Abstract: The development of solutions to improve the resistance of buildings to short-term dynamic loads, particularly impact load, is driven by the urgent demand worldwide on securing human life and critical infrastructures. The research training group GRK 2250/1 aims to develop mineral-bonded composites that allow the fabrication of thin-layered strengthening layers providing available concrete members with enhanced impact resistance. This paper presents the development of 3D woven wire cellular structures that can be used as innovative reinforcement for targeted composites. 3D woven wire cellular structures are truss-like architectures that can be fabricated in an automatized process with a great customization possibility. The specific architecture allows this kind of structures to have good load bearing capability and forming behavior, which is of great potential to give strength against impact loading. An appropriate combination of topology and material enables an optimal use of thin-layered reinforcement in concrete constructions.
Abstract: The exemplary mechanical performance and durability of ultra-high performance concrete (UHPC) has led to its rapid emergence as an advanced cementitious material. The uncharacteristically high mechanical strength and ductility of UHPC makes it a promising potential material for defense structures which may be subject to highly dynamic loads like impact or blast. However, the mechanical response of UHPC under dynamic loading has not been fully characterized. In particular, there is a need to characterize the energy absorption of UHPC under high-frequency shear loading. This paper presents preliminary results from a parametric study of the dynamic shear energy absorption of UHPC using the Charpy impact test. UHPC mixtures with compressive strengths in the range of 100-150 MPa exhibited dynamic shear energy absorption in the range of 0.9-1.5 kJ/m. Energy absorption is shown to be sensitive to the water/cement ratio, silica fume content, and aggregate gradation. Energy absorption was weakly correlated to compressive strength. Results are highly sensitive to specimen preparation methods, and there is a demonstrated need for a standardized test method for high frequency shear in cementitious composites.
Abstract: One of the main purposes of designing bucklingrestrained
braces is the fact that the entire lateral load is wasted by
the braces, the entire gravitational load is moved to the foundation
through the beams, and the columns can be moved to the foundation.
In other words, braces are designed for bearing lateral load. In the
implementation of the structure, it should be noted that the
implementation of various parts of the structure must be conducted in
such a way that the buckling-restrained braces would not bear the
gravitational load. Moreover, this type of brace has been investigated
under impact loading, and the design goals of designing method
(direct motion) are controlled under impact loading. The results of
dynamic analysis are shown as the relocation charts of the floors and
switch between the floors. Finally, the results are compared with each
other.
Abstract: Carbon fiber reinforced polymersarewidely used to strengthen steel structural elements. These structural elements are normally subjected to static, dynamic and fatigue loadings during their life-time. CFRP laminate is commonly used to strengthen these structures under the subjected loads. A number of studies have focused on the characteristics of CFRP sheets bonded to steel members under static, dynamic and fatigue loadings. However, there is a gap in understanding the bonding behavior between CFRP laminates and steel members under impact loading. This paper shows the effect of high load rates on this bond. CFRP laminate CFK 150/2000 was used to strengthen steel joints using Araldite 420 epoxy. The results show that applying a high load rate significantly affects the bond strength but has little influence on the effective bond length.
Abstract: Three dimensional non-Interlaced carbon fibre
reinforced silicon carbide (3-D-Cf/SiC) composites with pyrocarbon
interphase were fabricated using isothermal chemical vapor
infiltration (ICVI) combined with polymer impregnation pyrolysis
(PIP) process. Polysilazane (PSZ) is used as a preceramic polymer to
obtain silicon carbide matrix. Thermo gravimetric analysis (TGA),
Infrared spectroscopic analysis (IR) and X-ray diffraction (XRD)
analysis were carried out on PSZ pyrolysed at different temperatures
to understand the pyrolysis and obtaining the optimum pyrolysing
condition to yield β-SiC phase. The density of the composites was
1.94 g cm-3 after the 3-D carbon preform was SiC infiltrated for 280 h
with one intermediate polysilazane pre-ceramic PIP process.
Mechanical properties of the composite materials were investigated
under tensile, flexural, shear and impact loading. The values of
tensile strength were 200 MPa at room temperature (RT) and 195
MPa at 500°C in air. The average RT flexural strength was 243 MPa.
The lower flexural strength of these composites is because of the
porosity. The fracture toughness obtained from single edge notched
beam (SENB) technique was 39 MPa.m1/2. The work of fracture
obtained from the load-displacement curve of SENB test was 22.8
kJ.m-2. The composites exhibited excellent impact resistance and the
dynamic fracture toughness of 44.8 kJ.m-2 is achieved as determined
from instrumented Charpy impact test. The shear strength of the
composite was 93 MPa, which is significantly higher compared 2-D
Cf/SiC composites. Microstructure evaluation of fracture surfaces
revealed the signatures of fracture processes and showed good
support for the higher toughness obtained.
Abstract: Each year nearly nine hundred persons die in head injuries and over fifty thousand persons are severely injured due to non wearing of helmets. In motor cycle accidents, the human head is exposed to heavy impact loading against natural protection. In this work, an attempt has been made for analyzing the helmet with all the standard data. The simulation software ‘ANSYS’ is used to analyze the helmet with different conditions such as bottom fixed-load on top surface, bottom fixed -load on top line, side fixed –load on opposite surface, side fixed-load on opposite line and dynamic analysis. The maximum force of 19.5 kN is applied on the helmet to study the model in static and dynamic conditions. The simulation has been carried out for the static condition for the parameters like total deformation, strain energy, von-Mises stress for different cases. The dynamic analysis has been performed for the parameter like total deformation and equivalent elastic strain. The result shows that these values are concentrated in the retention portion of the helmet. These results have been compared with the standard experimental data proposed by the BIS and well within the acceptable limit.
Abstract: In recent year, with recent increase of interest towards leisure sports, increased number of Zip-Line or Zip-Wire facilities has built. Many researches have been actively conducted on the emphasis of the cable and the wire at the bridge. However, very limited researches have been conducted on the safety of the Zip-Line structure. In fact, fall accidents from Zip-Line have been reported frequently. Therefore, in this study, the structural safety of Zip-Line under dynamic impact loading condition were evaluated on the previously installed steel cable for leisure (Zip-Line), using 3-dimensional nonlinear Finite Element (FE) model. The result from current study would assist assurance of systematic stability of Zip-Line.
Abstract: The complex shape of the human pelvic bone was
successfully imaged and modeled using finite element FE processing.
The bone was subjected to quasi-static and dynamic loading
conditions simulating the effect of both weight gain and impact.
Loads varying between 500 – 2500 N (~50 – 250 Kg of weight) was
used to simulate 3D quasi-static weight gain. Two different 3D
dynamic analyses, body free fall at two different heights (1 and 2 m)
and forced side impact at two different velocities (20 and 40 Km/hr)
were also studied. The computed resulted stresses were compared for
the four loading cases, where Von Misses stresses increases linearly
with the weight gain increase under quasi-static loading. For the
dynamic models, the Von Misses stress history behaviors were
studied for the affected area and effected load with respect to time.
The normalization Von Misses stresses with respect to the applied
load were used for comparing the free fall and the forced impact load
results. It was found that under the forced impact loading condition
an over lapping behavior was noticed, where as for the free fall the
normalized Von Misses stresses behavior was found to nonlinearly
different. This phenomenon was explained through the energy
dissipation concept. This study will help designers in different
specialization in defining the weakest spots for designing different
supporting systems.
Abstract: A numerical analysis of a reinforced concrete (RC) wall under missile impact loading is presented in this study. The model created by Technical Research Center of Finland was used. The commercial finite element code, LS-DYNA was used to analyze. The structural components of the reinforced concrete wall, missile and their contacts are fully modeled. The material nonlinearity with strain rate effects considering damage and failure is included in the analysis. The results of analysis were verified with other research results. The case-studies with different reinforcement ratios were conducted to investigate the influence of reinforcement on the punching behavior of walls under missile impact.
Abstract: Within this work High Temperature Single Impact
Studies were performed to evaluate deformation mechanisms at
different energy and momentum levels. To show the influence of
different microstructures and hardness levels and their response to
single impacts four different materials were tested at various
temperatures up to 700°C. One carbide reinforced NiCrBSi based
Metal Matrix Composite and three different steels were tested. The
aim of this work is to determine critical energies for fracture
appearance and the materials response at different energy and
momenta levels. Critical impact loadings were examined at elevated
temperatures to limit operating conditions in impact dominated
regimes at elevated temperatures. The investigations on the
mechanisms were performed using different means of microscopy at
the surface and in metallographic cross sections. Results indicate
temperature dependence of the occurrence of cracks in hardphase
rich materials, such as Metal Matrix Composites High Speed Steels
and the influence of different impact momenta at constant energies
on the deformation of different steels.
Abstract: The commercial finite element program LS-DYNA was employed to evaluate the response and energy absorbing capacity of cylindrical metal tubes that are externally wrapped with composite. The effects of composite wall thickness, loading conditions and fiber ply orientation were examined. The results demonstrate that a wrapped composite can be utilized effectively to enhance the crushing characteristics and energy absorbing capacity of the tubes. Increasing the thickness of the composite increases the mean force and the specific energy absorption under both static and dynamic crushing. The ply pattern affects the energy absorption capacity and the failure mode of the metal tube and the composite material property is also significant in determining energy absorption efficiency.