Abstract: In wastewater treatment processes, aeration introduces
air into a liquid. In these systems, air is introduced by different
devices submerged in the wastewater. Smaller bubbles result in more
bubble surface area per unit of volume and higher oxygen transfer
efficiency. Jet pumps are devices that use air bubbles and are widely
used in wastewater treatment processes. The principle of jet pumps is
their ability to transfer energy of one fluid, called primary or motive,
into a secondary fluid or gas. These pumps have no moving parts and
are able to work in remote areas under extreme conditions. The
objective of this work is to study experimentally the characteristics of
the jet pump and the size of air bubbles in the laboratory water tank.
The effect of flow rate ratio on pump performance is investigated in
order to have a better understanding about pump behavior under
various conditions, in order to determine the efficiency of receiving
air bubbles different sizes. The experiments show that we should take
care when increasing the flow rate ratio while seeking to decrease
bubble size in the outlet flow. This study will help improve and
extend the use of the jet pump in many practical applications.
Abstract: Recently, there is a lot of interest in the field of under
water optical wireless communication for short range because of
its high bandwidth. But in most of the previous works line of
sight propagation or single scattering of photons only considered.
In practical case this is not applicable because of beam blockage in
underwater and multiple scattering also occurred during the photons
propagation through water. In this paper we consider a non-line
of sight underwater wireless optical communication system with
multiple scattering and examine the performance of the system using
monte carlo simulation. The distribution scattering angle of photons
are modeled by Henyey-Greenstein method. The average bit error
rate is calculated using on-off keying modulation for different water
types.
Abstract: Chrome tannery wastewater causes serious environmental hazard due to its high pollution potential. As a result, rigorous treatment is necessary for abatement of pollution from this type of wastewater. There are many research studies on chrome tannery wastewater treatment in the field of physical, chemical, and biological methods. In general, biological treatment process is found ineffective for direct application because of adverse effects by toxic chromium, sulphide, chloride etc. However, biological methods were employed mainly for a few sub processes generating significant amount of organic matter and without chromium, chlorides etc. In this context the present paper reviews the characteristics feature and pollution potential of wastewater generated from chrome tannery units and treatment of the same. The different biological processes used earlier and their chronological development for treatment of the chrome tannery wastewater are thoroughly reviewed in this paper. In this regard, the scope of hybrid bioreactor - an advanced technology option has also been explored, as this kind of treatment is well suited for the wastewater having inhibitory substances.
Abstract: In our research we aimed to test a managerial
approach for the fuzzy front end (FFE) of innovation by creating
controlled experiment/ business case in a breakthrough innovation
development. The experiment was in the sport industry and covered
all aspects of the customer discovery stage from ideation to
prototyping followed by patent application. In the paper we describe
and analyze mile stones, tasks, management challenges, decisions
made to create the break through innovation, evaluate overall
managerial efficiency that was at the considered FFE stage.
We set managerial outcome of the FFE stage as a valid product
concept in hand. In our paper we introduce hypothetical construct
“Q-factor” that helps us in the experiment to distinguish quality of
FFE outcomes.
The experiment simulated for entrepreneur the FFE of innovation
and put on his shoulders responsibility for the outcome of valid
product concept. While developing managerial approach to reach the
outcome there was a decision to look on product concept from the
cognitive psychology and cognitive science point of view. This view
helped us to develop the profile of a person whose projection (mental
representation) of a new product could optimize for a manager or
entrepreneur FFE activities. In the experiment this profile was tested
to develop breakthrough innovation for swimmers. Following the
managerial approach the product concept was created to help
swimmers to feel/sense water. The working prototype was developed
to estimate the product concept validity and value added effect for
customers.
Based on feedback from coachers and swimmers there were strong
positive effect that gave high value for customers, and for the
experiment – the valid product concept being developed by proposed
managerial approach for the FFE.
In conclusions there is a suggestion of managerial approach that
was derived from experiment.
Abstract: Activated carbon is an amorphous carbon chain which
has extremely extended surface area. High surface area of activated
carbon is due to the porous structure. Activated carbon, using a
variety of materials such as coal and cellulosic materials; can be
obtained by both physical and chemical methods. The prepared
activated carbon can be used for decolorize, deodorize and also can
be used for removal of organic and non-organic pollution. In this
study, pomegranate peel was subjected to 800W microwave power
for 1 to 4 minutes. Also fresh pomegranate peel was used for the
reference material. Then ZnCl2 was used for the chemical activation
purpose. After the activation process, activated pomegranate peels
were used for the adsorption of Zn metal (40 ppm) in the waste water.
As a result of the adsorption experiments, removal of heavy metals
ranged from 89% to 85%.
Abstract: The hydrodynamics and heat transfer characteristics
of a vaporized elongated bubble in a rectangular microchannel have
been simulated based on Cahn-Hilliard phase-field method. In the
simulations, the initially nucleated bubble starts growing as it comes
in contact with superheated water. The growing shape of the bubble
compared well with the available experimental data in the literature.
Abstract: The work allowed gaining knowledge about redox and
speciation changes of As, Cr and Sb ionic forms in Klodnica River
water. This kind of studies never has been conducted in this region of
Poland. In study optimized and validated previously HPLC-ICP-MS
methods for determination of As, Sb and Cr was used. Separation
step was done using high-performance liquid chromatograph
equipped with ion-exchange column followed by ICP-MS
spectrometer detector. Preliminary studies included determination of
the total concentration of As, Sb and Cr, pH, Eh, temperature and
conductivity of the water samples. The study was conducted monthly
from March to August 2014, at six points on the Klodnica River. The
results indicate that exceeded at acceptable concentration of total Cr
and Sb was observed in Klodnica River and we should qualify
Klodnica River waters below the second purity class. In Klodnica
River waters dominates oxidized antimony and arsenic forms, as well
as the two forms of chromium Cr(VI) and Cr(III). Studies have also
shown the methyl derivative of arsenic's presence.
Abstract: The formulated problem of optimization of the
technological process of water treatment for thermal power plants is
considered in this article. The problem is of multiparametric nature.
To optimize the process, namely, reduce the amount of waste water, a
new technology was developed to reuse such water. A mathematical
model of the technology of wastewater reuse was developed.
Optimization parameters were determined. The model consists of a
material balance equation, an equation describing the kinetics of ion
exchange for the non-equilibrium case and an equation for the ion
exchange isotherm. The material balance equation includes a
nonlinear term that depends on the kinetics of ion exchange. A direct
problem of calculating the impurity concentration at the outlet of the
water treatment plant was numerically solved. The direct problem
was approximated by an implicit point-to-point computation
difference scheme. The inverse problem was formulated as relates to
determination of the parameters of the mathematical model of the
water treatment plant operating in non-equilibrium conditions. The
formulated inverse problem was solved. Following the results of
calculation the time of start of the filter regeneration process was
determined, as well as the period of regeneration process and the
amount of regeneration and wash water. Multi-parameter
optimization of water treatment process for thermal power plants
allowed decreasing the amount of wastewater by 15%.
Abstract: Most people today are aware that global climate
change is not just a scientific theory but also a fact with worldwide
consequences. Global climate change is due to rapid urbanization,
industrialization, high population growth and current vulnerability of
the climatic condition. Water is becoming scarce as a result of global
climate change. To mitigate the problem arising due to global climate
change and its drought effect, harvesting rainwater from green roofs,
an environmentally-friendly and versatile technology, is becoming
one of the best assessment criteria and gaining attention in Malaysia.
This paper addresses the sustainability of green roofs and examines
the quality of water harvested from green roofs in comparison to
rainwater. The factors that affect the quality of such water, taking
into account, for example, roofing materials, climatic conditions, the
frequency of rainfall frequency and the first flush. A green roof was
installed on the Humid Tropic Centre (HTC) is a place of the study
on monitoring program for urban Stormwater Management Manual
for Malaysia (MSMA), Eco-Hydrological Project in Kuala Lumpur,
and the rainwater was harvested and evaluated on the basis of four
parameters i.e., conductivity, dissolved oxygen (DO), pH and
temperature. These parameters were found to fall between Class I and
Class III of the Interim National Water Quality Standards (INWQS)
and the Water Quality Index (WQI). Some preliminary treatment
such as disinfection and filtration could likely to improve the value of
these parameters to class I. This review paper clearly indicates that
there is a need for more research to address other microbiological and
chemical quality parameters to ensure that the harvested water is
suitable for use potable water for domestic purposes. The change in
all physical, chemical and microbiological parameters with respect to
storage time will be a major focus of future studies in this field.
Abstract: Hybrid bioreactor having both suspended-growth and
attached-growth bacteria is found a novel and excellent bioreactor
system for treating the municipal wastewater containing inhibitory
substrates too. In this reactor a fraction of substrate is used by
suspended biomass and the remaining by attached biomass resulting
in the competition between the two growths for the substrate. The
combination of suspended and attached growth provides the system
with enhanced biomass concentration and sludge age more than those
in ASP. Similar to attached growth system, the hybrid bioreactor
ensures considerable efficiency for treating toxic and refractory
substances in wastewater. For the process design of hybrid bioreactor
a suitable mathematical model is required. Although various
mathematical models were developed on hybrid bioreactor in due
course of time in earlier research works, none of them was found
having a specific simplified solution of the corresponding models and
without having any drawback. To overcome this drawback authors
already developed a simplified mathematical model for process
design of a hybrid bioreactor. The present paper briefly highlights on
the various aspects of process design of an aerobic hybrid bioreactor
for the treatment of municipal wastewater.
Abstract: Comparing other methods of waste water treatment,
constructed wetlands are one of the most fascinating practices
because being a natural process they are eco-friendly have low
construction and maintenance cost and have considerable capability
of wastewater treatment. The current research was focused mainly on
comparison of Ranunculus muricatus and Typha latifolia as wetland
plants for domestic wastewater treatment by designing and
constructing efficient pilot scale horizontal subsurface flow
mesocosms. Parameters like chemical oxygen demand, biological
oxygen demand, phosphates, sulphates, nitrites, nitrates, and
pathogenic indicator microbes were studied continuously with
successive treatments. Treatment efficiency of the system increases
with passage of time and with increase in temperature. Efficiency of
T. latifolia planted setups in open environment was fairly good for
parameters like COD and BOD5 which was showing reduction up to
82.5% for COD and 82.6% for BOD5 while DO was increased up to
125%. Efficiency of R. muricatus vegetated setup was also good but
lowers than that of T. latifolia planted showing 80.95% removal of
COD and BOD5. Ranunculus muricatus was found effective in
reducing bacterial count in wastewater. Both macrophytes were
found promising in wastewater treatment.
Abstract: Paints are the most widely used methods of protection
against atmospheric corrosion of metals. The aim of this work was to
determine the protective performance of epoxy coating against sea
water before and after damage.
Investigations are conducted using stationary and non-stationary
electrochemical tools such as electrochemical impedance
spectroscopy has allowed us to characterize the protective qualities of
these films. The application of the EIS on our damaged in-situ
painting shows the existence of several capacitive loops which is an
indicator of the failure of our tested paint. Microscopic analysis
(micrograph) helped bring essential elements in understanding the
degradation of our paint condition and immersion training corrosion
products.
Abstract: Surface modification and functionalization has been
an important tool for scientists in order to open new frontiers in
nanoscience and nanotechnology. Desired surface characteristics for
the intended applications can be achieved with surface
functionalization.
In this work, the effect of water soluble ligands on the adsorption
capabilities of silver nanoparticles onto AC which was synthesized
from German beech wood was investigated. Sodium borohydride
(NaBH4) and polyvinyl alcohol (PVA) were used as the ligands.
Silver nanoparticles with different surface coatings have average
sizes range from 10 to 13 nm. They were synthesized in aqueous
media by reducing Ag (I) ion in the presence of ligands. These
particles displayed adsorption tendencies towards AC when they
were mixed together and shaken in distilled water.
Silver nanoparticles (NaBH4-AgNPs) reduced and stabilized by
NaBH4 adsorbed onto AC with a homogenous dispersion of
aggregates with sizes in the range of 100-400 nm. Beside, silver
nanoparticles, which were prepared in the presence of both NaBH4
and PVA (NaBH4/PVA-Ag NPs), demonstrated that NaBH4/PVA-Ag
NPs adsorbed and dispersed homogenously but, they aggregated with
larger sizes on the AC surface (range from 300 to 600 nm). In
addition, desorption resistance of Ag nanoparticles were investigated
in distilled water. According to the results AgNPs were not desorbed
on the AC surface in distilled water.
Abstract: Water contamination by toxic compound is one of the serious environmental problems today. These toxic compounds mostly originated from industrial effluents, agriculture, natural sources and human waste. These studies focus on modification of multiwalled carbon nanotube (MWCNTs) with nanoparticle of calixarene and explore the possibility of using this modification for the remediation of cadmium in water. The nanocomposites were prepared by dissolving calixarene in chloroform solution as solvent, followed by additional multiwalled carbon nanotube (MWCNTs) then sonication process for 3 hour and fabricated the nanocomposites on substrate by spin coating method. Finally, the nanocomposites were tested on cadmium ion (10 mg/ml). The morphology of nanocomposites was investigated by FESEM showing the formation of calixarene on the outer walls of carbon nanotube and cadmium ion also clearly seen from the micrograph. This formation was supported by using energy dispersive x-ray (EDX). The presence of cadmium ions in the films, leads to some changes in the surface potential and Fourier Transform Infrared spectroscopy (FTIR).The nanocomposites MWCNTs-calixarene have potential for development of sensor for pollutant monitoring and nanoelectronics devices applications.
Abstract: The aim of this work was to apply extractive
distillation for acetonitrile removal from water solutions, to validate
thermodynamic criterion based on excess Gibbs energy to entrainer
selection process for acetonitrile – water mixture separation and show
its potential efficiency at isothermal conditions as well as at isobaric
(conditions of real distillation process), to simulate and analyze an
extractive distillation process with chosen entrainers: optimize
amount of trays and feeds, entrainer/original mixture and reflux
ratios. Equimolar composition of the feed stream was chosen for the
process, comparison of the energy consumptions was carried out.
Glycerol was suggested as the most energetically and ecologically
suitable entrainer.
Abstract: This study presents synthesis of novel block
copolymers of thienyl end capped ethoxylated nonyl phenol and
pyrrole via chemical oxidative polymerization. Ethoxylated nonyl
phenol (ENP) was reacted with 2-thiophenecarbonyl chloride in order
to synthesize a macromonomer containing thienyl end-group (ENPThC).
Then copolymers of ENP-ThC and pyrrole were synthesized
by chemical oxidative polymerization using iron (III) chloride as an
oxidant. ENP-ThC served both as a macromonomer and an emulsifier
for pyrrole with poor solubility in water.
The synthesized block copolymers (ENP-ThC-b-PPy) were
characterized by spectroscopic analysis and the electrical
conductivities were investigated with 4-point probe technique.
Abstract: The rate of natural gas dissociation from the Coal
Matrix depends on depressurization of reservoir through removing of
the cleat water from the coal seam. These waters are similar to brine
and aged of very long years. For improving the connectivity through
fracking /fracturing, high pressure liquids are pumped off inside the
coal body. A significant quantity of accumulated water, a combined
mixture of cleat water and fracking fluids (back flow water) is
pumped out through gas well. In Queensland, Australia Coal Seam
Gas (CSG) industry is in booming state and estimated of 30,000 wells
would be active for CSG production forecasting life span of 30 years.
Integrated water management along with water softening programs is
practiced for subsequent treatment and later on discharge to nearby
surface water catchment. Water treatment is an important part of the
CSG industry. A case study on a CSG site and review on the test
results are discussed for assessing the Standards & Practices for
management of CSG by-product water and their subsequent disposal
activities. This study was directed toward (i) water management and
softening process in Spring Gully CSG field, (ii) Comparative
analysis on experimental study and standards and (iii) Disposal of the
treated water. This study also aimed for alternative usages and their
impact on vegetation, living species as well as long term effects.
Abstract: The present study was carried out to evaluate the
effect of different levels of dietary seed and extract of Harmal
(Peganum harmala L.) on immunity of broiler chicks. A total of 350
one-day old broiler chicks (Ross 308) were randomly allocated to
five dietary treatments with four replicates pen of 14 birds each.
Dietary treatments consisted of control, 1 and 2 g/kg Harmal seed in
diet, 100 and 200 mg/L Harmal seed extract in water. Broilers
received dietary treatments from 1 to 42 d. Two birds from each pen
were randomly weighed and sacrificed at 42 d of age, the relative
weight of lymphoid organs (bursa of Fabercius and spleen) to live
weight were calculated. Antibody titers against Newcastle and
influenza viruses and sheep red blood cell were measured at 30 d of
age. Results showed that the relative weights of lymphoid organs
were not affected by dietary treatments. Furthermore, antibody titer
against Newcastle and influenza viruses as well as sheep red blood
cell antigen were significantly (P
Abstract: Replacement of plastics used in the food industry
seems to be a serious issue to overcome mainly the environmental
problems in recent years. This study investigates the hydrophilicity
and permeability properties of starch biopolymer which ethylene
vinyl alcohol (EVOH) (0-10%) and nanocrystalline cellulose (NCC)
(1-15%) were used to enhance its properties. Starch -EVOH
nanocomposites were prepared by casting method in different
formulations. NCC production by acid hydrolysis was confirmed by
scanning electron microscopy. Solubility, water vapor permeability,
water vapor transmission rate and moisture absorbance were
measured on each of the nanocomposites. The results were analyzed
by SAS software. The lowest moisture absorbance was measured in
pure starch nanocomposite containing 8% NCC. The lowest
permeability to water vapor belongs to starch nanocomposite
containing 8% NCC and the sample containing 7.8% EVOH and 13%
NCC. Also the lowest solubility was observed in the composite
contains the highest amount of EVOH. Applied Process resulted in
production of bio films which have good resistance to water vapor
permeability and solubility in water. The use of NCC and EVOH
leads to reduced moisture absorbance property of the biofilms.
Abstract: Wet scrubbers have found widespread use in cleaning
contaminated gas streams because of their ability to remove
particulates and based on the applications of scrubbing of marine
engine exhaust gases by spraying sea-water. In order to examine the
flow characteristics inside the scrubber, the model is designated with
flow properties of hot air and water sprayer. The flow dynamics of
evaporation of hot air by the injection of water droplets is the key
factor considered in this paper. The flow behavior inside the scrubber
was investigated from the previous works and to sum up the
evaporation rate with respect to the concentration of water droplets are
predicted to bring out the competent modelling. The numerical
analysis using CFD facilitates in understanding the problem better and
empathies the behavior of the model over its entire operating envelope.