Abstract: Influence of octane and benzene on plant cell
ultrastructure and enzymes of basic metabolism, such as nitrogen
assimilation and energy generation have been studied. Different
plants: perennial ryegrass (Lolium perenne) and alfalfa (Medicago
sativa); crops- maize (Zea mays L.) and bean (Phaseolus vulgaris);
shrubs – privet (Ligustrum sempervirens) and trifoliate orange
(Poncirus trifoliate); trees - poplar (Populus deltoides) and white
mulberry (Morus alba L.) were exposed to hydrocarbons of different
concentrations (1, 10 and 100 mM). Destructive changes in bean and
maize leaves cells ultrastructure under the influence of benzene
vapour were revealed at the level of photosynthetic and energy
generation subcellular organells. Different deviations at the level of
subcellular organelles structure and distribution were observed in
alfalfa and ryegrass root cells under the influence of benzene and
octane, absorbed through roots. The level of destructive changes is
concentration dependent. Benzene at low 1 and 10 mM concentration
caused the increase in glutamate dehydrogenase (GDH) activity in
maize roots and leaves and in poplar and mulberry shoots, though to
higher extent in case of lower, 1mM concentration. The induction
was more intensive in plant roots. The highest tested 100mM
concentration of benzene was inhibitory to the enzyme in all plants.
Octane caused induction of GDH in all grassy plants at all tested
concentrations; however the rate of induction decreased parallel to
increase of the hydrocarbon concentration. Octane at concentration 1
mM caused induction of GDH in privet, trifoliate and white mulberry
shoots. The highest, 100mM octane was characterized by inhibitory
effect to GDH activity in all plants. Octane had inductive effect on
malate dehydrogenase in almost all plants and tested concentrations,
indicating the intensification of Trycarboxylic Acid Cycle.
The data could be suggested for elaboration of criteria for plant
selection for phytoremediation of oil hydrocarbons contaminated
soils.
Abstract: Zeolite A and MCM-41 have extensive applications in basic science, petrochemical science, energy conservation/storage, medicine, chemical sensor, air purification, environmentally benign composite structure and waste remediation. However, the use of zeolite A and MCM-41 in these areas, especially environmental remediation, are restricted due to prohibitive production cost. Efficient recycling of and resource recovery from coal fly ash has been a major topic of current international research interest, aimed at achieving sustainable development of human society from the viewpoints of energy, economy, and environmental strategy. This project reported an original, novel, green and fast methods to produce nano-porous zeolite A and MCM-41 materials from coal fly ash. For zeolite A, this novel production method allows a reduction by half of the total production time while maintaining a high degree of crystallinity of zeolite A which exists in a narrower particle size distribution. For MCM-41, this remarkably green approach, being an environmentally friendly process and reducing generation of toxic waste, can produce pure and long-range ordered MCM-41 materials from coal fly ash. This approach took 24 h at 25 oC to produce 9 g of MCM-41 materials from 30 g of the coal fly ash, which is the shortest time and lowest reaction temperature required to produce pure and ordered MCM-41 materials (having the largest internal surface area) compared to the values reported in the literature. Performance evaluation of the produced zeolite A and MCM-41 materials in wastewater treatment and air pollution control were reported. The residual fly ash was also converted to zeolite Na-P1 which showed good performance in removal of multi-metal ions in wastewater. In wastewater treatment, compared to commercial-grade zeolite A, adsorbents produced from coal fly ash were effective in removing multi heavy metal ions in water and could be an alternative material for treatment of wastewater. In methane emission abatement, the zeolite A (produced from coal fly ash) achieved similar methane removal efficiency compared to the zeolite A prepared from pure chemicals. This report provides the guidance for production of zeolite A and MCM-41 from coal fly ash by a cost-effective approach which opens potential applications of these materials in environmental industry. Finally, environmental and economic aspects of production of zeolite A and MCM-41 from coal fly ash were discussed.
Abstract: The remediation of water resources pollution in
developing countries requires the application of alternative
sustainable cheaper and efficient end-of-pipe wastewater treatment
technologies. The feasibility of use of South African cheap and
abundant pine tree (Pinus patula) sawdust for development of lowcost
AC of comparable quality to expensive commercial ACs in the
abatement of water pollution was investigated. AC was developed at
optimized two-stage N2-superheated steam activation conditions in a
fixed bed reactor, and characterized for proximate and ultimate
properties, N2-BET surface area, pore size distribution, SEM, pHPZC
and FTIR. The sawdust pyrolysis activation energy was evaluated by
TGA. Results indicated that the chars prepared at 800oC and 2hrs
were suitable for development of better quality AC at 800oC and 47%
burn-off having BET surface area (1086m2/g), micropore volume
(0.26cm3/g), and mesopore volume (0.43cm3/g) comparable to
expensive commercial ACs, and suitable for water contaminants
removal. The developed AC showed basic surface functionality at
pHPZC at 10.3, and a phenol adsorption capacity that was higher than
that of commercial Norit (RO 0.8) AC. Thus, it is feasible to develop
better quality low-cost AC from (Pinus patula) sawdust using twostage
N2-steam activation in fixed-bed reactor.
Abstract: Palladium-catalyzed hydrodechlorination is a
promising alternative for the treatment of environmentally relevant
water bodies, such as groundwater, contaminated with chlorinated
organic compounds (COCs). In the aqueous phase
hydrodechlorination of COCs, Pd-based catalysts were found to have
a very high catalytic activity. However, the full utilization of the
catalyst-s potential is impeded by the sensitivity of the catalyst to
poisoning and deactivation induced by reduced sulfur compounds
(e.g. sulfides). Several regenerants have been tested before to recover
the performance of sulfide-fouled Pd catalyst. But these only
delivered partial success with respect to re-establishment of the
catalyst activity. In this study, the deactivation behaviour of
Pd/Al2O3 in the presence of sulfide was investigated. Subsequent to
total deactivation the catalyst was regenerated in the aqueous phase
using potassium permanganate. Under neutral pH condition,
oxidative regeneration with permanganate delivered a slow recovery
of catalyst activity. However, changing the pH of the bulk solution to
acidic resulted in the complete recovery of catalyst activity within a
regeneration time of about half an hour. These findings suggest the
superiority of permanganate as regenerant in re-activating Pd/Al2O3
by oxidizing Pd-bound sulfide.
Abstract: Coal will continue to be the predominant source of
global energy for coming several decades. The huge generation of fly
ash (FA) from combustion of coal in thermal power plants (TPPs) is
apprehended to pose the concerns of its disposal and utilization. FA
application based on its typical characteristics as soil ameliorant for
agriculture and forestry is the potential area, and hence the global
attempt. The inferences drawn suffer from the variations of ash
characteristics, soil types, and agro-climatic conditions; thereby
correlating the effects of ash between various plant species and soil
types is difficult. Indian FAs have low bulk density, high water
holding capacity and porosity, rich silt-sized particles, alkaline
nature, negligible solubility, and reasonable plant nutrients. Findings
of the demonstrations trials for more than two decades from lab/pot
to field scale long-term experiments are developed as FA soil
amendment technology (FASAT) by Central Institute of Mining and
Fuel Research (CIMFR), Dhanbad. Performance of different crops
and plant species in cultivable and problematic soils, are
encouraging, eco-friendly, and being adopted by the farmers. FA
application includes ash alone and in combination with
inorganic/organic amendments; combination treatments including
bio-solids perform better than FA alone. Optimum dose being up to
100 t/ha for cultivable land and up to/ or above 200 t/ha of FA for
waste/degraded land/mine refuse, depending on the characteristics of
ash and soil. The elemental toxicity in Indian FA is usually not of
much concern owing to alkaline ashes, oxide forms of elements, and
elemental concentration within the threshold limits for soil
application. Combating toxicity, if any, is possible through
combination treatments with organic materials and phytoremediation.
Government initiatives through extension programme
involving farmers and ash generating organizations need to be
accelerated
Abstract: An attempt was made for availability of wastewater reuse/reclamation for irrigation purposes using phytoremediation “the low cost and less technology", using six local aquatic macrophytes “e.g. T. angustifolia, B. maritimus, Ph. australis, A. donax, A. plantago-aquatica and M. longifolia (Linn)" as biological waste purifiers. Outdoor experiments/designs were conducted from May 03, 2007 till October 15, 2008, close to one of the main sewage channels of Sulaimani City/Iraq*. All processes were mainly based on conventional wastewater treatment processes, besides two further modifications were tested, the first was sand filtration pots, implanted by individual species of experimental macrophytes and the second was constructed wetlands implanted by experimental macrophytes all together. Untreated and treated wastewater samples were analyzed for their key physico-chemical properties (only heavy metals Fe, Mn, Zn and Cu with particular reference to removal efficiency by experimental macrophytes are highlighted in this paper). On the other hand, vertical contents of heavy metals were also evaluated from both pots and the cells of constructed wetland. After 135 days, macrophytes were harvested and heavy metals were analyzed in their biomass (roots/shoots) for removal efficiency assessment (i.e. uptake/ bioaccumulation rate). Results showed that; removal efficiency of all studied heavy metals was much higher in T. angustifolia followed by Ph. Australis, B. maritimus and A. donax in triple experiment sand pots. Constructed wetland experiments have revealed that; the more replicated constructed wetland cells the highest heavy metal removal efficiency was indicated.
Abstract: A research project dealing with the phytoremediation
of a soil polluted by some heavy metals is currently running. The
case study is represented by a mining area in Hamedan province in
the central west part of Iran. The potential of phytoextraction and
phytostabilization of plants was evaluated considering the
concentration of heavy metals in the plant tissues and also the
bioconcentration factor (BCF) and the translocation factor (TF). Also
the several established criteria were applied to define
hyperaccumulator plants in the studied area. Results showed that
none of the collected plant species were suitable for phytoextraction
of Cu, Zn, Fe and Mn, but among the plants, Euphorbia macroclada
was the most efficient in phytostabilization of Cu and Fe, while,
Ziziphora clinopodioides, Cousinia sp. and Chenopodium botrys
were the most suitable for phytostabilization of Zn and Chondrila
juncea and Stipa barbata had the potential for phytostabilization of
Mn. Using the most common criterion, Euphorbia macroclada and
Verbascum speciosum were Fe hyperaccumulator plants. Present
study showed that native plant species growing on contaminated sites
may have the potential for phytoremediation.
Abstract: Water hyacinth has been used in aquatic systems for
wastewater purification in many years worldwide. The role of water
hyacinth (Eichhornia crassipes) species in polishing nitrate and
phosphorus concentration from municipal wastewater treatment plant
effluent by phytoremediation method was evaluated. The objective
of this project is to determine the removal efficiency of water
hyacinth in polishing nitrate and phosphorus, as well as chemical
oxygen demand (COD) and ammonia. Water hyacinth is considered
as the most efficient aquatic plant used in removing vast range of
pollutants such as organic matters, nutrients and heavy metals. Water
hyacinth, also referred as macrophytes, were cultivated in the
treatment house in a reactor tank of approximately 90(L) x 40(W) x
25(H) in dimension and built with three compartments. Three water
hyacinths were placed in each compartments and water sample in
each compartment were collected in every two days. The plant
observation was conducted by weight measurement, plant uptake and
new young shoot development. Water hyacinth effectively removed
approximately 49% of COD, 81% of ammonia, 67% of phosphorus
and 92% of nitrate. It also showed significant growth rate at starting
from day 6 with 0.33 shoot/day and they kept developing up to 0.38
shoot/day at the end of day 24. From the studies conducted, it was
proved that water hyacinth is capable of polishing the effluent of
municipal wastewater which contains undesirable amount of nitrate
and phosphorus concentration.
Abstract: Contamination of heavy metals represents one of the
most pressing threats to water and soil resources as well as human
health. Phytoremediation can be potentially used to remediate metalcontaminated
sites. A major step towards the development of
phytoremediation of heavy metal impacted soils is the discovery of
the heavy metal hyperaccumulation in plants. In this study, the
several established criteria to define a hyperaccumulator plant were
applied. The case study was represented by a mining area in
Hamedan province in the central west part of Iran. Obtained results
showed that the most of sampled species were able to grow on
heavily metal-contaminated soils and also were able to accumulate
extraordinarily high concentrations of some metals such as Zn, Mn,
Cu, Pb and Fe. Using the most common criteria, Euphorbia
macroclada and Centaurea virgata can be classified as
hyperaccumulators of some measured heavy metals and, therefore,
they have suitable potential for phytoremediation of contaminated
soils.
Abstract: Mercury adsorption on soil was investigated at
different ionic strengths using Ca(NO3)2 as a background electrolyte.
Results fitted the Langmuir equation and the adsorption isotherms
reached a plateau at higher equilibrium concentrations. Increasing
ionic strength decreased the sorption of mercury, due to the
competition of Ca ions for the sorption sites in the soils. The
influence of ionic strength was related to the mechanisms of heavy
metal sorption by the soil. These results can be of practical
importance both in the agriculture and contaminated soils since the
solubility of mercury in soils are strictly dependent on the adsorption
and release process.
Abstract: Although oil-based drilling fluids are of paramount practical and economical interest, they represent a serious source of pollution, once released into the environment as drill cuttings. The aim of this study is to assess the capability of isolated microorganisms to degrade gasoil fuel. The commonly used physicochemical and biodegradation remediation techniques of petroleum contaminated soil were both investigated. The study revealed that natural biodegradation is favorable. Even though, the presence of heavy metals, the moisture level of (8.55%) and nutrient deficiencies put severe constrains on microorganisms- survival ranges inhibiting the biodegradation process. The selected strains were able to degrade the diesel fuel at significantly high rates (around 98%).
Abstract: In this study, the designed dual stage membrane
bioreactor (MBR) system was conceptualized for the treatment of
cyanide and heavy metals in electroplating wastewater. The design
consisted of a primary treatment stage to reduce the impact of
fluctuations and the secondary treatment stage to remove the residual
cyanide and heavy metal contaminants in the wastewater under
alkaline pH conditions. The primary treatment stage contained
hydrolyzed Citrus sinensis (C. sinensis) pomace and the secondary
treatment stage contained active Aspergillus awamori (A. awamori)
biomass, supplemented solely with C. sinensis pomace extract from
the hydrolysis process. An average of 76.37%, 95.37%, 93.26 and
94.76% and 99.55%, 99.91%, 99.92% and 99.92% degradation
efficiency for total cyanide (T-CN), including the sorption of nickel
(Ni), zinc (Zn) and copper (Cu) were observed after the first and
second treatment stages, respectively. Furthermore, cyanide
conversion by-products degradation was 99.81% and 99.75 for both
formate (CHOO-) and ammonium (NH4
+) after the second treatment
stage. After the first, second and third regeneration cycles of the C.
sinensis pomace in the first treatment stage, Ni, Zn and Cu removal
achieved was 99.13%, 99.12% and 99.04% (first regeneration cycle),
98.94%, 98.92% and 98.41% (second regeneration cycle) and 98.46
%, 98.44% and 97.91% (third regeneration cycle), respectively.
There was relatively insignificant standard deviation detected in all
the measured parameters in the system which indicated
reproducibility of the remediation efficiency in this continuous
system.
Abstract: Contamination of aromatic compounds in water can
cause severe long-lasting effects not only for biotic organism but also
on human health. Several alternative technologies for remediation of
polluted water have been attempted. One of these is adsorption
process of aromatic compounds by using organic modified clay
mineral. Porous structure of clay is potential properties for molecular
adsorptivity and it can be increased by immobilizing hydrophobic
structure to attract organic compounds. In this work natural
montmorillonite were modified with cetyltrimethylammonium
(CTMA+) and was evaluated for use as adsorbents of aromatic
compounds: benzene, toluene, and 2-chloro phenol in its single and
multicomponent solution by ethanol:water solvent. Preparation of
CTMA-montmorillonite was conducted by simple ion exchange
procedure and characterization was conducted by using x-day
diffraction (XRD), Fourier-transform infra red (FTIR) and gas
sorption analysis. The influence of structural modification of
montmorillonite on its adsorption capacity and adsorption affinity of
organic compound were studied. It was shown that adsorptivity of
montmorillonite was increased by modification associated with
arrangements of CTMA+ in the structure even the specific surface
area of modified montmorillonite was lower than raw
montmorillonite. Adsorption rate indicated that material has affinity
to adsorb compound by following order: benzene> toluene > 2-chloro
phenol. The adsorption isotherms of benzene and toluene showed 1st
order adsorption kinetic indicating a partition phenomenon of
compounds between the aqueous and organophilic CTMAmontmorillonite.
Abstract: In the present work we report a gram negative
bacterial isolate, from soil of a dye industry, with promising
biorefining and bioremediation potential. This isolate (GBS.5) could
utilize carbazole (nitrogen containing polycyclic aromatic
hydrocarbon) as the sole source of nitrogen and carbon and utilize
almost 98% of 3mM carbazole in 100 hours. The specific activity of
our GBS.5 isolate for carbazole degradation at 30°C and pH 7.0 was
found to be 11.36 μmol/min/g dry cell weight as compared to 10.4
μmol/min/g dry cell weight, the highest reported specific activity till
date. The presence of car genes (the genes involved in
denitrogenation of carbazole) was confirmed through PCR
amplification.
Abstract: The assessment of surface waters in Enugu metropolis
for fecal coliform bacteria was undertaken. Enugu urban was divided
into three areas (A1, A2 and A3), and fecal coliform bacteria
analysed in the surface waters found in these areas for four years
(2005-2008). The plate count method was used for the analyses. Data
generated were subjected to statistical tests involving; Normality test,
Homogeneity of variance test, correlation test, and tolerance limit
test. The influence of seasonality and pollution trends were
investigated using time series plots. Results from the tolerance limit
test at 95% coverage with 95% confidence, and with respect to EU
maximum permissible concentration show that the three areas suffer
from fecal coliform pollution. To this end, remediation procedure
involving the use of saw-dust extracts from three woods namely;
Chlorophora-Excelsa (C-Excelsa),Khayan-Senegalensis,(CSenegalensis)
and Erythrophylum-Ivorensis (E-Ivorensis) in
controlling the coliforms was studied. Results show that mixture of
the acetone extracts of the woods show the most effective
antibacterial inhibitory activities (26.00mm zone of inhibition)
against E-coli. Methanol extract mixture of the three woods gave best
inhibitory activity (26.00mm zone of inhibition) against S-areus, and
25.00mm zones of inhibition against E-Aerogenes. The aqueous
extracts mixture gave acceptable zones of inhibitions against the
three bacteria organisms.
Abstract: The aim of this work was to investigate the potential of soil microorganisms and the burhead plant, as well as the combination of soil microorganisms and plants to remediate monoethylene glycol (MEG), diethylene glycol (DEG), and triethylene glycol (TEG) in synthetic wastewater. The result showed that a system containing both burhead plant and soil microorganisms had the highest efficiency in EGs removal. Around 100% of MEG and DEG and 85% of TEG were removed within 15 days of the experiments. However, the burhead plant had higher removal efficiency than soil microorganisms for MEG and DEG but the same for TEG in the study systems. The removal rate of EGs in the study system related to the molecular weight of the compounds and MEG, the smallest glycol, was removed faster than DEG and TEG by both the burhead plant and soil microorganisms in the study system.