Abstract: In the recent years, a considerable level of interest has been developed on the use of earth in construction, led by its rediscovery as an environmentally building material. The Stabilized Earth Concrete (SEC) is a good alternative to the cement concrete, thanks to its thermal and moisture regulating features. Many parameters affect the behavior of stabilized earth concrete. This article presents research results related to the influence of the compacting nature on some SEC properties namely: The mechanical behavior, capillary absorption, shrinkage and sustainability to water erosion, and this, basing on two types of compacting: Manual and semi-automatic.
Abstract: Topology optimization technique utilizes constant
element densities as design parameters. Finally, optimal distribution
contours of the material densities between voids (0) and solids (1) in
design domain represent the determination of topology. It means that
regions with element density values become occupied by solids in
design domain, while there are only void phases in regions where no
density values exist. Therefore the void regions of topology
optimization results provide design information to decide appropriate
depositions of web-opening in structure. Contrary to the basic
objective of the topology optimization technique which is to obtain
optimal topology of structures, this present study proposes a new idea
that topology optimization results can be also utilized for decision of
proper web-opening’s position. Numerical examples of linear
elastostatic structures demonstrate efficiency of methodological
design processes using topology optimization in order to determinate
the proper deposition of web-openings.
Abstract: In recent years, non-invasive Focused Ultrasound (FU) has been utilized for generating bubbles (cavities) to ablate target tissue by mechanical fractionation. Intensities >10 kW/cm2 are required to generate the inertial cavities. The generation, rapid growth, and collapse of these inertial cavities cause tissue fractionation and the process is called Histotripsy. The ability to fractionate tissue from outside the body has many clinical applications including the destruction of the tumor mass. The process of tissue fractionation leaves a void at the treated site, where all the affected tissue is liquefied to particles at sub-micron size. The liquefied tissue will eventually be absorbed by the body. Histotripsy is a promising non-invasive treatment modality. This paper presents a technique for generating inertial cavities at lower intensities (< 1 kW/cm2). The technique (patent pending) is based on amplitude modulation (AM), whereby a low frequency signal modulates the amplitude of a higher frequency FU wave. Cavitation threshold is lower at low frequencies; the intensity required to generate cavitation in water at 10 kHz is two orders of magnitude lower than the intensity at 1 MHz. The Amplitude Modulation technique can operate in both continuous wave (CW) and pulse wave (PW) modes, and the percentage modulation (modulation index) can be varied from 0 % (thermal effect) to 100 % (cavitation effect), thus allowing a range of ablating effects from Hyperthermia to Histotripsy. Furthermore, changing the frequency of the modulating signal allows controlling the size of the generated cavities. Results from in vitro work demonstrate the efficacy of the new technique in fractionating soft tissue and solid calcium carbonate (Chalk) material. The technique, when combined with MR or Ultrasound imaging, will present a precise treatment modality for ablating diseased tissue without affecting the surrounding healthy tissue.
Abstract: This study examined the structural reliability of the Nigerian grown Opepe timber as bridge beam material. The strength of a particular specie of timber depends so much on some factors such as soil and environment in which it is grown. The steps involved are collection of the Opepe timber samples, seasoning/preparation of the test specimens, determination of the strength properties/statistical analysis, development of a computer programme in FORTRAN language and finally structural reliability analysis using FORM 5 software. The result revealed that the Nigerian grown Opepe is a reliable and durable structural bridge beam material for span of 5000mm, depth of 400mm, breadth of 250mm and end bearing length of 150mm. The probabilities of failure in bending parallel to the grain, compression perpendicular to the grain, shear parallel to the grain and deflection are 1.61 x 10-7, 1.43 x 10-8, 1.93 x 10-4 and 1.51 x 10-15 respectively. The paper recommends establishment of Opepe plantation in various Local Government Areas in Nigeria for structural applications such as in bridges, railway sleepers, generation of income to the nation as well as creating employment for the numerous unemployed youths.
Abstract: Polymers from renewable resources have attracted an increasing amount of attention over the last two decades, predominantly due to two major reasons: firstly environmental concerns, and secondly the realization that our petroleum resources are finite. Finding new uses for agricultural commodities is also an important area of research. Therefore, it is crucial to get new sources of natural materials that can be used in different applications. Ramon tree (Brosimum alicastrum) is a tropical plant that grows freely in Yucatan countryside. This paper focuses on the seeds recollection, processing and starch extraction and characterization in order to find out about its suitability as biomaterial. Results demonstrated that it has a high content of qualities to be used not only as comestible but also as an important component in polymeric blends.
Abstract: Effective treatment of ground instability is essential when managing the impacts associated with historic mining. A field trial was undertaken by the Coal Authority to investigate the geotechnical performance and potential use of composite materials comprising resin and fill or stone to safely treat surface collapses, such as crown-holes, associated with shallow mining. Test pits were loosely filled with various granular fill materials. The fill material was injected with commercially available silicate and polyurethane resin foam products. In situ and laboratory testing was undertaken to assess the geotechnical properties of the resultant composite materials. The test pits were subsequently excavated to assess resin permeation. Drilling and resin injection was easiest through clean limestone fill materials. Recycled building waste fill material proved difficult to inject with resin; this material is thus considered unsuitable for use in resin composites. Incomplete resin permeation in several of the test pits created irregular ‘blocks’ of composite. Injected resin foams significantly improve the stiffness and resistance (strength) of the un-compacted fill material. The stiffness of the treated fill material appears to be a function of the stone particle size, its associated compaction characteristics (under loose tipping) and the proportion of resin foam matrix. The type of fill material is more critical than the type of resin to the geotechnical properties of the composite materials. Resin composites can effectively support typical design imposed loads. Compared to other traditional treatment options, such as cement grouting, the use of resin composites is potentially less disruptive, particularly for sites with limited access, and thus likely to achieve significant reinstatement cost savings. The use of resin composites is considered a suitable option for the future treatment of shallow mining collapses.
Abstract: The new methods as accelerated steam distillation
assisted by microwave (ASDAM) is a combination of microwave
heating and steam distillation, performed at atmospheric pressure at
very short extraction time. Isolation and concentration of volatile
compounds are performed by a single stage. (ASDAM) has been
compared with (ASDAM) with cryogrinding of seeds (CG) and a
conventional technique, hydrodistillation assisted by microwave
(HDAM), hydro-distillation (HD) for the extraction of essential oil
from aromatic herb as caraway and cumin seeds. The essential oils
extracted by (ASDAM) for 1 min were quantitatively (yield) and
qualitatively (aromatic profile) no similar to those obtained by
ASDAM-CG (1 min) and HD (for 3 h). The accelerated microwave
extraction with cryogrinding inhibits numerous enzymatic reactions
as hydrolysis of oils.
Microwave radiations constitute the adequate mean for the
extraction operations from the yields and high content in major
component majority point view, and allow to minimise considerably
the energy consumption, but especially heating time too, which is one
of essential parameters of artifacts formation.
The ASDAM and ASDAM-CG are green techniques and yields an
essential oil with higher amounts of more valuable oxygenated
compounds comparable to the biosynthesis compounds, and allows
substantial savings of costs, in terms of time, energy and plant
material.
Abstract: This study investigated the differences in the objective parameters of sound depending on the changes in the lengths of the lateral surfaces of a space and on the replacement of the sound absorbers that are placed on these surfaces. To this end, three models of room were chosen. The widths and heights of these rooms were the same but the lengths of the rooms were changed. The smallest room was 8 m. wide and 10 m. long. The lengths of the other two rooms were 15 m. and 20 m. For each model, the differences in the objective parameters of sound were determined by keeping all the material in the space intact and by changing only the positions of the sound absorbers that were placed on the walls. The sound absorbers that were used on the walls were of two different sizes. The sound absorbers that were placed on the walls were 4 m and 8 m. long and story-height (3 m.). In all model room types, the sound absorbers were placed on the long walls in three different ways: at the end of the long walls where the long walls meet the front wall; at the end of the long walls where the long walls meet the back wall; and in the middle part of the long walls. Except for the specially placed sound absorbers, the ground, wall and ceiling surfaces were covered with three different materials. There were no constructional elements such as doors and windows on the walls. On the surfaces, the materials specified in the Odeon 10 material library were used as coating material. Linoleum was used as flooring material, painted plaster as wall coating material and gypsum boards as ceiling covering (2 layers with a total of 32 mm. thickness). These were preferred due to the fact that they are the commonly used materials for these purposes. This study investigated the differences in the objective parameters of sound depending on the changes in the lengths of the lateral surfaces of a space and on the replacement of the sound absorbers that are placed on these surfaces. To this end, three models of room were chosen. The widths and heights of these rooms were the same but the lengths of the rooms were changed. The smallest room was 8 m. wide and 10 m. long. The lengths of the other two rooms were 15 m. and 20 m. For each model, the differences in the objective parameters of sound were determined by keeping all the material in the space intact and by changing only the positions of the sound absorbers that were placed on the walls. The sound absorbers that were used on the walls were of two different sizes. The sound absorbers that were placed on the walls were 4 m and 8 m. long and story-height (3 m.). In all model room types, the sound absorbers were placed on the long walls in three different ways: at the end of the long walls where the long walls meet the front wall; at the end of the long walls where the long walls meet the back wall; and in the middle part of the long walls. Except for the specially placed sound absorbers, the ground, wall and ceiling surfaces were covered with three different materials. There were no constructional elements such as doors and windows on the walls. On the surfaces, the materials specified in the Odeon 10 material library were used as coating material. Linoleum was used as flooring material, painted plaster as wall coating material and gypsum boards as ceiling covering (2 layers with a total of 32 mm. thickness). These were preferred due to the fact that they are the commonly used materials for these purposes.
Abstract: Reinforced cement concrete is getting extensively used
for construction of different type of structures for the last one century.
During this period, we have constructed many structures like
buildings, bridges, industrial structures, pavement, water tanks etc.
using this construction material. These structures have been created
with huge investment of resources. It is essential to maintain those
structures in functional condition. Since deterioration in RCC
Structures is a common and natural phenomenon it is required to have
a detailed plan, methodology for structural repair and rehabilitation
shall be in place for dealing such issues. It is important to know exact
reason of distress, type of distress and correct method of repair
concrete structures. The different methods of repair are described in
paper according to distress category which can be refereed for repair.
Major finding of the study is that to protect our structure we need to
have maintenance frequency and correct material to be chosen for
repair. Also workmanship during repair needs to be taken utmost care
for quality repair.
Abstract: The present paper examines the impact noise
transmission through some floor building assemblies. The Acoubat
software numerical simulation has been used to simulate the impact
noise transmission through different floor configurations used in
Algerian construction mode. The results are compared with the
available measurements. We have developed two experimental
methods, i) field method, and ii) laboratory method using Brüel and
Kjær equipments. The results show that the different cases of floor
configurations need some improvement to ensure the acoustic
comfort in the receiving apartment. The recommended value of the
impact sound level in the receiving room should not exceed 58 dB.
The important results obtained in this paper can be used as platform
to improve the Algerian building acoustic regulation aimed at the
construction of the multi-storey residential building.
Abstract: In India, most of the pavement is laid by bituminous
road and the consumption of binder is high for pavement construction
and also modified binders are used to satisfy any specific pavement
requirement. Since the binders are visco-elastic material which is
having the mechanical properties of binder transition from viscoelastic
solid to visco-elastic fluid. In this paper, two different
protocols were used to measure the viscosity property of binder using
a Brookfield Viscometer and there is a need to find the appropriate
mixing and compaction temperatures of various types of binders
which can result in complete aggregate coating and adequate field
density of HMA mixtures. The aim of this work is to find the
transition temperature from Non-Newtonian behavior to Newtonian
behavior of the binder by adopting a steady shear protocol and the
shear rate ramp protocol. The transition from non-Newtonian to
Newtonian can occur through an increase of temperature and shear of
the material. The test has been conducted for unmodified binder VG
30. The transition temperature was found in the unmodified binder
VG is 120oC. Therefore, the application of both modified binder and
unmodified binder in the pavement construction needs to be studied
properly by considering temperature and traffic loading factors of the
respective project site.
Abstract: In the present work, forming limit diagrams and strain
distribution profile diagrams for extra deep drawing steel at room and
elevated temperatures have been determined experimentally by
conducting stretch forming experiments by using designed and
fabricated warm stretchforming tooling setup. With the help of
forming Limit Diagrams (FLDs) and strain, distribution profile
diagrams the formability of Extra Deep Drawing steel has been
analyzed and co-related with mechanical properties like strain
hardening COEFFICIENT (n) and normal anisotropy (r−). Mechanical
properties of EDD steel from room temperature to 4500C were
determined and discussed the impact of temperature on the properties
like work hardening exponent (n) anisotropy (r-) and strength
coefficient of the material. In addition, the fractured surfaces after
stretching have undergone the some metallurgical investigations and
attempt has been made to co-relate with the formability of EDD steel
sheets. They are co-related and good agreement with FLDs at various
temperatures.
Abstract: This paper presents numerical analysis in terms of
buckling resistance of GFRP sandwich infill panels system under the
influence of increased temperature on the foam core. Failure mode
under in-plane compression is studied by means of numerical analysis
with ABAQUS platform. Parameters considered in this study are
contact length and both the type of foam for core and the variation of
its module elastic under the thermal influence. Increment of
temperature is considered in static cases and only applied to core.
Indeed, it is proven that the effect of temperature alters the mechanical
properties of the entire panel system. Moreover, the rises of
temperature result in a decrease in strength of the panel. This is due to
the polymeric nature of this material. Additionally, the contact length
also displays the effect on performance of infill panel. Their
significance factors are based on type of polymer for core. Therefore,
by comparing difference type of core material, the variation can be
reducing.
Abstract: Rapid prototyping is a new group of manufacturing
processes, which allows fabrication of physical of any complexity
using a layer by layer deposition technique directly from a computer
system. The rapid prototyping process greatly reduces the time and
cost necessary to bring a new product to market. The prototypes
made by these systems are used in a range of industrial application
including design evaluation, verification, testing, and as patterns for
casting processes. These processes employ a variety of materials and
mechanisms to build up the layers to build the part. The present work
was to build a FDM prototyping machine that could control the X-Y
motion and material deposition, to generate two-dimensional and
three-dimensional complex shapes. This study focused on the
deposition of wax material. This work was to find out the properties
of the wax materials used in this work in order to enable better
control of the FDM process. This study will look at the integration of
a computer controlled electro-mechanical system with the traditional
FDM additive prototyping process. The characteristics of the wax
were also analysed in order to optimise the model production process.
These included wax phase change temperature, wax viscosity and
wax droplet shape during processing.
Abstract: The study investigated efficiency cassava peel carbon
and Zinc Chloride activated cassava peel carbon at 1:3, 2:3 and 1:1
activation levels in the removal of nitrates from oxidized cassava
processing wastewater. Results showed that the CPC and CPAC were
effective in adsorption of nitrates. A summary of results from the
study revealed that CPAC at 1:3 exhibited the highest initial
decontamination (69.5% after 2 hrs) while CPAC at 1:1 activation
ratio showed a slower initial decontamination rate. The CPC &
CPAC exhibited Langmuir Rα values of 0.15, 0.11, 0.09, and 0.07 for
the 0:1, 1:3, 2:3 and 1:1 confirming its suitability as adsorption
material.
Abstract: Zinc borate is an important inorganic hydrate borate
material, which can be used as a flame retardant agent and corrosion
resistance material. This compound can loss its structural water
content at higher than 290°C. Due to thermal stability; Zinc Borate
can be used as flame retardant at high temperature process of plastic
and gum. In this study, the ultrasonic reaction of zinc borates were
studied using hydrozincite (Zn5(CO3)2·(OH)6) and boric acid
(H3BO3) raw materials. Before the synthesis raw materials were
characterized by X-Ray Diffraction (XRD) and Fourier Transform
Infrared Spectroscopy (FT-IR). Ultrasonic method is a new
application on the zinc borate synthesis. The synthesis parameters
were set to 90°C reaction temperature and 55 minutes of reaction
time, with 1:1, 1:2, 1:3, 1:4 and 1:5 molar ratio of starting materials
(Zn5(CO3)2·(OH)6 : H3BO3). After the zinc borate synthesis, the
products were analyzed by XRD and FT-IR. As a result, optimum
molar ratio of 1:5 is determined for the synthesis of zinc borates with
ultrasonic method.
Abstract: Rice Husk (RH) is the major byproduct in the
processing of paddy rice. The management of this waste has become
a big challenge to some of the rice producers, some of these wastes
are left in open dumps while some are burn in the open space, and
these two actions have been contributing to environmental pollution.
This study evaluates an alternative waste management of this
agricultural product for use as a civil engineering material. The RH
was burn in a controlled environment to form Rice Husk Ash (RHA).
The RHA was mix with lateritic clay at 0, 2, 4, 6, 8, and 10%
proportion by weight. Chemical test was conducted on the open burn
and controlled burn RHA with the lateritic clay. Physical test such as
particle size distribution, Atterberg limits test, and density test were
carried out on the mix material. The chemical composition obtained
for the RHA showed that the total percentage compositions of Fe2O3,
SiO2 and Al2O3 were found to be above 70% (class “F” pozzolan)
which qualifies it as a very good pozzolan. The coefficient of
uniformity (Cu) was 8 and coefficient of curvature (Cc) was 2 for the
soil sample. The Plasticity Index (PI) for the 0, 2, 4, 6, 8. 10% was
21.0, 18.8, 16.7, 14.4, 12.4 and 10.7 respectively. The work
concluded that RHA can be effectively used in hydraulic barriers and
as a stabilizing agent in soil stabilization.
Abstract: This paper presents the results of a Finite Element
based vibration analysis of a solar powered Unmanned Aerial
Vehicle (UAV). The purpose of this paper was to quantify the free
vibration, forced vibration response due to differing point inputs in
order to predict the relative response magnitudes and frequencies at
various wing locations of vibration induced power generators
(magnet in coil) excited by gust and/or control surface pulse-decays
used to help power the flight of the electric UAV. A Fluid Structure
Interaction (FSI) study was performed in order to ascertain pertinent
design stresses and deflections as well as aerodynamic parameters of
the UAV airfoil. The 10 ft span airfoil is modeled using Mylar as the
primary material. Results show that the free mode in bending is 4.8
Hz while the first forced bending mode is on range of 16.2 to 16.7 Hz
depending on the location of excitation. The free torsional bending
mode is 28.3 Hz, and the first forced torsional mode is range of 26.4
to 27.8 Hz, depending on the location of excitation. The FSI results
predict the coefficients of aerodynamic drag and lift of 0.0052 and
0.077, respectively, which matches hand-calculations used to validate
the Finite Element based results. FSI based maximum von Mises
stresses and deflections were found to be 0.282 MPa and 3.4 mm,
respectively. Dynamic pressures on the airfoil range from 1.04 to
1.23 kPa corresponding to velocity magnitudes in range of 22 to 66
m/s.
Abstract: Erosion and abrasion are wear mechanisms reducing
the lifetime of machine elements like valves, pump and pipe systems.
Both wear mechanisms are acting at the same time, causing a
“Synergy” effect, which leads to a rapid damage of the surface.
Different parameters are effective on erosive abrasive wear rate. In
this study effect of particle impact angle on wear rate and wear
mechanism of ductile and brittle materials was investigated. A new
slurry pot was designed for experimental investigation. As abrasive
particle, silica sand was used. Particle size was ranking between 200-
500 μm. All tests were carried out in a sand-water mixture of 20%
concentration for four hours. Impact velocities of the particles were
4.76 m/s. As ductile material steel St 37 with Vickers Hardness
Number (VHN) of 245 and quenched St 37 with 510 VHN was used
as brittle material. After wear tests, morphology of the eroded
surfaces were investigated for better understanding of the wear
mechanisms acting at different impact angles by using Scanning
Electron Microscope. The results indicated that wear rate of ductile
material was higher than brittle material. Maximum wear rate was
observed by ductile material at a particle impact angle of 300 and
decreased further by an increase in attack angle. Maximum wear rate
by brittle materials was by impact angle of 450 and decreased further
up to 900. Ploughing was the dominant wear mechanism by ductile
material. Microcracks on the surface were detected by ductile
materials, which are nucleation centers for crater formation. Number
of craters decreased and depth of craters increased by ductile
materials by attack angle higher than 300. Deformation wear
mechanism was observed by brittle materials. Number and depth of
pits decreased by brittle materials by impact angles higher than 450.
At the end it is concluded that wear rate could not be directly related
to impact angle of particles due to the different reaction of ductile and
brittle materials.
Abstract: This study aims at developing a novel cold asphalt
concrete binder course mixture by using Ordinary Portland Cement
(OPC) as a replacement for conventional mineral filler (0%-100%)
with new by-product material (LJMU-A2) used as a supplementary
cementitious material. With this purpose, cold asphalt concrete binder
course mixtures with cationic emulsions were studied by means of
stiffness modulus whereas water sensitivity was assessed by
measuring the stiffness modulus ratio before and after sample
conditioning.
The results indicate that a substantial enhancement in the stiffness
modulus and a considerable improvement of water sensitivity
resistance is achieved by adding LJMU-A2 to the cold asphalt
mixtures as a supplementary cementitious material. Moreover, the
addition of LJMU-A2 to those mixtures leads to a stiffness modulus
after 2-day curing compared to that obtained with Portland cement,
which occurs after 7-day curing.