Abstract: This paper deals with stability analysis for synchronous reluctance motors drive. Special attention is paid to the transient performance with variations in motor's parameters such as Ld and Rs. A study of the dynamic control using d-q model is presented first in order to clarify the stability of the motor drive system. Based on the experimental parameters of the synchronous reluctance motor, this paper gives some simulation results using MATLAB/SIMULINK software packages. It is concluded that the motor parameters, especially Ld, affect the estimator stability and hence the whole drive system.
Abstract: In this study, ZnO nano rods and ZnO ultrafine particles were synthesized by Gel-casting method. The synthesized ZnO powder has a hexagonal zincite structure. The ZnO aggregates with rod-like morphology are typically 1.4 μm in length and 120 nm in diameter, which consist of many small nanocrystals with diameters of 10 nm. Longer wires connected by many hexahedral ZnO nanocrystals were obtained after calcinations at the temperature over 600° C.The crystalline structures and morphologies of the powder have been characterized by X-ray diffraction(XRD) and Scaning electron microscopy (SEM).The result shows that the different preparation conditions such as concentration H2O, calcinations time and calcinations temperature have a lot of influences upon the properties of nano ZnO powders, an increase in the temperature of the calcinations results in an increase of the grain size and also the increase of the calcinations time in high temperature makes the size of the grains bigger. The existences of extra watter prevent nano grains from improving like rod morphology. We have obtained the smallest grain size of ZnO powder by controlling the process conditions. Finally In a suitable condition, a novel nanostructure, namely bi-rod-like ZnO nano rods was found which is different from known ZnO nanostructures.
Abstract: In industrial scale of Gas to Liquid (GTL) process in
Fischer-Tropsch (FT) synthesis, a part of reactor outlet gases such as
CO2 and CH4 as side reaction products, is usually recycled. In this
study, the influence of CO2 and CH4 on the performance and
selectivity of Co-Ru/Al2O3 catalyst is investigated by injection of
these gases (0-20 vol. % of feed) to the feed stream. The effect of
temperature and feed flow rate, are also inspected. The results show
that low amounts of CO2 in the feed stream, doesn`t change the
catalyst activity significantly but increasing the amount of CO2 (more
than 10 vol. %) cause the CO conversion to decrease and the
selectivity of heavy components to increase. Methane acts as an inert
gas and doesn`t affect the catalyst performance. Increasing feed flow
rate has negative effect on both CO conversion and heavy component
selectivity. By raising the temperature, CO conversion will increase
but there are more volatile components in the product. The effect of
CO2 on the catalyst deactivation is also investigated carefully and a
mechanism is suggested to explain the negative influence of CO2 on
catalyst deactivation.
Abstract: This paper presents the Literature Review of carbon fiber reinforced polymer (CFRP) strips to reinforced concrete (RC) as a strengthening solution for T-beams. Although a great deal of research has been carried out on Rectangular beams strengthened with Fibre-Reinforced Polymer composites (FRP), Fiber reinforced polymer (FRP) composites have been increasingly studied for their application in the flexural or shear strengthening of reinforced concrete (RC) members. A detailed discussion of the shearstrengthening repair with FRP is undertaken. This paper will be limited to research of CFRP material externally bonded to the tensile face of concrete beams. In particular, research studying the effect of externally applied CFRP materials on the shear performance of reinforced concrete beams will be reported.
Abstract: This paper reports the findings of a research
conducted to evaluate the ownership and usage of technology devices
within Distance Education students- according to their age. This
research involved 45 Distance Education students from USM
Universiti Sains Malaysia (DEUSM) as its respondents. Data was
collected through questionnaire that had been developed by the
researchers based on some literature review. The data was analyzed
to find out the frequencies of respondents agreements towards
ownership of technology devices and the use of technology devices.
The findings shows that all respondents own mobile phone and
majority of them reveal that they use mobile on regular basis. The
student in the age 30-39 has the heist ownership of the technology
devices.
Abstract: This survey highlights a number of important issues
which relate to the needs to counseling for distance learners studying
at the School of Distance Education in University science Malaysia
(DEUSM) according to their gender. Data were obtained by selfreport
questionnaire that had been developed by the researchers in
counseling and educational psychology and interviews were take
place. 116 voluntary respondents complete the Questionnaire and
returned it back during new student-s registration week.64% of the
respondents were female and 52% were males that means
55%ofthem were females and 45% were males. The data was
analyzed to find out the frequencies of respondents agreements of the
items. The average of the female was 18 and the average of the male
was 19.6 by using t- test there is no significant values between the
genders. The findings show that respondents have needs for
counseling. (22) Significant needs for mails (DEUSM) the highest
was their families complain about the amount of time they spend at
work. (11) Significant needs for females the highest was they
convinced themselves that they only need 4 to 5 hours of sleep per
night.
Abstract: This paper presents a controller design technique for
Synchronous Reluctance Motor to improve its dynamic performance
with fast response and high accuracy. The sliding mode control is the
most attractive and suitable method to use for this purpose, since it is
simple in design and for its insensitivity to parameter variations or
external disturbances. When this method implemented it yields fast
dynamic response without overshoot and a zero steady-state error.
The current loop control with decentralized sliding mode is presented
in this paper. The mathematical model for the synchronous machine,
the inverter and the controller is developed. The stability of the
sliding mode controller is analyzed. Simulation of synchronous
reluctance motor and the controller with PWM-inverter has been
curried out, using the SIMULINK software package of MATLAB.
Simulation results are presented to show the effectiveness of the
approach.
Abstract: In the article the experience of principle new
technology development of ethnopsychological experiment on the
basis of using other virtual independent experimental variables is
presented. It is shown that ethnic prejudices are the result of forming
and development of specific semantic barriers, arising up in the
conditions of interethnic co-operation and people-s communication.
Their overcoming is more successful in the conditions of the special
organized process of teaching in a polyethnic environment,
characteristic for the modern institute
Abstract: Most standard software development methodologies
are often not applied to software projects in many developing
countries of the world. The approach generally practice is close to
what eXtreme Programming (XP) is likely promoting, just keep
coding and testing as the requirement evolves. XP is an agile
software process development methodology that has inherent
capability for improving efficiency of Business Software
Development (BSD). XP can facilitate Business-to-Development
(B2D) relationship due to its customer-oriented advocate. From
practitioner point of view, we applied XP to BSD and result shows
that customer involvement has positive impact on productivity, but
can as well frustrate the success of the project. In an effort to
promote software engineering practice in developing countries of
Africa, we present the experiment performed, lessons learned,
problems encountered and solution adopted in applying XP
methodology to BSD.
Abstract: Seasonal survey of freshwater snails in different water
courses in Egypt during two successive years included 13 snail
species. They represented by Biomphalaria alexandrina, Bulinus
truncatus, Physa acuta, Helisoma duryi, Lymnaea natalensis,
Planorbis pantries, Cleopatra bulimoides, Lanistes carinatus,
Bellamya unicolor, Melanoides tuberculata, Theodoxus niloticus,
Succinia cleopatra and Valvata nilotica. B. alexandrina was most
abundant during autumn and spring represented by 26and14
snails/site, respectively. B. truncatus was most abundant during
winter (7.7and3.6snails/site) of the two years, respectively. L.
natalensis was represented by 7snails/site in summer. The tolerance
of different snail species to the chemical elements was determined
seasonally and correlated to their abundance. In spring, autumn and
winter, B. alexandrina was significantly found to live under the
highest level of Pb, Cd,Cu, Na, K and Ca concentrations than the
other species (p
Abstract: Transliteration is frequently used especially in writing geographic denominations, personal names (onyms) etc. Proper names (onyms) of all languages must sound similarly in translated works as well as in scientific projects and works written in mother tongue, because we can get introduced with the nation, its history, culture, traditions and other spiritual values through the onyms of that nation. Therefore it is necessary to systematize the different transliterations of onyms of foreign languages. This paper is dedicated to the problem of making the project of transliterating Kazakh onyms into Arabic. In order to achieve this goal we use scientific or practical types of transliteration. Because in this type of transliteration provides easy reading writing source language's texts in the target language without any diacritical symbols, it is limited by the target language's alphabetic system.
Abstract: Security has been an important issue and concern in the
smart home systems. Smart home networks consist of a wide range of
wired or wireless devices, there is possibility that illegal access to
some restricted data or devices may happen. Password-based
authentication is widely used to identify authorize users, because this
method is cheap, easy and quite accurate. In this paper, a neural
network is trained to store the passwords instead of using verification
table. This method is useful in solving security problems that
happened in some authentication system. The conventional way to
train the network using Backpropagation (BPN) requires a long
training time. Hence, a faster training algorithm, Resilient
Backpropagation (RPROP) is embedded to the MLPs Neural
Network to accelerate the training process. For the Data Part, 200
sets of UserID and Passwords were created and encoded into binary
as the input. The simulation had been carried out to evaluate the
performance for different number of hidden neurons and combination
of transfer functions. Mean Square Error (MSE), training time and
number of epochs are used to determine the network performance.
From the results obtained, using Tansig and Purelin in hidden and
output layer and 250 hidden neurons gave the better performance. As
a result, a password-based user authentication system for smart home
by using neural network had been developed successfully.
Abstract: Abai Kunanbayev is famous for being enlightener,
composer, interpreter, social agent, philosopher, reformer, who
wanted to enrich Kazakh literature by emergence with Russian and
European culture, and also as a founder of Kazakh written literary
language. Abai Kunanbayev was born in 1845 in East Kazakhstan
area and passed away in 1904 in his hometown. His oeuvre absorbed
and reflected all changes in the life of Kazakh society of the second
half of XIX century. Because ХІХ century, especially its second half,
was an important transition period for Kazakhstan, which radically
changed traditional way of Kazakh society and predetermined further
development in consequence of activation of Russian colonial policy
and approval of commodity-money relations in Steppe Land.Abai
Kunanbayev, besides Arabic and Persian common words and
loanwords from Quran in his words of edification, had used a lot of
words of Arabic, Persian, Latin, Russian, Nogai, Shaghatai, Polish,
Greek, Turkish, which are used in the Kazakh language.
Abstract: The task of face recognition has been actively
researched in recent years. This paper provides an up-to-date review of major human face recognition research. We first present an
overview of face recognition and its applications. Then, a literature review of the most recent face recognition techniques is presented.
Description and limitations of face databases which are used to test
the performance of these face recognition algorithms are given. A
brief summary of the face recognition vendor test (FRVT) 2002, a
large scale evaluation of automatic face recognition technology, and
its conclusions are also given. Finally, we give a summary of the research results.
Abstract: Quantitative precipitation forecast (QPF) from
atmospheric model as input to hydrological model in an integrated
hydro-meteorological flood forecasting system has been operational
in many countries worldwide. High-resolution numerical weather
prediction (NWP) models with grid cell sizes between 2 and 14 km
have great potential in contributing towards reasonably accurate QPF.
In this study the potential of two NWP models to forecast
precipitation for a flood-prone area in a tropical region is examined.
The precipitation forecasts produced from the Fifth Generation Penn
State/NCAR Mesoscale (MM5) and Weather Research and
Forecasting (WRF) models are statistically verified with the observed
rain in Kelantan River Basin, Malaysia. The statistical verification
indicates that the models have performed quite satisfactorily for low
and moderate rainfall but not very satisfactory for heavy rainfall.
Abstract: This paper presents the design and analysis of a parallel
connected inverter configuration of. The configuration consists of
parallel connected three-phase dc/ac inverter. Series resistors added
to the inverter output to maintain same current in each inverter of the
two parallel inverters, and to reduce the circulating current in the
parallel inverters to the minimum. High frequency third harmonic
injection PWM (THIPWM) employed to reduce the total harmonic
distortion and to make maximum use of the voltage source. DSP was
used to generate the THIPWM and the control algorithm for the
converter. Selected experimental results have been shown to validate
the proposed system.
Abstract: This study investigates the capacity of granular
activated carbon (GAC) for the storage of methane through the
equilibrium adsorption. An experimental apparatus consist of a dual
adsorption vessel was set up for the measurement of equilibrium
adsorption of methane on GAC using volumetric technique (pressure
decay). Experimental isotherms of methane adsorption were
determined by the measurement of equilibrium uptake of methane in
different pressures (0-50 bar) and temperatures (285.15-328.15°K).
The experimental data was fitted to Freundlich and Langmuir
equations to determine the model isotherm. The results show that the
experimental data is equally well fitted by the both model isotherms.
Using the experimental data obtained in different temperatures the
isosteric heat of methane adsorption was also calculated by the
Clausius-Clapeyron equation from the Sips isotherm model. Results
of isosteric heat of adsorption show that decreasing temperature or
increasing methane uptake by GAC decrease the isosteric heat of
methane adsorption.
Abstract: An Automated Rapid Maxillary Expander (ARME) is
a specially designed microcontroller-based orthodontic appliance to
overcome the shortcomings imposed by the traditional maxillary
expansion appliances. This new device is operates by automatically
widening the maxilla (upper jaw) by expanding the midpalatal suture
[1]. The ARME appliance that has been developed is a combination
of modified butterfly expander appliance, micro gear, micro motor,
and microcontroller to automatically produce light and continuous
pressure to expand the maxilla. For this study, the functionality of the
system is verified through laboratory tests by measure the forced
applied to the teeth each time the maxilla expands. The laboratory
test results show that the developed appliance meets the desired
performance specifications consistently.
Abstract: The role of entrepreneurs in generating the economy is
very important. Thus, nurturing entrepreneurship skills among
society is very crucial and should start from the early age. One of the
methods is to teach through game such as board game. Game
provides a fun and interactive platform for players to learn and play.
Besides that as today-s world is moving towards Islamic approach in
terms of finance, banking and entertainment but Islamic based game
is still hard to find in the market especially games on
entrepreneurship. Therefore, there is a gap in this segment that can be
filled by learning entrepreneurship through game. The objective of
this paper is to develop an entrepreneurship digital-based game
entitled “Catur Bistari" that is based on Islamic business approach.
Knowledge and skill of entrepreneurship and Islamic business
approach will be learned through the tasks that are incorporated
inside the game.
Abstract: The presence of cold air with the convergent
topography of the Lut valley over the valley-s sloping terrain can
generate Low Level Jets (LLJ). Moreover, the valley-parallel
pressure gradients and northerly LLJ are produced as a result of the
large-scale processes. In the numerical study the regional MM5
model was run leading to achieve an appropriate dynamical analysis
of flows in the region for summer and winter. The results of this
study show the presence of summer synoptical systems cause the
formation of north-south pressure gradients in the valley which could
be led to the blowing of winds with the velocity more than 14 ms-1
and vulnerable dust and wind storms lasting more than 120 days.
Whereas the presence of cold air masses in the region in winter,
cause the average speed of LLJs decrease. In this time downslope
flows are noticeable in creating the night LLJs.