Abstract: Team distillation assisted by microwave extraction
(SDAM) considered as accelerated technique extraction is a
combination of microwave heating and steam distillation, performed
at atmospheric pressure. SDAM has been compared with the same
technique coupled with the cryogrinding of seeds (SDAM -CG).
Isolation and concentration of volatile compounds are performed by a
single stage for the extraction of essential oil from Cuminum
cyminum seeds. The essential oils extracted by these two methods for
5 min were quantitatively (yield) and qualitatively (aromatic profile)
no similar. These methods yield an essential oil with higher amounts
of more valuable oxygenated compounds, and allow substantial
savings of costs, in terms of time, energy and plant material. SDAM
and SDAM-CG is a green technology and appears as a good
alternative for the extraction of essential oils from aromatic plants.
Abstract: In this study, we developed a model to predict the
temperature and the pressure variation in an internal combustion
engine operated in HCCI (Homogeneous charge compression ignition)
mode. HCCI operation begins from aspirating of homogeneous charge
mixture through intake valve like SI (Spark ignition) engine and the
premixed charge is compressed until temperature and pressure of
mixture reach autoignition point like diesel engine. Combustion phase
was described by double-Wiebe function. The single zone model
coupled with an double-Wiebe function were performed to simulated
pressure and temperature between the period of IVC (Inlet valve close)
and EVO (Exhaust valve open). Mixture gas properties were
implemented using STANJAN and transfer the results to main model.
The model has considered the engine geometry and enables varying in
fuelling, equivalence ratio, manifold temperature and pressure. The
results were compared with the experiment and showed good
correlation with respect to combustion phasing, pressure rise, peak
pressure and temperature. This model could be adapted and use to
control start of combustion for HCCI engine.
Abstract: The present study conducted experimental investigation on combustion and emission characteristics of compression ignition engine using diesel as pilot fuel and methane, hydrogen and methane/hydrogen mixture as gaseous fuels at 1800 rev min-1. The effect of gaseous fuel on peak cylinder pressure and heat release is modest at low to medium loads. At high load, the high combustion temperature and high quantity of pilot fuel contribute to better combustion efficiency for all kinds of gaseous fuels and increases the peak cylinder pressure. Enrichment of hydrogen in methane gradually increases the peak cylinder pressure. The brake thermal efficiency increases with higher hydrogen fraction at lower loads. Hydrogen addition in methane contributed to a proportional reduction of CO/CO2/HC emission without penalty of NOx. For particulate emission, methane and hydrogen, could both suppress the particle emission. 30% hydrogen fraction in methane is observed to be best in reducing the particulate emission.
Abstract: An adaptive Helmholtz resonator was designed and
adapted to hydraulics. The resonator was controlled by open- and
closed-loop controls so that 20 dB attenuation of the peak-to-peak
value of the pulsating pressure was maintained. The closed-loop
control was noted to be better, albeit it was slower because of its low
pressure and temperature variation, which caused variation in the
effective bulk modulus of the hydraulic system. Low-pressure
hydraulics contains air, which affects the stiffness of the hydraulics,
and temperature variation changes the viscosity of the oil. Thus, an
open-loop control loses its efficiency if a condition such as
temperature or the amount of air changes after calibration. The
instability of the low-pressure hydraulic system reduced the
operational frequency range of the Helmholtz resonator when
compared with the results of an analytical model.
Different dampers for hydraulics are presented. Then analytical
models of a hydraulic pipe and a hydraulic pipe with a Helmholtz
resonator are presented. The analytical models are based on the wave
equation of sound pressure. Finally, control methods and the results
of experiments are presented.
Abstract: In this work, Experimental tie-line results and
solubility (binodal) curves were obtained for the ternary systems
(water + acetic acid + methyl isobutyl ketone (MIBK)), (water +
lactic acid+ methyl isobutyl ketone) at T = 294.15K and atmospheric
pressure. The consistency of the values of the experimental tie-lines
was determined through the Othmer-Tobias and Hands correlations.
For the extraction effectiveness of solvents, the distribution and
selectivity curves were plotted. In addition, these experimental tieline
data were also correlated with NRTL model. The interaction
parameters for the NRTL model were retrieved from the obtained
experimental results by means of a combination of the homotopy
method and the genetic algorithms.
Abstract: The present paper develops and validates a numerical procedure for the calculation of turbulent combustive flow in converging and diverging ducts and throuh simulation of the heat transfer processes, the amount of production and spread of Nox pollutant has been measured. A marching integration solution procedure employing the TDMA is used to solve the discretized equations. The turbulence model is the Prandtl Mixing Length method. Modeling the combustion process is done by the use of Arrhenius and Eddy Dissipation method. Thermal mechanism has been utilized for modeling the process of forming the nitrogen oxides. Finite difference method and Genmix numerical code are used for numerical solution of equations. Our results indicate the important influence of the limiting diverging angle of diffuser on the coefficient of recovering of pressure. Moreover, due to the intense dependence of Nox pollutant to the maximum temperature in the domain with this feature, the Nox pollutant amount is also in maximum level.
Abstract: The paper presents a one-dimensional transient
mathematical model of compressible thermal multi-component gas
mixture flows in pipes. The set of the mass, momentum and enthalpy
conservation equations for gas phase is solved. Thermo-physical
properties of multi-component gas mixture are calculated by solving
the Equation of State (EOS) model. The Soave-Redlich-Kwong
(SRK-EOS) model is chosen. Gas mixture viscosity is calculated on
the basis of the Lee-Gonzales-Eakin (LGE) correlation. Numerical
analysis on rapid decompression in conventional dry gases is
performed by using the proposed mathematical model. The model is
validated on measured values of the decompression wave speed in
dry natural gas mixtures. All predictions show excellent agreement
with the experimental data at high and low pressure. The presented
model predicts the decompression in dry natural gas mixtures much
better than GASDECOM and OLGA codes, which are the most
frequently-used codes in oil and gas pipeline transport service.
Abstract: The paper deals with the analysis of triggering
conditions and evolution processes of piping phenomena, in relation
to both mechanical and hydraulic aspects. In particular, the aim of
the study is to predict slope instabilities triggered by piping,
analysing the conditions necessary for a flow failure to occur. Really,
the mechanical effect involved in the loads redistribution around the
pipe is coupled to the drainage process arising from higher
permeability of the pipe. If after the pipe formation, the drainage
goes prevented for pipe clogging, the porewater pressure increase can
lead to the failure or even the liquefaction, with a subsequent flow
slide. To simulate the piping evolution and to verify relevant stability
conditions, a iterative coupled modelling approach has been pointed
out. As example, the proposed tool has been applied to the Stava
Valley disaster (July, 1985), demonstrating that piping might be one
of triggering phenomena of the tailings dams collapse.
Abstract: Noise has adverse effect on human health and
comfort. Noise not only cause hearing impairment, but it also acts as
a causal factor for stress and raising systolic pressure. Additionally it
can be a causal factor in work accidents, both by marking hazards
and warning signals and by impeding concentration. Industry
workers also suffer psychological and physical stress as well as
hearing loss due to industrial noise. This paper proposes an approach
to enable engineers to point out quantitatively the noisiest source for
modification, while multiple machines are operating simultaneously.
The model with the point source and spherical radiation in a free field
was adopted to formulate the problem. The procedure works very
well in ideal cases (point source and free field). However, most of the
industrial noise problems are complicated by the fact that the noise is
confined in a room. Reflections from the walls, floor, ceiling, and
equipment in a room create a reverberant sound field that alters the
sound wave characteristics from those for the free field. So the model
was validated for relatively low absorption room at NIT Kurukshetra
Central Workshop. The results of validation pointed out that the
estimated sound power of noise sources under simultaneous
conditions were on lower side, within the error limits 3.56 - 6.35 %.
Thus suggesting the use of this methodology for practical
implementation in industry. To demonstrate the application of the
above analytical procedure for estimating the sound power of noise
sources under simultaneous operating conditions, a manufacturing
facility (Railway Workshop at Yamunanagar, India) having five
sound sources (machines) on its workshop floor is considered in this
study. The findings of the case study had identified the two most
effective candidates (noise sources) for noise control in the Railway
Workshop Yamunanagar, India. The study suggests that the
modification in the design and/or replacement of these two identified
noisiest sources (machine) would be necessary so as to achieve an
effective reduction in noise levels. Further, the estimated data allows
engineers to better understand the noise situations of the workplace
and to revise the map when changes occur in noise level due to a
workplace re-layout.
Abstract: In the paper the study of synthetic transmit aperture
method applying the Golay coded transmission for medical
ultrasound imaging is presented. Longer coded excitation allows to
increase the total energy of the transmitted signal without increasing
the peak pressure. Moreover signal-to-noise ratio and penetration
depth are improved while maintaining high ultrasound image
resolution. In the work the 128-element linear transducer array with
0.3 mm inter-element spacing excited by one cycle and the 8 and 16-
bit Golay coded sequences at nominal frequency 4 MHz was used. To
generate a spherical wave covering the full image region a single
element transmission aperture was used and all the elements received
the echo signals. The comparison of 2D ultrasound images of the
tissue mimicking phantom and in vitro measurements of the beef liver
is presented to illustrate the benefits of the coded transmission. The
results were obtained using the synthetic aperture algorithm with
transmit and receive signals correction based on a single element
directivity function.
Abstract: This paper describes a one-dimensional numerical model for natural gas production from the dissociation of methane hydrate in hydrate-capped gas reservoir under depressurization and thermal stimulation. Some of the hydrate reservoirs discovered are overlying a free-gas layer, known as hydrate-capped gas reservoirs. These reservoirs are thought to be easiest and probably the first type of hydrate reservoirs to be produced. The mathematical equations that can be described this type of reservoir include mass balance, heat balance and kinetics of hydrate decomposition. These non-linear partial differential equations are solved using finite-difference fully implicit scheme. In the model, the effect of convection and conduction heat transfer, variation change of formation porosity, the effect of using different equations of state such as PR and ER and steam or hot water injection are considered. In addition distributions of pressure, temperature, saturation of gas, hydrate and water in the reservoir are evaluated. It is shown that the gas production rate is a sensitive function of well pressure.
Abstract: In this paper, mathematical modeling of detonation in the ground is studied. Estimation of flow parameters such as velocity, maximum velocity, acceleration, maximum acceleration, shock pressure as a result of an explosion in the ground have been computed in an appropriate dynamic model approach. The variation of these parameters with the diameter of detonation place (L), density of earth or stone (¤ü), time decay of detonation (T), peak pressure (Pm), and time (t) have been analyzed. The model has been developed from the concept of underwater explosions [Refs. [1]-[3]] with appropriate changes to the present model requirements.
Abstract: The quest for alternatefuels for a CI engine has
become all the more imperative considering its importance in the
economy of a nation and from the standpoint of preserving the environment. Reported in this paper are the combustion performance and P-θ characteristics of a CI engine operating on B20 biodiesel fuel derived from Jatropha oil.Itis observed that the twin effect of advancing the injection timing and increasing the injector opening pressure (IOP) up to 220 barhas resulted in minimum brake specific
energy consumption and higherpeak pressure. It is also observed that
the crank angle of occurrence of peak pressure progressestowards top
dead center (TDC) as the timing is advanced and IOP is increased.
Abstract: In this study, the effect of nanofluids on the pool film
boiling was experimentally investigated at saturated condition under
atmospheric pressure. For this purpose, four different water-based
nanofluids (Al2O3, SiO2, TiO2 and CuO) with 0.1% particle volume
fraction were prepared. To investigate the boiling heat transfer, a
cylindrical rod with high temperature was used. The rod heated up to
high temperatures was immersed into nanofluids. The center
temperature of rod during the cooling process was recorded by using
a K-type thermocouple. The quenching curves showed that the pool
boiling heat transfer was strongly dependent on the nanoparticle
materials. During the repetitive quenching tests, the cooling time
decreased and thus, the film boiling vanished. Consequently, the
primary reason of this was the change of the surface characteristics
due to the nanoparticles deposition on the rod-s surface.
Abstract: This research details a Computational Fluid Dynamics (CFD) approach to model fluid flow in a journal bearing with 8 equispaced semi-circular axial grooves. Water is used as the lubricant and is fed from one end of the bearing to the other, under pressure. The geometry of the bearing is modeled using a commercially available modeling software GAMBIT and the flow analysis is performed using a dedicated CFD analysis software FLUENT. The pressure distribution in the bearing clearance is obtained from FLUENT for various whirl ratios and is used to calculate the hydrodynamic force components in the radial and tangential direction of the bearing. These values along with the various whirl speeds can be used to do a regression analysis to determine the stiffness and damping coefficients. The values obtained are then compared with the stiffness and damping coefficients of a 3 Axial groove water lubricated journal bearing and those obtained from a FORTRAN code for a similar bearing.
Abstract: The operating control parameters of injection
flushing type of electrical discharge machining process on stainless
steel 304 workpiece using copper tools are being optimized
according to its individual machining characteristic i.e. Electrode
Wear Ratio (EWR). Higher EWR would give bad dimensional
precision for the EDM machined workpiece because of high
electrode wear. Hence, the quality characteristic for EWR is set to
lower-the-better to achieve the optimum dimensional precision for
the machined workpiece. Taguchi method has been used for the
construction, layout and analysis of the experiment for EWR
machining characteristic. The use of Taguchi method in the
experiment saves a lot of time and cost of preparing and machining
the experiment samples. Therefore, an L18 Orthogonal array
which was the fundamental component in the statistical design of
experiments has been used to plan the experiments and Analysis of
Variance (ANOVA) is used to determine the optimum machining
parameters for this machining characteristic. The control
parameters selected for this optimization experiments are polarity,
pulse on duration, discharge current, discharge voltage, machining
depth, machining diameter and dielectric liquid pressure. The
result had shown that negative polarity machining parameter
setting will decreases EWR.
Abstract: Supercritical carbon dioxide (SC-CO2) was used as a
solvent to extract oil from wheat bran. Extractions were carried out in a
semi-batch process at temperatures ranging from 40 to 60ºC and
pressures ranging from 10 to 30 MPa, with a carbon dioxide (CO2)
flow rate of 26.81 g/min. The oil obtained from wheat bran at different
extraction conditions was quantitatively measured to investigate the
solubility of oil in SC-CO2. The solubility of wheat bran oil was found
to be enhanced in high temperature and pressure. The composition of
fatty acids in wheat bran oil was measured by gas chromatography
(GC). Linoleic, palmitic, oleic and γ-linolenic acid were the major
fatty acids of wheat bran oil. Tocopherol contents in oil were analyzed
by high performance liquid chromatography (HPLC). The highest
amount of phenolics and tocopherols (α and β) were found at
temperature of 60ºC and pressure of 30 MPa.
Abstract: In this study, an experimental investigation was carried
out to fix CO2 into the electronic arc furnace (EAF) reducing slag from
stainless steelmaking process under wet grinding. The slag was ground
by the vibrating ball mill with the CO2 and pure water. The reaction
behavior was monitored with constant pressure method, and the
change of CO2 volume in the experimental system with grinding time
was measured. It was found that the CO2 absorption occurred as soon
as the grinding started. The CO2 absorption under wet grinding was
significantly larger than that under dry grinding. Generally, the
amount of CO2 absorption increased as the amount of water, the
amount of slag, the diameter of alumina ball and the initial pressure of
CO2 increased. However, the initial absorption rate was scarcely
influenced by the experimental conditions except for the initial CO2
pressure. According to this research, the CO2 reacted with the CaO
inside the slag to form CaCO3.
Abstract: The rate of production of main products of the Fischer-Tropsch reactions over Fe/HZSM5 bifunctional catalyst in a fixed bed reactor is investigated at a broad range of temperature, pressure, space velocity, H2/CO feed molar ratio and CO2, CH4 and water flow rates. Model discrimination and parameter estimation were performed according to the integral method of kinetic analysis. Due to lack of mechanism development for Fisher – Tropsch Synthesis on bifunctional catalysts, 26 different models were tested and the best model is selected. Comprehensive one and two dimensional heterogeneous reactor models are developed to simulate the performance of fixed-bed Fischer – Tropsch reactors. To reduce computational time for optimization purposes, an Artificial Feed Forward Neural Network (AFFNN) has been used to describe intra particle mass and heat transfer diffusion in the catalyst pellet. It is seen that products' reaction rates have direct relation with H2 partial pressure and reverse relation with CO partial pressure. The results show that the hybrid model has good agreement with rigorous mechanistic model, favoring that the hybrid model is about 25-30 times faster.
Abstract: In this study, mechanically alloyed Al 2024 powder is
densified by conventional sintering and by equal channel angular
pressing (ECAP) with and without back pressure. The powder was
encapsulated in an aluminium can for consolidation through ECAP.
The properties obtained in the compacts by conventional sintering
route and by ECAP are compared. The effect of conventional
sintering and ECAP on consolidation behaviour of powder,
microstructure, density and hardness is discussed. Room temperature
back pressure aided ECAP results in nearly full denser (97% of its
theoretical density) compact at room temperature. NanoIndentation
technique was used to determine the modulus of the consolidated
compacts.