Abstract: Permanent rivers are the main sources of renewable
water supply for the croplands under the irrigation and drainage
schemes. They are also the major source of sediment loads transport
into the storage reservoirs of the hydro-electrical dams, diversion
weirs and regulating dams. Sedimentation process results from soil
erosion which is related to poor watershed management and human
intervention ion in the hydraulic regime of the rivers. These could
change the hydraulic behavior and as such, leads to riverbed and river
bank scouring, the consequences of which would be sediment load
transport into the dams and therefore reducing the flow discharge in
water intakes. The present paper investigate sedimentation process
by varying the Manning coefficient "n" by using the SHARC
software along the watercourse in the Dez River. Results indicated
that the optimum "n" within that river range is 0.0315 at which
quantity minimum sediment loads are transported into the Eastern
intake. Comparison of the model results with those obtained by those
from the SSIIM software within the same river reach showed a very
close proximity between them. This suggests a relative accuracy with
which the model can simulate the hydraulic flow characteristics and
therefore its suitability as a powerful analytical tool for project
feasibility studies and project implementation.
Abstract: The aim of this paper is to present a methodology in
three steps to forecast supply chain demand. In first step, various data
mining techniques are applied in order to prepare data for entering
into forecasting models. In second step, the modeling step, an
artificial neural network and support vector machine is presented
after defining Mean Absolute Percentage Error index for measuring
error. The structure of artificial neural network is selected based on
previous researchers' results and in this article the accuracy of
network is increased by using sensitivity analysis. The best forecast
for classical forecasting methods (Moving Average, Exponential
Smoothing, and Exponential Smoothing with Trend) is resulted based
on prepared data and this forecast is compared with result of support
vector machine and proposed artificial neural network. The results
show that artificial neural network can forecast more precisely in
comparison with other methods. Finally, forecasting methods'
stability is analyzed by using raw data and even the effectiveness of
clustering analysis is measured.
Abstract: In this paper, we propose a Perceptually Optimized Foveation based Embedded ZeroTree Image Coder (POEFIC) that introduces a perceptual weighting to wavelet coefficients prior to control SPIHT encoding algorithm in order to reach a targeted bit rate with a perceptual quality improvement with respect to a given bit rate a fixation point which determines the region of interest ROI. The paper also, introduces a new objective quality metric based on a Psychovisual model that integrates the properties of the HVS that plays an important role in our POEFIC quality assessment. Our POEFIC coder is based on a vision model that incorporates various masking effects of human visual system HVS perception. Thus, our coder weights the wavelet coefficients based on that model and attempts to increase the perceptual quality for a given bit rate and observation distance. The perceptual weights for all wavelet subbands are computed based on 1) foveation masking to remove or reduce considerable high frequencies from peripheral regions 2) luminance and Contrast masking, 3) the contrast sensitivity function CSF to achieve the perceptual decomposition weighting. The new perceptually optimized codec has the same complexity as the original SPIHT techniques. However, the experiments results show that our coder demonstrates very good performance in terms of quality measurement.
Abstract: Snake bite cases in Malaysia most often involve the
species Naja-naja and Calloselasma rhodostoma. In keeping with the
need for a rapid snake venom detection kit in a clinical setting, plate
and dot-ELISA test for the venoms of Naja-naja sumatrana,
Calloselasma rhodostoma and the cobra venom fraction V antigen
was developed. Polyclonal antibodies were raised and further used to
prepare the reagents for the dot-ELISA test kit which was tested in
mice, rabbit and virtual human models. The newly developed dot-
ELISA kit was able to detect a minimum venom concentration of
244ng/ml with cross reactivity of one antibody type. The dot-ELISA
system was sensitive and specific for all three snake venom types in
all tested animal models. The lowest minimum venom concentration
detectable was in the rabbit model, 244ng/ml of the cobra venom
fraction V antigen. The highest minimum venom concentration was
in mice, 1953ng/ml against a multitude of venoms. The developed
dot-ELISA system for the detection of three snake venom types was
successful with a sensitivity of 95.8% and specificity of 97.9%.
Abstract: Chemical detection is still a continuous challenge when
it comes to designing single-walled carbon nanotube (SWCNT)
sensors with high selectivity, especially in complex chemical
environments. A perfect example of such an environment would be in
thermally oxidized soybean oil. At elevated temperatures, oil oxidizes
through a series of chemical reactions which results in the formation of
monoacylglycerols, diacylglycerols, oxidized triacylglycerols, dimers,
trimers, polymers, free fatty acids, ketones, aldehydes, alcohols,
esters, and other minor products. In order to detect the rancidity of
oxidized soybean oil, carbon nanotube chemiresistor sensors have
been coated with polyethylenimine (PEI) to enhance the sensitivity
and selectivity. PEI functionalized SWCNTs are known to have a high
selectivity towards strong electron withdrawing molecules. The
sensors were very responsive to different oil oxidation levels and
furthermore, displayed a rapid recovery in ambient air without the
need of heating or UV exposure.
Abstract: Traditional multivariate control charts assume that measurement from manufacturing processes follows a multivariate normal distribution. However, this assumption may not hold or may be difficult to verify because not all the measurement from manufacturing processes are normal distributed in practice. This study develops a new multivariate control chart for monitoring the processes with non-normal data. We propose a mechanism based on integrating the one-class classification method and the adaptive technique. The adaptive technique is used to improve the sensitivity to small shift on one-class classification in statistical process control. In addition, this design provides an easy way to allocate the value of type I error so it is easier to be implemented. Finally, the simulation study and the real data from industry are used to demonstrate the effectiveness of the propose control charts.
Abstract: Speed sensorless systems are intensively studied during recent years; this is mainly due to their economical benefit and fragility of mechanical sensors and also the difficulty of installing this type of sensor in many applications. These systems suffer from instability problems and sensitivity to parameter mismatch at low speed operation. In this paper an analysis of adaptive observer stability with stator resistance estimation is given.
Abstract: This paper proposes view-point insensitive human
pose recognition system using neural network. Recognition system
consists of silhouette image capturing module, data driven database,
and neural network. The advantages of our system are first, it is
possible to capture multiple view-point silhouette images of 3D human
model automatically. This automatic capture module is helpful to
reduce time consuming task of database construction. Second, we
develop huge feature database to offer view-point insensitivity at pose
recognition. Third, we use neural network to recognize human pose
from multiple-view because every pose from each model have similar
feature patterns, even though each model has different appearance and
view-point. To construct database, we need to create 3D human model
using 3D manipulate tools. Contour shape is used to convert silhouette
image to feature vector of 12 degree. This extraction task is processed
semi-automatically, which benefits in that capturing images and
converting to silhouette images from the real capturing environment is
needless. We demonstrate the effectiveness of our approach with
experiments on virtual environment.
Abstract: Along with forward supply chain organization needs
to consider the impact of reverse logistics due to its economic
advantage, social awareness and strict legislations. In this paper, we
develop a system dynamics framework for a closed-loop supply
chain with fuzzy demand and fuzzy collection rate by incorporating
product exchange policy in forward channel and various recovery
options in reverse channel. The uncertainty issues associated with
acquisition and collection of used product have been quantified using
possibility measures. In the simulation study, we analyze order
variation at both retailer and distributor level and compare bullwhip
effects of different logistics participants over time between the
traditional forward supply chain and the closed-loop supply chain.
Our results suggest that the integration of reverse logistics can reduce
order variation and bullwhip effect of a closed-loop system. Finally,
sensitivity analysis is performed to examine the impact of various
parameters on recovery process and bullwhip effect.
Abstract: Breast cancer detection techniques have been reported
to aid radiologists in analyzing mammograms. We note that most
techniques are performed on uncompressed digital mammograms.
Mammogram images are huge in size necessitating the use of
compression to reduce storage/transmission requirements. In this
paper, we present an algorithm for the detection of
microcalcifications in the JPEG2000 domain. The algorithm is based
on the statistical properties of the wavelet transform that the
JPEG2000 coder employs. Simulation results were carried out at
different compression ratios. The sensitivity of this algorithm ranges
from 92% with a false positive rate of 4.7 down to 66% with a false
positive rate of 2.1 using lossless compression and lossy compression
at a compression ratio of 100:1, respectively.
Abstract: In this paper, we consider a designed and
implemented phase-cutting dimmer. In fact, the dimmer is closed
loop and a microcontroller calculates and then regulates the firing
delay angles of each channel. Depending on the firing angle, the
harmonic distortion in the input current will not comply with
international standards, such as IEC 61000-3-2 (class C equipments).
For solving this problem, eight harmonic compensators have been
added to the dimmer. So, the proposed dimmer has a little harmonic
distortion in the input current whereas conventional phase-cutting
dimmers are not so. Sensitivity and removed THD of the proposed
dimmer will be presented.
Abstract: The voltage/current characteristics and the effect of
NO2 gas on the electrical conductivity of a PbPc gas sensor array is
investigated. The gas sensor is manufactured using vacuum
deposition of gold electrodes on sapphire substrate with the leadphathalocyanine
vacuum sublimed on the top of the gold electrodes.
Two versions of the PbPc gas sensor array are investigated. The
tested types differ in the gap sizes between the deposited gold
electrodes. The sensors are tested at different temperatures to account
for conductivity changes as the molecular adsorption/desorption rate
is affected by heat. The obtained results found to be encouraging as
the sensors shoed stability and sensitivity towards low concentration
of applied NO2 gas.
Abstract: The paper discusses a 3D numerical solution of the inverse boundary problem for a continuous casting process of alloy. The main goal of the analysis presented within the paper was to estimate heat fluxes along the external surface of the ingot. The verified information on these fluxes was crucial for a good design of a mould, effective cooling system and generally the whole caster. In the study an enthalpy-porosity technique implemented in Fluent package was used for modeling the solidification process. In this method, the phase change interface was determined on the basis of the liquid fraction approach. In inverse procedure the sensitivity analysis was applied for retrieving boundary conditions. A comparison of the measured and retrieved values showed a high accuracy of the computations. Additionally, the influence of the accuracy of measurements on the estimated heat fluxes was also investigated.
Abstract: Heavy rainfall greatly affects the aerodynamic performance of the aircraft. There are many accidents of aircraft caused by aerodynamic efficiency degradation by heavy rain.
In this Paper we have studied the heavy rain effects on the aerodynamic efficiency of cambered NACA 64-210 and symmetric
NACA 0012 airfoils. Our results show significant increase in drag and decrease in lift. We used preprocessing software gridgen for creation of geometry and mesh, used fluent as solver and techplot as postprocessor. Discrete phase modeling called DPM is used to model the rain particles using two phase flow approach. The rain particles are assumed to be inert.
Both airfoils showed significant decrease in lift and increase in drag in simulated rain environment. The most significant difference between these two airfoils was the NACA 64-210 more sensitivity than NACA 0012 to liquid water content (LWC). We believe that the results showed in this paper will be useful for the designer of the commercial aircrafts and UAVs, and will be helpful for training of the pilots to control the airplanes in heavy rain.
Abstract: The computer modeling is carried out for parameter of
sensitivity of optoelectronic chemical and biosensors, using
phenomena of surface plasmon resonance (SPR). The physical model
of SPR-sensor-s is described with (or without) of modifications of
sensitive gold film surface by a dielectric layer. The variants of
increasing of sensitivity for SPR-biosensors, constructed on the
principle gold – dielectric – biomolecular layer are considered. Two
methods of mathematical treatment of SPR-curve are compared –
traditional, with estimation of sensor-s response as shift of the SPRcurve
minimum and proposed, for system with dielectric layer, using
calculating of the derivative in the point of SPR-curve half-width.
Abstract: The case study deals with the semi-quantitative risk
assessment of water resource earmarked for the emergency supply
of population with drinking water. The risk analysis has been based
on previously identified hazards/sensitivities of the elements
of hydrogeological structure and technological equipment of ground
water resource as well as on the assessment of the levels of hazard,
sensitivity and criticality of individual resource elements in the form
of point indexes. The following potential sources of hazard have
been considered: natural disasters caused by atmospheric and
geological changes, technological hazards, and environmental
burdens. The risk analysis has proved that the assessed risks are
acceptable and the water resource may be integrated into a crisis plan
of a given region.
Abstract: Within the domain of Systems Engineering the need
to perform property aggregation to understand, analyze and manage
complex systems is unequivocal. This can be seen in numerous
domains such as capability analysis, Mission Essential Competencies
(MEC) and Critical Design Features (CDF). Furthermore, the need
to consider uncertainty propagation as well as the sensitivity of
related properties within such analysis is equally as important when
determining a set of critical properties within such a system.
This paper describes this property breakdown in a number of
domains within Systems Engineering and, within the area of CDFs,
emphasizes the importance of uncertainty analysis. As part of this, a
section of the paper describes possible techniques which may be used
within uncertainty propagation and in conclusion an example is
described utilizing one of the techniques for property and uncertainty
aggregation within an aircraft system to aid the determination of
Critical Design Features.
Abstract: Most of the image watermarking methods, using the properties of the human visual system (HVS), have been proposed in literature. The component of the visual threshold is usually related to either the spatial contrast sensitivity function (CSF) or the visual masking. Especially on the contrast masking, most methods have not mention to the effect near to the edge region. Since the HVS is sensitive what happens on the edge area. This paper proposes ultrasound image watermarking using the visual threshold corresponding to the HVS in which the coefficients in a DCT-block have been classified based on the texture, edge, and plain area. This classification method enables not only useful for imperceptibility when the watermark is insert into an image but also achievable a robustness of watermark detection. A comparison of the proposed method with other methods has been carried out which shown that the proposed method robusts to blockwise memoryless manipulations, and also robust against noise addition.
Abstract: The heuristic decision rules used for project
scheduling will vary depending upon the project-s size, complexity,
duration, personnel, and owner requirements. The concept of project
complexity has received little detailed attention. The need to
differentiate between easy and hard problem instances and the
interest in isolating the fundamental factors that determine the
computing effort required by these procedures inspired a number of
researchers to develop various complexity measures.
In this study, the most common measures of project complexity are
presented. A new measure of project complexity is developed. The
main privilege of the proposed measure is that, it considers size,
shape and logic characteristics, time characteristics, resource
demands and availability characteristics as well as number of critical
activities and critical paths. The degree of sensitivity of the proposed
measure for complexity of project networks has been tested and
evaluated against the other measures of complexity of the considered
fifty project networks under consideration in the current study. The
developed measure showed more sensitivity to the changes in the
network data and gives accurate quantified results when comparing
the complexities of networks.
Abstract: This paper discusses two observers, which are used
for the estimation of parameters of PMSM. Former one, reduced
order observer, which is used to estimate the inaccessible parameters
of PMSM. Later one, full order observer, which is used to estimate
all the parameters of PMSM even though some of the parameters are
directly available for measurement, so as to meet with the
insensitivity to the parameter variation. However, the state space
model contains some nonlinear terms i.e. the product of different
state variables. The asymptotic state observer, which approximately
reconstructs the state vector for linear systems without uncertainties,
was presented by Luenberger. In this work, a modified form of such
an observer is used by including a non-linear term involving the
speed. So, both the observers are designed in the framework of
nonlinear control; their stability and rate of convergence is discussed.