation shell theory. The analysis is carried out using Hamilton's principle. The governing equations of motion of FG cylindrical shells are derived based on shear deformation theory. Results are presented on the frequency characteristics, influence of constituent volume fractions and the effects of clamped-free boundary conditions
Abstract: Nozzle is the main part of various spinning systems
such as air-jet and Murata air vortex systems. Recently, many
researchers worked on the usage of the nozzle on different spinning
systems such as conventional ring and compact spinning systems. In
these applications, primary purpose is to improve the yarn quality. In
present study, it was produced the yarns with two different nozzle
types and determined the changes in yarn properties. In order to
explain the effect of the nozzle, airflow structure in the nozzle was
modelled and airflow variables were determined. In numerical
simulation, ANSYS 12.1 package program and Fluid Flow (CFX)
analysis method was used. As distinct from the literature, Shear
Stress Turbulent (SST) model is preferred. And also air pressure at
the nozzle inlet was measured by electronic mass flow meter and
these values were used for the simulation of the airflow. At last, the
yarn was modelled and the area from where the yarn is passing was
included to the numerical analysis.