Abstract: Electron Beam Melting (EBM) is a metal powder bed-based Additive Manufacturing (AM) technology, which uses computer-controlled electron beams to create fully dense three-dimensional near-net-shaped parts from metal powder. It gives the ability to produce any complex parts directly from a computer-aided design (CAD) model without tools and dies, and with a variety of materials. However, the quality of the surface finish in EBM process has limitations to meeting the performance requirements of additively manufactured components. The aim of this study is to investigate the cutting forces induced during milling Ti6Al4V produced by EBM as well as the surface quality of the milled surfaces. The effects of cutting speed and radial depth of cut on the cutting forces, surface roughness, and surface morphology were investigated. The results indicated that the cutting speed was found to be proportional to the resultant cutting force at any cutting conditions while the surface roughness improved significantly with the increase in cutting speed and radial depth of cut.
Abstract: Chip formation characteristics are investigated during surface finishing of high density polyethylene (HDPE) samples using a shaper machine. Both the cutting speed and depth of cut are varied continually to enable observations under various machining conditions. The generated chips are analyzed in terms of their shape, size, and deformation. Their physical appearances are also observed using digital camera and optical microscope. The investigation shows that continuous chips are obtained for all the cutting conditions. It is observed that cutting speed is more influential than depth of cut to cause dimensional changes of chips. Chips curl radius is also found to increase gradually with the increase of cutting speed. The length of continuous chips remains always smaller than the job length, and the corresponding discrepancies are found to be more prominent at lower cutting speed. Microstructures of the chips reveal that cracks are formed at higher cutting speeds and depth of cuts, which is not that significant at low depth of cut.
Abstract: Laser cutting is a very common production method for cutting 2D polymeric parts. Developing of polymer composites with nano-fibers makes important their other properties like laser workability. The aim of this research is investigation of the influence different laser cutting conditions on the dimensional accuracy of parts and holes from poly methyl methacrylate (PMMA)/carbon nanotubes (CNTs) material. Experiments were carried out by considering of CNTs (in four level 0,0.5, 1 and 1.5% wt.%), laser power (60, 80, and 100 watt) and cutting speed 20, 30, and 40 mm/s as input variable factors. The results reveal that CNTs adding improves the laser workability of PMMA and the increasing of power has a significant effect on the part and hole size. The findings also show cutting speed is effective parameter on the size accuracy. Eventually, the statistical analysis of results was done, and calculated mathematical equations by the regression are presented for determining relation between input and output factor.
Abstract: In this study, an approach to identify factors affecting on surface roughness in a machining process is presented. This study is based on 81 data about surface roughness over a wide range of cutting tools (conventional, cutting tool with holes, cutting tool with composite material), workpiece materials (AISI 1045 Steel, AA2024 aluminum alloy, A48-class30 gray cast iron), spindle speed (630-1000 rpm), feed rate (0.05-0.075 mm/rev), depth of cut (0.05-0.15 mm) and tool overhang (41-65 mm). A single decision tree (SDT) analysis was done to identify factors for predicting a model of surface roughness, and the CART algorithm was employed for building and evaluating regression tree. Results show that a single decision tree is better than traditional regression models with higher rate and forecast accuracy and strong value.
Abstract: Nickel-based superalloys are generally known to be difficult to cut due to their strength, low thermal conductivity, and high work hardening tendency. Superalloy such as alloy 625 is often used in the oil and gas industry as a surfacing material to provide wear and corrosion resistance to components. The material is typically applied onto a metallic substrate through weld overlay cladding, an arc welding technique. Cladded surfaces are always rugged and carry a tough skin; this creates further difficulties to the machining process. The present work utilised design of experiment to optimise the internal cylindrical rough turning for weld overlay surfaces. An L27 orthogonal array was used to assess effects of the four selected key process variables: cutting insert, depth of cut, feed rate, and cutting speed. The optimal cutting conditions were determined based on productivity and the level of tool wear.
Abstract: Vibration during machining process is crucial since it affects cutting tool, machine, and workpiece leading to a tool wear, tool breakage, and an unacceptable surface roughness. This paper applies a nonparametric statistical method, single decision tree (SDT), to identify factors affecting on vibration in machining process. Workpiece material (AISI 1045 Steel, AA2024 Aluminum alloy, A48-class30 Gray Cast Iron), cutting tool (conventional, cutting tool with holes in toolholder, cutting tool filled up with epoxy-granite), tool overhang (41-65 mm), spindle speed (630-1000 rpm), feed rate (0.05-0.075 mm/rev) and depth of cut (0.05-0.15 mm) were used as input variables, while vibration was the output parameter. It is concluded that workpiece material is the most important parameters for natural frequency followed by cutting tool and overhang.
Abstract: Machining of Metal Matrix Composites (MMCs) is very significant process and has been a main problem that draws many researchers to investigate the characteristics of MMCs during different machining process. The poor machining properties of hard particles reinforced MMCs make drilling process a rather interesting task. Unlike drilling of conventional materials, many problems can be seriously encountered during drilling of MMCs, such as tool wear and cutting forces. Cutting tool wear is a very significant concern in industries. Cutting tool wear not only influences the quality of the drilled hole, but also affects the cutting tool life. Prediction the cutting tool life during drilling is essential for optimizing the cutting conditions. However, the relationship between tool life and cutting conditions, tool geometrical factors and workpiece material properties has not yet been established by any machining theory. In this research work, fuzzy subtractive clustering system has been used to model the cutting tool life in drilling of Al2O3 particle reinforced aluminum alloy composite to investigate of the effect of cutting conditions on cutting tool life. This investigation can help in controlling and optimizing of cutting conditions when the process parameters are adjusted. The built model for prediction the tool life is identified by using drill diameter, cutting speed, and cutting feed rate as input data. The validity of the model was confirmed by the examinations under various cutting conditions. Experimental results have shown the efficiency of the model to predict cutting tool life.
Abstract: Chatter vibrations, occurring during cutting process,
cause vibration between the cutting tool and workpiece, which
deteriorates surface roughness and reduces tool life. The purpose of
this study is to investigate the influence of cutting parameters and
tool construction on surface roughness and vibration in turning of
aluminum alloy AA2024. A new design of cutting tool is proposed,
which is filled up with epoxy granite in order to improve damping
capacity of the tool. Experiments were performed at the lathe using
carbide cutting insert coated with TiC and two different cutting tools
made of AISI 5140 steel. Taguchi L9 orthogonal array was applied to
design of experiment and to optimize cutting conditions. By the help
of signal-to-noise ratio and analysis of variance the optimal cutting
condition and the effect of the cutting parameters on surface
roughness and vibration were determined. Effectiveness of Taguchi
method was verified by confirmation test. It was revealed that new
cutting tool with epoxy granite has reduced vibration and surface
roughness due to high damping properties of epoxy granite in
toolholder.
Abstract: During machining process, chatter is an unavoidable
phenomenon. Boring bars possess the cantilever shape and due to
this, it is subjected to chatter. The adverse effect of chatter includes
the increase in temperature which will leads to excess tool wear. To
overcome these problems, in this investigation, Cartridge brass (Cu –
70% and Zn – 30%) is passively fixed on the boring bar and also
clearance is provided in order to reduce the displacement, tool wear
and cutting temperature. A conventional all geared lathe is attached
with vibrometer and pyrometer is used to measure the displacement
and temperature. The influence of input parameters such as cutting
speed, depth of cut and clearance on temperature, tool wear and
displacement are investigated for various cutting conditions. From
the result, the optimum conditions to obtain better damping in boring
process for chatter reduction is identified.
Abstract: This study investigates the effects of the lead angle
and chip thickness variation on surface roughness during the
machining of compacted graphite iron using ceramic cutting tools
under dry cutting conditions. Analytical models were developed for
predicting the surface roughness values of the specimens after the
face milling process. Experimental data was collected and imported
to the artificial neural network model. A multilayer perceptron model
was used with the back propagation algorithm employing the input
parameters of lead angle, cutting speed and feed rate in connection
with chip thickness. Furthermore, analysis of variance was employed
to determine the effects of the cutting parameters on surface
roughness. Artificial neural network and regression analysis were
used to predict surface roughness. The values thus predicted were
compared with the collected experimental data, and the
corresponding percentage error was computed. Analysis results
revealed that the lead angle is the dominant factor affecting surface
roughness. Experimental results indicated an improvement in the
surface roughness value with decreasing lead angle value from 88° to
45°.
Abstract: The wear of cutting tool degrades the quality of the product in the manufacturing processes. The on line monitoring of the cutting tool wear level is very necessary to prevent the deterioration of the quality of machining. Unfortunately there is not a direct manner to measure the cutting tool wear on line. Consequently we must adopt an indirect method where wear will be estimated from the measurement of one or more physical parameters appearing during the machining process such as the cutting force, the vibrations, or the acoustic emission etc…. In this work, a neural network system is elaborated in order to estimate the flank wear from the cutting force measurement and the cutting conditions.
Abstract: This article is focused on the thermal spray coating machining issue. Those are irreplaceable in many areas of nowadays industrial branches such as aerospace industry, mostly thanks to their excellent qualities in production and also in renovation of machinery parts. The principals of thermal spraying and elementary diversification are described in introduction. Plasma coating method of composite materials – cermets – is described more thoroughly. The second part describes thermal spray coating machining and grinding in detail. This part contains suggestion of appropriate grinding tool and assessment of cutting conditions used for grinding a given part. Conclusion describes a problem which occurred while grinding a cermet thermal spray coating with a specially designed grindstone and a way to solve this problem.
Abstract: Determination of optimal conditions of machining parameters is important to reduce the production cost and achieve the desired surface quality. This paper investigates the influence of cutting parameters on surface roughness and natural frequency in turning of aluminum alloy AA2024. The experiments were performed at the lathe machine using two different cutting tools made of AISI 5140 and carbide cutting insert coated with TiC. Turning experiments were planned by Taguchi method L9 orthogonal array.Three levels for spindle speed, feed rate, depth of cut and tool overhang were chosen as cutting variables. The obtained experimental data has been analyzed using signal to noise ratio and analysis of variance. The main effects have been discussed and percentage contributions of various parameters affecting surface roughness and natural frequency, and optimal cutting conditions have been determined. Finally, optimization of the cutting parameters using Taguchi method was verified by confirmation experiments.
Abstract: In the present paper, the three-dimensional
temperature field of tool is determined during the machining and
compared with experimental work on C45 workpiece using carbide
cutting tool inserts. During the metal cutting operations, high
temperature is generated in the tool cutting edge which influence on
the rate of tool wear. Temperature is most important characteristic of
machining processes; since many parameters such as cutting speed,
surface quality and cutting forces depend on the temperature and high
temperatures can cause high mechanical stresses which lead to early
tool wear and reduce tool life. Therefore, considerable attention is
paid to determine tool temperatures. The experiments are carried out
for dry and orthogonal machining condition. The results show that
the increase of tool temperature depends on depth of cut and
especially cutting speed in high range of cutting conditions.
Abstract: The chatter is one of the major limitations of the productivity in the ball end milling process. It affects the surface roughness, the dimensional accuracy and the tool life. The aim of this research is to propose the new system to detect the chatter during the ball end milling process by using the wavelet transform. The proposed method is implemented on the 5-axis CNC machining center and the new three parameters are introduced from three dynamic cutting forces, which are calculated by taking the ratio of the average variances of dynamic cutting forces to the absolute variances of themselves. It had been proved that the chatter can be easier to detect during the in-process cutting by using the new parameters which are proposed in this research. The experimentally obtained results showed that the wavelet transform can provide the reliable results to detect the chatter under various cutting conditions.
Abstract: Titanium alloys like Ti-6Al-2Sn-4Zr-6Mo (Ti-
6246) are widely used in aerospace applications. Component
manufacturing, however, is difficult and expensive as their
machinability is extremely poor. A thorough understanding of the
chip formation process is needed to improve related metal cutting
operations.In the current study, orthogonal cutting experiments have
been performed and theresulting chips were analyzed by optical
microscopy and scanning electron microscopy.Chips from aTi-
6246ingot were produced at different cutting speeds and cutting
depths. During the experiments, depending of the cutting conditions,
continuous or segmented chips were formed. Narrow, highly
deformed and grain oriented zones, the so-called shear zone,
separated individual segments. Different material properties have
been measured in the shear zones and the segments.
Abstract: A judicious choice of insert material, tool geometry and
cutting conditions can make hard turning produce better surfaces than
grinding. In the present study, an attempt has been made to
investigate the effect of cutting tool materials on cutting forces (feed
force, thrust force and cutting force) in finish hard turning of AISI
D2 cold work tool steel. In conclusion of the results obtained with a
constant depth of cut and feed rate, it is important to note that cutting
force is directly affected by cutting tool material.
Abstract: In present work, prediction the effect of nose radius, rz (mm) on the equivalent strain (PEEQ) and surface finish during the machining of titanium alloy (Ti-6Al-4V) through orthogonal cutting process. The results were performed at several of the nose radiuses, rz (mm) while the cutting speed, vc (m/min), feed rate, f (mm/tooth) and depth of cut, d (mm) were remained constant. The equivalent plastic strain (PEEQ) was estimated by using finite element modeling (FEM) and applied through ABAQUS/EXPLICIT software. The simulation results led to conclude that the equivalent plastic strain (PEEQ) was increased and surface roughness (Ra) decreased when increasing nose radius, rz (mm) during the machining of titanium alloy (Ti–6Al–4V) in dry cutting conditions.
Abstract: The aim of this investigation is to study the
performance of the new generation of the PVD coated grade and to
map the influence of cutting conditions on the tool life in milling of
ADI (Austempered Ductile Iron). The results show that chipping is
the main wear mechanism which determines the tool life in dry
condition and notch wear in wet condition for this application. This
due to the different stress mechanisms and preexisting cracks in the
coating. The wear development shows clearly that the new PVD
coating (C20) has the best ability to delay the chipping growth. It
was also found that a high content of Al in the new coating (C20)
was especially favorable compared to a TiAlN multilayer with lower
Al content (C30) or CVD coating. This is due to fine grains and low
compressive stress level in the coating which increase the coating
ability to withstand the mechanical and thermal impact. It was also
found that the use of coolant decreases the tool life with 70-80%
compare to dry milling.
Abstract: Twist drills are geometrical complex tools and thus various researchers have adopted different mathematical and experimental approaches for their simulation. The present paper acknowledges the increasing use of modern CAD systems and using the API (Application Programming Interface) of a CAD system, drilling simulations are carried out. The developed DRILL3D software routine, creates parametrically controlled tool geometries and using different cutting conditions, achieves the generation of solid models for all the relevant data involved (drilling tool, cut workpiece, undeformed chip). The final data derived, consist a platform for further direct simulations regarding the determination of cutting forces, tool wear, drilling optimizations etc.