Abstract: The Euler-s equation of motion is extended to include
the viscosity stress tensor leading to the formulation of Navier–
Stokes type equation. The latter is linearized and applied to
investigate the rotational motion or vorticity in a viscous fluid.
Relations for the velocity of viscous waves and attenuation parameter
are obtained in terms of viscosity (μ) and the density (¤ü) of the fluid.
μ and ¤ü are measured experimentally as a function of temperature for
two different samples of light and heavy crude oil. These data
facilitated to determine the activation energy, velocity of viscous
wave and the attenuation parameter. Shear wave velocity in heavy oil
is found to be much larger than the light oil, whereas the attenuation
parameter in heavy oil is quite low in comparison to light one. The
activation energy of heavy oil is three times larger than light oil.
Abstract: The implementation of Super-Ultra Low Emission
Vehicle standards requires more efficient exhaust gas purification. To
increase the efficiency of exhaust gas purification, an the adsorbent
capable of holding hydrocarbons up to 250-300 ОС should be
developed. The possibility to design such adsorbents by modification
of zeolites of mordenite type, ZSM-5 and NaY, using different
metals cations has been studied.
It has been shown that introducing Cr, Cs, Zn, Ni, Co, Li, Mn in
zeolites results in modification of the toluene TPD and toluene
sorption capacity.
5%LiZSM-5 zeolite exhibits the most attractive TPD curve, with
toluene desorption temperature ranging from 250 to 350ОС. The
sorption capacity of 5%Li-ZSM-5 is 0.4 mmol/g. NaY zeolite has the
highest sorption capacity, up to 2 mmol/g, and holds toluene up to
350ОС, but at 120ОС toluene desorption starts, which is not desirable,
since the adsorbent of cold start hydrocarbons should retain them
until 250-300ОС. Therefore 5%LiZSM-5 zeolite was found to be the
most promising to control the cold-start hydrocarbon emissions
among the samples studied.
Abstract: Nanocrystalline thin film of Na0.1V2O5.nH2O xerogel
obtained by sol gel synthesis was used as gas sensor. Gas sensing
properties of different gases such as hydrogen, petroleum and
humidity were investigated. Applying XRD and TEM the size of the
nanocrystals is found to be 7.5 nm. SEM shows a highly porous
structure with submicron meter-sized voids present throughout the
sample. FTIR measurement shows different chemical groups
identifying the obtained series of gels. The sample was n-type
semiconductor according to the thermoelectric power and electrical
conductivity. It can be seen that the sensor response curves from
130oC to 150oC show a rapid increase in sensitivity for all types of
gas injection, low response values for heating period and the rapid
high response values for cooling period. This result may suggest that
this material is able to act as gas sensor during the heating and
cooling process.
Abstract: The study on the tree growth for four species groups of commercial timber in Koh Kong province, Cambodia-s tropical rainforest is described. The simulation for these four groups had been successfully developed in the 5-year interval through year-60. Data were obtained from twenty permanent sample plots in the duration of thirteen years. The aim for this study was to develop stand table simulation system of tree growth by the species group. There were five steps involved in the development of the tree growth simulation: aggregate the tree species into meaningful groups by using cluster analysis; allocate the trees in the diameter classes by the species group; observe the diameter movement of the species group. The diameter growth rate, mortality rate and recruitment rate were calculated by using some mathematical formula. Simulation equation had been created by combining those parameters. Result showed the dissimilarity of the diameter growth among species groups.
Abstract: The abundance and availability of rice husk, an agricultural waste, make them as a good source for precursor of activated carbon. In this work, rice husk-based activated carbons were prepared via base treated chemical activation process prior the carbonization process. The effect of carbonization temperatures (400, 600 and 800oC) on their pore structure was evaluated through morphology analysis using scanning electron microscope (SEM). Sample carbonized at 800oC showed better evolution and development of pores as compared to those carbonized at 400 and 600oC. The potential of rice husk-based activated carbon as an alternative adsorbent was investigated for the removal of Ni(II), Zn(II) and Pb(II) from single metal aqueous solution. The adsorption studies using rice husk-based activated carbon as an adsorbent were carried out as a function of contact time at room temperature and the metal ions were analyzed using atomic absorption spectrophotometer (AAS). The ability to remove metal ion from single metal aqueous solution was found to be improved with the increasing of carbonization temperature. Among the three metal ions tested, Pb(II) ion gave the highest adsorption on rice husk-based activated carbon. The results obtained indicate the potential to utilize rice husk as a promising precursor for the preparation of activated carbon for removal of heavy metals.
Abstract: 16-Mercaptohexadecanoic acid (MHDA) and tripeptide glutathione conjugated with gold nanoparticles (Au-NPs) are characterized by Fourier Transform InfaRared (FTIR) spectroscopy combined with Surface-enhanced Raman scattering (SERS) spectroscopy. Surface Plasmon Resonance (SPR) technique based on FTIR spectroscopy has become an important tool in biophysics, which is perspective for the study of organic compounds. FTIR-spectra of MHDA shows the line at 2500 cm-1 attributed to thiol group which is modified by presence of Au-NPs, suggesting the formation of bond between thiol group and gold. We also can observe the peaks originate from characteristic chemical group. A Raman spectrum of the same sample is also promising. Our preliminary experiments confirm that SERS-effect takes place for MHDA connected with Au-NPs and enable us to detected small number (less than 106 cm-2) of MHDA molecules. Combination of spectroscopy methods: FTIR and SERS – enable to study optical properties of Au- NPs and immobilized bio-molecules in context of a bio-nano-sensors.
Abstract: This paper describes the design of a voltage based maximum power point tracker (MPPT) for photovoltaic (PV) applications. Of the various MPPT methods, the voltage based method is considered to be the simplest and cost effective. The major disadvantage of this method is that the PV array is disconnected from the load for the sampling of its open circuit voltage, which inevitably results in power loss. Another disadvantage, in case of rapid irradiance variation, is that if the duration between two successive samplings, called the sampling period, is too long there is a considerable loss. This is because the output voltage of the PV array follows the unchanged reference during one sampling period. Once a maximum power point (MPP) is tracked and a change in irradiation occurs between two successive samplings, then the new MPP is not tracked until the next sampling of the PV array voltage. This paper proposes an MPPT circuit in which the sampling interval of the PV array voltage, and the sampling period have been shortened. The sample and hold circuit has also been simplified. The proposed circuit does not utilize a microcontroller or a digital signal processor and is thus suitable for low cost and low power applications.
Abstract: A new method identifies coupled fluid-structure system with a reduced set of state variables is presented. Assuming that the structural model is known a priori either from an analysis or a test and using linear transformations between structural and aeroelastic states, it is possible to deduce aerodynamic information from sampled time histories of the aeroelastic system. More specifically given a finite set of structural modes the method extracts generalized aerodynamic force matrix corresponding to these mode shapes. Once the aerodynamic forces are known, an aeroelastic reduced-order model can be constructed in discrete-time, state-space format by coupling the structural model and the aerodynamic system. The resulting reduced-order model is suitable for constant Mach, varying density analysis.
Abstract: This study aims to conduct a preliminary investigation to determine the topic to be focused in developing Virtual Laboratory For Biology (VLab-Bio). Samples involved in answering the questionnaire are form five students (equivalent to A-Level) and biology teachers. Time and economical resources for the setting up and construction of scientific laboratories can be solved with the adaptation of virtual laboratories as an educational tool. Thus, it is hoped that the proposed virtual laboratory will help students to learn the abstract concepts in biology. Findings show that the difficult topic chosen is Cell Division and the learning objective to be focused in developing the virtual lab is “Describe the application of knowledge on mitosis in cloning".
Abstract: Eight heavy metals (Cu, Cr, Zn, Hg, Pb, Cd, Ni and As) were analyzed in sediment samples in the dry and wet seasons from November 2009 to October 2010 in West Port of Peninsular Malaysia. The heavy metal concentrations (mg/kg dry weight) were ranged from 23.4 to 98.3 for Zn, 22.3 to 80 for Pb, 7.4 to 27.6 Cu, 0.244 to 3.53 for Cd, 7.2 to 22.2 for Ni, 20.2 to 162 for As, 0.11 to 0.409 for Hg and 11.5 to 61.5 for Cr. Metals concentrations in dry season were higher than the rainy season except in cupper and chromium. Analysis of variance with Statistical Analysis System (SAS) shows that the mean concentration of metals in the two seasons (α level=0.05) are not significantly different which shows that the metals were held firmly in the matrix of sediment. Also there are significant differences between control point station with other stations. According to the Interim Sediment Quality guidelines (ISQG), the metal concentrations are moderately polluted, except in arsenic which shows the highest level of pollution.
Abstract: Legionella pneumophila is involved in more than 95%
cases of severe atypical pneumonia. Infection is mainly by
inhalation the indoor aerosols through the water-coolant systems.
Because some Legionella strains may be viable but not culturable,
therefore, Taq polymerase, DNA amplification and semi-nested-PCR
were carried out to detect Legionella-specific 16S-rDNA sequence.
For this purpose, 1.5 litter of water samples from 77 water-coolant
system were collected from four different hospitals, two nursing
homes and one student hostel in Kerman city of Iran, each in a brand
new plastic bottle during summer season of 2006 (from April to
August). The samples were filtered in the sterile condition through
the Millipore Membrane Filter. DNA was extracted from membrane
and used for PCR to detect Legionella spp. The PCR product was
then subjected to semi-nested PCR for detection of L. pneumophila.
Out of 77 water samples that were tested by PCR, 30 (39%) were
positive for most species of Legionella. However, L. pneumophila
was detected from 14 (18.2%) water samples by semi-nested PCR.
From the above results it can be concluded that water coolant
systems of different hospitals and nursing homes in Kerman city of
Iran are highly contaminated with L. pneumophila spp. and pose
serious concern. So, we recommend avoiding such type of coolant
system in the hospitals and nursing homes.
Abstract: The aim of this study was to extract sugar from
sugarcane using high electric field pulse (HELP) as a non-thermal cell permeabilization method. The result of this study showed that it
is possible to permeablize sugar cane cells using HELP at very short times (less than 10 sec.) and at room temperature. Increasing the field strength (from 0.5kV/cm to 2kV/cm) and pulse number (1 to 12) led to increasing the permeabilization of sugar cane cells. The energy
consumption during HELP treatment of sugar cane (2.4 kJ/kg) was about 100 times less compared to thermal cell disintegration at 85
Abstract: A game animals – elk (Alces alces), deer (Cervus
elaphus), roe deer (Capreolus capreolus) or wild boar (Sus scrofa
scrofa) - every autumn and winter period provide an excellent
investment, diversification of many consumer meals. In last years
consumption and assortiment of game meat products significantly
increase. Investigations about biochemical composition of game meat
are not very much. The meat of wild animals is more favourable for
human health because it has lower saturated fatty acids content, but
higher content of protein. Therefore the aim of investigations was to
compare biochemical composition of ungulates obtained in
Latvia.Investigations were carried out in wild animals different
regions of Latvia. In the studied samples protein, intramuscular fat,
fatty acids and cholesterol were determined. The biochemical
analysis of 54 samples were done. Results of analysis showed that
protein content 22.36 – 22.92% of all types of meat samples is not
different statistically, significantly lower fat content 1.33 ± 0.88%
had elk meat samples and 1.59 ± 0.59% roe deer samples. Content of
cholesterol was various 64.41 – 95.07% in the ruminant meat
samples of different species. From the dietetic point of view the best
composition of fatty acids has meat samples of roe deer.
Abstract: The phylogenetic analysis using the most conservative
portions of 18S rRNA gene revealed the phylogenetic relationship
among the two populations where DNA divergence showed that the
nucleotides diversity value were -0.00838 for the Tanjung Dawai,
Kedah and -0.00708 for the Cherating, Pahang populations
respectively. The net nucleotide divergence among populations (Da)
was -0.0073 indicating a low polymorphism among the populations
studied. Total number of mutations in the Tanjung Dawai, Kedah
samples was higher than Cherating, Pahang samples, which are 73 and
59 respectively while shared mutations across the populations were 8,
and reveal the evolutionary in the genome of Malaysian T. gigas. The
tree topology of both populations inferred using Neigbour-joining
method by comparing 1791 bp of partial 18S rRNA sequence revealed
that T. gigas haplotypes were clustered into seven clades, suggesting
that they are genetically diverse among populations which derived
from a common ancestor.
Abstract: This paper presents a research conducted to investigate the effect of mixing process on polypropylene (PP) modified bitumen mixed with well graded aggregate to form modified bituminous concrete mix. Two mode of mixing, namely dry and wet with different concentration of polymer polypropylene was used with 80/100 pen bitumen, to evaluate the bituminous concrete mix properties. Three percentages of polymer varying from 1-3% by the weight of bitumen was used in this study. Three mixes namely control mix, wet mix and dry mix were prepared. Optimum binder content was calculated considering Marshall Stability, flow, air voids and Marshall Quotient at different bitumen content varying from 4% - 6.5% for control, dry and wet mix. Engineering properties thus obtained at the calculated optimum bitumen content revealed that wet mixing process is advantageous in comparison to dry mixing as it increases the stiffness of the mixture with the increase in polymer content in bitumen. Stiffness value for wet mix increases with the increase in polymer content which is beneficial in terms of rutting. 1% PP dry mix also shows enhanced stiffness, with the air void content limited to 4%.The flow behaviour of dry mix doesn't indicate any major difference with the increase in polymer content revealing that polymer acting as an aggregate only without affecting the viscosity of the binder in the mix. Polypropylene (PP) when interacted with 80 pen base bitumen enhances its performance characteristics which were brought about by altered rheological properties of the modified bitumen. The decrease in flow with the increase in binder content reflects the increase in viscosity of binder which induces the plastic flow in the mix. Workability index indicates that wet mix were easy to compact up to desired void ratio in comparison to dry mix samples.
Abstract: Dill contains range of phytochemicals, such as vitamin C and polyphenols, which significantly contribute to their total antioxidant activity. The aim of the current research was to determine the best blanching method for processing of dill prior to microwave vacuum drying based on the content of phenolic compounds, vitamin C and free radical scavenging activity. Two blanching mediums were used – water and steam, and for part of the samples microwave pretreatment was additionally used. Evaluation of vitamin C, phenolic contents and scavenging of DPPH˙ radical in dried dill was performed. Blanching had an effect on all tested parameters and the blanching conditions are very important. After evaluation of the results, as the best method for dill pretreatment was established blanching at 90 °C for 30 seconds.
Abstract: Rainbow trout homogametic males, (XX or YY sex genotype), can be obtained, respectively, through masculinisation of genetic females or induced androgenesis. Aim of this study was to compare reproductive potential of neo-males (XX) and super-males (YY) with heterogametic males (XY). We measured spermatozoa motility parameters, sperm concentration, osmolality and characterized protein profiles in samples of stripped and testicular sperm obtained from XY and YY males, and testicular sperm of XX males. The motile spermatozoa, as measured by both subjective method and CASA, showed no differences between testicular sperm of XX males and stripped sperm of XY and YY males whereas testicular sperm of XY and YY males had significantly lower sperm motility. Result of protein densitometry showed similarities in protein profile between seminal plasma of XY and YY males and testicular fluids of XX males. Testis of XX males showed specific histological structures of cysts consists hypertrophied Sertoli cells.
Abstract: Background: Regular physical activity contributes
positively to physical and psychological health. In the present study,
the stages of change of physical activity and the total physical
Aims: The aim of this study was to investigate the proportion of
adolescent girls in each stages of change and the causative factors
associated with physical activity such as the related social support
and self efficacy in a sample of the high school students.
Methods: In this study, Social Cognitive Theory (SCT) and the
Transtheorical Model (TTM) guided instrument development. The
data regarding the demographics, psychosocial determinants of
physical activity, stage of change and physical activity was gathered
by questionnaires. Several measures of psychosocial determinants of
physical activity were translated from English into Persian using the
back-translation technique. These translated measures were
administered to 512 ninth and tenth-grade Iranian high school
students for factor analysis.
Results: The distribution of the stage of change for physical activity
was as follow: 18/5% in precontemplation, 23.4% in contemplation,
38.2% in preparation, 4.6% in action and 15.3% in maintenance.
They were in 80.1% pre-adoption stages (precontemplation stage,
contemplation stage and preparation stage) and 19.9% post-adoption
stages (action stage and maintenance stage) of physical activity.
There was a significant relate between age and physical activity in
adolescent girls (age-related decline of physical activity) p
Abstract: this article proposed a methodology for computer
numerical control (CNC) machine scoring. The case study company
is a manufacturer of hard disk drive parts in Thailand. In this
company, sample of parts manufactured from CNC machine are
usually taken randomly for quality inspection. These inspection data
were used to make a decision to shut down the machine if it has
tendency to produce parts that are out of specification. Large amount
of data are produced in this process and data mining could be very
useful technique in analyzing them. In this research, data mining
techniques were used to construct a machine scoring model called
'machine priority assessment model (MPAM)'. This model helps to
ensure that the machine with higher risk of producing defective parts
be inspected before those with lower risk. If the defective prone
machine is identified sooner, defective part and rework could be
reduced hence improving the overall productivity. The results
showed that the proposed method can be successfully implemented
and approximately 351,000 baht of opportunity cost could have
saved in the case study company.
Abstract: The present study addresses problems and solutions
related to new functional food production. Wheat (Triticum aestivum
L) bran obtained from industrial mill company “Dobeles
dzirnavieks”, was used to investigate them as raw material like
nutrients for Bifidobacterium lactis Bb-12. Enzymatic hydrolysis of
wheat bran starch was carried out by α-amylase from Bacillus
amyloliquefaciens (Sigma Aldrich). The Viscozyme L purchased
from (Sigma Aldrich) were used for reducing released sugar.
Bifidibacterium lactis Bb-12 purchased from (Probio-Tec® CHR
Hansen) was cultivated in enzymatically hydrolysed wheat bran
mash. All procedures ensured the number of active Bifidobacterium
lactis Bb-12 in the final product reached 105 CFUg-1. After enzymatic
and bacterial fermentations sample were freeze dried for analysis of
chemical compounds. All experiments were performed at Faculty of
Food Technology of Latvia University of Agriculture in January-
March 2013. The obtained results show that both types of wheat bran
(enzymatically treated and non-treated) influenced the fermentative
activity and number of Bifidibacterium lactis Bb-12 viable in wheat
bran mash. Amount of acidity strongly increase during the wheat
bran mash fermentation. The main objective of this work was to
create low-energy functional enzymatically and bacterially treated
food from wheat bran using enzymatic hydrolysis of carbohydrates
and following cultivation of Bifidobacterium lactis Bb-12.