Abstract: In this study, WC-Ni-based cemented carbides having different nickel contents were used as the substrate for cutting tool materials. Hardened steel was turned by a (Ti,W,Si)N-coated WC-Ni-based cemented carbide tool, and the tool wear was experimentally investigated. The following results were obtained: (1) In the (Ti,W,Si)N-coated WC-Ni-based cemented carbide, the hardness of the coating film was not much different from the content of the binding material, Ni, and the adhesion strength increased with a decrease in Ni content. (2) There is little difference between the wear progress of the (Ti,W,Si)N-coated WC-7%Ni-based cemented carbide tool and that of the (Ti,W,Si)N-coated WC-6%Co-based cemented carbide tool. (3) The wear progress of the (Ti,W,Si)N-coated WC-Ni-based cemented carbide became slower with a decrease in Ni content.
From the above, it is has become clear that WC-Ni-based cemented carbide can be used as a substrate for cutting tool materials.
Abstract: The article deals with the possibilities of increasing the efficiency of turning thin-walled workpieces. It proposes a new strategy for turning and it proposes new implementation of roughing cycles where a variable depth of cut is applied. Proposed roughing cycles are created in the CAD/CAM system. These roughing cycles are described in relation to their further use in practice.
The experimental research has focused on monitoring the durability of cutting tool and increases its tool life. It compares the turning where the standard roughing cycle is used and the turning where the proposed roughing cycle with variable depth of cut is applied. In article are monitored tool wear during cutting with the sintered carbide cutting edge. The result verifies theoretical prerequisites of tool wear.
Abstract: This study presents a new method for detecting the
cutting tool wear based on the measured cutting force signals using
the regression model and I-kaz method. The detection of tool wear
was done automatically using the in-house developed regression
model and 3D graphic presentation of I-kaz 3D coefficient during
machining process. The machining tests were carried out on a CNC
turning machine Colchester Master Tornado T4 in dry cutting
condition, and Kistler 9255B dynamometer was used to measure the
cutting force signals, which then stored and displayed in the DasyLab
software. The progression of the cutting tool flank wear land (VB)
was indicated by the amount of the cutting force generated. Later, the
I-kaz was used to analyze all the cutting force signals from beginning
of the cut until the rejection stage of the cutting tool. Results of the IKaz
analysis were represented by various characteristic of I-kaz 3D
coefficient and 3D graphic presentation. The I-kaz 3D coefficient
number decreases when the tool wear increases. This method can be
used for real time tool wear monitoring.
Abstract: In the present paper, the three-dimensional
temperature field of tool is determined during the machining and
compared with experimental work on C45 workpiece using carbide
cutting tool inserts. During the metal cutting operations, high
temperature is generated in the tool cutting edge which influence on
the rate of tool wear. Temperature is most important characteristic of
machining processes; since many parameters such as cutting speed,
surface quality and cutting forces depend on the temperature and high
temperatures can cause high mechanical stresses which lead to early
tool wear and reduce tool life. Therefore, considerable attention is
paid to determine tool temperatures. The experiments are carried out
for dry and orthogonal machining condition. The results show that
the increase of tool temperature depends on depth of cut and
especially cutting speed in high range of cutting conditions.
Abstract: Ultrasonic machining (USM) is a non-traditional
machining process being widely used for commercial machining of
brittle and fragile materials such as glass, ceramics and
semiconductor materials. However, USM could be a viable
alternative for machining a tough material such as titanium; and this
aspect needs to be explored through experimental research. This
investigation is focused on exploring the use of ultrasonic machining
for commercial machining of pure titanium (ASTM Grade-I) and
evaluation of tool wear rate (TWR) under controlled experimental
conditions. The optimal settings of parameters are determined
through experiments planned, conducted and analyzed using Taguchi
method. In all, the paper focuses on parametric optimization of
ultrasonic machining of pure titanium metal with TWR as response,
and validation of the optimized value of TWR by conducting
confirmatory experiments.
Abstract: In metal cutting industries, mathematical/statistical
models are typically used to predict tool replacement time. These
off-line methods usually result in less than optimum replacement
time thereby either wasting resources or causing quality problems.
The few online real-time methods proposed use indirect measurement
techniques and are prone to similar errors. Our idea is based on
identifying the optimal replacement time using an electronic nose to
detect the airborne compounds released when the tool wear reaches
to a chemical substrate doped into tool material during the
fabrication. The study investigates the feasibility of the idea, possible
doping materials and methods along with data stream mining
techniques for detection and monitoring different phases of tool
wear.
Abstract: Considering complexity of products, new geometrical
design and investment tolerances that are necessary, measuring and
dimensional controlling involve modern and more precise methods.
Photo digitizing method using two cameras to record pictures and
utilization of conventional method named “cloud points" and data
analysis by the use of ATOUS software, is known as modern and
efficient in mentioned context. In this paper, benefits of photo
digitizing method in evaluating sampling of machining processes
have been put forward. For example, assessment of geometrical
integrity surface in 5-axis milling process and measurement of
carbide tool wear in turning process, can be can be brought forward.
Advantages of this method comparing to conventional methods have
been expressed.
Abstract: FW4 is a newly developed hot die material widely
used in Forging Dies manufacturing. The right selection of the
machining conditions is one of the most important aspects to take
into consideration in the Electrical Discharge Machining (EDM) of
FW4. In this paper an attempt has been made to develop
mathematical models for relating the Material Removal Rate (MRR),
Tool Wear Ratio (TWR) and surface roughness (Ra) to machining
parameters (current, pulse-on time and voltage). Furthermore, a study
was carried out to analyze the effects of machining parameters in
respect of listed technological characteristics. The results of analysis
of variance (ANOVA) indicate that the proposed mathematical
models, can adequately describe the performance within the limits of
the factors being studied.
Abstract: Electro Chemical Discharge Machining (ECDM) is an
emerging hybrid machining process used in precision machining of hard and brittle non-conducting materials. The present paper gives a
critical review on materials machined by ECDM under the prevailing machining conditions; capability indicators of the process are
reported. Some results obtained while performing experiments in micro-channeling on soda lime glass using ECDM are also presented. In these experiments, Tool Wear (TW) and Material Removal (MR)
were studied using design of experiments and L–4 orthogonal array. Experimental results showed that the applied voltage was the most influencing parameter in both MR and TW studies. Field
emission scanning electron microscopy (FESEM) results obtained on the microchannels confirmed the presence of micro-cracks, primarily responsible for MR. Chemical etching was also seen along the edges.
The Energy dispersive spectroscopy (EDS) results were used to detect the elements present in the debris and specimens.
Abstract: Twist drills are geometrical complex tools and thus various researchers have adopted different mathematical and experimental approaches for their simulation. The present paper acknowledges the increasing use of modern CAD systems and using the API (Application Programming Interface) of a CAD system, drilling simulations are carried out. The developed DRILL3D software routine, creates parametrically controlled tool geometries and using different cutting conditions, achieves the generation of solid models for all the relevant data involved (drilling tool, cut workpiece, undeformed chip). The final data derived, consist a platform for further direct simulations regarding the determination of cutting forces, tool wear, drilling optimizations etc.
Abstract: Electrical Discharge Machine (EDM) is especially
used for the manufacturing of 3-D complex geometry and hard
material parts that are extremely difficult-to-machine by conventional
machining processes. In this paper authors review the research work
carried out in the development of die-sinking EDM within the past
decades for the improvement of machining characteristics such as
Material Removal Rate, Surface Roughness and Tool Wear Ratio. In
this review various techniques reported by EDM researchers for
improving the machining characteristics have been categorized as
process parameters optimization, multi spark technique, powder
mixed EDM, servo control system and pulse discriminating. At the
end, flexible machine controller is suggested for Die Sinking EDM to
enhance the machining characteristics and to achieve high-level
automation. Thus, die sinking EDM can be integrated with Computer
Integrated Manufacturing environment as a need of agile
manufacturing systems.
Abstract: The quality of a machined surface is becoming more and more important to justify the increasing demands of sophisticated component performance, longevity, and reliability. Usually, any machining operation leaves its own characteristic evidence on the machined surface in the form of finely spaced micro irregularities (surface roughness) left by the associated indeterministic characteristics of the different elements of the system: tool-machineworkpart- cutting parameters. However, one of the most influential sources in machining affecting surface roughness is the instantaneous state of tool edge. The main objective of the current work is to relate the in-process immeasurable cutting edge deformation and surface roughness to a more reliable easy-to-measure force signals using a robust non-linear time-dependent modeling regression techniques. Time-dependent modeling is beneficial when modern machining systems, such as adaptive control techniques are considered, where the state of the machined surface and the health of the cutting edge are monitored, assessed and controlled online using realtime information provided by the variability encountered in the measured force signals. Correlation between wear propagation and roughness variation is developed throughout the different edge lifetimes. The surface roughness is further evaluated in the light of the variation in both the static and the dynamic force signals. Consistent correlation is found between surface roughness variation and tool wear progress within its initial and constant regions. At the first few seconds of cutting, expected and well known trend of the effect of the cutting parameters is observed. Surface roughness is positively influenced by the level of the feed rate and negatively by the cutting speed. As cutting continues, roughness is affected, to different extents, by the rather localized wear modes either on the tool nose or on its flank areas. Moreover, it seems that roughness varies as wear attitude transfers from one mode to another and, in general, it is shown that it is improved as wear increases but with possible corresponding workpart dimensional inaccuracy. The dynamic force signals are found reasonably sensitive to simulate either the progressive or the random modes of tool edge deformation. While the frictional force components, feeding and radial, are found informative regarding progressive wear modes, the vertical (power) components is found more representative carrier to system instability resulting from the edge-s random deformation.
Abstract: Titanium alloys like the modern alloy Ti 6Al 2Sn 4Zr 6Mo (Ti-6246) combine excellent specific mechanical properties and corrosion resistance. On the other hand,due to their material characteristics, machining of these alloys is difficult to perform. The aim of the current study is the analyses of wear mechanisms of coated cemented carbide tools applied in orthogonal cutting experiments of Ti-6246 alloy. Round bars were machined with standard coated tools in dry conditions on a CNC latheusing a wide range of cutting speeds and cutting depths. Tool wear mechanisms were afterwards investigated by means of stereo microscopy, optical microscopy, confocal microscopy and scanning electron microscopy. Wear mechanisms included fracture of the tool tip (total failure) and abrasion. Specific wear features like crater wear, micro cracks and built-up edgeformation appeared depending of the mechanical and thermal conditions generated in the workpiece surface by the cutting action.
Abstract: Tool wear and surface roughness prediction plays a
significant role in machining industry for proper planning and control
of machining parameters and optimization of cutting conditions. This
paper deals with developing an artificial neural network (ANN)
model as a function of cutting parameters in turning steel under
minimum quantity lubrication (MQL). A feed-forward
backpropagation network with twenty five hidden neurons has been
selected as the optimum network. The co-efficient of determination
(R2) between model predictions and experimental values are 0.9915,
0.9906, 0.9761 and 0.9627 in terms of VB, VM, VS and Ra
respectively. The results imply that the model can be used easily to
forecast tool wear and surface roughness in response to cutting
parameters.
Abstract: Coated tool inserts can be considered as the backbone
of machining processes due to their wear and heat resistance.
However, defects of coating can degrade the integrity of these inserts
and the number of these defects should be minimized or eliminated if
possible. Recently, the advancement of coating processes and
analytical tools open a new era for optimizing the coating tools.
First, an overview is given regarding coating technology for cutting
tool inserts. Testing techniques for coating layers properties, as well
as the various coating defects and their assessment are also surveyed.
Second, it is introduced an experimental approach to examine the
possible coating defects and flaws of worn multicoated carbide
inserts using two important techniques namely scanning electron
microscopy and atomic force microscopy. Finally, it is
recommended a simple procedure for investigating manufacturing
defects and flaws of worn inserts.
Abstract: The paper is dealing by testing of ceramic cutting
tools with an interrupted machining. Tests will be provided on fixture
– interrupted cut simulator. This simulator has 4 mouldings on
circumference and cutting edge is put a shocks during 1 revolution.
Criteria of tool wear are destruction of cutting tool or 6000 shocks.
Like testing cutting tool material will be products of Sandvik
Coromant 6190, 620, 650 and 670. Machined materials was be steels
15 128 (13MoCrV6). Cutting speed (408 m.min-1 and 580 m.min-1)
and cutting feed (0,15 mm; 0,2 mm; 0,25 mm and 0,3 mm) were
variable parameters and cutting depth was constant parameter.
Abstract: Development of artificial neural network (ANN) for
prediction of aluminum workpieces' surface roughness in ultrasonicvibration
assisted turning (UAT) has been the subject of the present
study. Tool wear as the main cause of surface roughness was also
investigated. ANN was trained through experimental data obtained
on the basis of full factorial design of experiments. Various
influential machining parameters were taken into consideration. It
was illustrated that a multilayer perceptron neural network could
efficiently model the surface roughness as the response of the
network, with an error less than ten percent. The performance of the
trained network was verified by further experiments. The results of
UAT were compared with the results of conventional turning
experiments carried out with similar machining parameters except for
the vibration amplitude whence considerable reduction was observed
in the built-up edge and the surface roughness.
Abstract: In the present work, a study has been made on the combination of the electrical discharge machining (EDM) with ultrasonic vibrations to improve the machining efficiency. In experiments the graphite used as tool electrode and material of workpiece was AISIH13 tool steel. The parameters such as discharge peak current and pulse duration were changed to explore their effect on the material removal rate (MRR), relative tool wear ratio (TWR) and surface roughness. From the experimental result it can be seen that ultrasonic vibration of the workpiece can significantly reduces the inactive pulses and improves the stability of process. It was found that ultrasonic assisted EDM (US-EDM) is effective in attaining a high material removal rate (MRR) in finishing regime.
Abstract: In turning hardened steel, polycrystalline cubic boron
nitride (cBN) compacts are widely used, due to their higher hardness
and higher thermal conductivity. However, in milling hardened steel,
fracture of cBN cutting tools readily occurs because they have poor
fracture toughness. Therefore, coated cemented carbide tools, which
have good fracture toughness and wear resistance, are generally
widely used. In this study, hardened steel (ASTM D2, JIS SKD11,
60HRC) was milled with three physical vapor deposition
(PVD)-coated cemented carbide end mill cutters in order to determine
effective tool materials for cutting hardened steel at high cutting
speeds. The coating films used were (Ti,W)N/(Ti,W,Si)N and
(Ti,W)N/(Ti,W,Si,Al)N coating films. (Ti,W,Si,Al)N is a new type of
coating film. The inner layer of the (Ti,W)N/(Ti,W,Si)N and
(Ti,W)N/(Ti,W,Si,Al)N coating system is (Ti,W)N coating film, and
the outer layer is (Ti,W,Si)N and (Ti,W,Si,Al)N coating films,
respectively. Furthermore, commercial (Ti,Al)N-based coating film
was also used. The following results were obtained: (1) In milling
hardened steel at a cutting speed of 3.33 m/s, the tool wear width of the
(Ti,W)N/(Ti,W,Si,Al)N-coated tool was smaller than that of the
(Ti,W)N/(Ti,W,Si)N-coated tool. And, compared with the commercial
(Ti,Al)N, the tool wear width of the (Ti,W)N/(Ti,W,Si,Al)N-coated
tool was smaller than that of the (Ti,Al)N-coated tool. (2) The tool
wear of the (Ti,W)N/(Ti,W,Si,Al)N-coated tool increased with an
increase in cutting speed. (3) The (Ti,W)N/(Ti,W,Si,Al)N-coated
cemented carbide was an effective tool material for high-speed cutting
below a cutting speed of 3.33 m/s.
Abstract: The stochastic nature of tool life using conventional discrete-wear data from experimental tests usually exists due to many individual and interacting parameters. It is a common practice in batch production to continually use the same tool to machine different parts, using disparate machining parameters. In such an environment, the optimal points at which tools have to be changed, while achieving minimum production cost and maximum production rate within the surface roughness specifications, have not been adequately studied. In the current study, two relevant aspects are investigated using coated and uncoated inserts in turning operations: (i) the accuracy of using machinability information, from fixed parameters testing procedures, when variable parameters situations are emerged, and (ii) the credibility of tool life machinability data from prior discrete testing procedures in a non-stop machining. A novel technique is proposed and verified to normalize the conventional fixed parameters machinability data to suit the cases when parameters have to be changed for the same tool. Also, an experimental investigation has been established to evaluate the error in the tool life assessment when machinability from discrete testing procedures is employed in uninterrupted practical machining.