Abstract: During the last decade Panicum virgatum, known as
Switchgrass, has been broadly studied because of its remarkable
attributes as a substitute pasture and as a functional biofuel source.
The objective of this investigation was to establish soil suitability for
Switchgrass in the State of Mississippi. A linear weighted additive
model was developed to forecast soil suitability. Multicriteria
analysis and Sensitivity analysis were utilized to adjust and optimize
the model. The model was fit using seven years of field data
associated with soils characteristics collected from Natural Resources
Conservation System - United States Department of Agriculture
(NRCS-USDA). The best model was selected by correlating
calculated biomass yield with each model's soils-based output for
Switchgrass suitability. Coefficient of determination (r2) was the
decisive factor used to establish the 'best' soil suitability model.
Coefficients associated with the 'best' model were implemented
within a Geographic Information System (GIS) to create a map of
relative soil suitability for Switchgrass in Mississippi. A Geodatabase
associated with soil parameters was built and is available for future
Geographic Information System use.
Abstract: The paper discuses the effect of initial stresses on the reflection coefficients of plane waves in a dissipative medium. Basic governing equations are formulated in context of Biot's incremental deformation theory. These governing equations are solved analytically to obtain the dimensional phase velocities of plane waves propagating in plane of symmetry. Closed-form expressions for the reflection coefficients of P and SV waves- incident at the free surface of an initially stressed dissipative medium are obtained. Numerical computations, using these expressions, are carried out for a particular model. Computations made with the results predicted in presence and absence of the initial stresses and the results have been shown graphically. The study shows that the presence of compressive initial stresses increases the velocity of longitudinal wave (P-wave) but diminishes that of transverse wave (SV-wave). Also the numerical results presented indicate that initial stresses and dissipation might affect the reflection coefficients significantly.
Abstract: This paper describes a low-power second-order filter
for a continuous-time chopper stabilized capacitive sensor interface,
integrated with a fully differential post-CMOS surface-micromachined
MEMS pressure sensor. The circuit uses a single-ended
folded-cascode operational amplifier and two GM-C filters connected
in cascade. The circuit is realized in a 0.18 μm CMOS process and
offers differential to single-ended conversion. The novelty of the
scheme is the cascade of two GM-C filters to achieve a second-order
filter while minimizing power dissipation. The simulated filter cutoff
frequency is 1.14 kHz at common-mode voltage 1.65 V,
operating from a 3.3 V supply while dissipating 172μW of power.
The filter achieves an operating range of 1V for an output load of
1MOhm and 10pF.
Abstract: In this paper, the dam-reservoir interaction is
analyzed using a finite element approach. The fluid is assumed to be
incompressible, irrotational and inviscid. The assumed boundary
conditions are that the interface of the dam and reservoir is vertical
and the bottom of reservoir is rigid and horizontal. The governing
equation for these boundary conditions is implemented in the
developed finite element code considering the horizontal and vertical
earthquake components. The weighted residual standard Galerkin
finite element technique with 8-node elements is used to discretize
the equation that produces a symmetric matrix equation for the damreservoir
system. A new boundary condition is proposed for
truncating surface of unbounded fluid domain to show the energy
dissipation in the reservoir, through radiation in the infinite upstream
direction. The Sommerfeld-s and perfect damping boundary
conditions are also implemented for a truncated boundary to compare
with the proposed far end boundary. The results are compared with
an analytical solution to demonstrate the accuracy of the proposed
formulation and other truncated boundary conditions in modeling the
hydrodynamic response of an infinite reservoir.
Abstract: This article is dedicated to development of
mathematical models for determining the dynamics of
concentration of hazardous substances in urban turbulent
atmosphere. Development of the mathematical models implied
taking into account the time-space variability of the fields of
meteorological items and such turbulent atmosphere data as vortex
nature, nonlinear nature, dissipativity and diffusivity. Knowing the
turbulent airflow velocity is not assumed when developing the
model. However, a simplified model implies that the turbulent and
molecular diffusion ratio is a piecewise constant function that
changes depending on vertical distance from the earth surface.
Thereby an important assumption of vertical stratification of urban
air due to atmospheric accumulation of hazardous substances
emitted by motor vehicles is introduced into the mathematical
model. The suggested simplified non-linear mathematical model of
determining the sought exhaust concentration at a priori unknown
turbulent flow velocity through non-degenerate transformation is
reduced to the model which is subsequently solved analytically.
Abstract: Application-Specific Instruction (ASI ) set Processors
(ASIP) have become an important design choice for embedded
systems due to runtime flexibility, which cannot be provided by
custom ASIC solutions. One major bottleneck in maximizing ASIP
performance is the limitation on the data bandwidth between the
General Purpose Register File (GPRF) and ASIs. This paper presents
the Implicit Registers (IRs) to provide the desirable data bandwidth.
An ASI Input/Output model is proposed to formulate the overheads of
the additional data transfer between the GPRF and IRs, therefore,
an IRs allocation algorithm is used to achieve the better performance
by minimizing the number of extra data transfer instructions. The
experiment results show an up to 3.33x speedup compared to the
results without using IRs.
Abstract: Eight difference schemes and five limiters are applied to numerical computation of Riemann problem. The resolution of discontinuities of each scheme produced is compared. Numerical dissipation and its estimation are discussed. The result shows that the numerical dissipation of each scheme is vital to improve scheme-s accuracy and stability. MUSCL methodology is an effective approach to increase computational efficiency and resolution. Limiter should be selected appropriately by balancing compressive and diffusive performance.
Abstract: The general purpose processors that are used in
embedded systems must support constraints like execution time,
power consumption, code size and so on. On the other hand an
Application Specific Instruction-set Processor (ASIP) has advantages
in terms of power consumption, performance and flexibility. In this
paper, a 16-bit Application Specific Instruction-set processor for the
sensor data transfer is proposed. The designed processor architecture
consists of on-chip transmitter and receiver modules along with the
processing and controlling units to enable the data transmission and
reception on a single die. The data transfer is accomplished with less
number of instructions as compared with the general purpose
processor. The ASIP core operates at a maximum clock frequency of
1.132GHz with a delay of 0.883ns and consumes 569.63mW power
at an operating voltage of 1.2V. The ASIP is implemented in Verilog
HDL using the Xilinx platform on Virtex4.
Abstract: Data gathering is an essential operation in wireless
sensor network applications. So it requires energy efficiency
techniques to increase the lifetime of the network. Similarly,
clustering is also an effective technique to improve the energy
efficiency and network lifetime of wireless sensor networks. In this
paper, an energy efficient cluster formation protocol is proposed with
the objective of achieving low energy dissipation and latency without
sacrificing application specific quality. The objective is achieved by
applying randomized, adaptive, self-configuring cluster formation
and localized control for data transfers. It involves application -
specific data processing, such as data aggregation or compression.
The cluster formation algorithm allows each node to make
independent decisions, so as to generate good clusters as the end.
Simulation results show that the proposed protocol utilizes minimum
energy and latency for cluster formation, there by reducing the
overhead of the protocol.
Abstract: The knee bracing steel frame (KBF) is a new kind of energy dissipating frame, which combines excellent ductility and lateral stiffness. In this framing system, a special form of diagonal brace connected to a knee element instead of beam-column joint, is investigated. Recently, a similar system was proposed and named as chevron knee bracing system (CKB) which in comparison with the former system has a better energy absorption characteristic and at the same time retains the elastic nature of the structures. Knee bracing can provide a stiffer bracing system but reduces the ductility of the steel frame. Chevron knee bracing can be employed to provide the desired ductility level for a design. In this article, relation between seismic performance and structural parameters of the two above mentioned systems are investigated and compared. Frames with similar dimensions but various heights in both systems are designed according to Iranian code of practice for seismic resistant design of building, and then based on a non-linear push over static analysis; the seismic parameters such as behavior factor and performance levels are compared.
Abstract: This paper presents two different sequential switching hybrid-modulation strategies and implemented for cascaded multilevel inverters. Hybrid modulation strategies represent the combinations of Fundamental-frequency pulse width modulation (FFPWM) and Multilevel sinusoidal-modulation (MSPWM) strategies, and are designed for performance of the well-known Alternative Phase opposition disposition (APOD), Phase shifted carrier (PSC). The main characteristics of these modulations are the reduction of switching losses with good harmonic performance, balanced power loss dissipation among the devices with in a cell, and among the series-connected cells. The feasibility of these modulations is verified through spectral analysis, power loss analysis and simulation.
Abstract: In this study, an analysis has been performed for
free convection with radiation effect over a thermal forming
nonlinearly stretching sheet. Parameters n, k0, Pr, G represent
the dominance of the nonlinearly effect, radiation effect, heat
transfer and free convection effects which have been presented
in governing equations, respectively. The similarity
transformation and the finite-difference methods have been
used to analyze the present problem. From the results, we find
that the effects of parameters n, k0, Pr, Ec and G to the
nonlinearly stretching sheet. The increase of Prandtl number Pr,
free convection parameter G or radiation parameter k0 resulting
in the increase of heat transfer effects, but increase of the
viscous dissipation number Ec will decrease of heat transfer
effect.
Abstract: Ion-acoustic solitary and shock waves in dense
quantum plasmas whose constituents are electrons, positrons, and
positive ions are investigated. We assume that ion velocity is weakly
relativistic and also the effects of kinematic viscosity among the
plasma constituents is considered. By using the reductive
perturbation method, the Korteweg–deVries–Burger (KdV-B)
equation is derived.
Abstract: The issue of real-time and reliable report delivery is extremely important for taking effective decision in a real world mission critical Wireless Sensor Network (WSN) based application. The sensor data behaves differently in many ways from the data in traditional databases. WSNs need a mechanism to register, process queries, and disseminate data. In this paper we propose an architectural framework for data placement and management. We propose a reliable and real time approach for data placement and achieving data integrity using self organized sensor clusters. Instead of storing information in individual cluster heads as suggested in some protocols, in our architecture we suggest storing of information of all clusters within a cell in the corresponding base station. For data dissemination and action in the wireless sensor network we propose to use Action and Relay Stations (ARS). To reduce average energy dissipation of sensor nodes, the data is sent to the nearest ARS rather than base station. We have designed our architecture in such a way so as to achieve greater energy savings, enhanced availability and reliability.
Abstract: SIP (Session Initiation Protocol), using HTML based
call control messaging which is quite simple and efficient, is being
replaced for VoIP networks recently. As for authentication and
authorization purposes there are many approaches and considerations
for securing SIP to eliminate forgery on the integrity of SIP
messages. On the other hand Elliptic Curve Cryptography has
significant advantages like smaller key sizes, faster computations on
behalf of other Public Key Cryptography (PKC) systems that obtain
data transmission more secure and efficient. In this work a new
approach is proposed for secure SIP authentication by using a public
key exchange mechanism using ECC. Total execution times and
memory requirements of proposed scheme have been improved in
comparison with non-elliptic approaches by adopting elliptic-based
key exchange mechanism.
Abstract: The stilling basins are commonly used to dissipate the
energy and protect the downstream floor from erosion. The aim of
the present experimental work is to improve the roughened stilling
basin using T-shape roughness instead of the regular cubic one and
design this new shape. As a result of the present work the best
intensity and the best roughness length are identified. Also, it is
found that the T-shape roughness save materials and reduce the jump
length compared to the cubic one. Sensitivity analysis was performed
and it was noticed that the change in the length of jump is more
sensitive to the change in roughness length than the change in
intensity.
Abstract: This paper describes the development of a numerical finite element algorithm used for the analysis of reinforced concrete structure equipped with shakes energy absorbing device subjected to earthquake excitation. For this purpose a finite element program code for analysis of reinforced concrete frame buildings is developed. The performance of developed program code is evaluated by analyzing of a reinforced concrete frame buildings model. The results are show that using damper device as seismic energy dissipation system effectively can reduce the structural response of framed structure during earthquake occurrence.
Abstract: The results show that the bridge equipped with seismic isolation bearing system shows a high amount of energy dissipation. The purpose of the present study is to analyze the overall performance of continuous curved highway viaducts with different bearing supports, with an emphasis on the effectiveness of seismic isolation based on lead rubber bearing and hedge reaction force bearing system consisted of friction sliding bearing and rubber bearing. The bridge seismic performance has been evaluated on six different cases with six bearing models. The effects of the different arrangement of bearing on the deck superstructure displacements, the seismic damage at the bottom of the piers, movement track at the pier-s top and the total and strain energies absorbed by the structure are evaluated. In conclusion, the results provide sufficient evidence of the effectiveness on the use of seismic isolation on steel curved highway bridges.
Abstract: An experimental study is realized in order to verify the
Mini Heat Pipe (MHP) concept for cooling high power dissipation
electronic components and determines the potential advantages of
constructing mini channels as an integrated part of a flat heat pipe. A
Flat Mini Heat Pipe (FMHP) prototype including a capillary structure
composed of parallel rectangular microchannels is manufactured and
a filling apparatus is developed in order to charge the FMHP. The
heat transfer improvement obtained by comparing the heat pipe
thermal resistance to the heat conduction thermal resistance of a
copper plate having the same dimensions as the tested FMHP is
demonstrated for different heat input flux rates. Moreover, the heat
transfer in the evaporator and condenser sections are analyzed, and
heat transfer laws are proposed. In the theoretical part of this work, a
detailed mathematical model of a FMHP with axial microchannels is
developed in which the fluid flow is considered along with the heat
and mass transfer processes during evaporation and condensation.
The model is based on the equations for the mass, momentum and
energy conservation, which are written for the evaporator, adiabatic,
and condenser zones. The model, which permits to simulate several
shapes of microchannels, can predict the maximum heat transfer
capacity of FMHP, the optimal fluid mass, and the flow and thermal
parameters along the FMHP. The comparison between experimental
and model results shows the good ability of the numerical model to
predict the axial temperature distribution along the FMHP.
Abstract: The Internet telephony employs a new type of Internet communication on which a mutual communication is realized by establishing sessions. Session Initiation Protocol (SIP) is used to establish sessions between end-users. For unreliable transmission (UDP), SIP message should be retransmitted when it is lost. The retransmissions increase a load of the SIP signaling network, and sometimes lead to performance degradation when a network is overloaded. The paper proposes an overload control for a SIP signaling network to protect from a performance degradation. Introducing two thresholds in a queue of a SIP proxy server, the SIP proxy server detects a congestion. Once congestion is detected, a SIP signaling network restricts to make new calls. The proposed overload control is evaluated using the network simulator (ns-2). With simulation results, the paper shows the proposed overload control works well.