Abstract: The concerns about clean environment and high oil
prices driving forces for the research on alternative fuels. The
research efforts directed towards improving the performance of C.I
engines using vegetable oil as fuel. The paper deals results of
performance of a four stroke, single cylinder C.I. engine by preheated
neat Karanja oil is done from 30
o
C to 100
o
C. The performance of the
engine was studied for a speed range between 1500 to 4000 rpm, with
the engine operated under full load conditions. The performance
parameters considered for comparing are brake specific fuel
consumption, thermal efficiency, brake power, Nox emission of the
engine. The engine offers lower thermal efficiency when it is
powered by preheated neat Karanja oil at higher speed. The power
developed and Nox emission increase with the increase in the fuel
inlet temperature and the specific fuel consumption is higher than
diesel fuel operation at all elevated fuel inlet temperature.
Abstract: Regenerative gas turbine engine cycle is presented that yields higher cycle efficiencies than simple cycle operating under the same conditions. The power output, efficiency and specific fuel consumption are simulated with respect to operating conditions. The analytical formulae about the relation to determine the thermal efficiency are derived taking into account the effected operation conditions (ambient temperature, compression ratio, regenerator effectiveness, compressor efficiency, turbine efficiency and turbine inlet temperature). Model calculations for a wide range of parameters are presented, as are comparisons with simple gas turbine cycle. The power output and thermal efficiency are found to be increasing with the regenerative effectiveness, and the compressor and turbine efficiencies. The efficiency increased with increase the compression ratio to 5, then efficiency decreased with increased compression ratio, but in simple cycle the thermal efficiency always increase with increased in compression ratio. The increased in ambient temperature caused decreased thermal efficiency, but the increased in turbine inlet temperature increase thermal efficiency.
Abstract: Combustion, emission and performance
characterization of a single cylinder diesel engine using methanol
diesel blends was carried out. The blends were 5% (v/v) methanol in
diesel (MD05) and 10% (v/v) methanol in diesel (MD10). The
problem of solubility of methanol and diesel was addressed by an
agitator placed inside the fuel tank to prevent phase separation. The
results indicated that total combustion duration was reduced by15.8%
for MD05 and 31.27% for MD10compared to the baseline data.
Ignition delay was increased with increasing methanol volume
fraction in the test fuel. Total cyclic heat release was reduced by
1.5% for MD05 and 6.7% for MD10 as compared to diesel baseline.
Emissions of carbon monoxide, hydrocarbons along with smoke were
reduced and that of nitrogen oxides were increased with rising
methanol contents in the test fuel. Full load brake thermal efficiency
was marginally reduced with increased methanol composition in the
blend.
Abstract: In countries with hot climates, air-conditioning forms
a large proportion of annual peak electrical demand, requiring
expansion of power plants to meet the peak demand, which goes
unused most of the time. Use of well-designed cool storage can offset
the peak demand to a large extent. In this study, an air conditioning
system with naturally stratified storage tank was designed,
constructed and tested. A new type of diffuser was designed and used
in this study. Factors that influence the performance of chilled water
storage tanks were investigated. The results indicated that stratified
storage tank consistently stratified well without any physical barrier.
Investigation also showed that storage efficiency decreased with
increasing flow rate due to increased mixing of warm and chilled
water. Diffuser design and layout primarily affected the mixing near
the inlet diffuser and the extent of this mixing had primary influence
on the shape of the thermocline. The heat conduction through tank
walls and through the thermocline caused widening of mixed volume.
Thermal efficiency of stratified storage tanks was as high as 90
percent, which indicates that stratified tanks can effectively be used
as a load management technique.
Abstract: In a bid to improve turbine entry temperature for maximizing the thermal efficiency of the HP stage gas turbine blade, an attempt is made in this paper to compare the performance of helicoidal ducted blade cooling with turbulator of different geometric proportion. It is found from analysis that there is significant improvement in cooling characteristics for turbine blade with turbulator geometry having larger e/D ratio. Also it is found from analysis, performance is vastly improved for greater thickness of turbulator geometry.
Abstract: This study presents the improvement of thermal
performance of heat pipe using copper nanofluid with aqueous
solution of n-Butanol. The nanofluids kept in the suspension of
conventional fluids have the potential of superior heat transfer
capability than the conventional fluids due to their improved thermal
conductivity. In this work, the copper nanofluid which has a 40 nm
size with a concentration of 100 mg/lit is kept in the suspension of
the de-ionized (DI) water and an aqueous solution of n-Butanol and
these fluids are used as a working medium in the heat pipe. The study
discusses about the effect of heat pipe inclination, type of working
fluid and heat input on the thermal efficiency and thermal resistance.
The experimental results are evaluated in terms of its performance
metrics and are compared with that of DI water.
Abstract: Turbine blade cooling is considered as the most
effective way of maintaining high operating temperature making use
of the available materials, and turbine systems with wet compression
have a potential for future power generation because of high efficiency
and high specific power with a relatively low cost. In this paper
performance analysis of wet-compression gas turbine cycle with
turbine blade cooling is carried out. The wet compression process is
analytically modeled based on non-equilibrium droplet evaporation.
Special attention is paid for the effects of pressure ratio and water
injection ratio on the important system variables such as ratio of
coolant fluid flow, fuel consumption, thermal efficiency and specific
power. Parametric studies show that wet compression leads to
insignificant improvement in thermal efficiency but significant
enhancement of specific power in gas turbine systems with turbine
blade cooling.
Abstract: Experiments were carried out to evaluate the
influence of the addition of hydrogen to the inlet air on the
performance of a single cylinder direct injection diesel engine.
Hydrogen was injected in the inlet manifold. The addition of
hydrogen was done on energy replacement basis. It was found that
the addition of hydrogen improves the combustion process due to
superior combustion characteristics of hydrogen in comparison to
conventional diesel fuels. It was also found that 10% energy
replacement improves the engine thermal efficiency by about 40%
and reduces the sfc by about 35% however the volumetric efficiency
was reduced by about 35%.
Abstract: Solid oxide fuel cells have been considered in the last years as one of the most promising technologies for very highefficiency electric energy generation from hydrogen or other hydrocarbons, both with simple fuel cell plants and with integrated gas turbine-fuel cell systems. In the present study, a detailed thermodynamic analysis has been carried out. Mass and exergy balances are performed not only for the whole plant but also for each component in order to evaluate the thermal efficiency of combined cycle. Moreover, different sources of irreversibilities within the SOFC stack have been discussed and a parametric study conducted to evaluate the effect of temperature as well as pressure on SOFC irreversibilities and its performance. In this investigation methane and hydrogen have been used for fueling the SOFC stack and combustion chamber.
Abstract: The counter flow solar air heaters, with four
transverse fins and wire mesh layers are constructed and investigated
experimentally for thermal efficiency at a geographic location of
Cyprus in the city of Famagusta. The absorber plate is replaced by
sixteen steel wire mesh layers, 0.18 x 0.18cm in cross section
opening and a 0.02cm in diameter. The wire mesh layers arranged in
three groups, first and second include 6 layers, while the third include
4 layers. All layers fixed in the duct parallel to the glazing and each
group separated from the others by wood frame thickness of 0.5cm to
reduce the pressure drop. The transverse fins arranged in a way to
force the air to flow through the bed like eight letter path with flow
depth 3cm. The proposed design has increased the heat transfer rate,
but on other hand causes a high pressure drop. The obtained results
show that, for air mass flow rate range between 0.011-0.036kg/s, the
thermal efficiency increases with increasing the air mass flow. The
maximum efficiency obtained is 65.6% for the mass flow rate of
0.036kg/s. Moreover, the temperature difference between the outlet
flow and the ambient temperature, ΔT, reduces as the air mass flow
rate increase. The maximum difference between the outlet and
ambient temperature obtained was 43°C for double pass for minimum
mass flow rate of 0.011kg/s. Comparison with a conventional solar
air heater collector shows a significantly development in the thermal
efficiency.
Abstract: The greenhouse effect and limitations on carbon
dioxide emissions concern engine maker and the future of the
internal combustion engines should go toward substantially and
improved thermal efficiency engine. Homogeneous charge
compression ignition (HCCI) is an alternative high-efficiency
technology for combustion engines to reduce exhaust emissions and
fuel consumption. However, there are still tough challenges in the
successful operation of HCCI engines, such as controlling the
combustion phasing, extending the operating range, and high
unburned hydrocarbon and CO emissions. HCCI and the exploitation
of ethanol as an alternative fuel is one way to explore new frontiers
of internal combustion engines with an eye towards maintaining its
sustainability. This study was done to extend database knowledge
about HCCI with ethanol a fuel.
Abstract: This paper presents the experimental results of a
single cylinder Enfield engine using an electronically controlled fuel
injection system which was developed to carry out exhaustive tests
using neat CNG, and mixtures of hydrogen in compressed natural gas
(HCNG) as 0, 5, 10, 15 and 20% by energy. Experiments were
performed at 2000 and 2400 rpm with wide open throttle and varying
the equivalence ratio. Hydrogen which has fast burning rate, when
added to compressed natural gas, enhances its flame propagation rate.
The emissions of HC, CO, decreased with increasing percentage of
hydrogen but NOx was found to increase. The results indicated a
marked improvement in the brake thermal efficiency with the
increase in percentage of hydrogen added. The improved thermal
efficiency was clearly observed to be more in lean region as
compared to rich region. This study is expected to reduce vehicular
emissions along with increase in thermal efficiency and thus help in
reduction of further environmental degradation.
Abstract: PCCI engines can reduce NOx and PM emissions
simultaneously without sacrificing thermal efficiency, but a low
combustion temperature resulting from early fuel injection, and
ignition occurring prior to TDC, can cause higher THC and CO
emissions and fuel consumption. In conclusion, it was found that the
PCCI combustion achieved by the 2-stage injection strategy with
optimized calibration factors (e.g. EGR rate, injection pressure, swirl
ratio, intake pressure, injection timing) can reduce NOx and PM
emissions simultaneously. This research works are expected to
provide valuable information conducive to a development of an
innovative combustion engine that can fulfill upcoming stringent
emission standards.
Abstract: In a travelling wave thermoacoustic device, the
regenerator sandwiched between a pair of (hot and cold) heat
exchangers constitutes the so-called thermoacoustic core, where the
thermoacoustic energy conversion from heat to acoustic power takes
place. The temperature gradient along the regenerator caused by the
two heat exchangers excites and maintains the acoustic wave in the
resonator. The devices are called travelling wave thermoacoustic
systems because the phase angle difference between the pressure and
velocity oscillation is close to zero in the regenerator. This paper
presents the construction and testing of a thermoacoustic engine
equipped with a ceramic regenerator, made from a ceramic material
that is usually used as catalyst substrate in vehicles- exhaust systems,
with fine square channels (900 cells per square inch). The testing
includes the onset temperature difference (minimum temperature
difference required to start the acoustic oscillation in an engine), the
acoustic power output, thermal efficiency and the temperature profile
along the regenerator.
Abstract: This paper describes the experimental efficiency of a
compact organic Rankine cycle (ORC) system with a compact
rotary-vane-type expander. The compact ORC system can be used for
power generation from low-temperature heat sources such as waste
heat from various small-scale heat engines, fuel cells, electric devices,
and solar thermal energy. The purpose of this study is to develop an
ORC system with a low power output of less than 1 kW with a hot
temperature source ranging from 60°C to 100°C and a cold
temperature source ranging from 10°C to 30°C. The power output of
the system is rather less due to limited heat efficiency. Therefore, the
system should have an economically optimal efficiency. In order to
realize such a system, an efficient and low-cost expander is
indispensable. An experimental ORC system was developed using the
rotary-vane-type expander which is one of possible candidates of the
expander. The experimental results revealed the expander
performance for various rotation speeds, expander efficiencies, and
thermal efficiencies. Approximately 30 W of expander power output
with 48% expander efficiency and 4% thermal efficiency with a
temperature difference between the hot and cold sources of 80°C was
achieved.
Abstract: Because of importance of energy, optimization of
power generation systems is necessary. Gas turbine cycles are
suitable manner for fast power generation, but their efficiency is
partly low. In order to achieving higher efficiencies, some
propositions are preferred such as recovery of heat from exhaust
gases in a regenerator, utilization of intercooler in a multistage
compressor, steam injection to combustion chamber and etc.
However thermodynamic optimization of gas turbine cycle, even
with above components, is necessary. In this article multi-objective
genetic algorithms are employed for Pareto approach optimization of
Regenerative-Intercooling-Gas Turbine (RIGT) cycle. In the multiobjective
optimization a number of conflicting objective functions
are to be optimized simultaneously. The important objective
functions that have been considered for optimization are entropy
generation of RIGT cycle (Ns) derives using Exergy Analysis and
Gouy-Stodola theorem, thermal efficiency and the net output power
of RIGT Cycle. These objectives are usually conflicting with each
other. The design variables consist of thermodynamic parameters
such as compressor pressure ratio (Rp), excess air in combustion
(EA), turbine inlet temperature (TIT) and inlet air temperature (T0).
At the first stage single objective optimization has been investigated
and the method of Non-dominated Sorting Genetic Algorithm
(NSGA-II) has been used for multi-objective optimization.
Optimization procedures are performed for two and three objective
functions and the results are compared for RIGT Cycle. In order to
investigate the optimal thermodynamic behavior of two objectives,
different set, each including two objectives of output parameters, are
considered individually. For each set Pareto front are depicted. The
sets of selected decision variables based on this Pareto front, will
cause the best possible combination of corresponding objective
functions. There is no superiority for the points on the Pareto front
figure, but they are superior to any other point. In the case of three
objective optimization the results are given in tables.
Abstract: Transesterified vegetable oils (biodiesel) are promising alternative fuel for diesel engines. Used vegetable oils are disposed from restaurants in large quantities. But higher viscosity restricts their direct use in diesel engines. In this study, used cooking oil was dehydrated and then transesterified using an alkaline catalyst. The combustion, performance and emission characteristics of Used Cooking oil Methyl Ester (UCME) and its blends with diesel oil are analysed in a direct injection C.I. engine. The fuel properties and the combustion characteristics of UCME are found to be similar to those of diesel. A minor decrease in thermal efficiency with significant improvement in reduction of particulates, carbon monoxide and unburnt hydrocarbons is observed compared to diesel. The use of transesterified used cooking oil and its blends as fuel for diesel engines will reduce dependence on fossil fuels and also decrease considerably the environmental pollution.
Abstract: This presentation reviews recent advances in superalloys and thermal barrier coating (TBC) for application in hot sections of energy-efficient gas-turbine engines. It has been reviewed that in the modern combined-cycle gas turbines (CCGT) applying single-crystal energy materials (SC superalloys) and thermal barrier coatings (TBC), and – in one design – closed-loop steam cooling, thermal efficiency can reach more than 60%. These technological advancements contribute to profitable and clean power generation with reduced emission. Alternatively, the use of advanced superalloys (e.g. GTD-111 superalloy, Allvac 718Plus superalloy) and advanced thermal barrier coatings (TBC) in modern gas-turbines has been shown to yield higher energy-efficiency in power generation.
Abstract: The increased number of automobiles in recent years
has resulted in great demand for fossil fuel. This has led to the
development of automobile by using alternative fuels which include
gaseous fuels, biofuels and vegetables oils as fuel. Energy from
biomass and more specific bio-diesel is one of the opportunities that
could cover the future demand of fossil fuel shortage. Biomass in the
form of cashew nut shell represents a new energy source and
abundant source of energy in India. The bio-fuel is derived from
cashew nut shell oil and its blend with diesel are promising
alternative fuel for diesel engine. In this work the pyrolysis Cashew
Nut Shell Liquid (CNSL)-Diesel Blends (CDB) was used to run the
Direct Injection (DI) diesel engine. The experiments were conducted
with various blends of CNSL and Diesel namely B20, B40, B60, B80
and B100. The results are compared with neat diesel operation. The
brake thermal efficiency was decreased for blends of CNSL and
Diesel except the lower blends of B20. The brake thermal efficiency
of B20 is nearly closer to that of diesel fuel. Also the emission level
of the all CNSL and Diesel blends was increased compared to neat
diesel. The higher viscosity and lower volatility of CNSL leads to
poor mixture formation and hence lower brake thermal efficiency and
higher emission levels. The higher emission level can be reduced by
adding suitable additives and oxygenates with CNSL and Diesel
blends.
Abstract: The present study conducted experimental investigation on combustion and emission characteristics of compression ignition engine using diesel as pilot fuel and methane, hydrogen and methane/hydrogen mixture as gaseous fuels at 1800 rev min-1. The effect of gaseous fuel on peak cylinder pressure and heat release is modest at low to medium loads. At high load, the high combustion temperature and high quantity of pilot fuel contribute to better combustion efficiency for all kinds of gaseous fuels and increases the peak cylinder pressure. Enrichment of hydrogen in methane gradually increases the peak cylinder pressure. The brake thermal efficiency increases with higher hydrogen fraction at lower loads. Hydrogen addition in methane contributed to a proportional reduction of CO/CO2/HC emission without penalty of NOx. For particulate emission, methane and hydrogen, could both suppress the particle emission. 30% hydrogen fraction in methane is observed to be best in reducing the particulate emission.