Abstract: Diesel Engines emit complex mixtures of inorganic
and organic compounds in the form of both solid and vapour phase
particles. Most of the particulates released are ultrafine nanoparticles
which are detrimental to human health and can easily enter the body
by respiration. The emissions standards on particulate matter release
from diesel engines are constantly upgraded within the European
Union and with future regulations based on the particles numbers
released instead of merely mass, the need for effective aftertreatment
devices will increase. Standard particulate filters in the form of wall
flow filters can have problems with high soot accumulation,
producing a large exhaust backpressure. A potential solution would
be to combine the standard filter with a flow through filter to reduce
the load on the wall flow filter. In this paper soot particle trapping has
been simulated in different continuous flow filters of monolithic
structure including the use of promoters, at laminar flow conditions.
An Euler Lagrange model, the discrete phase model in Ansys used
with user defined functions for forces acting on particles. A method
to quickly screen trapping of 5 nm and 10 nm particles in different
catalysts designs with tracers was also developed.
Simulations of square duct monoliths with promoters show that the
strength of the vortices produced are not enough to give a high
amount of particle deposition on the catalyst walls. The smallest
particles in the simulations, 5 and 10 nm particles were trapped to a
higher extent, than larger particles up to 1000 nm, in all studied
geometries with the predominant deposition mechanism being
Brownian diffusion. The comparison of the different filters designed
with a wall flow filter does show that the options for altering a design
of a flow through filter, without imposing a too large pressure drop
penalty are good.
Abstract: The performance of high-resolution schemes is investigated for unsteady, inviscid and compressible multiphase flows. An Eulerian diffuse interface approach has been chosen for the simulation of multicomponent flow problems. The reduced fiveequation and seven equation models are used with HLL and HLLC approximation. The authors demonstrated the advantages and disadvantages of both seven equations and five equations models studying their performance with HLL and HLLC algorithms on simple test case. The seven equation model is based on two pressure, two velocity concept of Baer–Nunziato [10], while five equation model is based on the mixture velocity and pressure. The numerical evaluations of two variants of Riemann solvers have been conducted for the classical one-dimensional air-water shock tube and compared with analytical solution for error analysis.
Abstract: The effect of autofrettage process in strain hardened
thick-walled pressure vessels has been investigated theoretically by
finite element modeling. Equivalent von Mises stress is used as yield
criterion to evaluate the optimum autofrettage pressure and the
optimum radius of elastic-plastic junction. It has been observed that
the optimum autofrettage pressure increases along with the working
pressure. For two different working pressures, the effect of the ratio
of outer to inner radius (b/a=k) value on the optimum autofrettage
pressure is also noticed. The Optimum autofrettage pressure solely
depends on K value rather than on the inner or outer radius.
Furthermore, percentage reduction of von Mises stresses is compared
for different working pressures and different k values. Maximum von
Mises stress developed at different autofrettage pressure is equated
for elastic perfectly plastic and elastic-plastic material with different
slope of strain hardening segment. Cylinder material having higher
slope of strain hardening segment provides better benedictions in the
autofrettage process.
Abstract: Acoustic function plays an important role in
aerodynamic mechanical engineering. It can classify the kind of
air-vehicle such as subsonic or supersonic. Acoustic velocity
relates with velocity and Mach number. Mach number relates
again acoustic stability or instability condition. Mach number
plays an important role in growth or decay in energy system.
Acoustic is a function of temperature and temperature is directly
proportional to pressure. If we control the pressure, we can control
acoustic function. To get pressure stability condition, we apply
Navier-Stokes equations.
Abstract: α-Pinene is the main component of the most
turpentine oils. The hydration of α-pinene with acid catalysts leads to
a complex mixture of monoterpenes. In order to obtain more valuable
products, the α-pinene in the turpentine can be hydrated in dilute
mineral acid solutions to produce α-terpineol. The design of
separation processes requires information on phase equilibrium and
related thermodynamic properties. This paper reports the results of
study on liquid-liquid equilibrium (LLE) of system containing α-
pinene + water and α-terpineol + water.
Binary LLE for α-pinene + water system, and α-terpineol + water
systems were determined by experiment at 301K and atmospheric
pressure. The two component mixture was stirred for about 30min,
then the mixture was left for about 2h for complete phase separation.
The composition of both phases was analyzed by using a Gas
Chromatograph. The experimental data were correlated by
considering both NRTL and UNIQUAC activity coefficient models.
The LLE data for the system of α-pinene + water and α-terpineol +
water were correlated successfully by the NRTL model. The
experimental data were not satisfactorily fitted by the UNIQUAC
model. The NRTL model (α =0.3) correlates the LLE data for the
system of α-pinene + water at 301K with RMSD of 0.0404%. And
the NRTL model (α =0.61) at 301K with RMSD of 0.0058 %. The
NRTL model (α =0.3) correlates the LLE data for the system of α-
terpineol + water at 301K with RMSD of 0.1487% and the NRTL
model (α =0.6) at 301K with RMSD of 0.0032%, between the
experimental and calculated mole fractions.
Abstract: The operating control parameters of injection
flushing type of electrical discharge machining process on stainless
steel 304 workpiece with copper tools are being optimized
according to its individual machining characteristic i.e. material
removal rate (MRR). Lower MRR during EDM machining process
may decrease its- machining productivity. Hence, the quality
characteristic for MRR is set to higher-the-better to achieve the
optimum machining productivity. Taguchi method has been used
for the construction, layout and analysis of the experiment for each
of the machining characteristic for the MRR. The use of Taguchi
method in the experiment saves a lot of time and cost of preparing
and machining the experiment samples. Therefore, an L18
Orthogonal array which was the fundamental component in the
statistical design of experiments has been used to plan the
experiments and Analysis of Variance (ANOVA) is used to
determine the optimum machining parameters for this machining
characteristic. The control parameters selected for this
optimization experiments are polarity, pulse on duration, discharge
current, discharge voltage, machining depth, machining diameter
and dielectric liquid pressure. The result had shown that the higher
the discharge voltage, the higher will be the MRR.
Abstract: The influence of eccentric discharge of stored solids in
squat silos has been highly valued by many researchers. However,
calculation method of lateral pressure under eccentric flowing still
needs to be deeply studied. In particular, the lateral pressure
distribution on vertical wall could not be accurately recognized
mainly because of its asymmetry. In order to build mechanical model
of lateral pressure, flow channel and flow pattern of stored solids in
squat silo are studied. In this passage, based on Janssen-s theory, the
method for calculating lateral static pressure in squat silos after
eccentric discharge is proposed. Calculative formulae are deduced for
each of three possible cases. This method is also focusing on
unsymmetrical distribution characteristic of silo wall normal
pressure. Finite element model is used to analysis and compare the
results of lateral pressure and the numerical results illustrate the
practicability of the theoretical method.
Abstract: Hydrodynamic pressures acting on upstream of concrete dams during an earthquake are an important factor in designing and assessing the safety of these structures in Earthquake regions. Due to inherent complexities, assessing exact hydrodynamic pressure is only feasible for problems with simple geometry. In this research, the governing equation of concrete gravity dam reservoirs with effect of fluid viscosity in frequency domain is solved and then compared with that in which viscosity is assumed zero. The results show that viscosity influences the reservoir-s natural frequency. In excitation frequencies near the reservoir's natural frequencies, hydrodynamic pressure has a considerable difference in compare to the results of non-viscose fluid.
Abstract: Biomechanical properties of infantile aorta in vitro in
cases of different standard anastomoses: end-to-end (ETE), extended
anastomosis end-to-end (EETE) and subclavian flap aortoplasty
(SFA) used for surgical correction of coarctation were analyzed to
detect the influence of the method on the biomechanics of infantile
aorta and possible changes in haemodinamics. 10 specimens of native
aorta, 3 specimens with ETE, 4 EEET and 3 SFA were investigated.
The experiments showed a non-linear relationship between stress and
strain in the infantile aorta, the modulus of elasticity of the aortic wall
increased with the increase of inner pressure. In the case of
anastomosis end-to-end the modulus was almost constant, relevant to
the modulus of elasticity of the aorta with the inner pressure 100-120
mmHg. The anastomoses EETE and SFA showed elastic properties
closer to native aorta, the stiffness of ETE did not change with the
changes in inner pressure.
Abstract: A parametric study of a mixed-compression
supersonic inlet is performed and reported. The effects of inlet Mach
Numbers, varying from 4 to 10, and angle of attack, varying from 0
to 10, are reported for a constant inlet dynamic pressure. The paper
looked at the variations of mass flow rates through the inlet, gain in
entropy through the inlet, and the angles of the external oblique
shocks. The mass flow rates were found to decrease monotonically
with Mach numbers and increase with angle of attacks. On the other
hand the entropy gain through the inlet increased with increasing
Mach number and angle of attack. The variation in static pressure
was found to be identical from the inlet throat to the exit for Mach
number values higher than 6.
Abstract: In this research, a systematic investigation was carried out to determine the optimum conditions of HDS reactor. Moreover, a suitable model was developed for a rigorous RTO (real time optimization) loop of HDS (Hydro desulfurization) process. A systematic experimental series was designed based on CCD (Central Composite design) and carried out in the related pilot plant to tune the develop model. The designed variables in the experiments were Temperature, LHSV and pressure. However, the hydrogen over fresh feed ratio was remained constant. The ranges of these variables were respectively equal to 320-380ºC, 1- 21/hr and 50-55 bar. a power law kinetic model was also developed for our further research in the future .The rate order and activation energy , power of reactant concentration and frequency factor of this model was respectively equal to 1.4, 92.66 kJ/mol and k0=2.7*109 .
Abstract: Continuous measurements and multivariate methods are applied in researching the effects of energy consumption on indoor air quality (IAQ) in a Finnish one-family house. Measured data used in this study was collected continuously in a house in Kuopio, Eastern Finland, during fourteen months long period. Consumption parameters measured were the consumptions of district heat, electricity and water. Indoor parameters gathered were temperature, relative humidity (RH), the concentrations of carbon dioxide (CO2) and carbon monoxide (CO) and differential air pressure. In this study, self-organizing map (SOM) and Sammon's mapping were applied to resolve the effects of energy consumption on indoor air quality. Namely, the SOM was qualified as a suitable method having a property to summarize the multivariable dependencies into easily observable two-dimensional map. Accompanying that, the Sammon's mapping method was used to cluster pre-processed data to find similarities of the variables, expressing distances and groups in the data. The methods used were able to distinguish 7 different clusters characterizing indoor air quality and energy efficiency in the study house. The results indicate, that the cost implications in euros of heating and electricity energy vary according to the differential pressure, concentration of carbon dioxide, temperature and season.
Abstract: In aircraft applications, according to the nature of
electrical equipment its location may be in unpressurized area or very
close to the engine; thus, the environmental conditions may change
from atmospheric pressure to less than 100 mbar, and the temperature
may be higher than the ambient one as in most real working
conditions of electrical equipment. Then, the classical Paschen curve
has to be replotted since these parameters may affect the discharge
ignition voltage. In this paper, we firstly investigate the domain of
validity of two corrective expressions on the Paschen-s law found in
the literature, in case of changing the air environment and known as
Peek and Dunbar corrections. Results show that these corrections are
no longer valid for combined variation of temperature and pressure.
After that, a new empirical expression for breakdown voltage is
proposed and is validated in the case of combined variations of
temperature and pressure.
Abstract: Based on the thermodynamic theory, the dependence of
sublimation energy of metal on temperature and pressure is discussed,
and the results indicate that the sublimation energy decreases linearly
with the increase of temperature and pressure. Combined with this
result, the blow-off impulse of aluminum induced by pulsed X-ray is
simulated by smoothed particle hydrodynamics (SPH) method. The
numerical results show that, while the change of sublimation energy
with temperature and pressure is considered, the blow-off impulse of
aluminum is larger than the case that the sublimation energy is
assumed to be a constant.
Abstract: During the last few years, several sheet hydroforming
processes have been introduced. Despite the advantages of these
methods, they have some limitations. Of the processes, the two main
ones are the standard hydroforming and hydromechanical deep
drawing. A new sheet hydroforming die set was proposed that has the
advantages of both processes and eliminates their limitations. In this
method, a polyurethane plate was used as a part of the die-set to
control the blank holder force. This paper outlines the Taguchi
optimization methodology, which is applied to optimize the effective
parameters in forming cylindrical cups by the new die set of sheet
hydroforming process. The process parameters evaluated in this
research are polyurethane hardness, polyurethane thickness, forming
pressure path and polyurethane hole diameter. The design of
experiments based upon L9 orthogonal arrays by Taguchi was used
and analysis of variance (ANOVA) was employed to analyze the
effect of these parameters on the forming pressure. The analysis of
the results showed that the optimal combination for low forming
pressure is harder polyurethane, bigger diameter of polyurethane hole
and thinner polyurethane. Finally, the confirmation test was derived
based on the optimal combination of parameters and it was shown
that the Taguchi method is suitable to examine the optimization
process.
Abstract: At the end of the 20th century it was actual the
development of transport corridors and the improvement of their
technical parameters. With this purpose, many countries and Georgia
among them manufacture to construct new highways, railways and
also reconstruction-modernization of the existing transport
infrastructure. It is necessary to explore the artificial structures
(bridges and tunnels) on the existing tracks as they are very old.
Conference report includes the peculiarities of reconstruction of
tunnels, because we think that this theme is important for the
modernization of the existing road infrastructure. We must remark
that the methods of determining mining pressure of tunnel
reconstructions are worked out according to the jobs of new tunnels
but it is necessary to foresee additional mining pressure which will be
formed during their reconstruction. In this report there are given the
methods of figuring the additional mining pressure while
reconstruction of tunnels, there was worked out the computer
program, it is determined that during reconstruction of tunnels the
additional mining pressure is 1/3rd of main mining pressure.
Abstract: New regulations and standards for noise emission increasingly compel the automotive firms to make some improvements about decreasing the engine noise. Nowadays, the perforated reactive mufflers which have an effective damping capability are specifically used for this purpose. New designs should be analyzed with respect to both acoustics and back pressure. In this study, a reactive perforated muffler is investigated numerically and experimentally. For an acoustical analysis, the transmission loss which is independent of sound source of the present cross flow, the perforated muffler was analyzed by COMSOL. To be able to validate the numerical results, transmission loss was measured experimentally. Back pressure was obtained based on the flow field analysis and was also compared with experimental results. Numerical results have an approximate error of 20% compared to experimental results.
Abstract: In this paper, algorithm estimating the blood pressure
was proposed using the pulse transit time (PTT) as a more convenient
method of measuring the blood pressure. After measuring ECG and
pressure pulse, and photoplethysmography, the PTT was calculated
from the acquired signals. Thereafter, the system to indirectly measure
the systolic pressure and the diastolic pressure was composed using
the statistic method. In comparison between the blood pressure
indirectly measured by proposed algorithm estimating the blood
pressure and real blood pressure measured by conventional
sphygmomanometer, the systolic pressure indicates the mean error of
±3.24mmHg and the standard deviation of 2.53mmHg, while the
diastolic pressure indicates the satisfactory result, that is, the mean
error of ±1.80mmHg and the standard deviation of 1.39mmHg. These
results are satisfied with the regulation of ANSI/AAMI for
certification of sphygmomanometer that real measurement error value
should be within the mean error of ±5mmHg and the standard
deviation of 8mmHg. These results are suggest the possibility of
applying to portable and long time blood pressure monitoring system
hereafter.
Abstract: Carbon dioxide is one of the major green house gases.
It is removed from different streams using amine absorption process.
Sterically hindered amines are suggested as good CO2 absorbers.
Solubility of carbon dioxide (CO2) was measured in aqueous
solutions of 2-Amino-2-methyl-1-propanol (AMP) at temperatures 30
oC, 40 oC and 60 oC. The effect of pressure and temperature was
studied over various concentrations of AMP. It has been found that
pressure has positive effect on CO2 solubility where as solubility
decreased with increasing temperature. Absorption performance of
AMP increased with increasing pressure. Solubility of aqueous AMP
was compared with mo-ethanolamine (MEA) and the absorption
capacity of aqueous solutions of AMP was found to be better.
Abstract: Medical compression bandages are widely used in the
treatment of chronic venous disorder. In order to design effective
compression bandages, researchers have attempted to describe the
interface pressure applied by multi-layer bandages using mathematical
models. This paper reports on the work carried out to
compare and validate the mathematical models used to describe the
interface pressure applied by multi-layer bandages. Both analytical
and experimental results showed that using simple multiplication
of a number of bandage layers with the pressure applied by one
layer of bandage or ignoring the increase in the limb radius due to
former layers of bandage will result in overestimating the pressure.
Experimental results showed that the mathematical models, which
take into consideration the increase in the limb radius due to former
bandage layers, are more accurate than the one which does not.