Abstract: Lake Nasser is one of the largest reservoirs in the
world. Over 120 million metric tons of sediments are deposited in its
dead storage zone every year. The main objective of the present work
was to determine the physical and chemical characteristics of Lake
Nasser sediments. The sample had a relatively low surface area of 2.9
m2/g which increased more than 3-fold upon chemical activation. The
main chemical elements of the raw sediments were C, O and Si with
some traces of Al, Fe and Ca. The organic functional groups for the
tested sample included O-H, C=C, C-H and C-O, with indications of
Si-O and other metal-C and/or metal-O bonds normally associated
with clayey materials. Potentiometric titration of the sample in
different ionic strength backgrounds revealed an alkaline material with
very strong positive surface charge at pH values just a little less than
the pH of zero charge which is ~9. Surface interactions of the
sediments with the background electrolyte were significant. An
advanced surface complexation model was able to capture these
effects, employing a single-site approach to represent protolysis
reactions in aqueous solution, and to determine the significant surface
species in the pH range of environmental interest.
Abstract: In recent five decades, textured yarns of polyester fiber produced by false twist method are the most
important and mass-produced manmade fibers. There are
many parameters of cross section which affect the physical and mechanical properties of textured yarns. These parameters
are surface area, perimeter, equivalent diameter, large
diameter, small diameter, convexity, stiffness, eccentricity, and hydraulic diameter. These parameters were evaluated by
digital image processing techniques. To find trends between production criteria and evaluated parameters of cross section, three criteria of production line have been adjusted and different types of yarns were produced. These criteria are
temperature, drafting ratio, and D/Y ratio. Finally the relations between production criteria and cross section parameters were
considered. The results showed that the presented technique can recognize and measure the parameters of fiber cross section in acceptable accuracy. Also, the optimum condition
of adjustments has been estimated from results of image analysis evaluation.
Abstract: Air emissions from waste treatment plants often
consist of a combination of Volatile Organic Compounds (VOCs)
and odors. Hydrogen sulfide is one of the major odorous gases
present in the waste emissions coming from municipal wastewater
treatment facilities. Hydrogen sulfide (H2S) is odorous, highly toxic
and flammable. Exposure to lower concentrations can result in eye
irritation, a sore throat and cough, shortness of breath, and fluid in
the lungs. Biofiltration has become a widely accepted technology for
treating air streams containing H2S. When compared with other nonbiological
technologies, biofilter is more cost-effective for treating large
volumes of air containing low concentrations of biodegradable compounds.
Optimization of biofilter media is essential for many reasons such as:
providing a higher surface area for biofilm growth, low pressure drop,
physical stability, and good moisture retention. In this work, a novel
biofilter media is developed and tested at a pumping station of a
municipality located in the United Arab Emirates (UAE). The
media is found to be very effective (>99%) in removing H2S
concentrations that are expected in pumping stations under steady
state and shock loading conditions.
Abstract: Work is focused to the study of unburned carbon in
ash from coal (and wastes) combustion in 8 combustion tests at 3
fluidised-bed power station, at co-combustion of coal and wastes
(also at fluidized bed) and at bench-scale unit simulating coal
combustion in small domestic furnaces. The attention is paid to
unburned carbon contents in bottom ashes and fly ashes at these 8
combustion tests and to morphology of unburned carbons. Specific
surface area of coals, unburned carbons and ashes and the relation of
specific surface area of unburned carbon and the content of volatile
combustibles in coal were studied as well.
Abstract: Fly ash is a significant waste that is released of
thermal power plants and defined as very fine particles that are drifted upward with up taken by the flue gases due to the burning of
used coal [1]. The fly-ash is capable of removing organic
contaminants in consequence of high carbon content, a large surface area per unit volume and contained heavy metals. Therefore, fly ash
is used as an effective coagulant and adsorbent by pelletization [2, 3].
In this study, the possibility of use of fly ash taken from Turkey like low-cost adsorbent for adsorption of zinc ions found in waste
water was investigated. The fly ash taken from Turkey was pelletized with bentonite and molass to evaluate the adsorption capaticity. For
this purpose; analyses such as sieve analysis, XRD, XRF, FTIR and SEM were performed. As a result, it was seen that pellets prepared
from fly ash, bentonite and molass would be used for zinc adsorption.
Abstract: The efficiency of chitosan beads processed from 4
marine animal shells; white leg shrimp (Litopenaeus vannamei), mud
crab (Scylla sp.), horseshoe crab (Carcinoscorpius rotundicauda),
and cuttlefish bone (Sepia sp.), for the adsorption experiments of
ammonia and formaldehyde were investigated. The porosities of
chitosan from the shells looked like beads were distinctly examined
under SEM. The original pores of those shells on the surface areas
compose of evenly fine pores. The shell beads of cuttlefish bone and
horseshoe crab show the larger probably even porosity, while on
those white leg shrimp and mud crab contain various large and fine
pores. The best adsorption at pH 9 in 18 mg/l ammonia at 2 hours
yield on cuttlefish bone, horseshoe crab, mud crab and white leg
shrimp with the average percent of 59.12, 51.45, 45.66 and 43.52,
respectively. Within 30 minutes the formaldehyde absorbers (at pH 5
in 8 μg/ml) revealed 46.27, 26.56, and 18.04 percent capacities in
cuttlefish bone, mud crab and white leg shrimp beads; while 22.44
percent in the horseshoe crab at pH 7. The adsorption capacities and
the amounts of beads showed a positive correlation. The adsorption
capacity relationship between pH and the gas concentrations were
affected by these qualities of chitosan beads.
Abstract: In this study, we used a two-stage process and
potassium hydroxide (KOH) to transform waste biomass (rice straw)
into activated carbon and then evaluated the adsorption capacity of the
waste for removing carbofuran from an aqueous solution. Activated
carbon was fast and effective for the removal of carbofuran because of
its high surface area. The native and carbofuran-loaded adsorbents
were characterized by elemental analysis. Different adsorption
parameters, such as the initial carbofuran concentration, contact time,
temperature and pH for carbofuran adsorption, were studied using a
batch system. This study demonstrates that rice straw can be very
effective in the adsorption of carbofuran from bodies of water.
Abstract: The kinetics of palm oil catalytic cracking over
aluminum containing mesoporous silica Al-MCM-41 (5% Al) was
investigated in a batch autoclave reactor at the temperatures range of
573 – 673 K. The catalyst was prepared by using sol-gel technique
and has been characterized by nitrogen adsorption and x-ray
diffraction methods. Surface area of 1276 m2/g with average pore
diameter of 2.54 nm and pore volume of 0.811 cm3/g was obtained.
The experimental catalytic cracking runs were conducted using 50 g
of oil and 1 g of catalyst. The reaction pressure was recorded at
different time intervals and the data were analyzed using Levenberg-
Marquardt (LM) algorithm using polymath software. The results
show that the reaction order was found to be -1.5 and activation
energy of 3200 J/gmol.
Abstract: Zeolite A and MCM-41 have extensive applications in basic science, petrochemical science, energy conservation/storage, medicine, chemical sensor, air purification, environmentally benign composite structure and waste remediation. However, the use of zeolite A and MCM-41 in these areas, especially environmental remediation, are restricted due to prohibitive production cost. Efficient recycling of and resource recovery from coal fly ash has been a major topic of current international research interest, aimed at achieving sustainable development of human society from the viewpoints of energy, economy, and environmental strategy. This project reported an original, novel, green and fast methods to produce nano-porous zeolite A and MCM-41 materials from coal fly ash. For zeolite A, this novel production method allows a reduction by half of the total production time while maintaining a high degree of crystallinity of zeolite A which exists in a narrower particle size distribution. For MCM-41, this remarkably green approach, being an environmentally friendly process and reducing generation of toxic waste, can produce pure and long-range ordered MCM-41 materials from coal fly ash. This approach took 24 h at 25 oC to produce 9 g of MCM-41 materials from 30 g of the coal fly ash, which is the shortest time and lowest reaction temperature required to produce pure and ordered MCM-41 materials (having the largest internal surface area) compared to the values reported in the literature. Performance evaluation of the produced zeolite A and MCM-41 materials in wastewater treatment and air pollution control were reported. The residual fly ash was also converted to zeolite Na-P1 which showed good performance in removal of multi-metal ions in wastewater. In wastewater treatment, compared to commercial-grade zeolite A, adsorbents produced from coal fly ash were effective in removing multi heavy metal ions in water and could be an alternative material for treatment of wastewater. In methane emission abatement, the zeolite A (produced from coal fly ash) achieved similar methane removal efficiency compared to the zeolite A prepared from pure chemicals. This report provides the guidance for production of zeolite A and MCM-41 from coal fly ash by a cost-effective approach which opens potential applications of these materials in environmental industry. Finally, environmental and economic aspects of production of zeolite A and MCM-41 from coal fly ash were discussed.
Abstract: Physical and mechanical properties of Russian olive
fruits were measured at moisture content of 14.43% w.b. The results
revealed that the mean length, width and thickness of Russian olive
fruits were 20.72, 15.73 and 14.69mm, respectively. Mean mass and
volume of Russian olive fruits were measured as 1.45 g and 2.55 cm3,
respectively. The sphericity, aspect ratio and surface area were
calculated as 0.81, 0.72 and 8.96 cm2, respectively, while arithmetic
mean diameter, geometric mean diameter and equivalent diameter of
Russian olive fruits were 17.05, 16.83 and 16.84 mm, respectively.
Whole fruit density, bulk density and porosity of jujube fruits were
measured and found to be 1.01 g/cm3, 0.29 g/cm3 and 69.5%,
respectively. The values of static coefficient of friction on three
surfaces of glass, galvanized iron and plywood were 0.35, 0.36 and
0.43, respectively. The skin color (L*, a*, b*) varied from 9.92 to
16.08; 2.04 to 3.91 and 1.12 to 3.83, respectively. The values of
rupture force, deformation, energy absorbed and hardness were found
to be between 12.14-16.85 N, 2.16-4.25 mm, 3.42-6.99 N mm and
17.1-23.85 N/mm.
Abstract: Biofuels, like biobutanol, have been recognized for
being renewable and sustainable fuels which can be produced from
lignocellulosic biomass. To convert lignocellulosic biomass to
biofuel, pretreatment process is an important step to remove
hemicelluloses and lignin to improve enzymatic hydrolysis. Dilute
acid pretreatment has been successful developed for pretreatment of
corncobs and the optimum conditions of dilute sulfuric and
phosphoric acid pretreatment were obtained at 120 °C for 5 min with
15:1 liquid to solid ratio and 140 °C for 10 min with 10:1 liquid to
solid ratio, respectively. The result shows that both of acid
pretreatments gave the content of total sugar approximately 34–35
g/l. In case of inhibitor content (furfural), phosphoric acid
pretreatment gives higher than sulfuric acid pretreatment.
Characterizations of corncobs after pretreatment indicate that both of
acid pretreatments can improve enzymatic accessibility and the better
results present in corncobs pretreated with sulfuric acid in term of
surface area, crystallinity, and composition analysis.
Abstract: The remediation of water resources pollution in
developing countries requires the application of alternative
sustainable cheaper and efficient end-of-pipe wastewater treatment
technologies. The feasibility of use of South African cheap and
abundant pine tree (Pinus patula) sawdust for development of lowcost
AC of comparable quality to expensive commercial ACs in the
abatement of water pollution was investigated. AC was developed at
optimized two-stage N2-superheated steam activation conditions in a
fixed bed reactor, and characterized for proximate and ultimate
properties, N2-BET surface area, pore size distribution, SEM, pHPZC
and FTIR. The sawdust pyrolysis activation energy was evaluated by
TGA. Results indicated that the chars prepared at 800oC and 2hrs
were suitable for development of better quality AC at 800oC and 47%
burn-off having BET surface area (1086m2/g), micropore volume
(0.26cm3/g), and mesopore volume (0.43cm3/g) comparable to
expensive commercial ACs, and suitable for water contaminants
removal. The developed AC showed basic surface functionality at
pHPZC at 10.3, and a phenol adsorption capacity that was higher than
that of commercial Norit (RO 0.8) AC. Thus, it is feasible to develop
better quality low-cost AC from (Pinus patula) sawdust using twostage
N2-steam activation in fixed-bed reactor.
Abstract: Palm shell obtained from coastal part of southern
India was studied for the removal for the adsorption of Hg (II) ions.
Batch adsorption experiments were carried out as a function of pH,
concentration of Hg (II) ions, time, temperature and adsorbent dose.
Maximum removal was seen in the range pH 4.0- pH 7.0. The palm
shell powder used as adsorbent was characterized for its surface area,
SEM, PXRD, FTIR, ion exchange capacity, moisture content, and
bulk density, soluble content in water and acid and pH. The
experimental results were analyzed using Langmuir I, II, III, IV and
Freundlich adsorption isotherms. The batch sorption kinetics was
studied for the first order reversible reaction, pseudo first order;
pseudo second order reaction and the intra-particle diffusion reaction.
The biomass was successfully used for removal Hg (II) from
synthetic and industrial effluents and the technique appears
industrially applicable and viable.
Abstract: Several studies have shown the association between
ambient particulate matter (PM) and adverse health effects and
climate change, thus highlighting the need to limit the anthropogenic
sources of PM. PM Exposure is commonly monitored as mass
concentration of PM10 (particle aerodynamic diameter < 10μm) or
PM2.5 (particle aerodynamic diameter < 2.5μm), although increasing
toxicity with decreasing aerodynamic diameter has been reported due
to increased surface area and enhanced chemical reactivity with other
species. Additionally, the light scattering properties of PM increases
with decreasing size. Hence, it is important to study the chemical
characterization of finer fraction of the particulate matter and to
identify their sources so that they can be controlled appropriately to a
large extent at the sources before reaching to the receptors.
Abstract: A composite made of plasma functionalized multiwall
carbon nanotubes (MWNTs) coated with SnO2 was synthesized by
sonochemical precipitation method. Thick layer of this
nanocomposite material was used as ethanol sensor at low
temperatures. The composite sensitivity for ethanol has increased by
a factor of 2 at room temperature and by a factor of 13 at 250°C in
comparison to that of pure SnO2. SEM image of nanocomposite
material showed MWNTs were embedded in SnO2 matrix and also a
higher surface area was observed in the presence of functionalized
MWNTs. Greatly improved sensitivity of the composite material to
ethanol can be attributed to new gas accessing passes through
MWNTs and higher specific surface area.
Abstract: In the present work, we have developed a symmetric electrochemical capacitor based on the nanostructured iron oxide (Fe3O4)-activated carbon (AC) nanocomposite materials. The physical properties of the nanocomposites were characterized by Scanning Electron Microscopy (SEM) and Brunauer-Emmett-Teller (BET) analysis. The electrochemical performances of the composite electrode in 1.0 M Na2SO3 and 1.0 M Na2SO4 aqueous solutions were evaluated using cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The composite electrode with 4 wt% of iron oxide nanomaterials exhibits the highest capacitance of 86 F/g. The experimental results clearly indicate that the incorporation of iron oxide nanomaterials at low concentration to the composite can improve the capacitive performance, mainly attributed to the contribution of the pseudocapacitance charge storage mechanism and the enhancement on the effective surface area of the electrode. Nevertheless, there is an optimum threshold on the amount of iron oxide that needs to be incorporated into the composite system. When this optimum threshold is exceeded, the capacitive performance of the electrode starts to deteriorate, as a result of the undesired particle aggregation, which is clearly indicated in the SEM analysis. The electrochemical performance of the composite electrode is found to be superior when Na2SO3 is used as the electrolyte, if compared to the Na2SO4 solution. It is believed that Fe3O4 nanoparticles can provide favourable surface adsorption sites for sulphite (SO3 2-) anions which act as catalysts for subsequent redox and intercalation reactions.
Abstract: The aim of this work is to investigate on the internalflow
patterns in a plate heat exchanger channel, which affect the
rate of sedimentation fouling on the heat transfer surface of the
plate heat exchanger. The research methodologies were the
computer simulation using Computational Fluid Dynamics (CFD)
and the experimental works. COMSOL MULTIPHYSICS™
Version 3.3 was used to simulate the velocity flow fields to verify
the low and high flow regions. The results from the CFD technique
were then compared with the images obtained from the
experiments in which the fouling test rig was set up with a singlechannel
plate heat exchanger to monitor the fouling of calcium
carbonate. Two parameters were varied i.e., the crossing angle of
the two plate: 55/55, 10/10, and 55/10 degree, and the fluid flow
rate at the inlet: 0.0566, 0.1132 and 0.1698 m/s. The type of plate
“GX-12" (the surface area 0.12 m2, the depth 2.9 mm, the width of
fluid flow 215 mm and the thickness of stainless plate of 0.5 mm)
was used in this study. The results indicated that the velocity
distribution for the case of 55/55 degree seems to be very well
organized when compared with the others. Also, an increase in the
inlet velocity resulted in the reduction of fouling rate on the surface
of plate heat exchangers.
Abstract: In this study, a low temperature sensor highly selective to CO in presence of methane is fabricated by using 4 nm SnO2 quantum dots (QDs) prepared by sonication assisted precipitation. SnCl4 aqueous solution was precipitated by ammonia under sonication, which continued for 2 h. A part of the sample was then dried and calcined at 400°C for 1.5 h and characterized by XRD and BET. The average particle size and the specific surface area of the SnO2 QDs as well as their sensing properties were compared with the SnO2 nano-particles which were prepared by conventional sol-gel method. The BET surface area of sonochemically as-prepared product and the one calcined at 400°C after 1.5 hr are 257 m2/gr and 212 m2/gr respectively while the specific surface area for SnO2 nanoparticles prepared by conventional sol-gel method is about 80m2/gr. XRD spectra revealed pure crystalline phase of SnO2 is formed for both as-prepared and calcined samples of SnO2 QDs. However, for the sample prepared by sol-gel method and calcined at 400°C SnO crystals are detected along with those of SnO2. Quantum dots of SnO2 show exceedingly high sensitivity to CO with different concentrations of 100, 300 and 1000 ppm in whole range of temperature (25- 350°C). At 50°C a sensitivity of 27 was obtained for 1000 ppm CO, which increases to a maximum of 147 when the temperature rises to 225°C and then drops off while the maximum sensitivity for the SnO2 sample prepared by the sol-gel method was obtained at 300°C with the amount of 47.2. At the same time no sensitivity to methane is observed in whole range of temperatures for SnO2 QDs. The response and recovery times of the sensor sharply decreases with temperature, while the high selectivity to CO does not deteriorate.
Abstract: Deoxygenation of beef fat for the production of hydrogenated biodiesel is investigated in a high pressure continuous flow fixed bed reactor over palladium-supported mesoporous titania catalyst synthesized via a combined single-step sol-gel process with surfactant-assisted templating method (SATM). The catalyst possessed a mesoporous charactheristic with high surface area and narrow pore size distribution. The main products of all Pd/TiO2 catalysts are n-heptadecane (n-C17) and n-pentadecane (n-C15) resulting from decarbonylation reaction. Pd/TiO2 catalyst synthesized via a combined single-step sol-gel process with SATM (SSSG) gave higher activity and selectivity to the desired products when compared to IWI/SG-TiO2 and IWI/P25-TiO2, respectively. SSSG catalyst gave the average conversion up to 80-90 % and 80 % for the selectivity in diesel range hydrocarbons. This result may cause by the higher surface area and the ability in dispersion of palladium ion in mesoporous of TiO2 during sol-gel process.
Abstract: Performance of a cobalt doped sol-gel derived silica (Co/SiO2) catalyst for Fischer–Tropsch synthesis (FTS) in slurryphase reactor was studied using paraffin wax as initial liquid media. The reactive mixed gas, hydrogen (H2) and carbon monoxide (CO) in a molar ratio of 2:1, was flowed at 50 ml/min. Braunauer-Emmett- Teller (BET) surface area and X-ray diffraction (XRD) techniques were employed to characterize both the specific surface area and crystallinity of the catalyst, respectively. The reduction behavior of Co/SiO2 catalyst was investigated using the Temperature Programmmed Reduction (TPR) method. Operating temperatures were varied from 493 to 533K to find the optimum conditions to maximize liquid fuels production, gasoline and diesel.