Abstract: Proprietary sensor network systems are typically expensive, rigid and difficult to incorporate technologies from other vendors. When using competing and incompatible technologies, a non-proprietary system is complex to create because it requires significant technical expertise and effort, which can be more expensive than a proprietary product. This paper presents the Sensor Abstraction Layer (SAL) that provides middleware architectures with a consistent and uniform view of heterogeneous sensor networks, regardless of the technologies involved. SAL abstracts and hides the hardware disparities and specificities related to accessing, controlling, probing and piloting heterogeneous sensors. SAL is a single software library containing a stable hardware-independent interface with consistent access and control functions to remotely manage the network. The end-user has near-real-time access to the collected data via the network, which results in a cost-effective, flexible and simplified system suitable for novice users. SAL has been used for successfully implementing several low-cost sensor network systems.
Abstract: Revolutions Applications such as telecommunications, hands-free communications, recording, etc. which need at least one microphone, the signal is usually infected by noise and echo. The important application is the speech enhancement, which is done to remove suppressed noises and echoes taken by a microphone, beside preferred speech. Accordingly, the microphone signal has to be cleaned using digital signal processing DSP tools before it is played out, transmitted, or stored. Engineers have so far tried different approaches to improving the speech by get back the desired speech signal from the noisy observations. Especially Mobile communication, so in this paper will do reconstruction of the speech signal, observed in additive background noise, using the Kalman filter technique to estimate the parameters of the Autoregressive Process (AR) in the state space model and the output speech signal obtained by the MATLAB. The accurate estimation by Kalman filter on speech would enhance and reduce the noise then compare and discuss the results between actual values and estimated values which produce the reconstructed signals.
Abstract: This paper was to study the clothes dryer using waste
heat from a split type air conditioner with a capacity of 12,648 btu/h.
The drying chamber had a minimum cross section area with the size
of 0.5 x 1.0 m2. The chamber was constructed by sailcloth and was
inside folded with aluminium foil. Then, it was connected to the
condensing unit of an air conditioner. The experiment was carried out
in two aspects which were the clothes drying with and without
auxiliary fan unit. The results showed that the drying rate of clothes
in the chamber installed with and without auxiliary fan unit were
2.26 and 1.1 kg/h, respectively. In case of the chamber installed with
a auxiliary fan unit, the additional power of 0.011 kWh was
consumed and the drying rate was higher than that of clothes drying
without auxiliary fan unit. Without auxiliary fan unit installation, no
energy was required but there was a portion of hot air leaks away
through the punctured holes at the wall of the drying chamber, hence
the drying rate was dropped below. The drying rate of clothes drying
using waste heat was higher than natural indoor drying and
commercial dryer which their drying rate were 0.17 and 1.9 kg/h,
respectively. It was noted that the COP of the air conditioner did not
change during the operating of clothes drying.
Abstract: Stress-strain curve of inter-tube connected carbon nanotube (CNT) reinforced polymer composite under axial loading generated from molecular dynamics simulation is presented. Comparison of the response to axial mechanical loading between this composite system with composite systems reinforced by long, continuous CNTs (replicated via periodic boundary conditions) and short, discontinuous CNTs has been made. Simulation results showed that the inter-tube connection improved the mechanical properties of short discontinuous CNTs dramatically. Though still weaker than long CNT/polymer composite, more remarkable increase in the stiffness relative to the polymer was observed in the inter-tube connected CNT/polymer composite than in the discontinuous CNT/polymer composite. The manually introduced bridge break process resulted in a stress-strain curve of ductile fracture mode, which is consistent with the experimental result.
Abstract: The notion of intuitionistic fuzzy sets was introduced
by Atanassov as a generalization of the notion of fuzzy sets. Y.B. Jun
and S.Z. Song introduced the notion of intuitionistic fuzzy points.
In this paper we find some relations between the intuitionistic fuzzy
ideals of a semigroup S and the set of all intuitionistic fuzzy points
of S.
Abstract: In this paper, we present a vertical wire NMOS
device fabricated using CMOS compatible processes. The
impact of temperature on various device parameters is
investigated in view of usual increase in surrounding
temperature with device density.
Abstract: The paper presents the results of microhardness and
microstructure of low carbon steel surface melted using carbon
dioxide laser with a wavelength of 10.6μm and a maximum output
power of 2000W. The processing parameters such as the laser power,
and the scanning rate were investigated in this study. After surface
melting two distinct regions formed corresponding to the melted zone
MZ, and the heat affected zone HAZ. The laser melted region
displayed a cellular fine structures while the HAZ displayed
martensite or bainite structure. At different processing parameters,
the original microstructure of this steel (Ferrite+Pearlite) has been
transformed to new phases of martensitic and bainitic structures. The
fine structure and the high microhardness are evidence of the high
cooling rates which follow the laser melting. The melting pool and
the transformed microstructure in the laser surface melted region of
carbon steel showed clear dependence on laser power and scanning
rate.
Abstract: The article presents the whole model of IS/IT
architecture exception governance. As first, the assumptions of
presented model are set. As next, there is defined a generic
governance model that serves as a basis for the architecture exception
governance. The architecture exception definition and its attributes
follow. The model respects well known approaches to the area that
are described in the text, but it adopts higher granularity in
description and expands the process view with all the next necessary
governance components as roles, principles and policies, tools to
enable the implementation of the model into organizations. The
architecture exception process is decomposed into a set of processes
related to the architecture exception lifecycle consisting of set of
phases and architecture exception states. Finally, there is information
about my future research related to this area.
Abstract: Due to heavy energy constraints in WSNs clustering is
an efficient way to manage the energy in sensors. There are many
methods already proposed in the area of clustering and research is
still going on to make clustering more energy efficient. In our paper
we are proposing a minimum spanning tree based clustering using
divide and conquer approach. The MST based clustering was first
proposed in 1970’s for large databases. Here we are taking divide and
conquer approach and implementing it for wireless sensor networks
with the constraints attached to the sensor networks. This Divide and
conquer approach is implemented in a way that we don’t have to
construct the whole MST before clustering but we just find the edge
which will be the part of the MST to a corresponding graph and
divide the graph in clusters there itself if that edge from the graph can
be removed judging on certain constraints and hence saving lot of
computation.
Abstract: This paper presents a numerical approach for the static
and dynamic analysis of hydrodynamic radial journal bearings. In the
first part, the effect of shaft and housing deformability on pressure
distribution within oil film is investigated. An iterative algorithm that
couples Reynolds equation with a plane finite elements (FE)
structural model is solved. Viscosity-to-pressure dependency (Vogel-
Barus equation) is also included. The deformed lubrication gap and
the overall stress state are obtained. Numerical results are presented
with reference to a typical journal bearing configuration at two
different inlet oil temperatures. Obtained results show the great
influence of bearing components structural deformation on oil
pressure distribution, compared with results for ideally rigid
components. In the second part, a numerical approach based on
perturbation method is used to compute stiffness and damping
matrices, which characterize the journal bearing dynamic behavior.
Abstract: In this paper, a study on the applications of the
optimization and regression techniques for optimal calculation of
partial ratios of helical gearboxes with second-step double gear-sets
for minimal cross section dimension is introduced. From the condition
of the moment equilibrium of a mechanic system including three gear
units and their regular resistance condition, models for calculation of
the partial ratios of helical gearboxes with second-step double
gear-sets were given. Especially, by regression analysis, explicit
models for calculation of the partial ratios are introduced. These
models allow determining the partial ratios accurately and simply.
Abstract: Humic acids (HAs) have been shown to activate some
ion uptakes along with stimulating the lateral roots at effective
concentration of micronutrients. However, the effects of HA on ion
adsorption by plant roots are not easily explainable due to the
varieties of HAs that differ from origins. Therefore, this study was
aimed to investigate the effect of various concentrations of HA
obtained from the compost derived from mix manures and some
agricultural wastes on the growth of eggplant seedlings (Solanum
melongena L. cv. Chao Praya) in tissue cultures at low nutrient level.
Egg plant seeds were surfaced sterilized and germinated in ½
Murashige and Skoog medium (MS) without HA added or in ¼ MS
supplemented with 0, 25, 50, 75 and 100 ppm of HAs. Then, they
were cultured for 4 weeks under the controlled environment. The
results showed that seedlings grown on ¼MS supplemented with
HAs at the concentration of 25 and 50 ppm had the average plant
heights (2.49 and 2.28 cm, respectively) higher than the other
treatments. Both treatments also significantly showed the maximum
average fresh and dry weights (p
Abstract: The effect of the discontinuity of the rail ends and the
presence of lower modulus insulation material at the gap to the
variations of stresses in the insulated rail joint (IRJ) is presented. A
three-dimensional wheel – rail contact model in the finite element
framework is used for the analysis. It is shown that the maximum stress
occurs in the subsurface of the railhead when the wheel contact occurs
far away from the rail end and migrates to the railhead surface as the
wheel approaches the rail end; under this condition, the interface
between the rail ends and the insulation material has suffered
significantly increased levels of stress concentration. The ratio of the
elastic modulus of the railhead and insulation material is found to alter
the levels of stress concentration. Numerical result indicates that a
higher elastic modulus insulating material can reduce the stress
concentration in the railhead but will generate higher stresses in the
insulation material, leading to earlier failure of the insulation material
Abstract: Generally flow behavior in centrifugal fan is observed
to be in a state of instability with flow separation zones on suction
surface as well as near the front shroud. Overall performance of the
diffusion process in a centrifugal fan could be enhanced by
judiciously introducing the boundary layer suction slots. With easy
accessibility of CFD as an analytical tool, an extensive numerical
whole field analysis of the effect of boundary layer suction slots in
discrete regions of suspected separation points is possible. This paper
attempts to explore the effect of boundary layer suction slots
corresponding to various geometrical locations on the impeller with
converging configurations for the slots. The analysis shows that the
converging suction slots located on the impeller blade about 25%
from the trailing edge, significantly improves the static pressure
recovery across the fan. Also it is found that Slots provided at a
radial distance of about 12% from the leading and trailing edges
marginally improve the static pressure recovery across the fan.
Abstract: In this paper three different approaches for person
verification and identification, i.e. by means of fingerprints, face and
voice recognition, are studied. Face recognition uses parts-based
representation methods and a manifold learning approach. The
assessment criterion is recognition accuracy. The techniques under
investigation are: a) Local Non-negative Matrix Factorization
(LNMF); b) Independent Components Analysis (ICA); c) NMF with
sparse constraints (NMFsc); d) Locality Preserving Projections
(Laplacianfaces). Fingerprint detection was approached by classical
minutiae (small graphical patterns) matching through image
segmentation by using a structural approach and a neural network as
decision block. As to voice / speaker recognition, melodic cepstral
and delta delta mel cepstral analysis were used as main methods, in
order to construct a supervised speaker-dependent voice recognition
system. The final decision (e.g. “accept-reject" for a verification
task) is taken by using a majority voting technique applied to the
three biometrics. The preliminary results, obtained for medium
databases of fingerprints, faces and voice recordings, indicate the
feasibility of our study and an overall recognition precision (about
92%) permitting the utilization of our system for a future complex
biometric card.
Abstract: In this paper, a frequency-variation based method has
been proposed for transistor parameter estimation in a commonemitter
transistor amplifier circuit. We design an algorithm to estimate
the transistor parameters, based on noisy measurements of the output
voltage when the input voltage is a sine wave of variable frequency
and constant amplitude. The common emitter amplifier circuit has
been modelled using the transistor Ebers-Moll equations and the
perturbation technique has been used for separating the linear and
nonlinear parts of the Ebers-Moll equations. This model of the amplifier
has been used to determine the amplitude of the output sinusoid as
a function of the frequency and the parameter vector. Then, applying
the proposed method to the frequency components, the transistor
parameters have been estimated. As compared to the conventional
time-domain least squares method, the proposed method requires
much less data storage and it results in more accurate parameter
estimation, as it exploits the information in the time and frequency
domain, simultaneously. The proposed method can be utilized for
parameter estimation of an analog device in its operating range of
frequencies, as it uses data collected from different frequencies output
signals for parameter estimation.
Abstract: Markov games are a generalization of Markov
decision process to a multi-agent setting. Two-player zero-sum
Markov game framework offers an effective platform for designing
robust controllers. This paper presents two novel controller design
algorithms that use ideas from game-theory literature to produce
reliable controllers that are able to maintain performance in presence
of noise and parameter variations. A more widely used approach for
controller design is the H∞ optimal control, which suffers from high
computational demand and at times, may be infeasible. Our approach
generates an optimal control policy for the agent (controller) via a
simple Linear Program enabling the controller to learn about the
unknown environment. The controller is facing an unknown
environment, and in our formulation this environment corresponds to
the behavior rules of the noise modeled as the opponent. Proposed
controller architectures attempt to improve controller reliability by a
gradual mixing of algorithmic approaches drawn from the game
theory literature and the Minimax-Q Markov game solution
approach, in a reinforcement-learning framework. We test the
proposed algorithms on a simulated Inverted Pendulum Swing-up
task and compare its performance against standard Q learning.
Abstract: The study of the interaction between humans and
computers has been emerging during the last few years. This
interaction will be more powerful if computers are able to perceive
and respond to human nonverbal communication such as emotions. In
this study, we present the image-based approach to emotion
classification through lower facial expression. We employ a set of
feature points in the lower face image according to the particular face
model used and consider their motion across each emotive expression
of images. The vector of displacements of all feature points input to
the Adaptive Support Vector Machines (A-SVMs) classifier that
classify it into seven basic emotions scheme, namely neutral, angry,
disgust, fear, happy, sad and surprise. The system was tested on the
Japanese Female Facial Expression (JAFFE) dataset of frontal view
facial expressions [7]. Our experiments on emotion classification
through lower facial expressions demonstrate the robustness of
Adaptive SVM classifier and verify the high efficiency of our
approach.
Abstract: Wireless Sensor Networks (WSNs) have attracted the attention of many researchers. This has resulted in their rapid integration in very different areas such as precision agriculture,environmental monitoring, object and event detection and military surveillance. Due to the current WSN characteristics this technology is specifically useful in industrial areas where security, reliability and autonomy are basic, such as nuclear power plants, chemical plants, and others. In this paper we present a system based on WSNs to monitor environmental conditions around and inside a nuclear power plant, specifically, radiation levels. Sensor nodes, equipped with radiation sensors, are deployed in fixed positions throughout the plant. In addition, plant staff are also equipped with mobile devices with higher capabilities than sensors such as for example PDAs able to monitor radiation levels and other conditions around them. The system enables communication between PDAs, which form a Mobile Ad-hoc Wireless Network (MANET), and allows workers to monitor remote conditions in the plant. It is particularly useful during stoppage periods for inspection or in the event of an accident to prevent risk situations.