Abstract: Waste Load Allocation (WLA) strategies usually
intend to find economic policies for water resource management.
Water quality trading (WQT) is an approach that uses discharge
permit market to reduce total environmental protection costs. This
primarily requires assigning discharge limits known as total
maximum daily loads (TMDLs). These are determined by monitoring
organizations with respect to the receiving water quality and
remediation capabilities. The purpose of this study is to compare two
approaches of TMDL assignment for WQT policy in small catchment
area of Haraz River, in north of Iran. At first, TMDLs are assigned
uniformly for the whole point sources to keep the concentrations of
BOD and dissolved oxygen (DO) at the standard level at checkpoint
(terminus point). This was simply simulated and controlled by
Qual2kw software. In the second scenario, TMDLs are assigned
using multi objective particle swarm optimization (MOPSO) method
in which the environmental violation at river basin and total treatment
costs are minimized simultaneously. In both scenarios, the equity
index and the WLA based on trading discharge permits (TDP) are
calculated. The comparative results showed that using economically
optimized TMDLs (2nd scenario) has slightly more cost savings rather
than uniform TMDL approach (1st scenario). The former annually
costs about 1 M$ while the latter is 1.15 M$. WQT can decrease
these annual costs to 0.9 and 1.1 M$, respectively. In other word,
these approaches may save 35 and 45% economically in comparison
with command and control policy. It means that using multi objective
decision support systems (DSS) may find more economical WLA,
however its outcome is not necessarily significant in comparison with
uniform TMDLs. This may be due to the similar impact factors of
dischargers in small catchments. Conversely, using uniform TMDLs
for WQT brings more equity that makes stakeholders not feel that
much envious of difference between TMDL and WQT allocation. In
addition, for this case, determination of TMDLs uniformly would be
much easier for monitoring. Consequently, uniform TMDL for TDP
market is recommended as a sustainable approach. However,
economical TMDLs can be used for larger watersheds.
Abstract: Psyllium gum alone and in combination with
sunflower oil was investigated as a possible alternative edible coating
for improvement of quality and shelf life of fresh-cut papaya.
Different concentrations including 0.5, 1 and 1.5 percent of psyllium
gum were used for coating of fresh-cut papaya. In some samples,
refined sunflower oil was used as a lipid component to increase the
effectiveness of coating in terms of water barrier properties. Soya
lecithin was used as an emulsifier in coatings containing oil.
Pretreatment with 1% calcium chloride was given to maintain the
firmness of fresh-cut papaya cubes. 1% psyllium gum coating was
found to yield better results. Further, addition of oil helped to
maintain the quality and acted as a barrier to water vapour, therefore,
minimizing the weight loss.
Abstract: This paper aims to study the effect of cold work
condition on the microstructure of Cu-1.5wt%Ti, and Cu-3.5wt%Ti
and hence mechanical properties. The samples under investigation
were machined, and solution heat treated. X-ray diffraction technique
is used to identify the different phases present after cold deformation
by compression and also different heat treatment and also measuring
the relative quantities of phases present. The metallographic
examination is used to study the microstructure of the samples. The
hardness measurements were used to indicate the change in
mechanical properties. The results are compared with the mechanical
properties obtained by previous workers. Experiments on cold
compression followed by aging of Cu-Ti alloys have indicated that
the most efficient hardening of the material results from continuous
precipitation of very fine particles within the matrix. These particles
were reported to be β`-type, Cu4Ti phase. The β`-β transformation
and particles coarsening within the matrix as well as long grain
boundaries were responsible for the overaging of Cu-1.5wt%Ti and
Cu-3.5wt%Ti alloys. It is well known that plate-like particles are β –
type, Cu3Ti phase. Discontinuous precipitation was found to start at
the grain boundaries and expand into grain interior. At the higher
aging temperature, a classic Widmanstätten morphology forms giving
rise to a coarse microstructure comprised of α and the equilibrium
phase β. Those results were confirmed by X-ray analysis, which
found that a few percent of Cu3Ti, β precipitates are formed during
aging at high temperature for long time for both Cu- Ti alloys (i.e.
Cu-1.5wt%Ti and Cu-3.5wt%Ti).
Abstract: Evidence shows that start-ups success is positively
correlated with the launch of the first product. However, new ventures
are seldom able to acquire abundant resources for new product
development (NPD), which means that entrepreneurs may depend on
personal creativity instead of physical investments to achieve and
accelerate innovation speed. This study accentuates the role of
entrepreneurial bricolage, which defined as making do by applying
combinations of the resources at hand to new problems and
opportunities, in the relations of creative self-efficacy and innovation
speed. This study uses the multiple regression analysis to test the
hypotheses in a sample of 203 start-ups operating in various creative
markets in Taiwan. Results reveal that creative self-efficacy is
positively and directly associated with innovation speed, whereas
entrepreneurial bricolage plays a full mediator. These findings offer
important theoretical and practical implications.
Abstract: Background: Delayed onset muscle soreness (DOMS)
is the most common symptom when ordinary individuals and athletes
are exposed to unaccustomed physical activity, especially eccentric
contraction which impairs athletic performance, ordinary people
work ability and physical functioning. Multitudes of methods have
been investigated to reduce DOMS. One of the valuable methods to
control DOMS is repeated bout effect (RBE) as a prophylactic
method. Purpose: To compare the repeated bout effect of
submaximal eccentric with maximal isometric contraction on induced
DOMS. Methods: Sixty normal male volunteers were assigned
randomly into three equal groups: Group A (first study group): 20
subjects received submaximal eccentric contraction on non-dominant
elbow flexors as a prophylactic exercise. Group B (second study
group): 20 subjects received maximal isometric contraction on nondominant
elbow flexors as a prophylactic exercise. Group C (control
group): 20 subjects did not receive any prophylactic exercises.
Maximal isometric peak torque of elbow flexors and patient related
elbow evaluation (PREE) scale were measured for each subject 3
times before, immediately after, and 48 hours after induction of
DOMS. Results: Post-hoc test for maximal isometric peak torque and
PREE scale immediately and 48 hours after induction of DOMS
revealed that group (A) and group (B) resulted in significant decrease
in maximal isometric strength loss and elbow pain and disability
rather than control group (C), but submaximal eccentric group (A)
was more effective than maximal isometric group (B) as it showed
more rapid recovery of functional strength and less degrees of elbow
pain and disability. Conclusion: Both submaximal eccentric
contraction and maximal isometric contraction were effective in
prevention of DOMS but submaximal eccentric contraction produced
a greater protective effect against muscle damage induced by
maximal eccentric exercise performed 2 days later.
Abstract: Market is an important factor for start-ups to look into
during decision-making in product development and related areas.
Emerging country markets are more uncertain in terms of information
availability and institutional supports. The literature review of market
uncertainty reveals the need for identifying factors representing the
market uncertainty. This paper identifies factors for market
uncertainty using Exploratory Factor Analysis (EFA) and confirmed
the number of factor retention using an alternative factor retention
criterion ‘Parallel Analysis’. 500 entrepreneurs, engaged in start-ups
from all over India participated in the study. This paper concludes
with the factor structure of ‘market uncertainty’ having dimensions of
uncertainty in industry orientation, uncertainty in customer
orientation and uncertainty in marketing orientation.
Abstract: The aim of this research was to reveal the link
between mental variables, such as spatial abilities, memory, intellect
and professional experience of drivers.
Participants were allocated to four groups: no experience,
inexperienced, skilled and professionals (total 85 participants). The
level of ability for spatial navigation and indicator of nonverbal
memory grow along the process of accumulation of driving
experience. At high levels of driving experience, this tendency is
especially noticeable. The professionals having personal
achievements in driving (racing) differ from skilled drivers in better
feeling of direction, which is specific for them not just in a short-term
situation of an experimental task, but also in life-size perspective.
The level of ability of mental rotation does not grow with the growth
of driving experience, which confirms the multiple intelligence
theory according to which spatial abilities represent specific, other
than logical intelligence type of intellect. The link between spatial
abilities, memory, intellect and professional experience of drivers
seems to be different relating spatial navigation or mental rotation as
different kinds of spatial abilities.
Abstract: In recent years, multi-antenna techniques are being considered as a potential solution to increase the flow of future wireless communication systems. The objective of this article is to study the emission and reception system MIMO (Multiple Input Multiple Output), and present the different reception decoding techniques. First we will present the least complex technical, linear receivers such as the zero forcing equalizer (ZF) and minimum mean squared error (MMSE). Then a nonlinear technique called ordered successive cancellation of interferences (OSIC) and the optimal detector based on the maximum likelihood criterion (ML), finally, we simulate the associated decoding algorithms for MIMO system such as ZF, MMSE, OSIC and ML, thus a comparison of performance of these algorithms in MIMO context.
Abstract: Fibre cement plates, often used in construction,
generally are made using quartz as an inert material, cement as a
binder and cellulose as a fibre. This paper, first of all, investigates the
mechanical properties and durability of fibre cement plates when
quartz is both partly and fully replaced with diatomite. Diatomite
does not only have lower density compared to quartz but also has
high pozzolanic activity. The main objective of this paper is the
investigation of the effects of supplementary cementing materials
(SCMs) on the short and long term mechanical properties and
durability characteristics of fibre cement plates prepared using
diatomite. Supplementary cementing materials such as ground
granulated blast furnace slug (GGBS) and fly ash (FA) are used in
this study. Volume proportions of 10, 20, 30 and 40% of GGBS and
FA are used as partial replacement materials to cement. Short and
long term mechanical properties such as compressive and flexural
strengths as well as sorptivity characteristics and mass were
investigated. Consistency and setting time at each replacement levels
of SCMs were also recorded. The effects of using supplementary
cementing materials on the carbonation and sulphate resistance of
fibre cement plates were then experimented. The results, first of all,
show that the use of diatomite as a full or partial replacement to
quartz resulted in a systematic decrease in total mass of the fibre
cement plates. The reduction of mass was largely due to the lower
density and finer particle size of diatomite compared to quartz. The
use of diatomite did not only reduce the mass of these plates but also
increased the compressive strength significantly as a result of its high
pozzolanic activity. The replacement levels of both GGBS and FA
resulted in a systematic decrease in short term compressive strength
with increasing replacement levels. This was essentially expected as
the total rate of hydration is much lower in GGBS and FA than that
of cement. Long term results however, indicated that the compressive
strength of fibre cement plates prepared using both GGBS and FA
increases with time and hence the compressive strength of plates
prepared using SCMs is either equivalent or more than the
compressive strength of plates prepared using cement alone.
Durability characteristics of fibre cement plates prepared using SCMs
were enhanced significantly. Measurements of sopritivty
characteristics were also indicated that the plates prepared using
SCMs has much lower water absorption capacities compared to
plates prepared cement alone. Much higher resistance to carbonation
and sulphate attach were observed with plates prepared using SCMs.
The results presented in this paper show that the use of SCMs does
not only support the production of more sustainable construction
materials but also enhances the mechanical properties and durability
characteristics of fibre cement plates.
Abstract: The sea waves carry thousands of GWs of power
globally. Although there are a number of different approaches to
harness offshore energy, they are likely to be expensive, practically
challenging, and vulnerable to storms. Therefore, this paper considers
using the near shore waves for generating mechanical and electrical
power. It introduces two new approaches, the wave manipulation and
using a variable duct turbine, for intercepting very wide wave fronts
and coping with the fluctuations of the wave height and the sea level,
respectively. The first approach effectively allows capturing much
more energy yet with a much narrower turbine rotor. The second
approach allows using a rotor with a smaller radius but captures
energy of higher wave fronts at higher sea levels yet preventing it
from totally submerging. To illustrate the effectiveness of the first
approach, the paper contains a description and the simulation results
of a scale model of a wave manipulator. Then, it includes the results
of testing a physical model of the manipulator and a single duct, axial
flow turbine in a wave flume in the laboratory. The paper also
includes comparisons of theoretical predictions, simulation results,
and wave flume tests with respect to the incident energy, loss in wave
manipulation, minimal loss, brake torque, and the angular velocity.
Abstract: Dynamics of a rotor supported by air bearings is
strongly depends on the pressure distribution between the rotor and
the bearing. In this study, internal pressure in air bearings is
numerical and experimental analyzed for different radial clearances.
Firstly the pressure distribution between rotor and bearing is modeled
using Reynold's equation and this model is solved numerically. The
rotor-bearing system is also modeled in four degree of freedom and it
is simulated for different radial clearances. Then, in order to validate
numerical results, a test rig is designed and the rotor bearing system
is run under the same operational conditions. Pressure signals of left
and right bearings are recorded. Internal pressure variations are
compared for numerical and experimental results for different radial
clearances.
Abstract: This paper presents an experimental study on
structural performance of an innovative noise barrier consisting of
poly-block, light polyurethane foam (LPF) and polyurea. This wall
system (flexi-wall) is intended to be employed as a vertical extension
to existing sound barriers in an accelerated construction method. To
aid in the wall design, several mechanical tests were conducted on
LPF specimens and two full-scale walls were then fabricated
employing the same LPF material. The full-scale walls were
subjected to lateral loading in order to establish their lateral
resistance. A cyclic fatigue test was also performed on a full-scale
flexi-wall in order to evaluate the performance of the wall under a
repetitive loading condition. The result of the experiments indicated
the suitability of flexi-wall in accelerated construction and confirmed
that the structural performance of the wall system under lateral
loading is satisfactory for the sound barrier application. The
experimental results were discussed and a preliminary design
procedure for application of flexi-wall in sound barrier applications
was also developed.
Abstract: In this paper, we investigated the athermal pressure
behavior of the structural and elastic properties of scheelite BaWO4
phase up to 7 GPa using the ab initio pseudo-potential method. The
calculated lattice parameters pressure relation have been compared
with the experimental values and found to be in good agreement with
these results. Moreover, we present for the first time the investigation
of the elastic properties of this compound using the density functional
perturbation theory (DFPT). It is shown that this phase is
mechanically stable up to 7 GPa after analyzing the calculated elastic
constants. Other relevant quantities such as bulk modulus, pressure
derivative of bulk modulus, shear modulus; Young’s modulus,
Poisson’s ratio, anisotropy factors, Debye temperature and sound
velocity have been calculated. The obtained results, which are
reported for the first time to the best of the author’s knowledge, can
facilitate assessment of possible applications of the title material.
Abstract: In this paper, we propose a new method for threedimensional
object indexing based on D.A.M.C-S.H.C descriptor
(Direct and Analytical Method for Calculating the Spherical
Harmonics Coefficients). For this end, we propose a direct
calculation of the coefficients of spherical harmonics with perfect
precision. The aims of the method are to minimize, the processing
time on the 3D objects database and the searching time of similar
objects to a request object.
Firstly we start by defining the new descriptor using a new
division of 3-D object in a sphere. Then we define a new distance
which will be tested and prove his efficiency in the search for similar
objects in the database in which we have objects with very various
and important size.
Abstract: Hemoglobin (HB) indicates anemia level and by
extension may reflect the nutritional level and perhaps the immunity
of an individual. Some antiretroviral drugs like Zidovudine are
known to cause anemia in people living with HIV/AIDS (PLWHA).
A cross sectional study using demographic data and blood specimen
from 218 female commercial sex workers attending antiretroviral
therapy (ART) clinics was conducted between December, 2009 and
July, 2011 to assess the effect of zidovudine on hematologic, and
RNA viral load of female sex workers receiving antiretroviral
treatment in north western Nigeria. Anemia is a common and serious
complication of both HIV infection and its treatment. In the setting of
HIV infection, anemia has been associated with decreased quality of
life, functional status, and survival. Antiretroviral therapy,
particularly the highly active antiretroviral therapy (HAART), has
been associated with a decrease in the incidence and severity of
anemia in HIV-infected patients who have received a HAART
regimen for at least 1 year. In this study, result has shown that of the
218 patients, 26 with hemoglobin count between 5.1 – 10g/dl were
observed to have the highest viral load count of 300,000 –
350,000copies/ml. It was also observed that most patients (190) with
HB of 10.1 – 15.0g/dl had viral load count of 200,000 – 250,000
copies /ml. An inverse relationship therefore exists i.e. the lower the
hemoglobin level, the higher the viral load count even though the test
statistics did not show any significance between the two (P = 0.206).
This shows that multivariate logistic regression analysis
demonstrated that anemia was associated with a CD4 + cell count
below 50/μL, female sex workers with a viral load above 100,000
copies/mL, who use zidovudine.
Severe anemia was less prevalent in this study population than in
historical comparators; however, mild to moderate anemia rates
remain high. The study therefore recommends that hematological and
virologic parameters be monitored closely in patients receiving first
line ART regimen.
Abstract: Experimental investigations of the DC electric field effect on thermal decomposition of biomass, formation of the axial flow of volatiles (CO, H2, CxHy), mixing of volatiles with swirling airflow at low swirl intensity (S ≈ 0.2-0.35), their ignition and on formation of combustion dynamics are carried out with the aim to understand the mechanism of electric field influence on biomass gasification, combustion of volatiles and heat energy production. The DC electric field effect on combustion dynamics was studied by varying the positive bias voltage of the central electrode from 0.6 kV to 3 kV, whereas the ion current was limited to 2 mA. The results of experimental investigations confirm the field-enhanced biomass gasification with enhanced release of volatiles and the development of endothermic processes at the primary stage of thermochemical conversion of biomass determining the field-enhanced heat energy consumption with the correlating decrease of the flame temperature and heat energy production at this stage of flame formation. Further, the field-enhanced radial expansion of the flame reaction zone correlates with a more complete combustion of volatiles increasing the combustion efficiency by 3% and decreasing the mass fraction of CO, H2 and CxHy in the products, whereas by 10% increases the average volume fraction of CO2 and the heat energy production downstream the combustor increases by 5-10%
Abstract: In the present study, response surface methodology has been used to optimize turn-assisted deep cold rolling process of AISI 4140 steel. A regression model is developed to predict surface hardness and surface roughness using response surface methodology and central composite design. In the development of predictive model, deep cold rolling force, ball diameter, initial roughness of the workpiece, and number of tool passes are considered as model variables. The rolling force and the ball diameter are the significant factors on the surface hardness and ball diameter and numbers of tool passes are found to be significant for surface roughness. The predicted surface hardness and surface roughness values and the subsequent verification experiments under the optimal operating conditions confirmed the validity of the predicted model. The absolute average error between the experimental and predicted values at the optimal combination of parameter settings for surface hardness and surface roughness is calculated as 0.16% and 1.58% respectively. Using the optimal processing parameters, the surface hardness is improved from 225 to 306 HV, which resulted in an increase in the near surface hardness by about 36% and the surface roughness is improved from 4.84µm to 0.252 µm, which resulted in decrease in the surface roughness by about 95%. The depth of compression is found to be more than 300µm from the microstructure analysis and this is in correlation with the results obtained from the microhardness measurements. Taylor hobson talysurf tester, micro vickers hardness tester, optical microscopy and X-ray diffractometer are used to characterize the modified surface layer.
Abstract: Given the limited research on Small and Mediumsized
Enterprises’ (SMEs) contribution to Corporate Social
Responsibility (CSR) and even scarcer research on Swiss SMEs, this
paper helps to fill these gaps by enabling the identification of supranational
SME parameters. Thus, the paper investigates the current
state of SME practices in Switzerland and across 15 other countries.
Combining the degree to which SMEs demonstrate an explicit (or
business case) approach or see CSR as an implicit moral activity with
the assessment of their attributes for “variety of capitalism” defines
the framework of this comparative analysis. To outline Swiss small
business CSR patterns in particular, 40 SME owner-managers were
interviewed. A secondary data analysis of studies from different
countries laid groundwork for this comparative overview of small
business CSR. The paper identifies Swiss small business CSR as
driven by norms, values, and by the aspiration to contribute to
society, thus, as an implicit part of the day-to-day business. Similar to
most Central European, Mediterranean, Nordic, and Asian countries,
explicit CSR is still very rare in Swiss SMEs. Astonishingly, also
British and American SMEs follow this pattern in spite of their strong
and distinctly liberal market economies. Though other findings show
that nationality matters this research concludes that SME culture and
an informal CSR agenda are strongly formative and superseding even
forces of market economies, nationally cultural patterns, and
language. Hence, classifications of countries by their market system,
as found in the comparative capitalism literature, do not match the
CSR practices in SMEs as they do not mirror the peculiarities of their
business. This raises questions on the universality and
generalisability of unmediated, explicit management concepts,
especially in the context of small firms.
Abstract: STRIM (Statistical Test Rule Induction Method) has been proposed as a method to effectively induct if-then rules from the decision table which is considered as a sample set obtained from the population of interest. Its usefulness has been confirmed by simulation experiments specifying rules in advance, and by comparison with conventional methods. However, scope for future development remains before STRIM can be applied to the analysis of real-world data sets. The first requirement is to determine the size of the dataset needed for inducting true rules, since finding statistically significant rules is the core of the method. The second is to examine the capacity of rule induction from datasets with contaminated attribute values created by missing data and noise, since real-world datasets usually contain such contaminated data. This paper examines the first problem theoretically, in connection with the rule length. The second problem is then examined in a simulation experiment, utilizing the critical size of dataset derived from the first step. The experimental results show that STRIM is highly robust in the analysis of datasets with contaminated attribute values, and hence is applicable to real-world data
Abstract: In this study, three robust predicting methods, namely artificial neural network (ANN), adaptive neuro fuzzy inference system (ANFIS) and support vector machine (SVM) were used for computing the resonant frequency of A-shaped compact microstrip antennas (ACMAs) operating at UHF band. Firstly, the resonant frequencies of 144 ACMAs with various dimensions and electrical parameters were simulated with the help of IE3D™ based on method of moment (MoM). The ANN, ANFIS and SVM models for computing the resonant frequency were then built by considering the simulation data. 124 simulated ACMAs were utilized for training and the remaining 20 ACMAs were used for testing the ANN, ANFIS and SVM models. The performance of the ANN, ANFIS and SVM models are compared in the training and test process. The average percentage errors (APE) regarding the computed resonant frequencies for training of the ANN, ANFIS and SVM were obtained as 0.457%, 0.399% and 0.600%, respectively. The constructed models were then tested and APE values as 0.601% for ANN, 0.744% for ANFIS and 0.623% for SVM were achieved. The results obtained here show that ANN, ANFIS and SVM methods can be successfully applied to compute the resonant frequency of ACMAs, since they are useful and versatile methods that yield accurate results.