Abstract: Brass terminal, one of the several crude oil and
petroleum products storage/handling facilities in the Niger Delta was
built in the 1980s. Activities at this site, over the years, released
crude oil into this 3 m-deep, 1500 m-long canal lying adjacent to the
terminal with oil floating on it and its sediment heavily polluted. To
ensure effective clean-up, three major activities were planned: site
characterization, bioremediation pilot plant construction and testing
and full-scale bioremediation of contaminated sediment / bank soil by
land farming. The canal was delineated into 12 lots and each
characterized, with reference to the floating oily phase, contaminated
sediment and canal bank soil. As a result of site characterization, a
pilot plant for on-site bioremediation was designed and a treatment
basin constructed for carrying out pilot bioremediation test.
Following a designed sampling protocol, samples from this pilot
plant were collected for analysis at two laboratories as a quality
assurance / quality control check. Results showed that Brass Canal
upstream is contaminated with dark, thick and viscous oily film with
characteristic hydrocarbon smell while downstream, thin oily film
interspersed with water was observed. Sediments were observed to be
dark with mixture of brownish sandy soil with TPH ranging from
17,800 mg/kg in Lot 1 to 88,500 mg/kg in Lot 12 samples. Brass
Canal bank soil was observed to be sandy from ground surface to 3m,
below ground surface (bgs) it was silty-sandy and brownish while
subsurface soil (4-10m bgs) was sandy-clayey and whitish/grayish
with typical hydrocarbon smell. Preliminary results obtained so far
have been very promising but were proprietary. This project is
considered, to the best of technical literature knowledge, the first
large-scale on-site bioremediation project in the Niger Delta region,
Nigeria.
Abstract: In this paper, we propose a system for preventing gas
risks through the use of wireless communication modules and
intelligent gas safety appliances. Our system configuration consists of
an automatic extinguishing system, detectors, a wall-pad, and a
microcomputer controlled micom gas meter to monitor gas flow and
pressure as well as the occurrence of earthquakes. The automatic fire
extinguishing system checks for both combustible gaseous leaks and
monitors the environmental temperature, while the detector array
measures smoke and CO gas concentrations. Depending on detected
conditions, the micom gas meter cuts off an inner valve and generates
a warning, the automatic fire-extinguishing system cuts off an external
valve and sprays extinguishing materials, or the sensors generate
signals and take further action when smoke or CO are detected.
Information on intelligent measures taken by the gas safety appliances
and sensors are transmitted to the wall-pad, which in turn relays this as
real time data to a server that can be monitored via an external network
(BcN) connection to a web or mobile application for the management
of gas safety. To validate this smart-home gas management system, we
field-tested its suitability for use in Korean apartments under several
scenarios.
Abstract: The separation of Hg (II) from produced water by
hollow fiber contactors (HFC) was investigation. This system
included of two hollow fiber modules in the series connecting. The
first module used for the extraction reaction and the second module
for stripping reaction. Aliquat336 extractant was fed from the organic
reservoirs into the shell side of the first hollow fiber module and
continuous to the shell side of the second module. The organic liquid
was continuously feed recirculate and back to the reservoirs. The feed
solution was pumped into the lumen (tube side) of the first hollow
fiber module. Simultaneously, the stripping solution was pumped in
the same way in tube side of the second module. The feed and
stripping solution was fed which had a countercurrent flow. Samples
were kept in the outlet of feed and stripping solution at 1 hour and
characterized concentration of Hg (II) by Inductively Couple Plasma
Atomic Emission Spectroscopy (ICP-AES). Feed solution was
produced water from natural gulf of Thailand. The extractant was
Aliquat336 dissolved in kerosene diluent. Stripping solution used was
nitric acid (HNO3) and thiourea (NH2CSNH2). The effect of carrier
concentration and type of stripping solution were investigated.
Results showed that the best condition were 10 % (v/v) Aliquat336
and 1.0 M NH2CSNH2. At the optimum condition, the extraction and
stripping of Hg (II) were 98% and 44.2%, respectively.
Abstract: Dielectric ceramic samples in the BaO-Re2O3-TiO2
ternary system were synthesized with structural formula Ba2-
xRe4+2x/3Ti8O24 where Re= rare earth metal and Re= Sm and La where
x varies from 0.0 to 0.6 with step size 0.1. Polycrystalline samples
were prepared by the conventional solid state reaction technique. The
dielectric, electrical and impedance analysis of all the samples in the
frequency range 1KHz- 1MHz at room temperature (25°C) have been
done to get the understanding of electrical conduction and dielectric
relaxation and their correlation. Dielectric response of the samples at
lower frequencies shows dielectric dispersion while at higher
frequencies it shows dielectric relaxation. The ac conductivity is well
fitted by the Jonscher law. The spectroscopic data in the impedance
plane confirms the existence of grain contribution to the relaxation.
All the properties are found out to be function of frequency as well as
the amount of substitution.
Abstract: This paper presents a rank correlation curve. The
traditional correlation coefficient is valid for both continuous
variables and for integer variables using rank statistics. Since
the correlation coefficient has already been established in rank
statistics by Spearman, such a calculation can be extended to
the correlation curve.
This paper presents two survey questions. The survey
collected non-continuous variables. We will show weak to
moderate correlation. Obviously, one question has a negative
effect on the other. A review of the qualitative literature
can answer which question and why. The rank correlation
curve shows which collection of responses has a positive
slope and which collection of responses has a negative slope.
Such information is unavailable from the flat, ”first-glance”
correlation statistics.
Abstract: Waste load allocation (WLA) policies may use multiobjective
optimization methods to find the most appropriate and
sustainable solutions. These usually intend to simultaneously
minimize two criteria, total abatement costs (TC) and environmental
violations (EV). If other criteria, such as inequity, need for
minimization as well, it requires introducing more binary
optimizations through different scenarios. In order to reduce the
calculation steps, this study presents value index as an innovative
decision making approach. Since the value index contains both the
environmental violation and treatment costs, it can be maximized
simultaneously with the equity index. It implies that the definition of
different scenarios for environmental violations is no longer required.
Furthermore, the solution is not necessarily the point with minimized
total costs or environmental violations. This idea is testified for Haraz
River, in north of Iran. Here, the dissolved oxygen (DO) level of river
is simulated by Streeter-Phelps equation in MATLAB software. The
WLA is determined for fish farms using multi-objective particle
swarm optimization (MOPSO) in two scenarios. At first, the trade-off
curves of TC-EV and TC-Inequity are plotted separately as the
conventional approach. In the second, the Value-Equity curve is
derived. The comparative results show that the solutions are in a
similar range of inequity with lower total costs. This is due to the
freedom of environmental violation attained in value index. As a
result, the conventional approach can well be replaced by the value
index particularly for problems optimizing these objectives. This
reduces the process to achieve the best solutions and may find better
classification for scenario definition. It is also concluded that decision
makers are better to focus on value index and weighting its contents
to find the most sustainable alternatives based on their requirements.
Abstract: In this contribution two approaches for calculating
optimal trajectories for highly automated vehicles are presented and
compared. The first one is based on a non-linear vehicle model, used
for evaluation. The second one is based on a simplified model and
can be implemented on a current ECU. In usual driving situations
both approaches show very similar results.
Abstract: Medicinal plants are now gaining attractiveness in
treatment of bacterial infections and food preservation. The objective
of this study was to assess antibacterial activity of some medicinal
plants on pathogenic bacteria. Screening of antibacterial activity of
aqueous and methanol extracts of some plants: Jojoba, Ginger, Sage,
Thyme and Clove against Bacillus cereus, Salmonella typhimurium,
Staphylococcus aureus, Clostridium perfringens and Escherichia coli
were investigated. Antibacterial activity was performed by agar
diffusion and disc diffusion method. Jatropha, Jojoba, Clove and
Ginger extracts showed notable bacterial activity in the first
screening step then selected to be tested against Bacillus cereus
(Gram+), Staphylococcus aureus (Gram+) and Salmonella
typhimurium (Gram−) and their effect was compared using
antibiotics as control. Screening results showed potential antibacterial
activity of the tested plant extracts against the screened bacterial
strains. It was found that methanol extracts exhibited higher
antibacterial activity than aqueous extracts. Methanol extract of
Jatropha showed the highest inhibition zone against Staphylococcus
aureus (Gram+) with 24.00 mm diameter, compared to the other
plant extracts followed by clove. Meanwhile, the inhibition zones of
methanol extracts of Jojoba and Ginger were the same (12mm).The
Gram-positive bacteria were found to be more sensitive to aqueous
and methanol extracts than Gram-negative bacteria.
Abstract: One of the most famous techniques which affect the
efficiency of a production line is the assembly line balancing (ALB)
technique. This paper examines the balancing effect of a whole
production line of a real auto glass manufacturer in three steps. In the
first step, processing time of each activity in the workstations is
generated according to a practical approach. In the second step, the
whole production process is simulated and the bottleneck stations
have been identified, and finally in the third step, several
improvement scenarios are generated to optimize the system
throughput, and the best one is proposed. The main contribution of
the current research is the proposed framework which combines two
famous approaches including Assembly Line Balancing and
Optimization via Simulation technique (OvS). The results show that
the proposed framework could be applied in practical environments,
easily.
Abstract: The atmospheres in many cities along the coastal lines
in the world have been rapidly changed to coastal-industrial
atmosphere. Hence, it is vital to investigate the corrosion behavior of
steel exposed to this kind of environment. In this present study,
Electrochemical Impedance Spectrography (EIS) and film thickness
measurement were applied to monitor the corrosion behavior of
weathering steel covered with a thin layer of the electrolyte in a
wet-dry cyclic condition, simulating a coastal-industrial environment
at 25oC and 60% RH. The results indicate that in all cycles, the
corrosion rate increases during the drying process due to an increase in
anion concentration and an acceleration of oxygen diffusion enhanced
by the effect of the thinning out of the electrolyte. During the wet-dry
cyclic corrosion test, the long-term corrosion behavior of this steel
depends on the periods of exposure. Corrosion process is first
accelerated and then decelerated. The decelerating corrosion process is
contributed to the formation of the protective rust, favored by the
wet-dry cycle and the acid regeneration process during the rusting
process.
Abstract: The growth in the volume of text data such as books
and articles in libraries for centuries has imposed to establish
effective mechanisms to locate them. Early techniques such as
abstraction, indexing and the use of classification categories have
marked the birth of a new field of research called "Information
Retrieval". Information Retrieval (IR) can be defined as the task of
defining models and systems whose purpose is to facilitate access to
a set of documents in electronic form (corpus) to allow a user to find
the relevant ones for him, that is to say, the contents which matches
with the information needs of the user. This paper presents a new
semantic indexing approach of a documentary corpus. The indexing
process starts first by a term weighting phase to determine the
importance of these terms in the documents. Then the use of a
thesaurus like Wordnet allows moving to the conceptual level.
Each candidate concept is evaluated by determining its level of
representation of the document, that is to say, the importance of the
concept in relation to other concepts of the document. Finally, the
semantic index is constructed by attaching to each concept of the
ontology, the documents of the corpus in which these concepts are
found.
Abstract: Microscopic simulation tool kits allow for
consideration of the two processes of railway operations and the
previous timetable production. Block occupation conflicts on both
process levels are often solved by using defined train priorities. These
conflict resolutions (dispatching decisions) generate reactionary
delays to the involved trains. The sum of reactionary delays is
commonly used to evaluate the quality of railway operations, which
describes the timetable robustness. It is either compared to an
acceptable train performance or the delays are appraised
economically by linear monetary functions. It is impossible to
adequately evaluate dispatching decisions without a well-founded
objective function. This paper presents a new approach for the
evaluation of dispatching decisions. The approach uses mode choice
models and considers the behaviour of the end-customers. These
models evaluate the reactionary delays in more detail and consider
other competing modes of transport. The new approach pursues the
coupling of a microscopic model of railway operations with the
macroscopic choice mode model. At first, it will be implemented for
railway operations process but it can also be used for timetable
production. The evaluation considers the possibility for the customer
to interchange to other transport modes. The new approach starts to
look at rail and road, but it can also be extended to air travel. The
result of mode choice models is the modal split. The reactions by the
end-customers have an impact on the revenue of the train operating
companies. Different purposes of travel have different payment
reserves and tolerances towards late running. Aside from changes to
revenues, longer journey times can also generate additional costs.
The costs are either time- or track-specific and arise from required
changes to rolling stock or train crew cycles. Only the variable values
are summarised in the contribution margin, which is the base for the
monetary evaluation of delays. The contribution margin is calculated
for different possible solutions to the same conflict. The conflict
resolution is optimised until the monetary loss becomes minimal. The
iterative process therefore determines an optimum conflict resolution
by monitoring the change to the contribution margin. Furthermore, a
monetary value of each dispatching decision can also be derived.
Abstract: In this study, we proposed two techniques to track the
maximum power point (MPPT) of a photovoltaic system. The first is
an intelligent control technique, and the second is robust used for
variable structure system. In fact the characteristics I-V and P–V of
the photovoltaic generator depends on the solar irradiance and
temperature. These climate changes cause the fluctuation of
maximum power point; a maximum power point tracking technique
(MPPT) is required to maximize the output power. For this we have
adopted a control by fuzzy logic (FLC) famous for its stability and
robustness. And a Siding Mode Control (SMC) widely used for
variable structure system. The system comprises a photovoltaic panel
(PV), a DC-DC converter, which is considered as an adaptation stage
between the PV and the load. The modelling and simulation of the
system is developed using MATLAB/Simulink. SMC technique
provides a good tracking speed in fast changing irradiation and when
the irradiation changes slowly or it is constant the panel power of
FLC technique presents a much smoother signal with less
fluctuations.
Abstract: The article represents the results of research of
antitumor activity of different structural types of plant flavonoids
extracted by authors from Polygonum L. plants in commercial
reserves at the territory of the Republic of Kazakhstan. For the first
time ever the results comparative research of antitumor activity of
plant flavonoids of different structural groups and their synthetic
derivatives have been represented. The results of determination of
toxicity of flavonoids in single parenteral infusion conditions have
been represented. Experimental substantiation of possible
mechanisms of antiproliferative and cytotoxic action of flavonoids
has been suggested. The perspectives of usage of plant flavonoids as
medications and creation of effective dosage forms of antitumor
medicines on their basis have been substantiated.
Abstract: An efficient remanufacturing network lead to an
efficient design of sustainable manufacturing enterprise. In
remanufacturing network, products are collected from the customer
zone, disassembled and remanufactured at a suitable remanufacturing
facility. In this respect, another issue to consider is how the returned
product to be remanufactured, in other words, what is the best layout
for such facility. In order to achieve a sustainable manufacturing
system, Cellular Manufacturing System (CMS) designs are highly
recommended, CMSs combine high throughput rates of line layouts
with the flexibility offered by functional layouts (job shop).
Introducing the CMS while designing a remanufacturing network will
benefit the utilization of such a network. This paper presents and
analyzes a comprehensive mathematical model for the design of
Dynamic Cellular Remanufacturing Systems (DCRSs). In this paper,
the proposed model is the first one to date that considers CMS and
remanufacturing system simultaneously. The proposed DCRS model
considers several manufacturing attributes such as multi period
production planning, dynamic system reconfiguration, duplicate
machines, machine capacity, available time for workers, worker
assignments, and machine procurement, where the demand is totally
satisfied from a returned product. A numerical example is presented
to illustrate the proposed model.
Abstract: We investigated the structure and electronic properties
of the compound Mg1-xBixO with varying concentrations of 0, ¼, ½,
and ¾ x bismuth in the the cesium chloride (CsCl), zinc-blende
(ZnS), nickel arsenide (NiAs) NaCl (rock-salt) and WZ (wurtzite)
phases. We calculated. The calculations were performed using the
first-principles pseudo-potential method within the framework of spin
density functional theory (DFT).
Abstract: OPEN_EmoRec_II is an open multimodal corpus with
experimentally induced emotions. In the first half of the experiment,
emotions were induced with standardized picture material and in the
second half during a human-computer interaction (HCI), realized
with a wizard-of-oz design. The induced emotions are based on the
dimensional theory of emotions (valence, arousal and dominance).
These emotional sequences - recorded with multimodal data (facial
reactions, speech, audio and physiological reactions) during a
naturalistic-like HCI-environment one can improve classification
methods on a multimodal level.
This database is the result of an HCI-experiment, for which 30
subjects in total agreed to a publication of their data including the
video material for research purposes*. The now available open
corpus contains sensory signal of: video, audio, physiology (SCL,
respiration, BVP, EMG Corrugator supercilii, EMG Zygomaticus
Major) and facial reactions annotations.
Abstract: OPEN_EmoRec_II is an open multimodal corpus with
experimentally induced emotions. In the first half of the experiment,
emotions were induced with standardized picture material and in the
second half during a human-computer interaction (HCI), realized
with a wizard-of-oz design. The induced emotions are based on the
dimensional theory of emotions (valence, arousal and dominance).
These emotional sequences - recorded with multimodal data (facial
reactions, speech, audio and physiological reactions) during a
naturalistic-like HCI-environment one can improve classification
methods on a multimodal level.
This database is the result of an HCI-experiment, for which 30
subjects in total agreed to a publication of their data including the
video material for research purposes*. The now available open
corpus contains sensory signal of: video, audio, physiology (SCL,
respiration, BVP, EMG Corrugator supercilii, EMG Zygomaticus
Major) and facial reactions annotations.
Abstract: Ibeno, Nigeria hosts the operational base of Mobil
Producing Nigeria Unlimited (MPNU), a subsidiary of ExxonMobil
and the current highest oil & condensate producer in Nigeria. Besides
MPNU, other oil companies operate onshore, on the continental shelf
and deep offshore of the Atlantic Ocean in Ibeno, Nigeria. This study
was designed to delineate oil polluted sites in Ibeno, Nigeria using
geophysical methods of electrical resistivity (ER) and ground
penetrating radar (GPR). Results obtained revealed that there have
been hydrocarbon contaminations of this environment by past crude
oil spills as observed from high resistivity values and GPR profiles
which clearly show the distribution, thickness and lateral extent of
hydrocarbon contamination as represented on the radargram reflector
tones. Contaminations were of varying degrees, ranging from slight
to high, indicating levels of substantial attenuation of crude oil
contamination over time. Moreover, the display of relatively lower
resistivities of locations outside the impacted areas compared to
resistivity values within the impacted areas and the 3-D Cartesian
images of oil contaminant plume depicted by red, light brown and
magenta for high, low and very low oil impacted areas, respectively
confirmed significant recent pollution of the study area with crude
oil.
Abstract: The seismic risk mitigation from the perspective of
the old buildings stock is truly essential in Algerian urban areas,
particularly those located in seismic prone regions, such as Annaba
city, and which the old buildings present high levels of degradation
associated with no seismic strengthening and/or rehabilitation
concerns. In this sense, the present paper approaches the issue of the
seismic vulnerability assessment of old masonry building stocks
through the adaptation of a simplified methodology developed for a
European context area similar to that of Annaba city, Algeria.
Therefore, this method is used for the first level of seismic
vulnerability assessment of the masonry buildings stock of the old
city center of Annaba. This methodology is based on a vulnerability
index that is suitable for the evaluation of damage and for the
creation of large-scale loss scenarios. Over 380 buildings were
evaluated in accordance with the referred methodology and the
results obtained were then integrated into a Geographical Information
System (GIS) tool. Such results can be used by the Annaba city
council for supporting management decisions, based on a global view
of the site under analysis, which led to more accurate and faster
decisions for the risk mitigation strategies and rehabilitation plans.