Abstract: High Power Lasers produce an intense burst of
Bremmstrahlung radiation which has potential applications in broadband
x-ray radiography. Since the radiation produced is through the
interaction of accelerated electrons with the remaining laser target,
these bursts are extremely short – in the region of a few ps. As a
result, the laser-produced x-rays are capable of imaging complex
dynamic objects with zero motion blur.
Abstract: In this paper, Fabless Prototyping Methodology is
introduced for the design and analysis of MEMS devices.
Conventionally Finite Element Analysis (FEA) is performed before
system level simulation. In our proposed methodology, system level
simulation is performed earlier than FEA as it is computationally less
extensive and low cost. System level simulations are based on
equivalent behavioral models of MEMS device. Electrostatic
actuation based MEMS Microgripper is chosen as case study to
implement this methodology. This paper addresses the behavioral
model development and simulation of actuator part of an
electrostatically actuated Microgripper. Simulation results show that
the actuator part of Microgripper works efficiently for a voltage range
of 0-45V with the corresponding jaw displacement of 0-4.5425μm.
With some minor changes in design, this range can be enhanced to
15μm at 85V.
Abstract: PPG is a potential tool in clinical applications. Among such, the relationship between respiration and PPG signal has attracted attention in past decades. In this research, a bivariate AR spectral estimation method was utilized for the coherence analysis between these two signals. Ten healthy subjects participated in this research with signals measured at different respiratory rates. The results demonstrate that high coherence exists between respiration and PPG signal, whereas the coherence disappears in breath-holding experiments. These results imply that PPG signal reveals the respiratory information. The utilized method may provide an attractive alternative approach for the related researches.
Abstract: The migration-environment nexus has gained increased interest from the social research field over the last years. While straightly connected to human security issues, this theme has pervaded through the media to the public sphere. Therefore, it is important to observe how did the discussions over environmentally induced migrations develop from the scientific basis to the media attention, passing through some political voices, and in which ways might these messages be interpreted within the broader public discourses. To achieve this purpose, the analysis of the press entries between 2004 and 2010 in three of the main Portuguese newspapers shall be presented, specially reflecting upon the events, protagonists, topics, geographical attributions and terms/expressions used to define those who migrate due to environmental degradation or disasters.
Abstract: Implementing Information Technology/ Information
System (IT/IS) is critical for every industry as its potential benefits
have been to motivate many industries including the Malaysian
construction industry to invest in it. To successfully implement IT/IS
has become the major concern for every organisation. Identifying the
critical success factors (CSFs) has become the main agenda for
researchers, academicians and practitioners due to the wide number
of failures reported. This research paper seeks to identify the CSFs
that influence the successful implementation of IT/IS in construction
industry in Malaysia. Limited factors relating to people issue will be
highlighted here to showcase some as it becomes one of the major
contributing factors to the failure. Three (3) organisations have
participated in this study. Semi-structured interviews are employed as
they offer sufficient flexibility to ensure that all relevant factors are
covered. Several key issues contributing to successful
implementations of IT/IS are identified. The results of this study
reveal that top management support, communication, user
involvement, IT staff roles and responsibility, training/skills, leader/
IT Leader, organisation culture, knowledge/ experience, motivation,
awareness, focus and ambition, satisfaction, teamwork/ collaboration,
willingness to change, attitude, commitment, management style,
interest in IT, employee behaviour towards collaborative
environment, trust, interpersonal relationship, personal characteristic
and competencies are significantly associated with the successful
implementations of IT/IS. It is anticipated that this study will create
awareness and contribute to a better understanding amongst
construction industry players and will assist them to successfully
implement IT/IS.
Abstract: Circular tubes have been widely used as structural
members in engineering application. Therefore, its collapse behavior
has been studied for many decades, focusing on its energy absorption
characteristics. In order to predict the collapse behavior of members,
one could rely on the use of finite element codes or experiments.
These tools are helpful and high accuracy but costly and require
extensive running time. Therefore, an approximating model of tubes
collapse mechanism is an alternative for early step of design. This
paper is also aimed to develop a closed-form solution of thin-walled
circular tube subjected to bending. It has extended the Elchalakani et
al.-s model (Int. J. Mech. Sci.2002; 44:1117-1143) to include the
rate of energy dissipation of rolling hinge in the circumferential
direction. The 3-D geometrical collapse mechanism was analyzed by
adding the oblique hinge lines along the longitudinal tube within the
length of plastically deforming zone. The model was based on the
principal of energy rate conservation. Therefore, the rates of internal
energy dissipation were calculated for each hinge lines which are
defined in term of velocity field. Inextensional deformation and
perfect plastic material behavior was assumed in the derivation of
deformation energy rate. The analytical result was compared with
experimental result. The experiment was conducted with a number of
tubes having various D/t ratios. Good agreement between analytical
and experiment was achieved.
Abstract: The hydrodynamic processes in bubbly liquid flowing
in tubes and nozzles are studied theoretically and numerically. The
principal regularities of non-stationary processes of boiling liquid
outflow are established under conditions of experiments when the
depressurization of a tube with high pressure inside occurs. The
steady-state solution of bubbly liquid flow in the nozzle of round
cross section with high pressure and temperature conditions inside
bubbles is studied accounting for phase transition and chemical
reactions.
Abstract: Widespread use of asbestos over the last century has left a terrible legacy of lung disease. Doctors knew of the health risks long ago, but almost nothing was done to protect workers and the public. Some aspects of nanotechnology may have risks similar to asbestos.
Abstract: Foodborne Salmonella infections have become a
major problem world wide. Salmonellosis transmitted from fish are
quite common. Established quality control measures exist for export
oriented fish, none exists for fish consumed locally. This study aimed
at characterization of Salmonella isolated from Nile tilapia . The
study was carried out in selected beaches along L. Victoria in
Western Kenya between March and June 2007. One hundred and
twenty fish specimens were collected. Salmonella isolates were
confirmed using serotyping, biochemical testing in addition to malic
acid dehydrogenase (mdh) and fliC gene sequencing. Twenty
Salmonella isolates were confirmed by mdh gene sequencing. Nine
(9) were S. enterica serotype typhimurium, four (4) were S. enterica
Serotype, enteritidis and seven (7) were S. enterica serotype typhi.
Nile tilapia have a role in transmission of Salmonellosis in the study
area, poor sanitation was a major cause of pollution at the beach
inshore waters.
Abstract: Globalisation is a phenomenon that cannot be avoided.
As globalisation allowed free flow of inputs including labour, it may
affect job opportunities for the locals. Therefore, investigate the
determinants of labour supply is essential in understanding the
structure of labour market in the new era of globalization. The
objective of this article is to examine labour supply by taking into
account the globalisation effect. The study covers 3885 households in
Peninsular Malaysia who are chosen using stratified random
sampling. The labour supply model will be the basis for the analysis.
The basic labour supply determinants are own wage and non-labour
income. However, the extended labour supply model incorporates
other variables like spouse wage，number of children and
individuals characteristics like education level and age. Besides, the
globalization indicator will also be incorporated as another
independent variable.
Abstract: Multidrug resistant organisms have been taunting the
medical world for the last few decades. Even with new antibiotics
developed, resistant strains have emerged soon after. With the
advancement of nanotechnology, we investigated colloidal silver
nanoparticles for its antimicrobial activity against Pseudomonas
aeruginosa. This organism is a multidrug resistant which contributes
to the high morbidity and mortality in immunocompromised patients.
Five multidrug resistant strains were used in this study. The
antimicrobial effect was studied using the disc diffusion and broth
dilution techniques. An inhibition zone of 11 mm was observed with
10 μg dose of the nanoparticles. The nanoparticles exhibited MIC of
50 μg/ml when added at the lag phase and the subinhibitory
concentration was measured as 100 μg/ml. The MIC50 value showed
to be 15 μg/ml. This study suggests that silver nanoparticles can be
further developed as an antimicrobial agent, hence decreasing the
burden of the multidrug resistance phenomena.
Abstract: This paper addresses the problem of peak-to-average
power ratio (PAPR) in orthogonal frequency division multiplexing
(OFDM) systems. It also introduces a new PAPR reduction technique
based on adaptive square-rooting (SQRT) companding process. The
SQRT process of the proposed technique changes the statistical
characteristics of the OFDM output signals from Rayleigh
distribution to Gaussian-like distribution. This change in statistical
distribution results changes of both the peak and average power
values of OFDM signals, and consequently reduces significantly the
PAPR. For the 64QAM OFDM system using 512 subcarriers, up to 6
dB reduction in PAPR was achieved by square-rooting technique
with fixed degradation in bit error rate (BER) equal to 3 dB.
However, the PAPR is reduced at the expense of only -15 dB out-ofband
spectral shoulder re-growth below the in-band signal level. The
proposed adaptive SQRT technique is superior in terms of BER
performance than the original, non-adaptive, square-rooting
technique when the required reduction in PAPR is no more than 5
dB. Also, it provides fixed amount of PAPR reduction in which it is
not available in the original SQRT technique.
Abstract: Many organisations are nowadays interested to adopt
lean manufacturing strategy that would enable them to compete in
this competitive globalisation market. In this respect, it is necessary
to assess the implementation of lean manufacturing in different
organisations so that the important best practices can be identified.
This paper describes the development of key areas which will be
used to assess the adoption and implementation of lean
manufacturing practices. There are some key areas developed to
evaluate and reduce the most optimal projects so as to enhance their
production efficiency and increase the purpose of the economic
benefits of the manufacturing unit.
Lean manufacturing is becoming lean enterprise by treating its
customers and suppliers as partners. This gives the extra edge in
today-s cost and time competitive markets. The organisation is
becoming strong in all the conventional competition points. They are
Price, Quality and Delivery. Lean enterprise owners can deliver high
quality products quickly, with low price.
Abstract: With getting older in the whole population, the
prevalence of stroke and its residual disability is getting higher and
higher recently in Taiwan. The functional electrical stimulation
cycling system (FESCS) is useful for hemiplegic patients. Because
that the muscle of stroke patients is under hybrid activation. The raw
electromyography (EMG) represents the residual muscle force of
stroke subject whereas the peak-to-peak of stimulus EMG indicates the
force enhancement benefiting from ES. It seems that EMG signals
could be used for a parameter of feedback control mechanism. So, we
design the feedback control protocol of FESCS, it includes
physiological signal recorder, FPGA biomedical module, DAC and
electrical stimulation circuit. Using the intensity of real-time EMG
signal obtained from patients, as a feedback control method for the
output voltage of FES-cycling system.
Abstract: Robots- visual perception is a field that is gaining
increasing attention from researchers. This is partly due to emerging
trends in the commercial availability of 3D scanning systems or
devices that produce a high information accuracy level for a variety of
applications. In the history of mining, the mortality rate of mine workers
has been alarming and robots exhibit a great deal of potentials to
tackle safety issues in mines. However, an effective vision system
is crucial to safe autonomous navigation in underground terrains.
This work investigates robots- perception in underground terrains
(mines and tunnels) using statistical region merging (SRM) model.
SRM reconstructs the main structural components of an imagery
by a simple but effective statistical analysis. An investigation is
conducted on different regions of the mine, such as the shaft, stope
and gallery, using publicly available mine frames, with a stream of
locally captured mine images. An investigation is also conducted on a
stream of underground tunnel image frames, using the XBOX Kinect
3D sensors. The Kinect sensors produce streams of red, green and
blue (RGB) and depth images of 640 x 480 resolution at 30 frames per
second. Integrating the depth information to drivability gives a strong
cue to the analysis, which detects 3D results augmenting drivable and
non-drivable regions in 2D. The results of the 2D and 3D experiment
with different terrains, mines and tunnels, together with the qualitative
and quantitative evaluation, reveal that a good drivable region can be
detected in dynamic underground terrains.
Abstract: The rapid pace of technological advancement and its
consequential widening digital divide has resulted in the
marginalization of the disabled especially the communication
challenged. The dearth of suitable technologies for the development
of assistive technologies has served to further marginalize the
communications challenged user population and widen this chasm
even further. Given the varying levels of disability there and its
associated requirement for customized solution based. This paper
explains the use of a Software Development Kits (SDK) for the
bridging of this communications divide through the use of industry
poplar communications SDKs towards identification of requirements
for communications challenged users as well as identification of
appropriate frameworks for future development initiatives.
Abstract: The study identified the sources of production
inefficiency of the farming sector in district Faisalabad in the Punjab
province of Pakistan. Data Envelopment Analysis (DEA) technique
was utilized at farm level survey data of 300 farmers for the year
2009. The overall mean efficiency score was 0.78 indicating 22
percent inefficiency of the sample farmers. Computed efficiency
scores were then regressed on farm specific variables using Tobit
regression analysis. Farming experience, education, access to
farming credit, herd size and number of cultivation practices showed
constructive and significant effect on the farmer-s technical
efficiency.
Abstract: Diffuse viral encephalitis may lack fever and other cardinal signs of infection and hence its distinction from other acute encephalopathic illnesses is challenging. Often, the EEG changes seen routinely are nonspecific and reflect diffuse encephalopathic changes only. The aim of this study was to use nonlinear dynamic mathematical techniques for analyzing the EEG data in order to look for any characteristic diagnostic patterns in diffuse forms of encephalitis.It was diagnosed on clinical, imaging and cerebrospinal fluid criteria in three young male patients. Metabolic and toxic encephalopathies were ruled out through appropriate investigations. Digital EEGs were done on the 3rd to 5th day of onset. The digital EEGs of 5 male and 5 female age and sex matched healthy volunteers served as controls.Two sample t-test indicated that there was no statistically significant difference between the average values in amplitude between the two groups. However, the standard deviation (or variance) of the EEG signals at FP1-F7 and FP2-F8 are significantly higher for the patients than the normal subjects. The regularisation dimension is significantly less for the patients (average between 1.24-1.43) when compared to the normal persons (average between 1.41-1.63) for the EEG signals from all locations except for the Fz-Cz signal. Similarly the wavelet dimension is significantly less (P = 0.05*) for the patients (1.122) when compared to the normal person (1.458). EEGs are subdued in the case of the patients with presence of uniform patterns, manifested in the values of regularisation and wavelet dimensions, when compared to the normal person, indicating a decrease in chaotic nature.
Abstract: The concentrations of aliphatic and polycyclic aromatic hydrocarbons (PAH) were determined in atmospheric aerosol samples collected at a rural site in Hungary (K-puszta, summer 2008), a boreal forest (Hyytiälä,
April 2007) and a polluted rural area in Italy (San Pietro Capofiume, Po Valley, April 2008). A clear distinction between “clean" and “polluted" periods was observed. Concentrations obtained for Hyytiälä are significantly lower than those for the other two sites. Source reconciliation was performed using diagnostic parameters, such as the carbon preference index and ratios between PAH. The presence of an unresolved complex mixture of hydrocarbons, especially for the Finnish and Italian samples, is indicative of petrogenic inputs. In K-puszta, the aliphatic hydrocarbons are dominated by leaf wax n-alkanes. The long range transport of anthropogenic pollution contributed to the Finnish aerosol. Industrial activities and vehicular emissions represent major sources in San Pietro Capofiume. PAH in K-puszta consist of both pyrogenic and petrogenic compounds.
Abstract: This paper attempts to establish the fact that Multi
State Network Classification is essential for performance
enhancement of Transport protocols over Satellite based Networks. A
model to classify Multi State network condition taking into
consideration both congestion and channel error is evolved. In order
to arrive at such a model an analysis of the impact of congestion and
channel error on RTT values has been carried out using ns2. The
analysis results are also reported in the paper. The inference drawn
from this analysis is used to develop a novel statistical RTT based
model for multi state network classification.
An Adaptive Multi State Proactive Transport Protocol consisting
of Proactive Slow Start, State based Error Recovery, Timeout Action
and Proactive Reduction is proposed which uses the multi state
network state classification model. This paper also confirms through
detail simulation and analysis that a prior knowledge about the
overall characteristics of the network helps in enhancing the
performance of the protocol over satellite channel which is
significantly affected due to channel noise and congestion.
The necessary augmentation of ns2 simulator is done for
simulating the multi state network classification logic. This
simulation has been used in detail evaluation of the protocol under
varied levels of congestion and channel noise. The performance
enhancement of this protocol with reference to established protocols
namely TCP SACK and Vegas has been discussed. The results as
discussed in this paper clearly reveal that the proposed protocol
always outperforms its peers and show a significant improvement in
very high error conditions as envisaged in the design of the protocol.