Abstract: This paper presents a new ultra-wideband (UWB) bandpass filter (BPF) with sharp roll-off and dual-notched bands. The filter consists of a triangle ring multi-mode resonator (MMR) with the stub-loaded resonator (SLR) for controlling the two transmission zeros at 2.8 / 11 GHz, the embedded open-circuited stub and the asymmetric tight coupled input/output (I/O) lines for introducing the dual notched bands at 5.2 / 6.8 GHz. The attenuation slope in the lower and higher passband edges of the proposed filter show 160- and 153-dB/GHz, respectively. This study mainly provides a simple method to design a UWB bandpass filter with high passband selectivity and dual-notched bands for satisfying the Federal Communications Commission (FCC-defined) indoor UWB specification
Abstract: The objective of the present study was to examine the
dose-response relationships between antioxidant parameters and liver
contaminant levels of Kazakhstan light crude oil (KLCO) in albino
rats. The animals were repeatedly exposed, by intraperitoneal
injection, to low dosages (0.5–1.5 ml/kg) of KLCO. Rats exposed to
these doses levels did not show any apparent symptoms of
intoxication. Serum aminotransferases increased significantly
(p
Abstract: In this study the elastic-plastic stress distribution in
weld-bonded joint, fabricated from austenitic stainless steel (AISI
304) sheet of 1.00 mm thickness and Epoxy adhesive Araldite 2011,
subjected to axial loading is investigated. This is needed to improve
design procedures and welding codes, and saving efforts in the
cumbersome experiments and analysis. Therefore, a complete 3-D
finite element modelling and analysis of spot welded, bonded and
weld-bonded joints under axial loading conditions is carried out. A
comprehensive systematic experimental program is conducted to
determine many properties and quantities, of the base metals and the
adhesive, needed for FE modelling, such like the elastic – plastic
properties, modulus of elasticity, fracture limit, the nugget and heat
affected zones (HAZ) properties, etc. Consequently, the finite
element models developed, for each case, are used to evaluate
stresses distributions across the entire joint, in both the elastic and
plastic regions. The stress distribution curves are obtained,
particularly in the elastic regions and found to be consistent and in
excellent agreement with the published data. Furthermore, the
stresses distributions are obtained in the weld-bonded joint and
display the best results with almost uniform smooth distribution
compared to spot and bonded cases. The stress concentration peaks at
the edges of the weld-bonded region, are almost eliminated resulting
in achieving the strongest joint of all processes.
Abstract: Stress analysis of functionally graded composite plates
composed of ceramic, functionally graded material and metal layers is
investigated using 3-D finite element method. In FGM layer, material
properties are assumed to be varied continuously in the thickness
direction according to a simple power law distribution in terms of the
volume fraction of a ceramic and metal. The 3-D finite element model
is adopted by using an 18-node solid element to analyze more
accurately the variation of material properties in the thickness
direction. Numerical results are compared for three types of materials.
In the analysis, the tensile and the compressive stresses are
summarized for various FGM thickness ratios, volume fraction
distributions, geometric parameters and mechanical loads.
Abstract: In this study, we propose a tongue diagnosis method
which detects the tongue from face image and divides the tongue area into six areas, and finally generates tongue coating ratio of each area.
To detect the tongue area from face image, we use ASM as one of the active shape models. Detected tongue area is divided into six areas
widely used in the Korean traditional medicine and the distribution of tongue coating of the six areas is examined by SVM(Support Vector
Machine). For SVM, we use a 3-dimensional vector calculated by PCA(Principal Component Analysis) from a 12-dimentional vector
consisting of RGB, HIS, Lab, and Luv. As a result, we detected the tongue area stably using ASM and found that PCA and SVM helped
raise the ratio of tongue coating detection.
Abstract: Today, transport and logistic systems are often tightly
integrated in the production. Lean production and just-in-time delivering create multiple constraints that have to be fulfilled. As transport networks often have evolved over time they are very
expensive to change. This paper describes a discrete-event-simulation
system which simulates transportation models using real time
resource routing and collision avoidance. It allows for the
specification of own control algorithms and validation of new
strategies. The simulation is integrated into a virtual reality (VR)
environment and can be displayed in 3-D to show the progress.
Simulation elements can be selected through VR metaphors. All data
gathered during the simulation can be presented as a detailed summary afterwards. The included cost-benefit calculation can help to optimize the financial outcome. The operation of this approach is shown by the example of a timber harvest simulation.
Abstract: Three-dimensional reconstruction of small objects has
been one of the most challenging problems over the last decade.
Computer graphics researchers and photography professionals have
been working on improving 3D reconstruction algorithms to fit the
high demands of various real life applications. Medical sciences,
animation industry, virtual reality, pattern recognition, tourism
industry, and reverse engineering are common fields where 3D
reconstruction of objects plays a vital role. Both lack of accuracy and
high computational cost are the major challenges facing successful
3D reconstruction. Fringe projection has emerged as a promising 3D
reconstruction direction that combines low computational cost to both
high precision and high resolution. It employs digital projection,
structured light systems and phase analysis on fringed pictures.
Research studies have shown that the system has acceptable
performance, and moreover it is insensitive to ambient light.
This paper presents an overview of fringe projection approaches. It
also presents an experimental study and implementation of a simple
fringe projection system. We tested our system using two objects
with different materials and levels of details. Experimental results
have shown that, while our system is simple, it produces acceptable
results.
Abstract: This research attempts to study the feasibility of
augmenting an augmented reality (AR) image card on a Quick
Response (QR) code. The authors have developed a new visual tag,
which contains a QR code and an augmented AR image card. The new
visual tag has features of reading both of the revealed data of the QR
code and the instant data from the AR image card. Furthermore, a
handheld communicating device is used to read and decode the new
visual tag, and then the concealed data of the new visual tag can be
revealed and read through its visual display. In general, the QR code is
designed to store the corresponding data or, as a key, to access the
corresponding data from the server through internet. Those reveled
data from the QR code are represented in text. Normally, the AR
image card is designed to store the corresponding data in
3-Dimensional or animation/video forms. By using QR code's
property of high fault tolerant rate, the new visual tag can access those
two different types of data by using a handheld communicating device.
The new visual tag has an advantage of carrying much more data than
independent QR code or AR image card. The major findings of this
research are: 1) the most efficient area for the designed augmented AR
card augmenting on the QR code is 9% coverage area out of the total
new visual tag-s area, and 2) the best location for the augmented AR
image card augmenting on the QR code is located in the bottom-right
corner of the new visual tag.
Abstract: White scar oyster (Crassostrea belcheri) is often eaten
raw and being the leading vehicle for foodborne disease, especially
Salmonella Weltevreden which exposed the prominent and most
resistant to radiation. Gamma irradiation at a low dose of 1 kGy was
enough to eliminate S. Weltevreden contaminated in oyster meat at a
level up to 5 log CFU/g while it still retain the raw characteristics and
equivalent sensory quality as the non-irradiated one. Process
development of ready-to-eat chilled oyster meat was conducted by
shucking the meat, individually packed in plastic bags, subjected to 1
kGy gamma radiation at chilled condition and then stored in 4oC
refrigerated temperature. Microbiological determination showed the
absence of S. Weltevreden (5 log CFU/g initial inoculated) along the
whole storage time of 30 days. Sensory evaluation indicated the
decreasing in sensory scores along storage time which determining
the product shelf life to be 18 days compared to 15 days of nonirradiated
one. The most advantage of developed process was to
provide the safe raw oyster to consumers and in addition sensory
quality retained and 3-day extension shelf life also exist.
Abstract: This paper proposes a method of adaptively generating a gait pattern of biped robot. The gait synthesis is based on human's gait pattern analysis. The proposed method can easily be applied to generate the natural and stable gait pattern of any biped robot. To analyze the human's gait pattern, sequential images of the human's gait on the sagittal plane are acquired from which the gait control values are extracted. The gait pattern of biped robot on the sagittal plane is adaptively generated by a genetic algorithm using the human's gait control values. However, gait trajectories of the biped robot on the sagittal plane are not enough to construct the complete gait pattern because the biped robot moves on 3-dimension space. Therefore, the gait pattern on the frontal plane, generated from Zero Moment Point (ZMP), is added to the gait one acquired on the sagittal plane. Consequently, the natural and stable walking pattern for the biped robot is obtained.
Abstract: The objective of this work is to investigate the
turbulent reacting flow in a three dimensional combustor with
emphasis on the effect of inlet swirl flow through a numerical
simulation. Flow field is analyzed using the SIMPLE method which is
known as stable as well as accurate in the combustion modeling, and
the finite volume method is adopted in solving the radiative transfer
equation. In this work, the thermal and flow characteristics in a three
dimensional combustor by changing parameters such as equivalence
ratio and inlet swirl angle have investigated. As the equivalence ratio
increases, which means that more fuel is supplied due to a larger inlet
fuel velocity, the flame temperature increases and the location of
maximum temperature has moved towards downstream. In the mean
while, the existence of inlet swirl velocity makes the fuel and
combustion air more completely mixed and burnt in short distance.
Therefore, the locations of the maximum reaction rate and temperature
were shifted to forward direction compared with the case of no swirl.
Abstract: This study deals with Computational Fluid Dynamics
(CFD) studies of the interactions between the air flow and louvered
fins which equipped the automotive heat exchangers. 3D numerical
simulation results are obtained by using the ANSYS Fluent 13.0 code
and compared to experimental data. The paper studies the effect of
louver angle and louver pitch geometrical parameters, on overall
thermal hydraulic performances of louvered fins.
The comparison between CFD simulations and experimental data
show that established 3-D CFD model gives a good agreement. The
validation agrees, with about 7% of deviation respectively of friction
and Colburn factors to experimental results. As first, it is found that
the louver angle has a strong influence on the heat transfer rate. Then,
louver angle and louver pitch variation of the louvers and their effects
on thermal hydraulic performances are studied. In addition to this
study, it is shown that the second half of the fin takes has a
significant contribution on pressure drop increase without any
increase in heat transfer.
Abstract: The experiment was conducted to evaluate
digestibility quantities of protein in Canola Meals (CMs) between
caecectomised and intact adult Rhode Island Red (RIR) cockerels
with using conventional addition method (CAM) for 7 d: a 4-d
adaptation and a 3-d experiment period on the basis of a completely
randomized design with 4 replicates. Results indicated that
caecectomy decreased (P
Abstract: Many medical devices are driven by motor pumps. Some researchers reported that the vibration mainly affected medical devices using a motor pump. The purpose of this study was to examine the effect of stiffness and damping coefficient in a 3-dimensional (3D) model of a motor pump and spring. In the present paper, experimental and mathematical tests for the moments of inertia of the 3D model and the material properties were investigated by an INSTRON machine. The response surfaces could be generated by using 3D multi-body analysis and the design of experiment method. It showed that differences in contours of the response surface were clearly found for the particular area. Displacement of the center of the motor pump was decreased at K≈2000 N/M, C≈12.5 N-sec/M. However, the frequency was increased at K≈2000 N/M, C≈15 N-sec/M. In this study, this study suggested experimental technique for vibration reduction for a motor pump in medical device. The combined method suggested in this study will greatly contribute to design of medical devices concerning vibration and noise intervention.
Abstract: Biochemical Oxygen Demand (BOD) is a measure of
the oxygen used in bacteria mediated oxidation of organic substances
in water and wastewater. Theoretically an infinite time is required for
complete biochemical oxidation of organic matter, but the
measurement is made over 5-days at 20 0C or 3-days at 27 0C test
period with or without dilution. Researchers have worked to further
reduce the time of measurement.
The objective of this paper is to review advancement made in
BOD measurement primarily to minimize the time and negate the
measurement difficulties. Survey of literature review in four such
techniques namely BOD-BARTTM, Biosensors, Ferricyanidemediated
approach, luminous bacterial immobilized chip method.
Basic principle, method of determination, data validation and their
advantage and disadvantages have been incorporated of each of the
methods.
In the BOD-BARTTM method the time lag is calculated for the
system to change from oxidative to reductive state. BIOSENSORS
are the biological sensing element with a transducer which produces
a signal proportional to the analyte concentration. Microbial species
has its metabolic deficiencies. Co-immobilization of bacteria using
sol-gel biosensor increases the range of substrate. In ferricyanidemediated
approach, ferricyanide has been used as e-acceptor instead
of oxygen. In Luminous bacterial cells-immobilized chip method,
bacterial bioluminescence which is caused by lux genes was
observed. Physiological responses is measured and correlated to
BOD due to reduction or emission.
There is a scope to further probe into the rapid estimation of BOD.
Abstract: Content-based Image Retrieval (CBIR) aims at searching image databases for specific images that are similar to a given query image based on matching of features derived from the image content. This paper focuses on a low-dimensional color based indexing technique for achieving efficient and effective retrieval performance. In our approach, the color features are extracted using the mean shift algorithm, a robust clustering technique. Then the cluster (region) mode is used as representative of the image in 3-D color space. The feature descriptor consists of the representative color of a region and is indexed using a spatial indexing method that uses *R -tree thus avoiding the high-dimensional indexing problems associated with the traditional color histogram. Alternatively, the images in the database are clustered based on region feature similarity using Euclidian distance. Only representative (centroids) features of these clusters are indexed using *R -tree thus improving the efficiency. For similarity retrieval, each representative color in the query image or region is used independently to find regions containing that color. The results of these methods are compared. A JAVA based query engine supporting query-by- example is built to retrieve images by color.
Abstract: This is the second part of the paper. It, aside from the
core subroutine test reported previously, focuses on the simulation of
turbulence governed by the full STF Navier-Stokes equations on a
large scale. Law of the wall is found plausible in this study as a model
of the boundary layer dynamics. Model validations proceed to
include velocity profiles of a stationary turbulent Couette flow, pure
sloshing flow simulations, and the identification of water-surface
inclination due to fluid accelerations. Errors resulting from the
irrotational and hydrostatic assumptions are explored when studying
a wind-driven water circulation with no shakings. Illustrative
examples show that this numerical strategy works for the simulation
of sloshing-shear mixed flow in a 3-D rigid rectangular base tank.
Abstract: This paper proposes a three-dimensional motion capture and feedback system of flying disc throwing action learners with use of Kinect device. Rather than conventional 3-D motion capture system, Kinect has advantages of cost merit, easy system development and operation. A novice learner of flying disc is trained to keep arm movement in steady height, to twist the waist, and to stretch the elbow according to the waist angle. The proposing system captures learners- body movement, checks their skeleton positions in pre-motion / motion / post-motion in several ways, and displays feedback messages to refine their actions.
Abstract: This paper presents nonlinear elastic dynamic analysis
of 3-D semi-rigid steel frames including geometric and connection
nonlinearities. The geometric nonlinearity is considered by using
stability functions and updating geometric stiffness matrix. The
nonlinear behavior of the steel beam-to-column connection is
considered by using a zero-length independent connection element
comprising of six translational and rotational springs. The nonlinear
dynamic equilibrium equations are solved by the Newmark numerical
integration method. The nonlinear time-history analysis results are
compared with those of previous studies and commercial SAP2000
software to verify the accuracy and efficiency of the proposed
procedure.
Abstract: Natural gas flow contains undesirable solid particles,
liquid condensation, and/or oil droplets and requires reliable
removing equipment to perform filtration. Recent natural gas
processing applications are demanded compactness and reliability of
process equipment. Since conventional means are sophisticated in
design, poor in efficiency, and continue lacking robust, a supersonic
nozzle has been introduced as an alternative means to meet such
demands.
A 3-D Convergent-Divergent Nozzle is simulated using
commercial Code for pressure ratio (NPR) varies from 1.2 to 2. Six
different shapes of nozzle are numerically examined to illustrate the
position of shock-wave as such spot could be considered as a
benchmark of particle separation. Rectangle, triangle, circular,
elliptical, pentagon, and hexagon nozzles are simulated using Fluent
Code with all have same cross-sectional area.
The simple one-dimensional inviscid theory does not describe the
actual features of fluid flow precisely as it ignores the impact of
nozzle configuration on the flow properties. CFD Simulation results,
however, show that nozzle geometry influences the flow structures
including location of shock wave.
The CFD analysis predicts shock appearance when p01/pa>1.2 for
almost all geometry and locates at the lower area ratio (Ae/At).
Simulation results showed that shock wave in Elliptical nozzle has
the farthest distance from the throat among the others at relatively
small NPR. As NPR increases, hexagon would be the farthest. The
numerical result is compared with available experimental data and
has shown good agreement in terms of shock location and flow
structure.