Abstract: Hydrogels are three-dimensional, hydrophilic,
polymeric networks composed of homopolymers or copolymers and
are insoluble in water due to the presence of chemical or physical
cross-links. When hydrogels come in contact with aqueous solutions,
they can effectively sorb and retain the dissolved substances,
depending on the nature of the monomeric units comprising the
hydrogel. For this reason, hydrogels have been proposed in several
studies as water purification agents. At the present work anionic
hydrogels bearing negatively charged –COO- groups were prepared
and investigated. These gels are based on sodium acrylate (ANa),
either homopolymerized (poly(sodiumacrylate), PANa) or
copolymerized (P(DMAM-co-ANa)) with N,N Dimethylacrylamide
(DMAM). The hydrogels were used to extract some model organic
dyes from water. It is found that cationic dyes are strongly sorbed and
retained by the hydrogels, while sorption of anionic dyes was
negligible. In all cases it was found that both maximum sorption
capacity and equilibrium binding constant varied from one dye to the
other depending on the chemical structure of the dye, the presence of
functional chemical groups and the hydrophobic-hydrophilic balance.
Finally, the nonionic hydrogel of the homopolymer poly(N,Ndimethylacrylamide),
PDMAM, was also used for reasons of
comparison.
Abstract: Polylactic acid (PLA) is the most commercially
available bio-based and biodegradable plastic at present. PLA has
been used in plastic related industries including single-used
containers, disposable and environmentally friendly packaging owing
to its renewability, compostability, biodegradability, and safety.
Although PLA demonstrates reasonably good optical, physical,
mechanical and barrier properties comparable to the existing
petroleum-based plastics, its brittleness and mold shrinkage as well as
its price are the points to be concerned for the production of rigid and
semi-rigid packaging. Blending PLA with other bio-based polymers
including thermoplastic starch (TPS) is an alternative not only to
achieve a complete bio-based plastic, but also to reduce the
brittleness, shrinkage during molding and production cost of the
PLA-based products. TPS is a material produced mainly from starch
which is cheap, renewable, biodegradable, compostable, and nontoxic.
It is commonly prepared by a plasticization of starch under
applying heat and shear force. Although glycerol has been reported as
one of the most plasticizers used for preparing TPS, its migration
caused the surface stickiness of the TPS products. In some cases,
mixed plasticizers or natural fibers have been applied to impede the
retrogradation of starch or reduce the migration of glycerol. The
introduction of fibers into TPS-based materials could reinforce the
polymer matrix as well. Therefore, the objective of the present
research is to study the effect of starch type (i.e. native starch and
phosphate starch), plasticizer type (i.e. glycerol and xylitol with a
weight ratio of glycerol to xylitol of 100:0, 75:25, 50:50, 25:75 and
0:100) and fiber content (i.e. in the range of 1-25 %wt) on properties
of PLA/TPS blend and composite. PLA/TPS blends and composites
were prepared using a twin-screw extruder and then converted into
dumbbell-shaped specimens using an injection molding machine. The
PLA/TPS blends prepared by using phosphate starch showed higher
tensile strength and stiffness than the blends prepared by using native
one. In contrast, the blends from native starch exhibited higher
extensibility and heat distortion temperature (HDT) than those from
the modified starch. Increasing xylitol content resulted in enhanced
tensile strength, stiffness and water resistance, but decreased
extensibility and HDT of the PLA/TPS blend. Tensile properties and
hydrophobicity of the blend could be improved by incorporating
silane treated-jute fibers.
Abstract: This paper presents the influences on the entrainment
of serpentines by grinding and reagents during copper–nickel sulfide
flotation. The previous bench flotation tests were performed to extract
the metallic values from the ore in Yunnan Mine, China and the
relatively satisfied results with recoveries of 86.92% Cu, 54.92% Ni,
and 74.73% Pt+Pd in the concentrate were harvested at their grades of
4.02%, 3.24% and 76.61 g/t, respectively. However, the content of
MgO in the concentrate was still more than 19%. Micro-flotation tests
were conducted with the objective of figuring out the influences on the
entrainment of serpentines into the concentrate by particle size,
flocculants or depressants and collectors, as well as visual
observations in suspension by OLYMPUS camera. All the tests results
pointed to the presences of both “entrapped-in” serpentines and its
coating on the hydrophobic flocs resulted from strong collectors
(combination of butyl xanthate, butyl ammonium dithophosphate,
even after adding carboxymethyl cellulose as effective depressant.
And fine grinding may escalate the entrainment of serpentines in the
concentrate.
Abstract: Interaction of Schiff base complexes of Iron and
Manganese: Iron [N, N’ Bis (5- (triphenyl phosphonium methyl)
salicylidene) -1, 2 ethanediamine) chloride, [Fe Salen]Cl; Manganese
[N, N’ Bis (5- (triphenyl phosphonium methyl) salicylidene) -1, 2
ethanediamine) acetate, were investigated by spectroscopic and
isothermal titration calorimetry techniques (ITC).
The absorbance spectra of complexes have shown hyper and
hypochromism in the presence of DNA that is indication of
interaction of complexes with DNA. The linear dichroism (LD)
measurements confirmed the bending of DNA in the presence of
complexes.
Furthermore, Isothermal titration calorimetry experiments
approved that complexes bound to DNA on the base of both
electrostatic and hydrophobic interactions. More, ITC profile exhibits
the existence of two binding phases for the complexes. Antibacterial
activity of ligand and complexes were tested in vitro to evaluate their
activity against the gram positive and negative bacteria.
Abstract: Ionic liquids consisting of a phosphonium cationic
moiety and a saccharinate anion are synthesized and compared with
their precursors, phosphonium chlorides, in reference to their
extraction efficiency towards L-lactic acid. On the base of
measurements of the acid and the water partitioning in the
equilibrium biphasic systems, the molar ratios between acid, water
and ionic liquid are estimated which allows to deduce the lactic acid
extractive pathway. The effect of a salting-out addition that
strengthens hydrophobicity in both phases is studied in view to reveal
the best biphasic system with respect to IL low toxicity and high
extraction efficiency.
Abstract: A quartz crystal microbalance (QCM) nanosensor was developed to detect lysozyme enzyme by functionalizing its gold surface with the attachment of poly(methacroyl-L-phenylalanine) (PMAPA) nanoparticles. PMAPA was chosen as a hydrophobic matrix. The hydrophobic nanoparticles were synthesized by micro-emulsion polymerization method. Hydrophobic QCM nanosensor was tested for real time detection of lysozyme enzyme from aqueous solution. The kinetic and affinity studies were determined by using lysozyme solutions with different concentrations. The responses related with mass (Δm) and frequency (Δf) shifts were used to evaluate adsorption properties.
Abstract: Polysulfone (PSU) is a specialty engineering polymer
having various industrial applications. PSU is especially used in
waste water treatment membranes due to its good mechanical
properties, structural and chemical stability. But it is a hydrophobic
material and therefore its surface aim to pollute easily. In order to
resolve this problem and extend the properties of membrane, PSU
surface is rendered hydrophilic by addition of the sepiolite
nanofibers. Sepiolite is one of the natural clays, which is a hydrate
magnesium silicate fiber, also one of the well known layered clays of
the montmorillonites where has several unique channels and pores
within. It has also moisture durability, strength and low price.
Sepiolite channels give great capacity of absorption and good surface
properties. In this study, nanocomposites of commercial PSU and
Sepiolite were prepared by solvent mixing method. Different organic
solvents and their mixtures were used. Rheological characteristics of
PSU-Sepiolite solvent mixtures were analyzed, the solubility of
nanocomposite content in those mixtures were studied.
Abstract: Liposome plays an important role in medical and
pharmaceutical science as e.g. nano scale drug carriers. Liposomes
are vesicles of varying size consisting of a spherical lipid bilayer and
an aqueous inner compartment. Magnet-driven liposome used for the
targeted delivery of drugs to organs and tissues. These liposome
preparations contain encapsulated drug components and finely
dispersed magnetic particles.
Liposomes are vesicles of varying size consisting of a spherical
lipid bilayer and an aqueous inner compartment that are generated in
vitro. These are useful in terms of biocompatibility, biodegradability,
and low toxicity, and can control biodistribution by changing the size,
lipid composition, and physical characteristics. Furthermore,
liposomes can entrap both hydrophobic and hydrophilic drugs and are
able to continuously release the entrapped substrate, thus being useful
drug carriers. Magnetic liposomes (MLs) are phospholipid vesicles
that encapsulate magneticor paramagnetic nanoparticles. They are
applied as contrast agents for magnetic resonance imaging (MRI).
The biological synthesis of nanoparticles using plant extracts plays
an important role in the field of nanotechnology. Green-synthesized
magnetite nanoparticles-protein hybrid has been produced by treating
Iron (III) / Iron (II) chloride with the leaf extract of Datura inoxia.
The phytochemicals present in the leaf extracts act as a reducing as
well stabilizing agents preventing agglomeration, which include
flavonoids, phenolic compounds, cardiac glycosides, proteins and
sugars.
The magnetite nanoparticles-protein hybrid has been trapped
inside the aqueous core of the liposome prepared by reversed phase
evaporation (REV) method using oleic and linoleic acid which has
been shown to be driven under magnetic field confirming the
formation magnetic liposome (ML). Chemical characterization of
stealth magnetic liposome has been performed by breaking the
liposome and release of magnetic nanoparticles. The presence iron
has been confirmed by colour complex formation with KSCN and
UV-Vis study using spectrophotometer Cary 60, Agilent.
This magnet driven liposome using nanoparticles-protein hybrid
can be a smart vesicles for the targeted drug delivery.
Abstract: In this research, waterglass based aerogel powder was
prepared by sol–gel process and ambient pressure drying. Inspired by
limited dust releasing, aerogel powder was introduced to the PET
electrospinning solution in an attempt to create required bulk and
surface structure for the nanofibers to improve their hydrophobic and
insulation properties. The samples evaluation was carried out by
measuring density, porosity, contact angle, heat transfer, FTIR, BET,
and SEM. According to the results, porous silica aerogel powder was
fabricated with mean pore diameter of 24 nm and contact angle of
145.9º. The results indicated the usefulness of the aerogel powder
confined into nanofibers to control surface roughness for
manipulating superhydrophobic nanowebs with water contact angle
of 147º. It can be due to a multi-scale surface roughness which was
created by nanowebs structure itself and nanofibers surface
irregularity in presence of the aerogels while a layer of fluorocarbon
created low surface energy. The wettability of a solid substrate is an
important property that is controlled by both the chemical
composition and geometry of the surface. Also, a decreasing trend in
the heat transfer was observed from 22% for the nanofibers without
any aerogel powder to 8% for the nanofibers with 4% aerogel
powder. The development of thermal insulating materials has become
increasingly more important than ever in view of the fossil energy
depletion and global warming that call for more demanding energysaving
practices.
Abstract: The mineral bioflotation represents a viable
alternative for the evaluation of new processes benefit alternative.
The adsorption bacteria on minerals surfaces will depend mainly on
the type of the microorganism as well as of the studied mineral
surface. In the current study, adhesion of S. carnosus on coal was
studied. Several methods were used as: DRX, Fourier Transform
Infra-Red (FTIR) adhesion isotherms and kinetic. The main goal is to
recovery of organic matter by the microflotation process on coal
particles with biological reagent (S. carnosus). Adhesion tests
revealed that adhesion took place after of 8 h at pH 9. The results
suggest that the adhesion of bacteria to solid substrates can be
considered an abiotic physicochemical process that is consequently
governed by bacterial surface properties such as their specific surface
area, hydrophobicity and surface functionalities. The greatest coal
fine flotability was of 75%, after 5 min of flotation.
Abstract: This research presents the design, fabrication and application of a flavor sensor for an integrated electronic tongue and electronic nose that can allow rapid characterization of multi-component mixtures in a solution. The odor gas and liquid are separated using hydrophobic porous membrane in micro fluidic channel. The sensor uses an array composed of microbeads in micromachined cavities localized on silicon wafer. Sensing occurs via colorimetric and fluorescence changes to receptors and indicator molecules that are attached to termination sites on the polymeric microbeads. As a result, the sensor array system enables simultaneous and near-real-time analyses using small samples and reagent volumes with the capacity to incorporate significant redundancies. One of the key parts of the system is a passive pump driven only by capillary force. The hydrophilic surface of the fluidic structure draws the sample into the sensor array without any moving mechanical parts. Since there is no moving mechanical component in the structure, the size of the fluidic structure can be compact and the fabrication becomes simple when compared to the device including active microfluidic components. These factors should make the proposed system inexpensive to mass-produce, portable and compatible with biomedical applications.
Abstract: Qatar’s primary source of fresh water is through
seawater desalination. Amongst the major processes that are
commercially available on the market, the most common large scale
techniques are Multi-Stage Flash distillation (MSF), Multi Effect
distillation (MED), and Reverse Osmosis (RO). Although commonly
used, these three processes are highly expensive down to high energy
input requirements and high operating costs allied with maintenance
and stress induced on the systems in harsh alkaline media. Beside that
cost, environmental footprint of these desalination techniques are
significant; from damaging marine eco-system, to huge land use, to
discharge of tons of GHG and huge carbon footprint.
Other less energy consuming techniques based on membrane
separation are being sought to reduce both the carbon footprint and
operating costs is membrane distillation (MD).
Emerged in 1960s, MD is an alternative technology for water
desalination attracting more attention since 1980s. MD process
involves the evaporation of a hot feed, typically below boiling point
of brine at standard conditions, by creating a water vapor pressure
difference across the porous, hydrophobic membrane. Main
advantages of MD compared to other commercially available
technologies (MSF and MED) and specially RO are reduction of
membrane and module stress due to absence of trans-membrane
pressure, less impact of contaminant fouling on distillate due to
transfer of only water vapor, utilization of low grade or waste heat
from oil and gas industries to heat up the feed up to required
temperature difference across the membrane, superior water quality,
and relatively lower capital and operating cost.
To achieve the objective of this study, state of the art flat-sheet
cross-flow DCMD bench scale unit was designed, commissioned, and
tested. The objective of this study is to analyze the characteristics and
morphology of the membrane suitable for DCMD through SEM
imaging and contact angle measurement and to study the water
quality of distillate produced by DCMD bench scale unit.
Comparison with available literature data is undertaken where
appropriate and laboratory data is used to compare a DCMD distillate
quality with that of other desalination techniques and standards.
Membrane SEM analysis showed that the PTFE membrane used
for the study has contact angle of 127º with highly porous surface
supported with less porous and bigger pore size PP membrane. Study
on the effect of feed solution (salinity) and temperature on water
quality of distillate produced from ICP and IC analysis showed that
with any salinity and different feed temperature (up to 70ºC) the
electric conductivity of distillate is less than 5 μS/cm with 99.99%
salt rejection and proved to be feasible and effective process capable
of consistently producing high quality distillate from very high feed
salinity solution (i.e. 100000 mg/L TDS) even with substantial
quality difference compared to other desalination methods such as
RO and MSF.
Abstract: The aim of present work was to optimize the effect of Ethyl Cellulose (EC) and Polyvinyl Pyrrolidone (PVP) concentration in extended release solid dispersion of Glibenclamide using combination of hydrophilic and hydrophobic polymers such as Polyvinyl Pyrrolidone and Ethyl cellulose. The advantage of solid dispersion technique provides a unique approach to particle size reduction and increased rates of dissolution. The compatibility studies of the drug and polymers were studied by TLC and results suggested no interaction between drug and polymers. Solid dispersions of Glibenclamide were prepared by common solvent evaporation method using Polyvinyl Pyrrolidone and Ethyl cellulose. The results indicated that homogeneous or heterogeneous conditions during the preparation methods employed governed the internal structures of the polymer matrices while retaining the drug in an amorphous form. F2 formulation prepared by solid dispersion method, displayed extended drug release followed by Higuchi matrix model indicating diffusion release of GLB from polymer matrices.
Abstract: The aim of this article is the measurement of the basic characteristic of superhydrophobic surfaces using high speed shadowgraphy. Here we describe the novel patented system for the industrial production of superhydrophobic surfaces. These surfaces were investigated with two optically based measurement methods: impinging drop and inclined wall. The results of the visualization and analysis help to state the suitable sample with superhydrophobic properties for mathematic simulation.
Abstract: Overhead electrical insulators form an important link in an electric power system. Along with the traditional insulators (i.e. glass and porcelain, etc) presently the polymeric insulators are also used world widely. These polymeric insulators are very sensitive to various environmental parameters such temperature, environmental pollution, UV-radiations, etc. which seriously effect their electrical, chemical and hydrophobic properties. The UV radiation level in the central region of Saudi Arabia is high as compared to the IEC standard for the accelerated aging of the composite insulators. Commonly used suspension type of composite EPDM (Ethylene Propylene Diene Monomer) insulator was subjected to accelerated stress aging as per modified IEC standard simulating the inland arid deserts atmospheric condition and also as per IEC-61109 standard. The hydrophobic characteristics were studied by measuring the contact angle along the insulator surface before and after the accelerated aging of the samples. It was found that EPDM insulator loses it hydrophobic properties proportional to the intensity of UV irradiations and its rate of recovery is also very low as compared to Silicone Rubber insulator.KeywordsEPDM, composite insulators, accelerated aging, hydrophobicity, contact angle.
Abstract: Addition of an oily waste to a co-composting process of dairy cow manure with food waste, and the influence in the final product was evaluated. Three static composting piles with different substrates concentrations were assessed. Sawdust was also added to all composting piles to attain 60%, humidity at the beginning of the process. In pile 1, the co-substrates were the solid-phase of dairy cow manure, food waste and sawdust as bulking agent. In piles 2 and 3 there was an extra input of oily waste of 7 and 11% of the total volume, respectively, corresponding to 18 and 28% in dry weight. The results showed that the co-composting process was feasible even at the highest fat content. Another positive effect due to the oily waste addition was the requirement of extra humidity, due to the hydrophobic properties of this specific waste, which may imply reduced need of a bulking agent. Moreover, this study shows that composting can be a feasible way of adding value to fatty wastes. The three final composts presented very similar and suitable properties for land application.
Abstract: This work presents the first results from the long-term laboratory experiment dealing with impact of drought on soil properties. Three groups of the treatment (A, B and C) with different regime of irrigation were prepared. The soil water content was maintained at 70 % of soil water holding capacity in group A, at 40 % in group B. In group C, soil water regime was maintained in the range of wilting point. Each group of the experiment was divided into three variants (A1 = B1, C1; A2 = B2, C2 etc.) with three repetitions: Variants A1 (B1, C1) were a controls without addition of another fertilizer. Variants A2 (B2, C2) were fertilized with mineral nitrogen fertilizer DAM 390 (0.140 Mg of N per ha) and variants A3 (B3, C3) contained 45 g of Cp per a pot.
The significant differences (ANOVA, P
Abstract: Adsorption of CS2 vapors has been studied on
different types of activated carbons obtained from different source
raw materials. The activated carbons have different surface areas and
are associated with varying amounts of the carbon-oxygen surface
groups. The adsorption of CS2 vapors is not directly related to surface
area, but is considerably influenced by the presence of carbonoxygen
surface groups. The adsorption decreases on increasing the
amount of carbon-oxygen surface groups on oxidation and increases
when these surface groups are eliminated on degassing. The
adsorption is maximum in case of the 950°-degassed carbon sample
which is almost completely free of any associated oxygen. The
kinetic data as analysed by Empirical diffusion model and Linear
driving force mass transfer model indicate that the adsorption does
not involve Fickian diffusion but may be considered as a pseudo first
order mass transfer process. The activation energy of adsorption and
isosteric enthalpies of adsorption indicate that the adsorption does not
involve interaction between CS2 and carbon-oxygen surface groups,
but hydrophobic interactions between CS2 and C-C atoms in the
carbon lattice.
Abstract: Calculations of energy efficiency of several AACbased
building envelopes under different climatic conditions are
presented. As thermal insulating materials, expanded polystyrene and
hydrophobic and hydrophilic mineral wools are assumed. The
computations are accomplished using computer code HEMOT
developed at Department of Materials Engineering, Faculty of Civil
Engineering at the Czech Technical University in Prague. The
climatic data of Athens, Kazan, Oslo, Prague and Reykjavík are
obtained using METEONORM software.
Abstract: Antimicrobial (AM) starch-based films were
developed by incorporating chitosan and lauric acid as antimicrobial
agent into starch-based film. Chitosan has wide range of applications
as a biomaterial, but barriers still exist to its broader use due to its
physical and chemical limitations. In this work, a series of
starch/chitosan (SC) blend films containing 8% of lauric acid was
prepared by casting method. The structure of the film was
characterized by Fourier transform infrared spectroscopy (FTIR), Xray
diffraction (XRD), and scanning electron microscopy (SEM).
The results indicated that there were strong interactions were present
between the hydroxyl groups of starch and the amino groups of
chitosan resulting in a good miscibility between starch and chitosan
in the blend films. Physical properties and optical properties of the
AM starch-based film were evaluated. The AM starch-based films
incorporated with chitosan and lauric acid showed an improvement in
water vapour transmission rate (WVTR) and addition of starch
content provided more transparent films while the yellowness of the
film attributed to the higher chitosan content. The improvement in
water barrier properties was mainly attributed to the hydrophobicity
of lauric acid and optimum chitosan or starch content. AM starch
based film also showed excellent oxygen barrier. Obtaining films
with good oxygen permeability would be an indication of the
potential use of these antimicrobial packaging as a natural packaging
and an alternative packaging to the synthetic polymer to protect food
from oxidation reactions