Abstract: A solar receiver is designed for operation under
extremely uneven heat flux distribution, cyclic weather, and cloud
transient cycle conditions, which can include large thermal stress and
even receiver failure. In this study, the effect of different oil velocity
on convection coefficient factor and impact of wind velocity on local
Nusselt number by Finite Volume Method will be analyzed. This
study is organized to give an overview of the numerical modeling
using a MATLAB software, as an accurate, time efficient and
economical way of analyzing the heat transfer trends over stationary
receiver tube for different Reynolds number. The results reveal when
oil velocity is below 0.33m/s, the value of convection coefficient is
negligible at low temperature. The numerical graphs indicate that
when oil velocity increases up to 1.2 m/s, heat convection coefficient
increases significantly. In fact, a reduction in oil velocity causes a
reduction in heat conduction through the glass envelope. In addition,
the different local Nusselt number is reduced when the wind blows
toward the concave side of the collector and it has a significant effect
on heat losses reduction through the glass envelope.
Abstract: This qualitative case study seeks to understand and
explain the deployment of radio frequency identification (RFID)
systems in two countries (i.e., in Taiwan for the adoption of electric
scooters and in Finland for supporting glass bottle recycling) using
the “Technology-Organization-Environment” theoretical framework.
This study also seeks to highlight the relevance and importance of
pursuing environmental sustainability in firms and in society in
general due to the social urgency of the issues involved.
Abstract: In this glasshouse study, we developed a new imagebased
non-destructive technique for detecting leaf P status of
different crops such as cotton, tomato and lettuce. The plants were
grown on a nutrient solution containing different P concentrations,
e.g. 0%, 50% and 100% of recommended P concentration (P0 = no P,
L; P1 = 2.5 mL 10 L-1 of P and P2 = 5 mL 10 L-1 of P). After 7 weeks
of treatment, the plants were harvested and data on leaf P contents
were collected using the standard destructive laboratory method and
at the same time leaf images were collected by a handheld crop image
sensor. We calculated leaf area, leaf perimeter and RGB (red, green
and blue) values of these images. These data were further used in
linear discriminant analysis (LDA) to estimate leaf P contents, which
successfully classified these plants on the basis of leaf P contents.
The data indicated that P deficiency in crop plants can be predicted
using leaf image and morphological data. Our proposed nondestructive
imaging method is precise in estimating P requirements of
different crop species.
Abstract: The objective of this study was to synthesize and
characterize the poly(alkenoic acid)s with different molecular
structures, use these polymers to formulate a dental cement
restorative, and study the effect of molecular structures on reaction
kinetics, viscosity, and mechanical strengths of the formed polymers
and cement restoratives. In this study, poly(alkenoic acid)s with
different molecular structures were synthesized. The purified
polymers were formulated with commercial Fuji II LC glass fillers to
form the experimental cement restoratives. The reaction kinetics was
studied via 1HNMR spectroscopy. The formed restoratives were
evaluated using compressive strength, diametral tensile strength,
flexural strength, hardness and wear-resistance tests. Specimens were
conditioned in distilled water at 37oC for 24 h prior to testing. Fuji II
LC restorative was used as control. The results show that the higher
the arm number and initiator concentration, the faster the reaction
was. It was also found that the higher the arm number and branching
that the polymer had, the lower the viscosity of the polymer in water
and the lower the mechanical strengths of the formed restorative. The
experimental restoratives were 31-53% in compressive strength, 37-
55% in compressive modulus, 80-126% in diametral tensile strength,
76-94% in flexural strength, 4-21% in fracture toughness and 53-96%
in hardness higher than Fuji II LC. For wear test, the experimental
restoratives were only 5.4-13% of abrasive and 6.4-12% of attritional
wear depths of Fuji II LC in each wear cycle. The aging study also
showed that all the experimental restoratives increased their strength
continuously during 30 days, unlike Fuji II LC. It is concluded that
polymer molecular structures have significant and positive impact on
mechanical properties of dental cement restoratives.
Abstract: At the present work, highly transparent strip type
quasi-solid state dye-sensitized solar cells (DSSCs) were fabricated
through inkjet printing using nanocomposite TiO2 inks as raw
materials and tested under outdoor illumination conditions. The cells,
which can be considered as the structural units of large area modules,
were fully characterized electrically and electrochemically and after
the evaluation of the received results a large area DSSC module was
manufactured. The module design was a sandwich Z-interconnection
where the working electrode is deposited on one conductive glass and
the counter electrode on a second glass. Silver current collective
fingers were printed on the conductive glasses to make the internal
electrical connections and the adjacent cells were connected in series
and finally insulated using a UV curing resin to protect them from the
corrosive (I-/I3-) redox couple of the electrolyte. Finally, outdoor tests
were carried out to the fabricated dye-sensitized solar module and its
performance data were collected and assessed.
Abstract: The development of composite materials and the
related design and manufacturing technologies is one of the most
important advances in the history of materials. Composites are
multifunctional materials having unprecedented mechanical and
physical properties that can be tailored to meet the requirements of a
particular application. Some composites also exhibit great resistance
to high-temperature corrosion, oxidation, and wear. Polymers are
widely used indoors and outdoors, therefore they are exposed to a
chemical environment which may include atmospheric oxygen, acidic
fumes, acidic rain, moisture heat and thermal shock, ultra-violet light,
high energy radiation, etc. Different polymers are affected differently
by these factors even though the amorphous polymers are more
sensitive. Ageing is also important and it is defined as the process of
deterioration of engineering materials resulting from the combined
effects of atmospheric radiation, heat, oxygen, water, microorganisms
and other atmospheric factors.
Abstract: The study conducted a simulation of the effect of sea
water to the bonding capacity of GFRP sheet on the concrete beams
using a simulation tank. Fiber reinforced polymer (FRP) has been
developed and applied in many fields civil engineering structures on
the new structures and also for strengthening of the deteriorated
structures. The FRP has advantages such as its corrosion resistance as
well as high tensile strength to weight ratio. Compared to the other
FRP materials, Glass composed FRP (GFRP) is relatively cheaper.
GFRP sheet is applied externally by bonding it on the concrete surface.
The studies regarding the application of GFRP sheet have been
conducted such as strengthening system, bonding behavior of GFRP
sheet including the application as reinforcement in new structures. For
application to the structures with direct contact to sea environment, a
study regarding the effect of sea water to the bonding capacity of
GFRP sheet is important to be clarified. To achieve the objective of the
study, a series of concrete beams strengthened with GFRP sheet on
extreme tension surface were prepared. The beams then were stored on
the sea water tank for six months. Results indicated the bonding
capacity decreased after six month exposed to the sea water.
Abstract: Carbon Fiber Reinforced Plastics (CFRPs) are widely
used for advanced applications, in particular in aerospace, automotive
and wind energy industries. Once cured to near net shape, CFRP
parts need several finishing operations such as trimming, milling or
drilling in order to accommodate fastening hardware and meeting the
final dimensions. The present research aims to study the effect of the
cutting temperature in trimming on the mechanical strength of high
performance CFRP laminates used for aeronautics applications. The
cutting temperature is of great importance when dealing with
trimming of CFRP. Temperatures higher than the glass-transition
temperature (Tg) of the resin matrix are highly undesirable: they
cause degradation of the matrix in the trimmed edges area, which can
severely affect the mechanical performance of the entire component.
In this study, a 9.50mm diameter CVD diamond coated carbide tool
with six flutes was used to trim 24-plies CFRP laminates. A
300m/min cutting speed and 1140mm/min feed rate were used in the
experiments. The tool was heated prior to trimming using a
blowtorch, for temperatures ranging from 20°C to 300°C. The
temperature at the cutting edge was measured using embedded KType
thermocouples. Samples trimmed for different cutting
temperatures, below and above Tg, were mechanically tested using
three-points bending short-beam loading configurations. New cutting
tools as well as worn cutting tools were utilized for the experiments.
The experiments with the new tools could not prove any correlation
between the length of cut, the cutting temperature and the mechanical
performance. Thus mechanical strength was constant, regardless of
the cutting temperature. However, for worn tools, producing a cutting
temperature rising up to 450°C, thermal damage of the resin was
observed. The mechanical tests showed a reduced mean resistance in
short beam configuration, while the resistance in three point bending
decreases with increase of the cutting temperature.
Abstract: Calcium Phosphate Cement (CPC) due to its high bioactivity and optimum bioresorbability shows excellent bone regeneration capability. Despite it has limited applications as bone implant due to its macro-porous microstructure causing its poor mechanical strength. The reinforcement of apatitic CPCs with biocompatible fibre glass phase is an attractive area of research to improve upon its mechanical strength. Here, we study the setting behaviour of Si-doped and un-doped α tri calcium phosphate (α - TCP) based CPC and its reinforcement with addition of E-glass fibre. Alpha Tri calcium phosphate powders were prepared by solid state sintering of CaCO3 , CaHPO4 and Tetra Ethyl Ortho Silicate (TEOS) was used as silicon source to synthesize Si doped α-TCP powders. Both initial and final setting time of the developed cement was delayed because of Si addition. Crystalline phases of HA (JCPDS 9- 432), α-TCP (JCPDS 29-359) and β-TCP (JCPDS 9-169) were detected in the X-ray diffraction (XRD) pattern after immersion of CPC in simulated body fluid (SBF) for 0 hours to 10 days. As Si incorporation in the crystal lattice stabilized the TCP phase, Si doped CPC showed little slower rate of conversion into HA phase as compared to un-doped CPC. The SEM image of the microstructure of hardened CPC showed lower grain size of HA in un-doped CPC because of premature setting and faster hydrolysis of un-doped CPC in SBF as compared that in Si-doped CPC. Premature setting caused generation of micro and macro porosity in un-doped CPC structure which resulted in its lower mechanical strength as compared to that in Si-doped CPC. It was found that addition of 10 wt% of E-glass fibre into Si-doped α-TCP increased the average DTS of CPC from 8 MPa to 15 MPa as the fibres could resists the propagation of crack by deflecting the crack tip. Our study shows that biocompatible E-glass fibre in optimum proportion in CPC matrix can enhance the mechanical strength of CPC without affecting its biocompatibility.
Abstract: Fiber Reinforced Polymer (FRP) is a composite material with exceptional properties that are capable to replace conventional steel reinforcement in reinforced and pre-stressed concrete structures. However, the main obstacle for their wide use in pre-stressed concrete application is the anchorage system. Due to the weakness of FRP in the transverse direction, the pre-stressing capacity of FRP bars are limited. This paper investigates the modification of the conventional wedge anchorage system to be used for stressing of FRP bars in pre-stressed applications. Epoxy adhesive material with glass FRP (GFRP) bars and conventional steel wedge were used in this paper. The GFRP bars are encased with epoxy at the anchor zone and the wedge system was used in pull-out test. The results showed a loading capacity of 47.6 kN which is 69% of the bar ultimate capacity. Additionally, nylon wedge was made with the same dimensions of the steel wedge and tested for GFRP bars without epoxy layer. The nylon wedge showed a loading capacity of 19.7 kN which is only 28.5% of the ultimate bar capacity.
Abstract: The using of waste materials in the construction
industry can reduce the dependence on the natural aggregates which
are going at the end to deplete. The glass waste is generated in a huge
amount which can make one of its disposals in concrete industry
effective not only as a green solution but also as an advantage to
enhance the performance of mechanical properties and durability of
concrete. This article reports the performance of concrete specimens
containing different percentages of milled glass waste as a partial
replacement of cement (Powder), when they are subject to cycles of
freezing and thawing. The tests were conducted on 75-mm cubes and
75 x 75 x 300-mm prisms. Compressive strength based on laboratory
testing and non-destructive ultrasonic pulse velocity test were
performed during the action of freezing-thawing cycles (F/T). The
results revealed that the incorporation of glass waste in concrete
mixtures is not only feasible but also showed generally better strength
and durability performance than control concrete mixture. It may be
said that the recycling of waste glass in concrete mixes is not only a
disposal way, but also it can be an exploitation in concrete industry.
Abstract: Greenhouses offer us suitable conditions which can
be controlled easily for the growth of the plant and they are made by
using a covering material that allows the sun light entering into the
system. Covering material can be glass, fiber glass, plastic or another
transparent element. This study investigates the solar energy usability
rates and solar energy benefitting rates of a semi-spherical (modified
arch) type greenhouse system according to different orientations and
positions which exists under climatic conditions of Bayburt. In the
concept of this study it is tried to determine the best direction and
best sizes of a semi-spherical greenhouse to get best solar benefit
from the sun. To achieve this aim a modeling study is made by using
MATLAB. However, this modeling study is run for some determined
shapes and greenhouses it can be used for different shaped
greenhouses or buildings. The basic parameters are determined as
greenhouse azimuth angle, the rate of size of long edge to short and
seasonal solar energy gaining of greenhouse. The optimum azimuth
angles of 400, 300, 250, 200, 150, 100, 50 m2 modified arch
greenhouse are 90o, 90o, 35o, 35o, 34o, 33o and 22o while their
optimum k values (ratio of length to width) are 10, 10, 10, 10, 6, 4
and 4 respectively. Positioning the buildings in order to get more
solar heat energy in winter and less in summer brings out energy and
money savings and increases the comfort.
Abstract: We report herein the development and preliminary mechanical characterization of fully-dense multi-wall carbon nanotube (MWCNT)-reinforced ceramics and glasses based on a completely new methodology termed High Shear Compaction (HSC). The tubes are introduced and bound to the matrix grains by aid of polymeric binders to form flexible green bodies which are sintered and densified by spark plasma sintering to unprecedentedly high densities of 100% of the pure-matrix value. The strategy was validated across a PyrexTM glass / MWCNT composite while no identifiable factors limit application to other types of matrices. Nondestructive evaluation, based on ultrasonics, of the dynamic mechanical properties of the materials including elastic, shear and bulk modulus as well as Poisson’s ratio showed optimum property improvement at 0.5 %wt tube loading while evidence of nanoscalespecific energy dissipative characteristics acting complementary to nanotube bridging and pull-out indicate a high potential in a wide range of reinforcing and multifunctional applications.
Abstract: Potassium borates, which are widely used in welding
and metal refining industry, as a lubricating oil additive, cement
additive, fiberglass additive and insulation compound, are one of the
important groups of borate minerals. In this study the production of a
potassium borate mineral via hydrothermal method is aimed. The
potassium source of potassium nitrate (KNO3) was used along with a
sodium source of sodium hydroxide (NaOH) and boron source of
boric acid (H3BO3). The constant parameters of reaction temperature
and reaction time were determined as 80°C and 1 h, respectively. The
molar ratios of 1:1:3 (as KNO3:NaOH:H3BO3), 1:1:4, 1:1:5, 1:1:6
and 1:1:7 were used. Following the synthesis the identifications of
the produced products were conducted by X-Ray Diffraction (XRD),
Fourier Transform Infrared Spectroscopy (FT-IR) and Raman
Spectroscopy. The results of the experiments and analysis showed in
the ratio of 1:1:6, the Santite mineral with powder diffraction file
number (pdf no.) of 01-072-1688, which is known as potassium
pentaborate (KB5O8·4H2O) was synthesized as best.
Abstract: This paper presents the design and characterization of
analog readout interface circuits for ion sensitive field effect
transistor (ISFET) and ion selective electrode (ISE) based sensor.
These interface circuits are implemented using MIMOS’s 0.35um
CMOS technology and experimentally characterized under 24-leads
QFN package. The characterization evaluates the circuit’s
functionality, output sensitivity and output linearity. Commercial
sensors for both ISFET and ISE are employed together with glass
reference electrode during testing. The test result shows that the
designed interface circuits manage to readout signals produced by
both sensors with measured sensitivity of ISFET and ISE sensor are
54mV/pH and 62mV/decade, respectively. The characterized output
linearity for both circuits achieves above 0.999 Rsquare. The readout
also has demonstrated reliable operation by passing all qualifications
in reliability test plan.
Abstract: Aim of this work is to determine the theoretical and
experimental properties of filament wound glass fiber/epoxy resin
composite pipes with different winding design subjected under
bending. For determination of bending strength of composite samples
three point bending tests were conducted. Good correlation between
theoretical and experimental results has been obtained, where sample
No4 has shown the highest value of bending strength. All samples
have demonstrated matrix cracking and fiber failure followed by
layers delamination during testing. Also, it was found that smaller
winding angles lead to an increase in bending stress. From presented
results good merger between glass fibers and epoxy resin was
confirmed by SEM analysis.
Abstract: The polymer foil used for manufacturing of
laminated glass members behaves in a viscoelastic manner with
temperature dependance. This contribution aims at incorporating
the time/temperature-dependent behavior of interlayer to our earlier
elastic finite element model for laminated glass beams. The model
is based on a refined beam theory: each layer behaves according
to the finite-strain shear deformable formulation by Reissner and
the adjacent layers are connected via the Lagrange multipliers
ensuring the inter-layer compatibility of a laminated unit. The
time/temperature-dependent behavior of the interlayer is accounted
for by the generalized Maxwell model and by the time-temperature
superposition principle due to the Williams, Landel, and Ferry.
The resulting system is solved by the Newton method with
consistent linearization and the viscoelastic response is determined
incrementally by the exponential algorithm. By comparing the model
predictions against available experimental data, we demonstrate that
the proposed formulation is reliable and accurately reproduces the
behavior of the laminated glass units.
Abstract: One of the most famous techniques which affect the
efficiency of a production line is the assembly line balancing (ALB)
technique. This paper examines the balancing effect of a whole
production line of a real auto glass manufacturer in three steps. In the
first step, processing time of each activity in the workstations is
generated according to a practical approach. In the second step, the
whole production process is simulated and the bottleneck stations
have been identified, and finally in the third step, several
improvement scenarios are generated to optimize the system
throughput, and the best one is proposed. The main contribution of
the current research is the proposed framework which combines two
famous approaches including Assembly Line Balancing and
Optimization via Simulation technique (OvS). The results show that
the proposed framework could be applied in practical environments,
easily.
Abstract: The changes of the optical and structural properties of
Bismuth-Boro-Tellurite glasses pre and post gamma irradiation were
studied. Six glass samples, with different composition [(TeO2)0.7
(B2O3)0.3]1-x (Bi2O3)x prepared by melt quenching method were
irradiated with 25kGy gamma radiation at room temperature. The
Fourier Transform Infrared Spectroscopy (FTIR) was used to explore
the structural bonding in the prepared glass samples due to exposure,
while UV-VIS Spectrophotometer was used to evaluate the changes
in the optical properties before and after irradiation. Gamma
irradiation causes profound changes in the peak intensity as shown by
FTIR spectra which is due to the breaking of the network bonding.
Before gamma irradiation, the optical band gap, Eg value decreased
from 2.44 eV to 2.15 eV with the addition of Bismuth content. The
value kept decreasing (from 2.18 eV to 2.00 eV) following exposure
to gamma radiation due to the increase of non-bridging oxygen
(NBO) and the increase of defect in the glass. In conclusion, the glass
with high content of Bi2O3 (0.30Bi) give smallest Eg and show less
changes in FTIR spectra after gamma irradiation which indicate that
this glass is more resistant to gamma radiation compared to other
glasses.
Abstract: The structures obtained with the use of sandwich
technologies combine low weight with high energy absorbing
capacity and load carrying capacity. Hence, there is a growing and
markedly interest in the use of sandwiches with aluminum foam core
because of very good properties such as flexural rigidity and energy
absorption capability. In the current investigation, the static threepoint
bending tests were carried out on the sandwiches with
aluminum foam core and glass fiber reinforced polymer (GFRP)
skins at different values of support span distances aiming the analyses
of their flexural performance. The influence of the core thickness and
the GFRP skin type was reported in terms of peak load and energy
absorption capacity. For this purpose, the skins with two different
types of fabrics which have same thickness value and the aluminum
foam core with two different thicknesses were bonded with a
commercial polyurethane based flexible adhesive in order to combine
the composite sandwich panels. The main results of the bending tests
are: force-displacement curves, peak force values, absorbed energy,
collapse mechanisms and the effect of the support span length and
core thickness. The results of the experimental study showed that the
sandwich with the skins made of S-Glass Woven fabrics and with the
thicker foam core presented higher mechanical values such as load
carrying and energy absorption capacities. The increment of the
support span distance generated the decrease of the mechanical
values for each type of panels, as expected, because of the inverse
proportion between the force and span length. The most common
failure types of the sandwiches are debonding of the lower skin and
the core shear. The obtained results have particular importance for
applications that require lightweight structures with a high capacity
of energy dissipation, such as the transport industry (automotive,
aerospace, shipbuilding and marine industry), where the problems of
collision and crash have increased in the last years.