Abstract: With rapid technology scaling, the proportion of the
static power consumption catches up with dynamic power
consumption gradually. To decrease leakage consumption is
becoming more and more important in low-power design. This paper
presents a power-gating scheme for P-DTGAL (p-type dual
transmission gate adiabatic logic) circuits to reduce leakage power
dissipations under deep submicron process. The energy dissipations of
P-DTGAL circuits with power-gating scheme are investigated in
different processes, frequencies and active ratios. BSIM4 model is
adopted to reflect the characteristics of the leakage currents. HSPICE
simulations show that the leakage loss is greatly reduced by using the
P-DTGAL with power-gating techniques.
Abstract: The resistive-inductive-capacitive behavior of long
interconnects which are driven by CMOS gates are presented in this
paper. The analysis is based on the ¤Ç-model of a RLC load and is
developed for submicron devices. Accurate and analytical
expressions for the output load voltage, the propagation delay and the
short circuit power dissipation have been proposed after solving a
system of differential equations which accurately describe the
behavior of the circuit. The effect of coupling capacitance between
input and output and the short circuit current on these performance
parameters are also incorporated in the proposed model. The
estimated proposed delay and short circuit power dissipation are in
very good agreement with the SPICE simulation with average
relative error less than 6%.
Abstract: A active inductor in CMOS techonology with a supply voltage of 1.8V is presented. The value of the inductance L can be in the range from 0.12nH to 0.25nH in high frequency(HF). The proposed active inductor is designed in TSMC 0.18-um CMOS technology. The power dissipation of this inductor can retain constant at all operating frequency bands and consume around 20mW from 1.8V power supply. Inductors designed by integrated circuit occupy much smaller area, for this reason,attracted researchers attention for more than decade. In this design we used Advanced Designed System (ADS) for simulating cicuit.
Abstract: In this paper zero-dissipative explicit Runge-Kutta
method is derived for solving second-order ordinary differential
equations with periodical solutions. The phase-lag and dissipation
properties for Runge-Kutta (RK) method are also discussed. The new
method has algebraic order three with dissipation of order infinity.
The numerical results for the new method are compared with existing
method when solving the second-order differential equations with
periodic solutions using constant step size.
Abstract: Thermal behavior of fuel channel under loss of coolant accident (LOCA) is a major concern for nuclear reactor safety. LOCA along with failure of emergency cooling water system (ECC) may leads to mechanical deformations like sagging and ballooning. In order to understand the phenomenon an experiment has been carried out using 19 pin fuel element simulator. Main purpose of the experiment was to trace temperature profiles over the pressure tube, calandria tube and clad tubes of Indian Pressurized Heavy Water Reactor (IPHWR) under symmetrical and asymmetrical heat-up conditions. For simulating the fully voided scenario, symmetrical heating of pressure was carried out by injecting 13.2 KW (2 % of nominal power) to all the 19 pins and the temperatures of pressure tube, calandria tube and clad tubes were measured. During symmetrical heating the sagging of fuel channel was initiated at 460 °C and the highest temperature attained by PT was 650 °C . The decay heat from clad tubes was dissipated to moderator mainly by radiation and natural convection. The highest temperature of 680 °C was observed over the outer ring of clad tubes of fuel simulator. Again, to simulate partially voided condition, asymmetrical heating of pressure was carried out by supplying 8.0 kW power to upper 8 pins of fuel simulator and temperature profiles were measured. Along the circumference of pressure tube (PT) the highest temperature difference of 320 °C was observed, which highlights the magnitude of thermal stresses under partially voided conditions.
Abstract: We developed a GPS-based navigation device for the
blind, with audio guidance in Thai language. The device is composed
of simple and inexpensive hardware components. Its user interface is
quite simple. It determines optimal routes to various landmarks in our
university campus by using heuristic search for the next waypoints.
We tested the device and made note of its limitations and possible
extensions.
Abstract: Although silicon photonic devices provide a significantly larger bandwidth and dissipate a substantially less power than the electronic devices, they suffer from a large size due to the fundamental diffraction limit and the weak optical response of Si. A potential solution is to exploit Si plasmonics, which may not only miniaturize the photonic device far beyond the diffraction limit, but also enhance the optical response in Si due to the electromagnetic field confinement. In this paper, we discuss and summarize the recently developed metal-insulator-Si-insulator-metal nanoplasmonic waveguide as well as various passive and active plasmonic components based on this waveguide, including coupler, bend, power splitter, ring resonator, MZI, modulator, detector, etc. All these plasmonic components are CMOS compatible and could be integrated with electronic and conventional dielectric photonic devices on the same SOI chip. More potential plasmonic devices as well as plasmonic nanocircuits with complex functionalities are also addressed.
Abstract: With respect to the dissipation of energy through
plastic deformation of joints of prefabricated wall units, the paper
points out the principal importance of efficient reinforcement of the
prefabricated system at its joints. The method, quality and amount of
reinforcement are essential for reaching the necessary degree of joint
ductility. The paper presents partial results of experimental research
of vertical joints of prefabricated units exposed to monotonously
rising loading and repetitive shear force and formulates a conclusion
that the limit state of the structure as a whole is preceded by the
disintegration of joints, or that the structure tends to pass from
linearly elastic behaviour to non-linearly elastic to plastic behaviour
by exceeding the proportional elastic limit in joints.Experimental
verification on a model of a 7-storey prefabricated structure revealed
weak points in its load-bearing systems, mainly at places of critical
points around openings situated in close proximity to vertical joints
of mutually perpendicularly oriented walls.
Abstract: In this paper, a theoretical formula is presented to
predict the instantaneous folding force of the first fold creation in a
square column under axial loading. Calculations are based on analysis
of “Basic Folding Mechanism" introduced by Wierzbicki and
Abramowicz. For this purpose, the sum of dissipated energy rate under
bending around horizontal and inclined hinge lines and dissipated
energy rate under extensional deformations are equated to the work rate
of the external force on the structure. Final formula obtained in this
research, reasonably predicts the instantaneous folding force of the first
fold creation versus folding distance and folding angle and also predicts
the instantaneous folding force instead of the average value. Finally,
according to the calculated theoretical relation, instantaneous folding
force of the first fold creation in a square column was sketched
versus folding distance and was compared to the experimental results
which showed a good correlation.
Abstract: There is need to explore emerging technologies based on carbon nanotube electronics as the MOS technology is approaching its limits. As MOS devices scale to the nano ranges, increased short channel effects and process variations considerably effect device and circuit designs. As a promising new transistor, the Carbon Nanotube Field Effect Transistor(CNTFET) avoids most of the fundamental limitations of the Traditional MOSFET devices. In this paper we present the analysis and comparision of a Carbon Nanotube FET(CNTFET) based 10(A current mirror with MOSFET for 32nm technology node. The comparision shows the superiority of the former in terms of 97% increase in output resistance,24% decrease in power dissipation and 40% decrease in minimum voltage required for constant saturation current. Furthermore the effect on performance of current mirror due to change in chirality vector of CNT has also been investigated. The circuit simulations are carried out using HSPICE model.
Abstract: Considering the merits and limitations of energy dissipation system, seismic isolation system and suspension system, a new earthquake resistant system is proposed and is demonstrated numerically through a frame-core structure. Base isolators and story isolators are installed in the proposed system. The former “isolates" the frame from the foundation and the latter “separates" the frame from the center core. Equations of motion are formulated to study the response of the proposed structural system to strong earthquake motion. As compared with the fixed-base building system, the proposed structural system shows substantial reduction on structural response.
Abstract: The bypass exhaust system of a 160 MW combined cycle has been modeled and analyzed using numerical simulation in 2D prospective. Analysis was carried out using the commercial numerical simulation software, FLUENT 6.2. All inputs were based on the technical data gathered from working conditions of a Siemens V94.2 gas turbine, installed in the Yazd power plant. This paper deals with reduction of pressure drop in bypass exhaust system using turning vanes mounted in diverter box in order to alleviate turbulent energy dissipation rate above diverter box. The geometry of such turning vanes has been optimized based on the flow pattern at diverter box inlet. The results show that the use of optimized turning vanes in diverter box can improve the flow pattern and eliminate vortices around sharp edges just before the silencer. Furthermore, this optimization could decrease the pressure drop in bypass exhaust system and leads to higher plant efficiency.
Abstract: Heat pipes are used to control the thermal problem for
electronic cooling. It is especially difficult to dissipate heat to a heat
sink in an environment in space compared to earth. For solving this
problem, in this study, the Poiseuille (Po) number, which is the main
measure of the performance of a heat pipe, is studied by CFD; then, the
heat pipe performance is verified with experimental results. A heat
pipe is then fabricated for a spatial environment, and an in-house code
is developed. Further, a heat pipe subsystem, which consists of a heat
pipe, MLI (Multi Layer Insulator), SSM (Second Surface Mirror), and
radiator, is tested and correlated with the TMM (Thermal
Mathematical Model) through a commercial code. The correlation
results satisfy the 3K requirement, and the generated thermal model is
verified for application to a spatial environment.
Abstract: The more recent satellite projects/programs makes
extensive usage of real – time embedded systems. 16 bit processors
which meet the Mil-Std-1750 standard architecture have been used in
on-board systems. Most of the Space Applications have been written
in ADA. From a futuristic point of view, 32 bit/ 64 bit processors are
needed in the area of spacecraft computing and therefore an effort is
desirable in the study and survey of 64 bit architectures for space
applications. This will also result in significant technology
development in terms of VLSI and software tools for ADA (as the
legacy code is in ADA).
There are several basic requirements for a special processor for
this purpose. They include Radiation Hardened (RadHard) devices,
very low power dissipation, compatibility with existing operational
systems, scalable architectures for higher computational needs,
reliability, higher memory and I/O bandwidth, predictability, realtime
operating system and manufacturability of such processors.
Further on, these may include selection of FPGA devices, selection
of EDA tool chains, design flow, partitioning of the design, pin
count, performance evaluation, timing analysis etc.
This project deals with a brief study of 32 and 64 bit processors
readily available in the market and designing/ fabricating a 64 bit
RISC processor named RISC MicroProcessor with added
functionalities of an extended double precision floating point unit
and a 32 bit signal processing unit acting as co-processors. In this
paper, we emphasize the ease and importance of using Open Core
(OpenSparc T1 Verilog RTL) and Open “Source" EDA tools such as
Icarus to develop FPGA based prototypes quickly. Commercial tools
such as Xilinx ISE for Synthesis are also used when appropriate.
Abstract: In recent past, the Unified Modeling Language (UML) has become the de facto industry standard for object-oriented modeling of the software systems. The syntax and semantics rich UML has encouraged industry to develop several supporting tools including those capable of generating deployable product (code) from the UML models. As a consequence, ensuring the correctness of the model/design has become challenging and extremely important task. In this paper, we present an approach for automatic verification of protocol model/design. As a case study, Session Initiation Protocol (SIP) design is verified for the property, “the CALLER will not converse with the CALLEE before the connection is established between them ". The SIP is modeled using UML statechart diagrams and the desired properties are expressed in temporal logic. Our prototype verifier “UML-SMV" is used to carry out the verification. We subjected an erroneous SIP model to the UML-SMV, the verifier could successfully detect the error (in 76.26ms) and generate the error trace.
Abstract: A new nonlinear PID controller and its stability
analysis are presented in this paper. A nonlinear function is deduced
from the similarities between the control effort and the electric-field
effect of a capacitor. The conventional linear PID controller can be
modified into a nonlinear one by this function. To analyze the stability
of the nonlinear PID controlled system, an idea of energy equivalence
is adapted to avoid the conservativeness which is usually arisen from
some traditional theorems and Criterions. The energy equivalence is
naturally related with the conceptions of Passivity and T-Passivity. As
a result, an engineering guideline for the parameter design of the
nonlinear PID controller is obtained. An inverted pendulum system is
tested to verify the nonlinear PID control scheme.
Abstract: This study investigates the capacity of granular
activated carbon (GAC) for the storage of methane through the
equilibrium adsorption. An experimental apparatus consist of a dual
adsorption vessel was set up for the measurement of equilibrium
adsorption of methane on GAC using volumetric technique (pressure
decay). Experimental isotherms of methane adsorption were
determined by the measurement of equilibrium uptake of methane in
different pressures (0-50 bar) and temperatures (285.15-328.15°K).
The experimental data was fitted to Freundlich and Langmuir
equations to determine the model isotherm. The results show that the
experimental data is equally well fitted by the both model isotherms.
Using the experimental data obtained in different temperatures the
isosteric heat of methane adsorption was also calculated by the
Clausius-Clapeyron equation from the Sips isotherm model. Results
of isosteric heat of adsorption show that decreasing temperature or
increasing methane uptake by GAC decrease the isosteric heat of
methane adsorption.
Abstract: In this paper, we propose an energy efficient cluster
based communication protocol for wireless sensor network. Our
protocol considers both the residual energy of sensor nodes and the
distance of each node from the BS when selecting cluster-head. This
protocol can successfully prolong the network-s lifetime by 1)
reducing the total energy dissipation on the network and 2) evenly
distributing energy consumption over all sensor nodes. In this
protocol, the nodes with more energy and less distance from the BS
are probable to be selected as cluster-head. Simulation results with
MATLAB show that proposed protocol could increase the lifetime of
network more than 94% for first node die (FND), and more than 6%
for the half of the nodes alive (HNA) factor as compared with
conventional protocols.
Abstract: Today, the Internet based communication has widen
the opportunity of event monitoring system in the medical field.
There is always a need of analyzing and designing secure and reliable
mobile communication between the hospital and biomedical
engineers mobile units. This study has been carried out to find
possible solution using SIP-based event notification for alerting the
technical staff about the Biomedical Device (BMD) status and
Patients treatment session. The Session Initiation Protocol (SIP) can
be used to create a medical event notification system. SIP can work
on a variety of devices. Its adoption as the protocol of choice for third
generation wireless networks allows for a robust and scalable
environment. One of the advantages of SIP is that it supports personal
mobility through the separation of user addressing and device
addressing. The solution for Telemed alert notification system is
based on SIP - Specific Event Notification. The aim of this project is
to extend mobility service to the hospital technicians who are using
Telemedicine system.
Abstract: This study aims to demonstrate the quantification of
peptides based on isotope dilution surface enhanced Raman
scattering (IDSERS). SERS spectra of phenylalanine (Phe), leucine
(Leu) and two peptide sequences TGQIFK (T13) and
YSFLQNPQTSLCFSESIPTPSNR (T6) as part of the 22-kDa
human growth hormone (hGH) were obtained on Ag-nanoparticle
covered substrates. On the basis of the dominant Phe and Leu
vibrational modes, precise partial least squares (PLS) prediction
models were built enabling the determination of unknown T13 and
T6 concentrations. Detection of hGH in its physiological
concentration in order to investigate the possibility of protein
quantification has been achieved.