Abstract: A total of fourteen slab-edge beam-column connection specimens were tested gradually to failure under the effect of simultaneous action of shear force and moment. The objective was to investigate the influence of some parameters thought to be important on the behavior and strength of slab-column connections with edge beams encountered in flat slab flooring and roofing systems. The parameters included the existence and strength of edge beam, depth and width of edge beam, steel reinforcement ratio of slab, ratio of moment to shear force, and the existence of openings in the region next to the column.
Results obtained demonstrated the importance of the studied parameters on the strength and behavior of slab-column connections with edge beams.
Abstract: The performance of adaptive beamforming degrades
substantially in the presence of steering vector mismatches. This
degradation is especially severe in the near-field, for the
3-dimensional source location is more difficult to estimate than the
2-dimensional direction of arrival in far-field cases. As a solution, a
novel approach of near-field robust adaptive beamforming (RABF) is
proposed in this paper. It is a natural extension of the traditional
far-field RABF and belongs to the class of diagonal loading
approaches, with the loading level determined based on worst-case
performance optimization. However, different from the methods
solving the optimal loading by iteration, it suggests here a simple
closed-form solution after some approximations, and consequently,
the optimal weight vector can be expressed in a closed form. Besides
simplicity and low computational cost, the proposed approach reveals
how different factors affect the optimal loading as well as the weight
vector. Its excellent performance in the near-field is confirmed via a
number of numerical examples.
Abstract: This paper reports the evolving properties of a 3 mm low carbon steel plate after Laser Beam Forming achieve this objective, the chemical analyse material and the formed components were carried thereafter both were characterized through microhardness profiling microstructural evaluation and tensile testing. showed an increase in the elemental concentration of the component when compared to the as received attributed to the enhancement property of the LBF process Ultimate Tensile Strength (UTS) and the Vickers the formed component shows an increase when compared to the as received material, this was attributed to strain hardening and grain refinement brought about by the LBF process. The microstructure of the as received steel consists of equiaxed ferrit that of the formed component exhibits elongated orming process (LBF). To es of the as received out and compared; profiling, The chemical analyses formed material; this can be process. The microhardness of ferrite and pearlite while grains.
Abstract: Simplified coupled engine block-crankshaft models
based on beam theory provide an efficient substitute to engine
simulation in the design process. These models require accurate
definition of the main bearing stiffness. In this paper, an investigation
of this stiffness is presented. The clearance effect is studied using a
smooth bearing model. It is manifested for low shaft displacement.
The hydrodynamic assessment model shows that the oil film has no
stiffness for low loads and it is infinitely rigid for important loads.
The deformation stiffness is determined using a suitable finite
elements model based on real CADs. As a result, a main bearing
behaviour law is proposed. This behaviour law takes into account the
clearance, the hydrodynamic sustention and the deformation stiffness.
It ensures properly the transition from the configuration low rigidity
to the configuration high rigidity.
Abstract: This paper presents the adaptive control scheme
with sliding mode compensator for vibration control problem
in the presence of disturbance. The dynamic model of the
flexible cantilever beam using finite element modeling is
derived. The adaptive control with sliding mode compensator
using output feedback for output tracking is developed to
reject the external disturbance, and to improve the tracking
performance. Satisfactory simulation results verify that the
effectiveness of adaptive control scheme with sliding mode
compensator.
Abstract: This paper adopted the hybrid differential transform approach for studying heat transfer problems in a gold/chromium thin film with an ultra-short-pulsed laser beam projecting on the gold side. The physical system, formulated based on the hyperbolic two-step heat transfer model, covers three characteristics: (i) coupling effects between the electron/lattice systems, (ii) thermal wave propagation in metals, and (iii) radiation effects along the interface. The differential transform method is used to transfer the governing equations in the time domain into the spectrum equations, which is further discretized in the space domain by the finite difference method. The results, obtained through a recursive process, show that the electron temperature in the gold film can rise up to several thousand degrees before its electron/lattice systems reach equilibrium at only several hundred degrees. The electron and lattice temperatures in the chromium film are much lower than those in the gold film.
Abstract: Many applications require surface modification and
micro-structuring of polymers. For these purposes is mainly used
ultraviolet (UV) radiation from excimer lamps or excimer lasers.
However, these sources have a decided disadvantage - degrading the
polymer deep inside due to relatively big radiation penetration depth
which may exceed 100 μm. In contrast, extreme ultraviolet (EUV)
radiation is absorbed in a layer approximately 100 nm thick only. In
this work, the radiation from a discharge-plasma EUV source (with
wavelength 46.9 nm) based on a capillary discharge driver is focused
with a spherical Si/Sc multilayer mirror for surface modification of
PMMA sample or thin gold layer (thickness about 40 nm). It was
found that the focused EUV laser beam is capable by one shot to
ablate PMMA or layer of gold, even if the focus is significantly
influenced by astigmatism.
Abstract: This paper investigates experimental studies on
vibration suppression for a cantilever beam using an
Electro-Rheological (ER) sandwich shock absorber. ER fluid (ERF) is a
class of smart materials that can undergo significant reversible changes
immediately in its rheological and mechanical properties under the
influence of an applied electric field. Firstly, an ER sandwich beam is
fabricated by inserting a starch-based ERF into a hollow composite
beam. At the same time, experimental investigations are focused on the
frequency response of the ERF sandwich beam. Second, the ERF
sandwich beam is attached to a cantilever beam to become as a shock
absorber. Finally, a fuzzy semi-active vibration control is designed to
suppress the vibration of the cantilever beam via the ERF sandwich
shock absorber. To check the consistency of the proposed fuzzy
controller, the real-time implementation validated the performance of
the controller.
Abstract: Delamination between layers in composite materials is a major structural failure. The delamination resistance is quantified by the critical strain energy release rate (SERR). The present investigation deals with the strain energy release rate of two woven fabric composites. Materials used are made of two types of glass fiber (360 gsm and 600 gsm) of plain weave and epoxy as matrix. The fracture behavior is studied using the mode I, double cantilever beam test and the mode II, end notched flexure test, in order to determine the energy required for the initiation and growth of an artificial crack. The delamination energy of these two materials is compared in order to study the effect of weave and reinforcement on mechanical properties. The fracture mechanism is also analyzed by means of scanning electron microscopy (SEM). It is observed that the plain weave fabric composite with lesser strand width has higher inter laminar fracture properties compared to the plain weave fabric composite with more strand width.
Abstract: A tunable photonic microwave bandpass filter with
negative coefficient based on an electro-optic phase modulator (EOPM) and a variable polarization beamsplitter (VPBS) is
demonstrated. A two-tap microwave bandpass filter with one negative coefficient is presented. The chromatic dispersion and
optical coherence are not affected on this filter.
Abstract: Rotational Smart Lighting Control System can supply
the quantity of lighting which is required to run plants by rotating few
LED and Fluorescent instead of that are used in the existing plant
factories.The initial installation of the existing plants factory is
expensive, so in order to solve the problem with smart lighting control
system was developed.
The beam required intensity for the growth of crops, Photosynthetic
Photon Flux Density(PPFD)is calculated; and the number of LED, are
installed on the blades, set; using the Lighting Simulation
Program.Relux, it is able to confirm that the difference of the beam
intensity between the center and the outer of lighting system when the
lighting device is rotating.
Abstract: In this paper, an extended method of the directionally constrained minimization of power (DCMP) algorithm for broadband signals is proposed. The DCMP algorithm is one of the useful techniques of extracting a target signal from observed signals of a microphone array system. In the DCMP algorithm, output power of the microphone array is minimized under a constraint of constant responses to directions of arrival (DOAs) of specific signals. In our algorithm, by limiting the directional constraint to the perpendicular direction to the sensor array system, the calculating time is reduced.
Abstract: This paper deals with analysis of flexural stiffness,
indentation and their energies in three point loading of sandwich
beams with composite faces from Eglass/epoxy and cores from
Polyurethane or PVC. Energy is consumed in three stages of
indentation in laminated beam, indentation of sandwich beam and
bending of sandwich beam. Theory of elasticity is chosen to present
equations for indentation of laminated beam, then these equations
have been corrected to offer better results. An analytical model has
been used assuming an elastic-perfectly plastic compressive behavior
of the foam core. Classical theory of beam is used to describe three
point bending. Finite element (FE) analysis of static indentation
sandwich beams is performed using the FE code ABAQUS. The
foam core is modeled using the crushable foam material model and
response of the foam core is experimentally characterized in uniaxial
compression.
Three point bending and indentation have been done
experimentally in two cases of low velocity and higher velocity
(quasi-impact) of loading. Results can describe response of beam in
terms of core and faces thicknesses, core material, indentor diameter,
energy absorbed, and length of plastic area in the testing. The
experimental results are in good agreement with the analytical and
FE analyses. These results can be used as an introduction for impact
loading and energy absorbing of sandwich structures.
Abstract: This research was conducted to develop a correlation
between microstructure of HSLA steel and the mechanical properties
that occur as a result of both laser and mechanical forming processes
of the metal. The technique of forming flat metals by applying laser
beams is a relatively new concept in the manufacturing industry.
However, the effects of laser energy on the stability of metal alloy
phases have not yet been elucidated in terms of phase
transformations and microhardness. In this work, CO2 laser source
was used to irradiate the surface of a flat metal then the
microstructure and microhardness of the metal were studied on the
formed specimen. The extent to which the microstructure changed
depended on the heat inputs of up to 1000 J/cm2 with cooling rates of
about 4.8E+02 K/s. Experimental results revealed that the irradiated
surface of a HSLA steel had transformed to austenitic structure
during the heating process.
Abstract: Researchers investigate arious strategies to develop composite beams and maximize the structural advantages. This study
attempted to conduct experiments and analysis of changes in the
neutral axis of positive moments of a Green Beam. Strain
compatibility analysis was used, and its efficiency was demonstrated
by comparing experimental and analytical values. In the comparison of
neutral axis, the difference between experimental and analytical values
was found to range from 8.8~26.2%. It was determined that strain
compatibility analysis can be useful for predicting the behaviors of
composite beams, with the ability to predict the behavior of not only
the elastic location of the composite member, but also of the plastic
location
Abstract: In this paper, transversal vibration of buried pipelines
during loading induced by underground explosions is analyzed. The
pipeline is modeled as an infinite beam on an elastic foundation, so
that soil-structure interaction is considered by means of transverse
linear springs along the pipeline. The pipeline behavior is assumed to
be ideal elasto-plastic which an ultimate strain value limits the plastic
behavior. The blast loading is considered as a point load, considering
the affected length at some point of the pipeline, in which the
magnitude decreases exponentially with time. A closed-form solution
for the quasi-static problem is carried out for both elastic and elasticperfect
plastic behaviors of pipe materials. At the end, a comparative
study on steel and polyethylene pipes with different sizes buried in
various soil conditions, affected by a predefined underground
explosion is conducted, in which effect of each parameter is
discussed.
Abstract: In this paper, an improved ant colony optimization
(ACO) algorithm is proposed to enhance the performance of global
optimum search. The strategy of the proposed algorithm has the
capability of fuzzy pheromone updating, adaptive parameter tuning,
and mechanism resetting. The proposed method is utilized to tune the
parameters of the fuzzy controller for a real beam and ball system.
Simulation and experimental results indicate that better performance
can be achieved compared to the conventional ACO algorithms in the
aspect of convergence speed and accuracy.
Abstract: This paper reports the fatigue crack growth behaviour
of gas tungsten arc, electron beam and laser beam welded Ti-6Al-4V
titanium alloy. Centre cracked tensile specimens were prepared to
evaluate the fatigue crack growth behaviour. A 100kN servo
hydraulic controlled fatigue testing machine was used under constant
amplitude uniaxial tensile load (stress ratio of 0.1 and frequency of
10 Hz). Crack growth curves were plotted and crack growth
parameters (exponent and intercept) were evaluated. Critical and
threshold stress intensity factor ranges were also evaluated. Fatigue
crack growth behaviour of welds was correlated with mechanical
properties and microstructural characteristics of welds. Of the three
joints, the joint fabricated by laser beam welding exhibited higher
fatigue crack growth resistance due to the presence of fine lamellar
microstructure in the weld metal.
Abstract: A high energy dual-wavelength extracavity KTA
optical parametric oscillator (OPO) with excellent stability and beam
quality, which is pumped by a Q-switched single-longitudinal-mode
Nd:YAG laser, has been demonstrated based on a type II noncritical
phase matching (NCPM) KTA crystal. The maximum pulse energy of
10.2 mJ with the output stability of better than 4.1% rms at 3.467 μm is
obtained at the repetition rate of 10 Hz and pulse width of 2 ns, and the
11.9 mJ of 1.535 μm radiation is obtained simultaneously. This
extracavity NCPM KTA OPO is very useful when high energy, high
beam quality and smooth time domain are needed.
Abstract: In the present work, behavior of inoxydable steel as
reinforcement bar in composite concrete is being investigated. The
bar-concrete adherence in reinforced concrete (RC) beam is studied
and focus is made on the tension stiffening parameter. This study
highlighted an approach to observe this interaction behavior in
bending test instead of direct tension as per reported in many
references. The approach resembles actual loading condition of the
structural RC beam. The tension stiffening properties are then
applied to numerical finite element analysis (FEA) to verify their
correlation with laboratory results. Comparison with laboratory
shows a good correlation between the two. The experimental settings
is able to determine tension stiffening parameters in RC beam and
the modeling strategies made in ABAQUS can closely represent the
actual condition. Tension stiffening model used can represent the
interaction properties between inoxydable steel and concrete.