Abstract: The postharvest quality management of tomatoes is
important to limit the amount of losses that occur due to deterioration
between harvest and consumption. This study was undertaken to
investigate the effects of pre- and postharvest integrated agrotechnologies,
involving greenhouse microclimate and postharvest
storage conditions, on the postharvest quality attributes of four
tomato cultivars. Tomato fruit firmness, colour (hue angle (h°) and
L* value), pH and total soluble solids for the cultivars Bona,
Star 9037, Star 9009 and Zeal, grown in a fan-pad evaporativelycooled
and an open-ended naturally-ventilated tunnel, were harvested
at the mature-green stage. The tomatoes were stored for 28 days
under cold storage conditions, with a temperature of 13°C and RH of
85%, and under ambient air conditions, with a temperature of 23±
2°C and RH of 52± 4%. This study has provided information on the
effect of integrated pre-harvest and postharvest agro-technologies,
involving greenhouse microclimate and postharvest storage
environment on the postharvest quality attributes of four of the
tomato cultivars in South Africa. NVT-grown tomatoes retained
better textural qualities, but ripened faster by changing from green to
red faster, although these were reduced under cold storage conditions.
FPVT-grown tomatoes had lower firmness, but ripened slowly with
higher colour attributes. With cold storage conditions, the firmness of
FPVT-grown tomatoes was maintained. Cultivar Bona firmness and
colour qualities depreciated the fastest, but it had higher TSS content
and lower pH values. Star 9009 and Star 9037 presented better
quality, by retaining higher firmness and ripening slowly, but they
had the lowest TSS contents and high pH values, especially
Star 9037. Cold storage improved the firmness of tomato cultivars
with poor textural quality and faster colour changes.
Abstract: This study focuses on the cooling of a photovoltaic
panel (PV). Indeed, the cooling improves the conversion capacity of
this one and maintains, under extreme conditions of air temperature,
the panel temperature at an appreciable level which avoids the
altering. To do this, a fan provides forced circulation of air. Because
the fan is supplied by the panel, it is necessary to determine the
optimum operating point that unites efficiency of the PV with the
consumption of the fan. For this matter, numerical simulations are
performed at varying mass flow rates of air, under two extreme air
temperatures (50°C, 25°C) and a fixed solar radiation (1000W.m2) in
a case of no wind.
Abstract: Strontium hexaferrite (SrFe12O19; Sr-ferrite) is one of
the well-known materials for permanent magnets. In this study, Mtype
strontium ferrite was prepared by following the conventional
ceramic method from steelmaking by-product. Initial materials;
SrCO3 and by-product, were mixed together in the composition of
SrFe12O19 in different Sr/Fe ratios. The mixtures of these raw
materials were dry-milled for 6h. The blended powder was presintered
(i.e. calcination) at 1000°C for different times periods, then
cooled down to room temperature. These pre-sintered samples were
re-milled in a dry atmosphere for 1h and then fired at different
temperatures in atmospheric conditions, and cooled down to room
temperature. The produced magnetic powder has a dense hexagonal
grain shape structure. The calculated energy product values for the
produced samples ranged from 0.3 to 2.4 MGOe.
Abstract: The aim of this study was to analyze selected quality characteristics of cooked pork sausages manufactured with the addition of Sea buckthorn (Hippophae rhamnoides L.) berries preparations. Stuffings of model sausages consisted of pork, backfat, water and additives such a curing salt and sodium isoascorbate. Functional additives used in production process were two preparations obtained from dried Sea buckthorn berries in form of powder and brew. Powder of dried berries was added in amount of 1 and 3 g, while water infusion as a replacement of 50 and 100% ice water included in meat products formula. Control samples were produced without functional additives. Experimental stuffings were heat treated in water bath and stored for 4 weeks under cooled conditions (4±1ºC). Physical parameters of colour, texture profile and technological parameters as acidity, weight losses and water activity were estimated. The effect of Sea buckthorn berries preparations on lipid oxidation during storage of final products was determine by TBARS method.
Studies have shown that addition of Sea buckthorn preparations to meat-fatty batters significant (P≤0.05) reduced the pH values of sausages samples after thermal treatment. Moreover, the addition of berries powder caused significant differences (P ≤ 0.05) in weight losses after cooking process. Analysis of results of texture profile analysis indicated, that utilization of infusion prepared from Sea buckthorn dried berries caused increase of springiness, gumminess and chewiness of final meat products. At the same time, the highest amount of Sea buckthorn berries powder in recipe caused the decrease of all measured texture parameters. Utilization of experimental preparations significantly decreased (P≤0.05) lightness (L* parameter of color) of meat products. Simultaneously, introduction of 1 and 3 grams of Sea buckthorn berries powder to meat-fatty batter increased redness (a* parameter) of samples under investigation. Higher content of substances reacting with thiobarbituric acid was observed in meat products produced without functional additives. It was observed that powder of Sea buckthorn berries added to meat-fatty batters caused higher protection against lipid oxidation in cooked sausages.
Abstract: In this work we describe the preparation of NanoSilver/methylcellulose hydrogel containing silver nanoparticles (NPs) for topical bactericidal applications. Highly concentrated dispersion of silver NPs as high as of 5g/L of silver with diameter of 10nm was prepared by reduction of AgNO3 via strong reducing agent NaBH4. Silver NPs were stabilized by addition of sodium polyacrylate in order to prevent their aggregation at such high concentration. This way synthesized silver NPs were subsequently incorporated into methylcellulose suspension at elevated temperature resulting in formation of NanoSilver/methylcellulose hydrogel when temperature cooled down to laboratory conditions. In vitro antibacterial activity assay proved high bactericidal and fungicidal efficiency of silver NPs alone in the form of dispersion as well as in the form of hydrogel against broad spectrum of bacteria and yeasts including highly multiresistant strains such as methicillin-resistant Staphylococcus aureus. A very low concentrations of silver as low as 0.84mg/L Ag in as-prepared dispersion gave antibacterial performance. NanoSilver/methylcellulose hydrogel showed antibacterial action at the lowest used silver concentration equal to 25mg/L. Such prepared NanoSilver/methylcellulose hydrogel represent promising topical antimicrobial formulation for treatment of burns and wounds.
Abstract: This paper presents a study on the effect of
second-order slip on forced convection through a long isoflux heated
or cooled planar microchannel. The fully developed solutions of flow
and thermal fields are analytically obtained on the basis of the
second-order Maxwell-Burnett slip and local heat flux boundary
conditions. Results reveal that when the average flow velocity
increases or the wall heat flux amount decreases, the role of thermal
creep becomes more insignificant, while the effect of second-order slip
becomes larger. The second-order term in the Deissler slip boundary
condition is found to contribute a positive velocity slip and then to lead
to a lower pressure drop as well as a lower temperature rise for the
heated-wall case or to a higher temperature rise for the cooled-wall
case. These findings are contrary to predictions made by the
Karniadakis slip model.
Abstract: Detailed thermal hydraulic investigations are very
essential for safe and reliable functioning of liquid metal cooled fast
breeder reactors. These investigations are further more important for
components with complex profile, since there is no direct correlation
available in literature to evaluate the hydraulic characteristics of such
components directly. In those cases available correlations for similar
profile or geometries may lead to significant uncertainty in the
outcome. Hence experimental approach can be adopted to evaluate
these hydraulic characteristics more precisely for better prediction in
reactor core components.
Prototype Fast Breeder Reactor (PFBR), a sodium cooled pool
type reactor is under advanced stage of construction at Kalpakkam,
India. Several components of this reactor core require hydraulic
investigation before its usage in the reactor. These hydraulic
investigations on full scale models, carried out by experimental
approaches using water as simulant fluid are discussed in the paper.
Abstract: This paper deals with the conceptual design of Experimental Helium Cooling Loop (EHCL) for Indian Test Blanket Module (TBM) and its related thermal hydraulic experiments. Indian TBM team is developing Lead Lithium cooled Ceramic Breeder (IN-LLCB) TBM to be tested in ITER. The TBM box structure is cooled by high pressure (8 MPa) and high temperature (300-500C) helium gas.
The first wall of TBM made of complex channel geometry having several parallel channels carrying helium gas for efficient heat extraction. Several mock-ups of these channels need to be tested before finalizing the TBM first wall design and fabrication. Besides the individual testing of such mock-ups of breeding blanket, the testing of Pb-Li to helium heat exchanger, the operational experience of helium loop and understanding of the behavior of high pressure and high temperature system components are very essential for final development of Helium Cooling System for LLCB TBM in ITER. The main requirements and characteristics of the EHCL and its conceptual design are presented in this paper.
Abstract: This paper reports on the effects of heat treatment on 3CR12 and AISI 316 stainless steel grades. Heat treatment was conducted on the steel grades and cooled using two different media; air and water in order to study the effect of each medium on the evolving properties of the samples. The heat treated samples were characterized through the evolving microstructure and hardness. It was found that there was a significant grain size reduction in both the heat treated stainless steel specimens compared to the parent materials. The finer grain sizes were achieved as a result of impediment to growth of one phase by the other. The Vickers microhardness values of the heat treated samples were higher compared to the parent materials due to the fact that each of the steel grades had a proportion of martensitic structures in their microstructures thereby improving the integrity of the material.
Abstract: Magnetohydrodynamic free convection fluid flow and heat transfer in a square cavity filled with an electric conductive fluid with Prandtl number of 0.7 has been investigated numerically. The horizontal bottom wall of the cavity was kept at Th while the side and the top walls of the cavity were maintained at a constant temperature Tc with Th>Tc. The governing equations written in terms of the primitive variables were solved numerically using the finite volume method while the SIMPLER algorithm was used to couple the velocity and pressure fields. Using the developed code, a parametric study was performed, and the effects of the Rayleigh number and the Hartman number on the fluid flow and heat transfer inside the cavity were investigated. The obtained results showed that temperature distribution and flow pattern inside the cavity depended on both strength of the magnetic field and Rayleigh number. For all cases two counter rotating eddies were formed inside the cavity. The magnetic field decreased the intensity of free convection and flow velocity. Also it was found that for higher Rayleigh numbers a relatively stronger magnetic field was needed to decrease the heat transfer through free convection.
Abstract: Numerical investigation on the generality of nanoparticle velocity equation had been done on the previous published work. The three dimensional governing equations (continuity, momentum and energy) were solved using finite volume method (FVM). Parametric study of thermal performance between pure water-cooled and nanofluid-cooled are evaluated for volume fraction in the range of 1% to 4%, and nanofluid type of gamma-Al2O3 at Reynolds number range of 67.41 to 286.77. The nanofluid is modeled using single and two phase approach. Three different existing Brownian motion velocities are applied in comparing the generality of the equation for a wide parametric condition. Deviation in between the Brownian motion velocity is identified to be due to the different means of mean free path and constant value used in diffusion equation.
Abstract: This work presents a methodology for the selection
and design of propeller oriented to the experimental verification of
theoretical results. The problem of propeller selection and design
usually present itself in the following manner: a certain air volume
and static pressure are required for a certain system. Once the
necessity of fan design on a theoretical basis has been recognized, it
is possible to determinate the dimensions for a fan unit so that it will
perform in accordance with a certain set of specifications. The same
procedures in this work then can be applied in other propeller
selection.
Abstract: Electrical discharge machining (EDM) is well
established machining technique mainly used to machine complex
geometries on difficult-to-machine materials and high strength
temperature resistant alloys. In the present research, the objective is
to study the shape of the electrode and establish the application of
liquid nitrogen in reducing distortion of the electrode during
electrical discharge machining of M2 grade high speed steel using
copper electrodes. Study of roundness was performed on the
electrode to observe the shape of the electrode for both conventional
EDM and EDM with cryogenically cooled electrode. Scanning
Electron Microscope (SEM) has been used to study the shape of
electrode tip. The effect of various parameters such as discharge
current and pulse on time has been studied to understand the behavior
of distortion of electrode. It has been concluded that the shape
retention is better in case of liquid nitrogen cooled electrode.
Abstract: In order to better understand the performance of
screen channel liquid acquisition devices (LADs) in liquid oxygen (LOX), a computational fluid dynamics (CFD) simulation of LOX passing through a LAD screen channel was conducted. In the
simulation, the screen is taken as a 'porous jump' where the pressure
drop across the screen depends on the incoming velocity and is formulated by Δp = Av + Bv2
. The CFD simulation reveals the importance of the pressure losses due to the flow entering from
across the screen and impacting and merging with the channel flow
and the vortices in the channel to the cumulative flow resistance. In fact, both the flow resistance of flows impact and mergence and the
resistance created by vortices are much larger than the friction and dynamic pressure losses in the channel and are comparable to the
flow resistance across the screen. Therefore, these resistances in the
channel must be considered as part of the evaluation for the LAD
channel performance. For proper operation of a LAD in LOX these resistances must be less than the bubble point pressure for the screen
channel in LOX. The simulation also presents the pressure and velocity distributions within the LAD screen channel, expanding the understanding of the fluid flow characteristics within the channel.
Abstract: Slag sample from copper smelting operation in a
water jacket furnace from DRC plant was used. The study intends to
determine the effect of cooling in the extraction of base metals. The
cooling methods investigated were water quenching, air cooling and
furnace cooling. The latter cooling ways were compared to the
original as received slag. It was observed that, the cooling rate of the
slag affected the leaching of base metals as it changed the phase
distribution in the slag and the base metals distribution within the
phases. It was also found that fast cooling of slag prevented
crystallization and produced an amorphous phase that encloses the
base metals. The amorphous slags from the slag dumps were more
leachable in acidic medium (HNO3) which leached 46%Cu, 95% Co,
85% Zn, 92% Pb and 79% Fe with no selectivity at pH0, than in
basic medium (NH4OH). The leachability was vice versa for the
modified slags by quenching in water which leached 89%Cu with a
high selectivity as metal extractions are less than 1% for Co, Zn, Pb
and Fe at ambient temperature and pH12. For the crystallized slags,
leaching of base metals increased with the increase of temperature
from ambient temperature to 60°C and decreased at the higher
temperature of 80°C due to the evaporation of the ammonia solution
used for basic leaching, the total amounts of base metals that were
leached in slow cooled slags were very low compared to the
quenched slag samples.
Abstract: With the long-term objective of Critical Heat Flux (CHF) prediction, a Direct Numerical Simulation (DNS) framework for simulation of subcooled and saturated nucleate pool boiling is developed. One case of saturated, and three cases of subcooled boiling at different subcooling levels are simulated. Grid refinement study is also reported. Both boiling and condensation phenomena can be computed simultaneously in the proposed numerical framework. Computed bubble detachment diameters of the saturated nucleate pool boiling cases agree well with the experiment. The flow structures around the growing bubble are presented and the accompanying physics is described. The relation between heat flux evolution from the heated wall and the bubble growth is studied, along with investigations of temperature distribution and flow field evolutions.
Abstract: The presented work is motivated by a French law
regarding nuclear waste management. A new conceptual Accelerator
Driven System (ADS) designed for the Minor Actinides (MA)
transmutation has been assessed by numerical simulation. The
MUltiple Spallation Target (MUST) ADS combines high thermal power (up to 1.4 GWth) and high specific power. A 30 mA and 1
GeV proton beam is divided into three secondary beams transmitted on three liquid lead-bismuth spallation targets. Neutron and thermalhydraulic
simulations have been performed with the code MURE, based on the Monte-Carlo transport code MCNPX. A methodology has been developed to define characteristic of the MUST ADS concept according to a specific transmutation scenario. The reference
scenario is based on a MA flux (neptunium, americium and curium)
providing from European Fast Reactor (EPR) and a plutonium multireprocessing
strategy is accounted for. The MUST ADS reference
concept is a sodium cooled fast reactor. The MA fuel at equilibrium is mixed with MgO inert matrix to limit the core reactivity and
improve the fuel thermal conductivity. The fuel is irradiated over five
years. Five years of cooling and two years for the fuel fabrication are
taken into account. The MUST ADS reference concept burns about 50% of the initial MA inventory during a complete cycle. In term of
mass, up to 570 kg/year are transmuted in one concept. The methodology to design the MUST ADS and to calculate fuel
composition at equilibrium is precisely described in the paper. A detailed fuel evolution analysis is performed and the reference scenario is compared to a scenario where only americium transmutation is performed.
Abstract: Most HWRs currently use natural uranium fuel. Using enriched uranium fuel results in a significant improvement in fuel cycle costs and uranium utilization. On the other hand, reactivity changes of HWRs over the full range of operating conditions from cold shutdown to full power are small. This reduces the required reactivity worth of control devices and minimizes local flux distribution perturbations, minimizing potential problems due to transient local overheating of fuel. Analyzing heavy water effectiveness on neutronic parameters such as enrichment requirements, peaking factor and reactivity is important and should pay attention as primary concepts of a HWR core designing. Two nuclear nuclear reactors of CANDU-type and hexagonal-type reactor cores of 33 fuel assemblies and 19 assemblies in 1.04 P/D have been respectively simulated using MCNP-4C code. Using heavy water and light water as moderator have been compared for achieving less reactivity insertion and enrichment requirements. Two fuel matrixes of (232Th/235U)O2 and (238/235U)O2 have been compared to achieve more economical and safe design. Heavy water not only decreased enrichment needs, but it concluded in negative reactivity insertions during moderator density variations. Thorium oxide fuel assemblies of 2.3% enrichment loaded into the core of heavy water moderator resulted in 0.751 fission to absorption ratio and peaking factor of 1.7 using. Heavy water not only provides negative reactivity insertion during temperature raises which changes moderator density but concluded in 2 to 10 kg reduction of enrichment requirements, depend on geometry type.
Abstract: The indoor airflow with a mixed natural/forced convection
was numerically calculated using the laminar and turbulent
approach. The Boussinesq approximation was considered for a simplification
of the mathematical model and calculations. The results
obtained, such as mean velocity fields, were successfully compared
with experimental PIV flow visualizations. The effect of the distance
between the cooled wall and the heat exchanger on the temperature
and velocity distributions was calculated. In a room with a simple
shape, the computational code OpenFOAM demonstrated an ability to
numerically predict flow patterns. Furthermore, numerical techniques,
boundary type conditions and the computational grid quality were
examined. Calculations using the turbulence model k-omega had a
significant effect on the results influencing temperature and velocity
distributions.
Abstract: The Lattice Boltzmann Method (LBM) with double populations is applied to solve the steady-state laminar natural convective heat transfer in a triangular cavity filled with water. The bottom wall is heated, the vertical wall is cooled, and the inclined wall is kept adiabatic. The buoyancy effect was modeled by applying the Boussinesq approximation to the momentum equation. The fluid velocity is determined by D2Q9 LBM and the energy equation is discritized by D2Q4 LBM to compute the temperature field. Comparisons with previously published work are performed and found to be in excellent agreement. Numerical results are obtained for a wide range of parameters: the Rayleigh number from to and the inclination angle from 0° to 360°. Flow and thermal fields were exhibited by means of streamlines and isotherms. It is observed that inclination angle can be used as a relevant parameter to control heat transfer in right-angled triangular enclosures.