Abstract: The chemical and physical characteristics of rainwater
harvested from a typical rooftop were progressively studied. The
samples of rainwater collected were analyzed for pH, major ion
concentrations, TDS, turbidity, conductivity. All the Physicochemical
constituents fell within the WHO guideline limits at some points as
rainfall progresses except the pH. All the components of rainwater
quality measured during the study showed higher concentrations
during the early stages of rainfall and reduce as time progresses.
There was a downward trend in terms of pH as rain progressed, with
18% of the samples recording pH below the WHO limit of 6.5-8.0. It
was observed that iron concentration was above the WHO threshold
value of 0.3 mg/l on occasions of heavy rains. The results revealed
that most of physicochemical characteristics of rainwater samples
were generally below the WHO threshold, as such, the rainwater
characteristics showed satisfactory conditions in terms of
physicochemical constituents.
Abstract: Software fault prediction models are created by using
the source code, processed metrics from the same or previous version
of code and related fault data. Some company do not store and keep
track of all artifacts which are required for software fault prediction.
To construct fault prediction model for such company, the training
data from the other projects can be one potential solution. Earlier we
predicted the fault the less cost it requires to correct. The training
data consists of metrics data and related fault data at function/module
level. This paper investigates fault predictions at early stage using the
cross-project data focusing on the design metrics. In this study,
empirical analysis is carried out to validate design metrics for cross
project fault prediction. The machine learning techniques used for
evaluation is Naïve Bayes. The design phase metrics of other projects
can be used as initial guideline for the projects where no previous
fault data is available. We analyze seven datasets from NASA
Metrics Data Program which offer design as well as code metrics.
Overall, the results of cross project is comparable to the within
company data learning.
Abstract: There are many perceived advantages of microwave
ablation have driven researchers to develop innovative antennas to
effectively treat deep-seated, non-resectable hepatic tumors. In this
paper a coaxial antenna with a miniaturized sleeve choke has been
discussed for microwave interstitial ablation therapy, in order to
reduce backward heating effects irrespective of the insertion depth
into the tissue. Two dimensional Finite Element Method (FEM) is
used to simulate and measure the results of miniaturized sleeve choke
antenna. This paper emphasizes the importance of factors that can
affect simulation accuracy, which include mesh resolution, surface
heating and reflection coefficient. Quarter wavelength choke
effectiveness has been discussed by comparing it with the unchoked
antenna with same dimensions.
Abstract: This paper presents a numerical investigation of two
horizontally mounted four-lobed swirl pipes in terms of swirl
induction effectiveness into flows passing through them. The swirl
flows induced by the two swirl pipes have the potential to improve
the efficiency of Clean-In-Place procedures in a closed processing
system by local intensification of hydrodynamic impact on the
internal pipe surface. Pressure losses, swirl development within the
two swirl pipe, swirl induction effectiveness, swirl decay and wall
shear stress variation downstream of two swirl pipes are analyzed and
compared. It was found that a shorter length of swirl inducing pipe
used in joint with transition pipes is more effective in swirl induction
than when a longer one is used, in that it has a less constraint to the
induced swirl and results in slightly higher swirl intensity just
downstream of it with the expense of a smaller pressure loss. The
wall shear stress downstream of the shorter swirl pipe is also slightly
larger than that downstream of the longer swirl pipe due to the
slightly higher swirl intensity induced by the shorter swirl pipe. The
advantage of the shorter swirl pipe in terms of swirl induction is more
significant in flows with a larger Reynolds Number.
Abstract: Background: Worldwide, at least 2.8 million people
die each year as a result of being overweight or obese, and 35.8
million (2.3%) of global DALYs are caused by overweight or
obesity. Obesity is acknowledged as one of the burning public
health problems reducing life expectancy and quality of life. The
body composition analysis of the university population is essential
in assessing the nutritional status, as well as the risk of developing
diseases associated with abnormal body fat content so as to make
nutritional recommendations. Objectives: The main aim was to
determine the prevalence of obesity and overweight in University
students using Anthropometric analysis and BIA methods. Material
and Methods: In this cross-sectional study, 283 university students
participated. The body composition analysis was undertaken by
using mainly: i) Anthropometric Measurement: Height, Weight,
BMI, waist circumference, hip circumference and skin fold
thickness, ii) Bio-electrical impedance was used for analysis of
body fat mass, fat percent and visceral fat which was measured by
Tanita SC-330P Professional Body Composition Analyzer. The
data so collected were compiled in MS Excel and analyzed for
males and females using SPSS 16. Results and Discussion: The
mean age of the male (n= 153) studied subjects was 25.37 ±2.39
years and females (n=130) was 22.53 ±2.31. The data of BIA
revealed very high mean fat per cent of the female subjects i.e.
30.3±6.5 per cent whereas mean fat per cent of the male subjects
was 15.60±6.02 per cent indicating a normal body fat range. The
findings showed high visceral fat of both males (12.92±3.02) and
females (16.86±4.98). BMI, BF% and WHR were higher among
females, and BMI was higher among males. The most evident
correlation was verified between BF% and WHR for female
students (r=0.902; p
Abstract: This article presents two methods for the
compensation of harmonics generated by a nonlinear load. The first is
the classic method P-Q. The second is the controller by modern
method of artificial intelligence specifically fuzzy logic. Both
methods are applied to a shunt Active Power Filter (sAPF) based on a
three-phase voltage converter at five levels NPC topology. In
calculating the harmonic currents of reference, we use the algorithm
P-Q and pulse generation, we use the intersective PWM. For
flexibility and dynamics, we use fuzzy logic. The results give us clear
that the rate of Harmonic Distortion issued by fuzzy logic is better
than P-Q.
Abstract: Family is a basic unit of the society and the main
source of human development. The initial aim of the family is
psychological and social support of its members and has special
developmental stages. Researches show the families who have less
cohesion, have more conflicts and maladjustments and the members
of such families are not able to communicate effectively. Family is a
system in which any inter communication is related to child rearing
patterns and can affect it. Even the child rearing styles in childhood
can determine the family communications in adulthood. Therefore,
the aim of the present research was to examine the relationship
between child-rearing styles including authoritative, authoritarian and
permissive with dimensions of family communication patterns
including the conversation and conformity. The research design was a
correlational and the population consisted of the psychology students
of Roudehen Islamic Azad University who were studying in
academic year 2013-2014. A sample of 324 students was selected
randomly from the population. The research tools were the Baumrind
Child-rearing Questionnaires and Family Communication
Patterns Inventory, The Revised Scale of Koerner and Fitzpatrick.
The result was as below: (a) there was a positive and significant
relationship between conversation orientation and authoritative style.
(b) There was no significant relationship between conversation
orientation and other child-rearing styles. (c) There was a negative
significant relationship between conformity orientation and
authoritative style. (d) There was a positive significant relationship
between conformity orientation with authoritarian and permissive
styles. (e) There was a significant relationship between 3 dimensions
of child-rearing and communication patterns.
Abstract: Al6061 alloy base matrix, reinforced with particles of
silicon carbide (10 wt %) and Graphite powder (1wt%), known as
hybrid composites have been fabricated by liquid metallurgy route
(stir casting technique) and optimized at different parameters like
applied load, sliding speed and sliding distance by taguchi method. A
plan of experiment generated through taguchi technique was used to
perform experiments based on L27 orthogonal array. The developed
ANOVA and regression equations are used to find the optimum
coefficient of friction and wear under the influence of applied load,
sliding speed and sliding distance. On the basis of “smaller the best”
the dry sliding wear resistance was analysed and finally confirmation
tests were carried out to verify the experimental results.
Abstract: This research paper presents highly optimized barrel
shifter at 22nm Hi K metal gate strained Si technology node. This
barrel shifter is having a unique combination of static and dynamic
body bias which gives lowest power delay product. This power delay
product is compared with the same circuit at same technology node
with static forward biasing at ‘supply/2’ and also with normal reverse
substrate biasing and still found to be the lowest. The power delay
product of this barrel sifter is .39362X10-17J and is lowered by
approximately 78% to reference proposed barrel shifter at 32nm bulk
CMOS technology. Power delay product of barrel shifter at 22nm Hi
K Metal gate technology with normal reverse substrate bias is
2.97186933X10-17J and can be compared with this design’s PDP of
.39362X10-17J. This design uses both static and dynamic substrate
biasing and also has approximately 96% lower power delay product
compared to only forward body biased at half of supply voltage. The
NMOS model used are predictive technology models of Arizona state
university and the simulations to be carried out using HSPICE
simulator.
Abstract: We propose new multiple-channel piezoelectric (PZT)
actuated tunable optical filter based on racetrack multi-ring
resonators for wavelength de-multiplexing network applications. We
design tunable eight-channel wavelength de-multiplexer consisting of
eight cascaded PZT actuated tunable multi-ring resonator filter with a
channel spacing of 1.6nm. The filter for each channel is basically
structured on a suspended beam, sandwiched with piezoelectric
material and built in integrated ring resonators which are placed on
the middle of the beam to gain uniform stress and linearly varying
longitudinal strain. A reference single mode serially coupled multi
stage racetrack ring resonator with the same radii and coupling length
is designed with a line width of 0.8974nm with a flat top pass band at
1dB of 0.5205nm and free spectral range of about 14.9nm. In each
channel, a small change in the perimeter of the rings is introduced to
establish the shift in resonance wavelength as per the defined channel
spacing. As a result, when a DC voltage is applied, the beams will
elongate, which involves mechanical deformation of the ring
resonators that induces a stress and a strain, which brings a change in
refractive index and perimeter of the rings leading to change in the
output spectrum shift providing the tunability of central wavelength
in each channel. Simultaneous wave length shift as high as
45.54pm/
Abstract: Due to the continuous increment of the load demand,
identification of weaker buses, improvement of voltage profile and
power losses in the context of the voltage stability problems has
become one of the major concerns for the larger, complex,
interconnected power systems. The objective of this paper is to
review the impact of Flexible AC Transmission System (FACTS)
controller in Wind generators connected electrical network for
maintaining voltage stability. Wind energy could be the growing
renewable energy due to several advantages. The influence of wind
generators on power quality is a significant issue; non uniform power
production causes variations in system voltage and frequency.
Therefore, wind farm requires high reactive power compensation; the
advances in high power semiconducting devices have led to the
development of FACTS. The FACTS devices such as for example
SVC inject reactive power into the system which helps in maintaining
a better voltage profile. The performance is evaluated on an IEEE 14
bus system, two wind generators are connected at low voltage buses
to meet the increased load demand and SVC devices are integrated at
the buses with wind generators to keep voltage stability. Power
flows, nodal voltage magnitudes and angles of the power network are
obtained by iterative solutions using MIPOWER.
Abstract: Durian is the flagship fruit of Mindanao and there is
an abundance of several cultivars with many confusing identities/
names.
The project was conducted to develop procedure for reliable and
rapid detection and sorting of durian planting materials. Moreover, it
is also aimed to establish specific genetic or DNA markers for routine
testing and authentication of durian cultivars in question.
The project developed molecular procedures for routine testing.
SSR primers were also screened and identified for their utility in
discriminating durian cultivars collected.
Results of the study showed the following accomplishments:
1. Twenty (29) SSR primers were selected and identified based on
their ability to discriminate durian cultivars,
2. Optimized and established standard procedure for identification
and authentication of Durian cultivars
3. Genetic profile of durian is now available at Biotech Unit
Our results demonstrate the relevance of using molecular
techniques in evaluating and identifying durian clones. The most
polymorphic primers tested in this study could be useful tools for
detecting variation even at the early stage of the plant especially for
commercial purposes. The process developed combines the efficiency
of the microsatellites development process with the optimization of
non-radioactive detection process resulting in a user-friendly protocol
that can be performed in two (2) weeks and easily incorporated into
laboratories about to start microsatellite development projects. This
can be of great importance to extend microsatellite analyses to other
crop species where minimal genetic information is currently
available. With this, the University can now be a service laboratory
for routine testing and authentication of durian clones.
Abstract: The arsenic and iron environments in different growth
stages have been studied with EXAFS and XANES using
Brookhaven Synchrotron Light Source. Collard Greens plants were
grown and tissue samples were harvested. The project studied the
EXAFS and XANES of tissue samples using As and Fe K-edges. The
Fe absorption and the Fourier transform bond length information
were used as a control comparison. The Fourier transform of the
XAFS data revealed the coexistence of As (III) and As (V) in the As
bonding environment inside the studied plant tissue samples,
although the soil only had As (III). The data suggests that Collard
Greens has a novel pathway to handle arsenic absorption in soil.
Abstract: In Hungary, the society has changed a lot for the past
25 years, and these changes could be detected in educational
situations as well. The number and the intensity of conflicts have
been increased in most fields of life, as well as at schools. Teachers
have difficulties to be able to handle school conflicts. What is more,
the new net generation, generation Z has values and behavioural
patterns different from those of the previous one, which might
generate more serious conflicts at school, especially with teachers
who were mainly socialising in a traditional teacher – student
relationship.
In Hungary, the bill CCIV of 2011 declared the foundation of
Institutes of Teacher Training in higher education institutes. One of
the tasks of the Institutes is to survey the competences and needs of
teachers working in public education and to provide further trainings
and services for them according to their needs and requirements. This
job is supported by the Social Renewal Operative Programs 4.1.2.B.
The professors of a college carried out a questionnaire and surveyed
the needs and the requirements of teachers working in the region.
Based on the results, the professors of the Institute of Teacher
Training decided to meet the requirements of teachers and to launch
short teacher further training courses in spring 2015. One of the
courses is going to focus on school conflict management through
mediation.
The aim of the pilot course is to provide conflict management
techniques for teachers and to present different mediation techniques
to them. The theoretical part of the course (5 hours) will enable
participants to understand the main points and the advantages of
mediation, while the practical part (10 hours) will involve teachers in
role plays to learn how to cope with conflict situations applying
mediation. We hope if conflicts could be reduced, it would influence
school atmosphere in a positive way and the teaching – learning
process could be more successful and effective.
Abstract: The purpose of this study was to develop a descriptive
profile of the adapted physical activity research using single subject
experimental designs. All research articles using single subject
experimental designs published in the journal of Adapted Physical
Activity Quarterly from 1984 to 2013 were employed as the data
source. Each of the articles was coded in a subcategory of seven
categories: (a) the size of sample; (b) the age of participants; (c) the
type of disabilities; (d) the type of data analysis; (e) the type of
designs, (f) the independent variable, and (g) the dependent variable.
Frequencies, percentages, and trend inspection were used to analyze
the data and develop a profile. The profile developed characterizes a
small portion of research articles used single subject designs, in
which most researchers used a small sample size, recruited children
as subjects, emphasized learning and behavior impairments, selected
visual inspection with descriptive statistics, preferred a multiple
baseline design, focused on effects of therapy, inclusion, and
strategy, and measured desired behaviors more often, with a
decreasing trend over years.
Abstract: In this study, we proposed two techniques to track the
maximum power point (MPPT) of a photovoltaic system. The first is
an intelligent control technique, and the second is robust used for
variable structure system. In fact the characteristics I-V and P–V of
the photovoltaic generator depends on the solar irradiance and
temperature. These climate changes cause the fluctuation of
maximum power point; a maximum power point tracking technique
(MPPT) is required to maximize the output power. For this we have
adopted a control by fuzzy logic (FLC) famous for its stability and
robustness. And a Siding Mode Control (SMC) widely used for
variable structure system. The system comprises a photovoltaic panel
(PV), a DC-DC converter, which is considered as an adaptation stage
between the PV and the load. The modelling and simulation of the
system is developed using MATLAB/Simulink. SMC technique
provides a good tracking speed in fast changing irradiation and when
the irradiation changes slowly or it is constant the panel power of
FLC technique presents a much smoother signal with less
fluctuations.
Abstract: The use of engineered nanomaterials has increased as
a result of their positive impact on many sectors of the economy,
including agriculture. Silver nanoparticles (AgNPs) are now used to
enhance seed germination, plant growth, and photosynthetic quantum
efficiency and as antimicrobial agents to control plant diseases. In
this study, we examined the effect of AgNP dosage on the seed
germination of three plant species: corn (Zea mays L.), watermelon
(Citrullus lanatus [Thunb.] Matsum. & Nakai) and zucchini
(Cucurbita pepo L.). This experiment was designed to study the
effect of AgNPs on germination percentage, germination rate, mean
germination time, root length and fresh and dry weight of seedlings
for the three species. Seven concentrations (0.05, 0.1, 0.5, 1, 1.5, 2
and 2.5 mg/ml) of AgNPs were examined at the seed germination
stage. The three species had different dose responses to AgNPs in
terms of germination parameters and the measured growth
characteristics. The germination rates of the three plants were
enhanced in response to AgNPs. Significant enhancement of the
germination percentage values was observed after treatment of the
watermelon and zucchini plants with AgNPs in comparison with
untreated seeds. AgNPs showed a toxic effect on corn root
elongation, whereas watermelon and zucchini seedling growth were
positively affected by certain concentrations of AgNPs. This study
showed that exposure to AgNPs caused both positive and negative
effects on plant growth and germination.
Abstract: Hypersonic flows around spatial vehicles during their reentry phase in planetary atmospheres are characterized by intense aerothermodynamics phenomena. The aim of this work is to analyze high temperature flows around an axisymmetric blunt body taking into account chemical and vibrational non-equilibrium for air mixture species and the no slip condition at the wall. For this purpose, the Navier-Stokes equations system is resolved by the finite volume methodology to determine the flow parameters around the axisymmetric blunt body especially at the stagnation point and in the boundary layer along the wall of the blunt body. The code allows the capture of shock wave before a blunt body placed in hypersonic free stream. The numerical technique uses the Flux Vector Splitting method of Van Leer. CFL coefficient and mesh size level are selected to ensure the numerical convergence.
Abstract: This paper adopts a two-stage data envelopment
analysis to explore the impacts of financial development and bank
operating scale on bank efficiencies. The sample comprises
unbalanced panel data of 32 Taiwanese listed domestic commercial
banks over the period 1998 to 2013. Empirical results show that pure
technical efficiency is positively related to financial development,
whereas the effect of financial development on scale efficiency is
insignificant. Enlargement of bank operating scale improves bank
efficiencies, but the efficiency gains are decreased gradually when the
scale increases. Increases in capital adequacy ratio and market power
of loans lead into a growth of bank efficiencies.
Abstract: Micro-electromechanical system (MEMS)
accelerometers and gyroscopes are suitable for the inertial navigation
system (INS) of many applications due to low price, small
dimensions and light weight. The main disadvantage in a comparison
with classic sensors is a worse long term stability. The estimation
accuracy is mostly affected by the time-dependent growth of inertial
sensor errors, especially the stochastic errors. In order to eliminate
negative effects of these random errors, they must be accurately
modeled. In this paper, the Allan variance technique will be used in
modeling the stochastic errors of the inertial sensors. By performing
a simple operation on the entire length of data, a characteristic curve
is obtained whose inspection provides a systematic characterization
of various random errors contained in the inertial-sensor output data.