Abstract: In this paper, a field oriented control (FOC) induction motor drive is presented. In order to eliminate the speed sensor, an adaptation algorithm for tuning the rotor speed is proposed. Based on the Model Reference Adaptive System (MRAS) scheme, the rotor speed is tuned to obtain an exact FOC induction motor drive. The reference and adjustable models, developed in stationary stator reference frame, are used in the MRAS scheme to estimate induction rotor speed from measured terminal voltages and currents. The Integral Proportional (IP) gains speed controller are tuned by a modern approach that is the Particle Swarm Optimization (PSO) algorithm in order to optimize the parameters of the IP controller. The use of PSO as an optimization algorithm makes the drive robust, with faster dynamic response, higher accuracy and insensitive to load variation. The proposed algorithm has been tested by numerical simulation, showing the capability of driving load.
Abstract: In the paper the results of calculations of the dynamic
response of a multi-storey reinforced concrete building to a strong
mining shock originated from the main region of mining activity in
Poland (i.e. the Legnica-Glogow Copper District) are presented. The
representative time histories of accelerations registered in three
directions were used as ground motion data in calculations of the
dynamic response of the structure. Two variants of a numerical model
were applied: the model including only structural elements of the
building and the model including both structural and non-structural
elements (i.e. partition walls and ventilation ducts made of brick). It
turned out that non-structural elements of multi-storey RC buildings
have a small impact of about 10 % on natural frequencies of these
structures. It was also proved that the dynamic response of building
to mining shock obtained in case of inclusion of all non-structural
elements in the numerical model is about 20 % smaller than in case
of consideration of structural elements only. The principal stresses
obtained in calculations of dynamic response of multi-storey building
to strong mining shock are situated on the level of about 30% of
values obtained from static analysis (dead load).
Abstract: Due to increased number of terrorist attacks in recent years, loads induced by explosions need to be incorporated in building designs. For safer performance of a structure, its foundation should have sufficient strength and stability. Therefore, prior to any reconstruction or rehabilitation of a building subjected to blast, it is important to examine adverse effects on the foundation caused by blast induced ground shocks. This paper evaluates the effects of a buried explosion on a pile foundation. It treats the dynamic response of the pile in saturated sand, using explicit dynamic nonlinear finite element software LS-DYNA. The blast induced wave propagation in the soil and the horizontal deformation of pile are presented and the results are discussed. Further, a parametric study is carried out to evaluate the effect of varying the explosive shape on the pile response. This information can be used to evaluate the vulnerability of piled foundations to credible blast events as well as develop guidance for their design.
Abstract: The paper deals with the analysis of the dynamic
response of footbridges under human - induced dynamic loads.
This is a frequently occurring and often dominant load for
footbridges as it stems from the very purpose of a footbridge - to
convey pedestrian. Due to the emergence of new materials and
advanced engineering technology, slender footbridges are
increasingly becoming popular to satisfy the modern transportation
needs and the aesthetical requirements of the society. These
structures however are always lively with low stiffness, low mass,
low damping and low natural frequencies. As a consequence, they are
prone to vibration induced by human activities and can suffer severe
vibration serviceability problems, particularly in the lateral direction.
Pedestrian bridges are designed according to first and second limit
states, these are the criteria involved in response to static design load.
However, it is necessary to assess the dynamic response of bridge
design load on pedestrians and assess it impact on the comfort of the
user movement. Usually the load is considered a person or a small
group which can be assumed in perfect motion synchronization.
Already one person or small group can excite significant vibration of
the deck. In order to calculate the dynamic response to the movement
of people, designer needs available and suitable computational model
and criteria. For the calculation program ANSYS based on finite
element method was used.
Abstract: Recordings from recent earthquakes have provided evidence that ground motions in the near field of a rupturing fault differ from ordinary ground motions, as they can contain a large energy, or “directivity" pulse. This pulse can cause considerable damage during an earthquake, especially to structures with natural periods close to those of the pulse. Failures of modern engineered structures observed within the near-fault region in recent earthquakes have revealed the vulnerability of existing RC buildings against pulse-type ground motions. This may be due to the fact that these modern structures had been designed primarily using the design spectra of available standards, which have been developed using stochastic processes with relatively long duration that characterizes more distant ground motions. Many recently designed and constructed buildings may therefore require strengthening in order to perform well when subjected to near-fault ground motions. Fiber Reinforced Polymers are considered to be a viable alternative, due to their relatively easy and quick installation, low life cycle costs and zero maintenance requirements. The objective of this paper is to investigate the adequacy of Artificial Neural Networks (ANN) to determine the three dimensional dynamic response of FRP strengthened RC buildings under the near-fault ground motions. For this purpose, one ANN model is proposed to estimate the base shear force, base bending moments and roof displacement of buildings in two directions. A training set of 168 and a validation set of 21 buildings are produced from FEA analysis results of the dynamic response of RC buildings under the near-fault earthquakes. It is demonstrated that the neural network based approach is highly successful in determining the response.
Abstract: In this study, aeroelastic response and performance
analyses have been conducted for a 5MW-Class composite wind
turbine blade model. Advanced coupled numerical method based on
computational fluid dynamics (CFD) and computational flexible
multi-body dynamics (CFMBD) has been developed in order to
investigate aeroelastic responses and performance characteristics of
the rotating composite blade. Reynolds-Averaged Navier-Stokes
(RANS) equations with k-ω SST turbulence model were solved for
unsteady flow problems on the rotating turbine blade model. Also,
structural analyses considering rotating effect have been conducted
using the general nonlinear finite element method. A fully implicit
time marching scheme based on the Newmark direct integration
method is applied to solve the coupled aeroelastic governing equations
of the 3D turbine blade for fluid-structure interaction (FSI) problems.
Detailed dynamic responses and instantaneous velocity contour on the
blade surfaces which considering flow-separation effects were
presented to show the multi-physical phenomenon of the huge rotating
wind- turbine blade model.
Abstract: The design of Automatic Generation Control (AGC) system plays a vital role in automation of power system. This paper proposes Hybrid Neuro Fuzzy (HNF) approach for AGC of two-area interconnected reheat thermal power system with the consideration of Generation Rate Constraint (GRC). The advantage of proposed controller is that it can handle the system non-linearities and at the same time the proposed approach is faster than conventional controllers. The performance of HNF controller has been compared with that of both conventional Proportional Integral (PI) controller as well as Fuzzy Logic Controller (FLC) both in the absence and presence of Generation Rate Constraint (GRC). System performance is examined considering disturbance in each area of interconnected power system.
Abstract: It is known that the heart interacts with and adapts to
its venous and arterial loading conditions. Various experimental
studies and modeling approaches have been developed to investigate
the underlying mechanisms. This paper presents a model of the left
ventricle derived based on nonlinear stress-length myocardial
characteristics integrated over truncated ellipsoidal geometry, and
second-order dynamic mechanism for the excitation-contraction
coupling system. The results of the model presented here describe the
effects of the viscoelastic damping element of the electromechanical
coupling system on the hemodynamic response. Different heart rates
are considered to study the pacing effects on the performance of the
left-ventricle against constant preload and afterload conditions under
various damping conditions. The results indicate that the pacing
process of the left ventricle has to take into account, among other
things, the viscoelastic damping conditions of the myofilament
excitation-contraction process.
Abstract: The main objective of Automatic Generation Control (AGC) is to balance the total system generation against system load losses so that the desired frequency and power interchange with neighboring systems is maintained. Any mismatch between generation and demand causes the system frequency to deviate from its nominal value. Thus high frequency deviation may lead to system collapse. This necessitates a very fast and accurate controller to maintain the nominal system frequency. This paper deals with a novel approach of artificial intelligence (AI) technique called Hybrid Neuro-Fuzzy (HNF) approach for an (AGC). The advantage of this controller is that it can handle the non-linearities at the same time it is faster than other conventional controllers. The effectiveness of the proposed controller in increasing the damping of local and inter area modes of oscillation is demonstrated in a two area interconnected power system. The result shows that intelligent controller is having improved dynamic response and at the same time faster than conventional controller.
Abstract: The mechanical behavior of porous media is governed by the interaction between its solid skeleton and the fluid existing inside its pores. The interaction occurs through the interface of gains and fluid. The traditional analysis methods of porous media, based on the effective stress and Darcy's law, are unable to account for these interactions. For an accurate analysis, the porous media is represented in a fluid-filled porous solid on the basis of the Biot theory of wave propagation in poroelastic media. In Biot formulation, the equations of motion of the soil mixture are coupled with the global mass balance equations to describe the realistic behavior of porous media. Because of irregular geometry, the domain is generally treated as an assemblage of fmite elements. In this investigation, the numerical formulation for the field equations governing the dynamic response of fluid-saturated porous media is analyzed and employed for the study of transient wave motion. A finite element model is developed and implemented into a computer code called DYNAPM for dynamic analysis of porous media. The weighted residual method with 8-node elements is used for developing of a finite element model and the analysis is carried out in the time domain considering the dynamic excitation and gravity loading. Newmark time integration scheme is developed to solve the time-discretized equations which are an unconditionally stable implicit method Finally, some numerical examples are presented to show the accuracy and capability of developed model for a wide variety of behaviors of porous media.
Abstract: Earthquakes produce some of the most violent loading
situations that a structure can be subjected to and if a structure fails
under these loads then inevitably human life is put at risk. One of the
most common methods by which a structure fails under seismic
loading is at the connection of structural elements. The research
presented in this paper investigates the interlock systems as a novel
method for building structures. The main objective of this
experimental study wasto determine the dynamic characteristics and
the seismic behaviour of the proposed structures compared to
conventional structural systemsduring seismic motions. Results of
this study indicate that the interlock mechanism of the panels
influences the behaviour of lateral load-resisting systems of the
structures during earthquakes, contributing to better structural
flexibility and easier maintenance.
Abstract: In the paper a detailed analysis of the dynamic
response of a cooling tower shell to mining tremors originated from
two main regions of mining activity in Poland (Upper Silesian Coal
Basin and Legnica-Glogow Copper District) was presented. The
representative time histories registered in the both regions were used
as ground motion data in calculations of the dynamic response of the
structure. It was proved that the dynamic response of the shell is
strongly dependent not only on the level of vibration amplitudes but
on the dominant frequency range of the mining shock typical for the
mining region as well. Also a vertical component of vibrations
occurred to have considerable influence on the total dynamic
response of the shell. Finally, it turned out that non-uniformity of
kinematic excitation resulting from spatial variety of ground motion
plays a significant role in dynamic analysis of large-dimensional
shells under mining shocks.
Abstract: This paper will focus on modeling, analysis and simulation of a 42V/14V dc/dc converter based architecture. This architecture is considered to be technically a viable solution for automotive dual-voltage power system for passenger car in the near further. An interleaved dc/dc converter system is chosen for the automotive converter topology due to its advantages regarding filter reduction, dynamic response, and power management. Presented herein, is a model based on one kilowatt interleaved six-phase buck converter designed to operate in a Discontinuous Conduction Mode (DCM). The control strategy of the converter is based on a voltagemode- controlled Pulse Width Modulation (PWM) with a Proportional-Integral-Derivative (PID). The effectiveness of the interleaved step-down converter is verified through simulation results using control-oriented simulator, MatLab/Simulink.
Abstract: Considering the merits and limitations of energy dissipation system, seismic isolation system and suspension system, a new earthquake resistant system is proposed and is demonstrated numerically through a frame-core structure. Base isolators and story isolators are installed in the proposed system. The former “isolates" the frame from the foundation and the latter “separates" the frame from the center core. Equations of motion are formulated to study the response of the proposed structural system to strong earthquake motion. As compared with the fixed-base building system, the proposed structural system shows substantial reduction on structural response.
Abstract: As a part of the development of a numerical method of
close capture exhausts systems for machining devices, a test rig
recreating a situation similar to a grinding operation, but in a
perfectly controlled environment, is used. The properties of the
obtained spray of solid particles are initially characterized using
particle tracking velocimetry (PTV), in order to obtain input and
validation parameters for numerical simulations. The dispersion of a
tracer gas (SF6) emitted simultaneously with the particle jet is then
studied experimentally, as the dispersion of such a gas is
representative of that of finer particles, whose aerodynamic response
time is negligible. Finally, complete modeling of the test rig is
achieved to allow comparison with experimental results and thus to
progress towards validation of the models used to describe a twophase
flow generated by machining operation.
Abstract: This paper investigates the effectiveness of the use of
seismic isolation devices on the overall 3D seismic response of
curved highway viaducts with an emphasis on expansion joints.
Furthermore, an evaluation of the effectiveness of the use of cable
restrainers is presented. For this purpose, the bridge seismic
performance has been evaluated on four different radii of curvature,
considering two cases: restrained and unrestrained curved viaducts.
Depending on the radius of curvature, three-dimensional non-linear
dynamic analysis shows the vulnerability of curved viaducts to
pounding and deck unseating damage. In this study, the efficiency of
using LRB supports combined with cable restrainers on curved
viaducts is demonstrated, not only by reducing in all cases the
possible damage, but also by providing a similar behavior in the
viaducts despite of curvature radius.
Abstract: In this paper, based on the coupled-mode and carrier rate equations, derivation of a dynamic model and numerically analysis of a MQW chirped DFB-SOA all-optical flip-flop is done precisely. We have analyzed the effects of strains of QW and MQW and cross phase modulation (XPM) on the dynamic response, and rise and fall times of the DFB-SOA all optical flip flop. We have shown that strained MQW active region in under an optimized condition into a DFB-SOA with chirped grating can improve the switching ON speed limitation in such a of the device, significantly while the fall time is increased. The values of the rise times for such an all optical flip-flop, are obtained in an optimized condition, areas tr=255ps.
Abstract: It is known that the heart interacts with and adapts to its venous and arterial loading conditions. Various experimental studies and modeling approaches have been developed to investigate the underlying mechanisms. This paper presents a model of the left ventricle derived based on nonlinear stress-length myocardial characteristics integrated over truncated ellipsoidal geometry, and second-order dynamic mechanism for the excitation-contraction coupling system. The results of the model presented here describe the effects of the viscoelastic damping element of the electromechanical coupling system on the hemodynamic response. Different heart rates are considered to study the pacing effects on the performance of the left-ventricle against constant preload and afterload conditions under various damping conditions. The results indicate that the pacing process of the left ventricle has to take into account, among other things, the viscoelastic damping conditions of the myofilament excitation-contraction process. The effects of left ventricular dimensions on the hemdynamic response have been examined. These effects are found to be different at different viscoelastic and pacing conditions.
Abstract: Natural frequencies and dynamic response of a spur
gear sector are investigated using a two dimensional finite element
model that offers significant advantages for dynamic gear analyses.
The gear teeth are analyzed for different operating speeds. A primary
feature of this modeling is determination of mesh forces using a
detailed contact analysis for each time step as the gears roll through
the mesh. ANSYS software has been used on the proposed model to
find the natural frequencies by Block Lanczos technique and
displacements and dynamic stresses by transient mode super position
method. The effect of rotational speed of the gear on the dynamic
response of gear tooth has been studied and design limits have been
discussed.
Abstract: In order to improve the effect of isolation structure, the
principles and behaviours of the base-isolation system are studied, and
the types and characteristics of the base-isolation are also discussed.
Compared to the traditional aseismatic structures, the base isolation
structures decrease the seismic response obviously: the total structural
aseismatic value decreases to 1/4-1/32 and the seismic shear stress in
the upper structure decreases to 1/14-1/23. In the huge seism, the
structure can have an obvious aseismatic effect.