Abstract: Power transformer consists of components which are
under consistent thermal and electrical stresses. The major
component which degrades under these stresses is the paper
insulation of the power transformer. At site, lightning impulses and
cable faults may cause the winding deformation. In addition, the
winding may deform due to impact during transportation. A
deformed winding will excite more stress to its insulating paper thus
will degrade it. Insulation degradation will shorten the life-span of
the transformer. Currently there are two methods of detecting the
winding deformation which are Sweep Frequency Response
Analysis (SFRA) and Low Voltage Impulse Test (LVI). The latter
injects current pulses to the winding and capture the admittance
plot. In this paper, a transformer which experienced overheating and
arcing was identified, and both SFRA and LVI were performed.
Next, the transformer was brought to the factory for untanking. The
untanking results revealed that the LVI is more accurate than the
SFRA method for this case study.
Abstract: The soil moisture content is an important property of
the soil. The results of mean weekly gravimetric soil moisture
content, measured for the three soil layers within the A horizon,
showed that it was higher for the top 5 cm over the whole period of
monitoring (15/7/2004 up to 10/11/05) with the variation becoming
greater during winter time. This reflects the pattern of rainfall in
Ireland which is spread over the whole year and shows that light
rainfall events during summer time were compensated by loss
through evapotranspiration, but only in the top 5 cm of soil. This
layer had the highest porosity and highest moisture holding capacity
due to the high content of organic matter. The gravimetric soil
moisture contents of the top 5 cm and the underlying 5-15 and 15-25
cm layers show that bottom site of the Hill Field had higher soil
moisture content than the middle and top sites during the whole
period of monitoring.
Abstract: Above Elbow Prosthesis is one of the most commonly
amputated or missing limbs. The research is done for modelling
techniques of upper limb prosthesis and design of high torque, light
weight and compact in size elbow actuator. The purposed actuator
consists of a DC motor, planetary gear set and a harmonic drive. The
calculations show that the actuator is good enough to be used in real
life powered prosthetic upper limb or rehabilitation exoskeleton.
Abstract: This paper presents a compact thermoelectric power generator system based on temperature difference across the element. The system can transfer the burning heat energy to electric energy directly. The proposed system has a thermoelectric generator and a power control box. In the generator, there are 4 thermoelectric modules (TEMs), each of which uses 2 thermoelectric chips (TEs) and 2 cold sinks, 1 thermal absorber, and 1 thermal conduction flat board. In the power control box, there are 1 storing energy device, 1 converter, and 1 inverter. The total net generating power is about 11W. This system uses commercial portable gas stoves or burns timber or the coal as the heat source, which is easily obtained. It adopts solid-state thermoelectric chips as heat inverter parts. The system has the advantages of being light-weight, quite, and mobile, requiring no maintenance, and havng easily-supplied heat source. The system can be used a as long as burning is allowed. This system works well for highly-mobilized outdoors situations by providing a power for illumination, entertainment equipment or the wireless equipment at refuge. Under heavy storms such as typhoon, when the solar panels become ineffective and the wind-powered machines malfunction, the thermoelectric power generator can continue providing the vital power.
Abstract: Over half of the total electricity consumption is used in buildings. Air-conditioning and electric lighting are the two main resources of electricity consumption in high rise buildings. One way to reduce electricity consumption would be to limit heat gain into buildings, therefore reduce the demand for air-conditioning during hot summer months especially in hot regions. On the other hand natural daylight can be used to reduce the use of electricity for artificial lighting. In this paper effective factors on minimizing heat gain and achieving required day light were reviewed .As daylight always accompanied by solar heat gain. Also interactions between heat gain and daylight were discussed through previous studies and equations which are related to heat gain and day lighting especially in high rise buildings. As a result importance of building-s form and its component on energy consumption in buildings were clarified.
Abstract: In cancer progress, the optical properties of tissues
like absorption and scattering coefficient change, so by these
changes, we can trace the progress of cancer, even it can be applied
for pre-detection of cancer. In this paper, we investigate the effects of
changes of optical properties on light penetrated into tissues. The
diffusion equation is widely used to simulate light propagation into
biological tissues. In this study, the boundary integral method (BIM)
is used to solve the diffusion equation. We illustrate that the changes
of optical properties can modified the reflectance or penetrating light.
Abstract: Off-grid Photovoltaic (PV) systems are empowering
technology in underdeveloped countries like Ethiopia where many
people live far away from the modern world. Where there is
relatively low energy consumption, providing energy from grid
systems is not commercially cost-effective. As a result, significant
people groups worldwide stay without access to electricity. One
remote village in northern Ethiopia was selected by the United
Nations for a pilot project to improve its living conditions. As part of
this comprehensive project, an intelligent charge controller circuit for
Off-grid PV systems was designed for the clinic in that village. In
this paper, design aspects of an intelligent charge controller unit and
its load driver circuits are discussed for an efficient utilization of PVbased
supply systems.
Abstract: LES with mixed subgrid-scale model has been used to
simulate aerodynamic performance of hypersonic configuration. The
simulation was conducted to replicate conditions and geometry of a
model which has been previously tested. LES Model has been
successful in predict pressure coefficient with the max error 1.5%
besides afterbody. But in the high Mach number condition, it is poor in
predict ability and product 12.5% error. The calculation error are
mainly conducted by the distribution swirling. The fact of poor ability
in the high Mach number and afterbody region indicated that the
mixed subgrid-scale model should be improved in large eddied
especially in hypersonic separate region. In the condition of attach and
sideslip flight, the calculation results have waves. LES are successful
in the prediction the pressure wave in hypersonic flow.
Abstract: This study aims at investigating factors in research
and development (R&D) growth and exploring the role of R&D
management in enhancing social innovation and productivity
improvement in Iran-s industrial sector. It basically explores the
common types of R&D activities and the industries which benefited
the most from active R&D units in Iran. The researchers generated
qualitative analyses obtained from primary and secondary data.
The primary data have been retrieved through interviews with five
key players (Managing Director, Internal Manager, General Manager,
Executive Manager, and Project Manager) in the industrial sector.
The secondary data acquired from an investigation on Mazandaran, a
province of northern Iran. The findings highlight Iran-s focuses of R
& D on cost reduction and upgrading productivity. Industries that
have benefited the most from active R&D units are metallic,
machinery and equipment design, and automotive.
We rank order the primary effects of R&D on productivity
improvement as follows, industry improvement, economic growth,
using professional human resources, generating productivity and
creativity culture, creating a competitive and innovative environment,
and increasing people-s knowledge.
Generally, low budget dedication and insufficient supply of highly
skilled scientists and engineers are two important obstacles for R&D
in Iran. Whereas, R&D has resulted in improvement in Iranian
society, transfer of contemporary knowledge into the international
market is still lacking.
Abstract: In the present work, behavior of inoxydable steel as
reinforcement bar in composite concrete is being investigated. The
bar-concrete adherence in reinforced concrete (RC) beam is studied
and focus is made on the tension stiffening parameter. This study
highlighted an approach to observe this interaction behavior in
bending test instead of direct tension as per reported in many
references. The approach resembles actual loading condition of the
structural RC beam. The tension stiffening properties are then
applied to numerical finite element analysis (FEA) to verify their
correlation with laboratory results. Comparison with laboratory
shows a good correlation between the two. The experimental settings
is able to determine tension stiffening parameters in RC beam and
the modeling strategies made in ABAQUS can closely represent the
actual condition. Tension stiffening model used can represent the
interaction properties between inoxydable steel and concrete.
Abstract: This paper presents an inexpensive and effective temperature-controlled chamber for temperature environment tests of Organic Light Emitting Diode (OLED) panels. The proposed chamber is a compact warmer and cooler with an exact temperature control system. In the temperature-controlled space of the chamber, thermoelectric modules (TEMs) are utilized to cool or to heat OLED panels, novel fixtures are designed to flexibly clamp the OLED panels of different size, and special connectors for wiring between the OLED panels and the test instrument are supplied. The proposed chamber has the following features. (1) The TEMs are solid semi-conductive devices, so they operate without noise and without pollution. (2) The volume of the temperature-controlled space of the chamber about 160mm*160mm*120mm, so the chamber are compact and easy to move. (3) The range of the controlled temperatures is from -10 oC to +80 oC, and the precision is ?0.5 oC. (4) The test instrument can conveniently and easily measure the OLED panels via the novel fixtures and special connectors. In addition to a constant temperature being maintained in the chamber, a temperature shock experiments can run for a long time. Therefore, the chamber will be convenient and useful for temperature environment tests of OLED panels.
Abstract: Client expectations and preferences about therapy
represent an important area of investigation as research shows they
are linked to engagement in therapy and therapy outcomes. Studies
examining young people-s expectations and preferences of therapy
remain a neglected area of research. The present study explored what
expectations and preferences young people seeking professional help
held regarding: their role as a client, their therapist-s role, their
therapeutic outcomes, and the processes of therapy. Gender and age
differences were also examined. Participants included 188 young
people aged 12-25 who completed a survey while attending their
initial session at a youth mental health service. Data were analysed
using quantitative methods. Results found the young people held
significantly more pessimistic expectations around therapy when
compared to what they had wanted therapy to be like. Few age and
gender differences were found. Results highlight the importance of a
collaborative therapy approach when working with young people.
Abstract: Three-dimensional reconstruction of small objects has
been one of the most challenging problems over the last decade.
Computer graphics researchers and photography professionals have
been working on improving 3D reconstruction algorithms to fit the
high demands of various real life applications. Medical sciences,
animation industry, virtual reality, pattern recognition, tourism
industry, and reverse engineering are common fields where 3D
reconstruction of objects plays a vital role. Both lack of accuracy and
high computational cost are the major challenges facing successful
3D reconstruction. Fringe projection has emerged as a promising 3D
reconstruction direction that combines low computational cost to both
high precision and high resolution. It employs digital projection,
structured light systems and phase analysis on fringed pictures.
Research studies have shown that the system has acceptable
performance, and moreover it is insensitive to ambient light.
This paper presents an overview of fringe projection approaches. It
also presents an experimental study and implementation of a simple
fringe projection system. We tested our system using two objects
with different materials and levels of details. Experimental results
have shown that, while our system is simple, it produces acceptable
results.
Abstract: Students in high education are presented with new terms and concepts in nearly every lecture they attend. Many of them prefer Web-based self-tests for evaluation of their concepts understanding since they can use those tests independently of tutors- working hours and thus avoid the necessity of being in a particular place at a particular time. There is a large number of multiple-choice tests in almost every subject designed to contribute to higher level learning or discover misconceptions. Every single test provides immediate feedback to a student about the outcome of that test. In some cases a supporting system displays an overall score in case a test is taken several times by a student. What we still find missing is how to secure delivering of personalized feedback to a user while taking into consideration the user-s progress. The present work is motivated to throw some light on that question.
Abstract: Minor problems arising from optimizations by
welding of fixed prostheses frameworks can be identified by
macroscopic and microscopic visual inspection. The purpose of this
study was to highlight the visible discontinuities present in the laser
welds of dental Ni-Cr alloys. Ni-Cr base metal alloys designated for
fixed prostheses manufacture were selected for the experiments.
Using cast plates, preliminary tests were conducted by laser welding.
Macroscopic visual inspection was done carefully to assess the
defects of the welding rib. Electron microscopy images allowed
visualization of small discontinuities, which escapes visual
inspection. Making comparison to Ni-Cr alloys taken in the
experiment and laser welded, after visual analysis, the best welds
appear for Heraenium NA alloy.
Abstract: Design and evaluation of reciprocating compressors
should include a pulsation study. The object is to ensure that
predicted pulsation levels meet guidelines to limit vibration, shaking
forces, noise, associated pressure drops, horsepower losses and
fabrication cost and time to acceptable levels. This paper explains
procedures and recommendations to select and size pulsation
suppression devices to obtain optimum arrangement in terms of
pulsation, vibration, shaking forces, performance, reliability, safety,
operation, maintenance and commercial conditions. Model and
advanced formulations for pulsation study are presented. The effect
of the full fluid dynamic model on the prediction of pulsation waves
and resulting frequency spectrum distributions are discussed.
Advanced and optimum methods of controlling pulsations are
highlighted. Useful recommendations and guidelines for pulsation
control, piping pulsation analysis, pulsation vessel design, shaking
forces, low pressure drop orifices, pulsation study report and devices
to mitigate pulsation and shaking problems are discussed.
Abstract: Double-diffusive steady convection in a partially
porous cavity with partially permeable walls and under the combined
buoyancy effects of thermal and mass diffusion was analysed
numerically using finite volume method.
The top wall is well insulated and impermeable while the bottom
surface is partially well insulated and impermeable and partially
submitted to constant temperature T1 and concentration C1. Constant
equal temperature T2 and concentration C2 are imposed along the
vertical surfaces of the enclosure. Mass suction/injection and
injection/suction are respectively considered at the bottom of the
porous centred partition and at one of the vertical walls.
Heat and mass transfer characteristics as streamlines and average
Nusselt numbers and Sherwood numbers were discussed for different
values of buoyancy ratio, Rayleigh number, and injection/suction
coefficient.
It is especially noted that increasing the injection factor
disadvantages the exchanges in the case of the injection while the
transfer is augmented in case of suction. On the other hand, a critical
value of the buoyancy ratio was highlighted for which heat and mass
transfers are minimized.
Abstract: This paper present a circular patch microstrip array antenna operate in KU-band (10.9GHz – 17.25GHz). The proposed circular patch array antenna will be in light weight, flexible, slim and compact unit compare with current antenna used in KU-band. The paper also presents the detail steps of designing the circular patch microstrip array antenna. An Advance Design System (ADS) software is used to compute the gain, power, radiation pattern, and S11 of the antenna. The proposed Circular patch microstrip array antenna basically is a phased array consisting of 'n' elements (circular patch antennas) arranged in a rectangular grid. The size of each element is determined by the operating frequency. The incident wave from satellite arrives at the plane of the antenna with equal phase across the surface of the array. Each 'n' element receives a small amount of power in phase with the others. There are feed network connects each element to the microstrip lines with an equal length, thus the signals reaching the circular patches are all combined in phase and the voltages add up. The significant difference of the circular patch array antenna is not come in the phase across the surface but in the magnitude distribution.
Abstract: In the last decades, the problem of perforation
damage has been considered as the major factor for the
reduction of oil productivity. Underbalance perforation is
considered as one of the best means to minimize or overcome
this problem. By maintaining wellbore pressure lower than
formation pressure, perforation damage could be minimize or
eliminated. This can be achieved by the use of nontraditional
lightweight completion fluid. This paper presents the effect of
natural clay in formulating nontraditional completion fluid to
ensure successful perforation job and increase of production
rate. Natural clay is used as homogenizing agent to create a
stable and non-damaging low-density completion fluid.
Results indicate that the addition of natural clay dramatically
increase the stability of the final fluids. In addition, field test
has shown that the application of nontraditional completion
fluid increases oil production by three folds.
Abstract: The purpose of this study was to assess the value of Second Life among post-secondary instructors with experience using Second Life as an educational tool. Using Everett Rogers-s diffusion of innovations theory, survey respondents (N = 162), were divided into three adopter categories: innovators, early adopters and the early majority. Respondents were from 15 countries and 25 academic disciplines, indicating the considerable potential this innovation has to be adopted across many different borders and in many areas of academe. Nearly 94% of respondents said they plan to use Second Life again as an educational tool. However, no significant differences were found in instructors- levels of satisfaction with Second Life as an educational tool or their perceived effect on student learning across adopter categories. On the other hand, instructors who conducted class fully in Second Life were significantly more satisfied than those who used Second Life as only a small supplement to a real-world class. Overall, personal interest factors, rather than interpersonal communication factors, most influenced respondents- decision to adopt Second Life as an educational tool. In light of these findings, theoretical implications are discussed and practical suggestions are provided.