Abstract: The goal of this research is discovering the
determinants of the success or failure of external cooperation in small
and medium enterprises (SMEs). For this, a survey was given to 190
SMEs that experienced external cooperation within the last 3 years. A
logistic regression model was used to derive organizational or strategic
characteristics that significantly influence whether external
collaboration of domestic SMEs is successful or not. Results suggest
that research and development (R&D) features in general
characteristics (both idea creation and discovering market
opportunities) that focused on and emphasized indirected-market
stakeholders (such as complementary companies and affiliates) and
strategies in innovative strategic characteristics raise the probability of
successful external cooperation. This can be used meaningfully to
build a policy or strategy for inducing successful external cooperation
or to understand the innovation of SMEs.
Abstract: An Artificial Neural Network based modeling
technique has been used to study the influence of different
combinations of meteorological parameters on evaporation from a
reservoir. The data set used is taken from an earlier reported study.
Several input combination were tried so as to find out the importance
of different input parameters in predicting the evaporation. The
prediction accuracy of Artificial Neural Network has also been
compared with the accuracy of linear regression for predicting
evaporation. The comparison demonstrated superior performance of
Artificial Neural Network over linear regression approach. The
findings of the study also revealed the requirement of all input
parameters considered together, instead of individual parameters
taken one at a time as reported in earlier studies, in predicting the
evaporation. The highest correlation coefficient (0.960) along with
lowest root mean square error (0.865) was obtained with the input
combination of air temperature, wind speed, sunshine hours and
mean relative humidity. A graph between the actual and predicted
values of evaporation suggests that most of the values lie within a
scatter of ±15% with all input parameters. The findings of this study
suggest the usefulness of ANN technique in predicting the
evaporation losses from reservoirs.
Abstract: Intelligent deep-drawing is an instrumental research field in sheet metal forming. A set of 28 different experimental data have been employed in this paper, investigating the roles of die radius, punch radius, friction coefficients and drawing ratios for axisymmetric workpieces deep drawing. This paper focuses an evolutionary neural network, specifically, error back propagation in collaboration with genetic algorithm. The neural network encompasses a number of different functional nodes defined through the established principles. The input parameters, i.e., punch radii, die radii, friction coefficients and drawing ratios are set to the network; thereafter, the material outputs at two critical points are accurately calculated. The output of the network is used to establish the best parameters leading to the most uniform thickness in the product via the genetic algorithm. This research achieved satisfactory results based on demonstration of neural networks.
Abstract: Article presents the geometry and structure
reconstruction procedure of the aircraft model for flatter research
(based on the I22-IRYDA aircraft). For reconstruction the Reverse
Engineering techniques and advanced surface modeling CAD tools
are used. Authors discuss all stages of data acquisition process,
computation and analysis of measured data. For acquisition the three
dimensional structured light scanner was used. In the further sections,
details of reconstruction process are present. Geometry
reconstruction procedure transform measured input data (points
cloud) into the three dimensional parametric computer model
(NURBS solid model) which is compatible with CAD systems.
Parallel to the geometry of the aircraft, the internal structure
(structural model) are extracted and modeled. In last chapter the
evaluation of obtained models are discussed.
Abstract: In parallel, broadcasting has changed rapidly with the
changing of the world at the same area. Broadcasting is also
influenced and reshaped in terms of the emergence of new
communication technologies. These developments have resulted a lot
of economic and social consequences. The most important
consequences of these results are those of the powers of the
governments to control over the means of communication and control
mechanisms related to the descriptions of the new issues. For this
purpose, autonomous and independent regulatory bodies have been
established by the state. One of these regulatory bodies is the Radio
and Television Supreme Council, which to be established in 1994,
with the Code no 3984. Today’s Radio and Television Supreme
Council which is responsible for the regulation of the radio and
television broadcasts all across Turkey has an important and effective
position as autonomous and independent regulatory body. The Radio
and Television Supreme Council acts as being a remarkable organizer
for a sensitive area of radio and television broadcasting on one hand,
and the area of democratic, liberal and keep in mind the concept of
the public interest by putting certain principles for the functioning of
the Board control, in the context of media policy as one of the central
organs, on the other hand.
In this study, the role of the Radio and Television Supreme
Council is examined in accordance with the Code no 3894 in order to
control over the communication and control mechanisms as well as
the examination of the changes in the duties of the Code No. 6112,
dated 2011.
Abstract: Salinity level may affect early development of
biofuel feedstock crops. The biofuel feedstock crops canola
(Brassica napus L.), sorghum [Sorghum bicolor (L.) Moench], and
sunflower (Helianthus annuus L.); and the potential feedstock crop
sweet corn (Zea mays L.) were planted in media in pots and treated
with aqueous solutions of 0, 0.1, 0.5 and 1.0 M NaCl once at: 1)
planting; 2) 7-10 days after planting or 3) first true leaf expansion.
An additional treatment (4) comprised of one-half strength of the 0.1,
0.5 and 1.0 M (concentrations 0.05, 0.25, 0.5 M at each application)
was applied at first true leaf expansion and four days later. Survival
of most crops decreased below 90% above 0.5 M; survival of canola
decreased above 0.1 M. Application timing had little effect on crop
survival. For canola root fresh and dry weights improved when
application was at plant emergence; for sorghum top and root fresh
weights improved when the split application was used. When
application was at planting root dry weight was improved over most
other applications. Sunflower top fresh weight was among the
highest when saline solutions were split and top dry weight was
among the highest when application was at plant emergence. Sweet
corn root fresh weight was improved when the split application was
used or application was at planting. Sweet corn root dry weight was
highest when application was at planting or plant emergence. Even at
high salinity rates survival rates greater than what might be expected
occurred. Plants that survived appear to be able to adjust to saline
during the early stages of development.
Abstract: In this paper, we first consider the quality of service
problems in heterogeneous wireless networks for sending the video
data, which their problem of being real-time is pronounced. At last,
we present a method for ensuring the end-to-end quality of service at
application layer level for adaptable sending of the video data at
heterogeneous wireless networks. To do this, mechanism in different
layers has been used. We have used the stop mechanism, the
adaptation mechanism and the graceful degrade at the application
layer, the multi-level congestion feedback mechanism in the network
layer and connection cutting off decision mechanism in the link
layer. At the end, the presented method and the achieved
improvement is simulated and presented in the NS-2 software.
Abstract: Modern information and communication technologies
offer a variety of support options for the efficient handling of
customer relationships. CRM systems have been developed, which
are designed to support the processes in the areas of marketing, sales
and service. Along with technological progress, CRM systems are
constantly changing, i.e. the systems are continually enhanced by
new functions. However, not all functions are suitable for every
company because of different frameworks and business processes. In
this context the question arises whether or not CRM systems are
widely used in Austrian companies and which business processes are
most frequently supported by CRM systems. This paper aims to shed
light on the popularity of CRM systems in Austrian companies in
general and the use of different functions to support their daily
business. First of all, the paper provides a theoretical overview of the
structure of modern CRM systems and proposes a categorization of
currently available software functionality for collaborative,
operational and analytical CRM processes, which provides the
theoretical background for the empirical study. Apart from these
theoretical considerations, the paper presents the empirical results of
a field survey on the use of CRM systems in Austrian companies and
analyzes its findings.
Abstract: From a set of shifted, blurred, and decimated image , super-resolution image reconstruction can get a high-resolution image. So it has become an active research branch in the field of image restoration. In general, super-resolution image restoration is an ill-posed problem. Prior knowledge about the image can be combined to make the problem well-posed, which contributes to some regularization methods. In the regularization methods at present, however, regularization parameter was selected by experience in some cases and other techniques have too heavy computation cost for computing the parameter. In this paper, we construct a new super-resolution algorithm by transforming the solving of the System stem Є=An into the solving of the equations X+A*X-1A=I , and propose an inverse iterative method.
Abstract: Simultaneous recovery of copper and DCA from
simulated MEUF concentrated stream was investigated. Effects of
surfactant (DCA) and metal (copper) concentrations, surfactant to
metal molar ratio (S/M ratio), electroplating voltage, EDTA
concentration, solution pH, and salt concentration on metal recovery
and current efficiency were studied. Electric voltage of -0.5 V was
shown to be optimum operation condition in terms of Cu recovery,
current efficiency, and surfactant recovery. Increasing Cu recovery and
current efficiency were observed with increases of Cu concentration
while keeping concentration of DCA constant. However, increasing
both Cu and DCA concentration while keeping S/M ratio constant at
2.5 showed detrimental effect on Cu recovery at DCA concentration
higher than 15 mM. Cu recovery decreases with increasing pH while
current efficiency showed an opposite trend. It is believed that
conductivity is the main cause for discrepancy of Cu recovery and
current efficiency observed at different pH. Finally, it was shown that
EDTA had adverse effect on both Cu recovery and current efficiency
while addition of NaCl salt had negative impact on current efficiency
at concentration higher than 8000 mg/L.
Abstract: With the exponential growth of networked system and
application such as eCommerce, the demand for effective internet
security is increasing. Cryptology is the science and study of systems
for secret communication. It consists of two complementary fields of
study: cryptography and cryptanalysis. The application of genetic
algorithms in the cryptanalysis of knapsack ciphers is suggested by
Spillman [7]. In order to improve the efficiency of genetic algorithm
attack on knapsack cipher, the previously published attack was
enhanced and re-implemented with variation of initial assumptions
and results are compared with Spillman results. The experimental
result of research indicates that the efficiency of genetic algorithm
attack on knapsack cipher can be improved with variation of initial
assumption.
Abstract: Global Software Development (GSD) projects are
passing through different boundaries of a company, country and even
in other continents where time zone differs between both sites.
Beside many benefits of such development, research declared plenty
of negative impacts on these GSD projects. It is important to
understand problems which may lie during the execution of GSD
project with different time zones. This research project discussed and
provided different issues related to time delays in GSD projects. In
this paper, authors investigated some of the time delay factors which
usually lie in GSD projects with different time zones. This
investigation is done through systematic review of literature.
Furthermore, the practices to overcome these delay factors which
have already been reported in literature and GSD organizations are
also explored through literature survey and case studies.
Abstract: The main purpose of the dam is to control the surface
streams and rivers across the country. Dam construction and
formation of river and big water reservoirs and resources happen in
the glen is a big incident which would change its surrounding area
considerably. In fact, constructing a dam the glen width is close and
fishes don't migrate from upstream to downstream and ultimately it
would led to their death. To resolve this, it seems necessity to create a
passage for fishes during the construction of dam. It is provided
establishing a set of stepped pools overlooking each other as a fish
way or fish ladder a proper pathway for moving fishes. In this article
we first examine the surrounding environment and then Ghazal Ozon
River and preserving the aquatics.
Abstract: Faced with social and health system capacity
constraints and rising and changing demand for welfare services,
governments and welfare providers are increasingly relying on
innovation to help support and enhance services. However, the
evidence reported by several studies indicates that the realization of
that potential is not an easy task. Innovations can be deemed
inherently complex to implement and operate, because many of them
involve a combination of technological and organizational renewal
within an environment featuring a diversity of stakeholders. Many
public welfare service innovations are markedly systemic in their
nature, which means that they emerge from, and must address, the
complex interplay between political, administrative, technological,
institutional and legal issues. This paper suggests that stakeholders
dealing with systemic innovation in welfare services must deal with
ambiguous and incomplete information in circumstances of
uncertainty. Employing a literature review methodology and case
study, this paper identifies, categorizes and discusses different
aspects of the uncertainty of systemic innovation in public welfare
services, and argues that uncertainty can be classified into eight
categories: technological uncertainty, market uncertainty,
regulatory/institutional uncertainty, social/political uncertainty,
acceptance/legitimacy uncertainty, managerial uncertainty, timing
uncertainty and consequence uncertainty.
Abstract: Currently, the Malaysian construction industry is
focusing on transforming construction processes from conventional
building methods to the Industrialized Building System (IBS). Still,
research on the decision making of IBS technology adoption with the
influence of contextual factors is scarce. The purpose of this paper is
to explore how contextual factors influence the IBS decision making
in building projects which is perceived by those involved in
construction industry namely construction stakeholders and IBS
supply chain members. Theoretical background, theoretical
frameworks and literatures which identify possible contextual factors
that influence decision making towards IBS technology adoption are
presented. This paper also discusses the importance of contextual
factors in IBS decision making, highlighting some possible crossover
benefits and making some suggestions as to how these can be
utilized. Conclusions are drawn and recommendations are made with
respect to the perception of socio-economic, IBS policy and IBS
technology associated with building projects.
Abstract: Computer languages are usually lumped together
into broad -paradigms-, leaving us in want of a finer classification
of kinds of language. Theories distinguishing between -genuine
differences- in language has been called for, and we propose that
such differences can be observed through a notion of expressive mode.
We outline this concept, propose how it could be operationalized and
indicate a possible context for the development of a corresponding
theory. Finally we consider a possible application in connection
with evaluation of language revision. We illustrate this with a case,
investigating possible revisions of the relational algebra in order to
overcome weaknesses of the division operator in connection with
universal queries.
Abstract: Hydrogen is an important chemical in many industries
and it is expected to become one of the major fuels for energy
generation in the future. Unfortunately, hydrogen does not exist in its
elemental form in nature and therefore has to be produced from
hydrocarbons, hydrogen-containing compounds or water.
Above its critical point (374.8oC and 22.1MPa), water has lower
density and viscosity, and a higher heat capacity than those of
ambient water. Mass transfer in supercritical water (SCW) is
enhanced due to its increased diffusivity and transport ability. The
reduced dielectric constant makes supercritical water a better solvent
for organic compounds and gases. Hence, due to the aforementioned
desirable properties, there is a growing interest toward studies
regarding the gasification of organic matter containing biomass or
model biomass solutions in supercritical water.
In this study, hydrogen and biofuel production by the catalytic
gasification of 2-Propanol in supercritical conditions of water was
investigated. Pt/Al2O3and Ni/Al2O3were the catalysts used in the
gasification reactions. All of the experiments were performed under a
constant pressure of 25MPa. The effects of five reaction temperatures
(400, 450, 500, 550 and 600°C) and five reaction times (10, 15, 20,
25 and 30 s) on the gasification yield and flammable component
content were investigated.
Abstract: This paper solves the environmental/ economic dispatch
power system problem using the Non-dominated Sorting Genetic
Algorithm-II (NSGA-II) and its hybrid with a Convergence Accelerator
Operator (CAO), called the NSGA-II/CAO. These multiobjective
evolutionary algorithms were applied to the standard IEEE 30-bus
six-generator test system. Several optimization runs were carried out
on different cases of problem complexity. Different quality measure
which compare the performance of the two solution techniques were
considered. The results demonstrated that the inclusion of the CAO
in the original NSGA-II improves its convergence while preserving
the diversity properties of the solution set.
Abstract: Collaborative working environments for distance
education can be considered as a more generic form of contemporary
remote labs. At present, the majority of existing real laboratories are
not constructed to allow the involved participants to collaborate in
real time. To make this revolutionary learning environment possible
we must allow the different users to carry out an experiment
simultaneously. In recent times, multi-user environments are
successfully applied in many applications such as air traffic control
systems, team-oriented military systems, chat-text tools, multi-player
games etc. Thus, understanding the ideas and techniques behind these
systems could be of great importance in the contribution of ideas to
our e-learning environment for collaborative working. In this
investigation, collaborative working environments from theoretical
and practical perspectives are considered in order to build an
effective collaborative real laboratory, which allows two students or
more to conduct remote experiments at the same time as a team. In
order to achieve this goal, we have implemented distributed system
architecture, enabling students to obtain an automated help by either
a human tutor or a rule-based e-tutor.
Abstract: In this paper we discuss the effect of unbounded particle interaction operator on particle growth and we study how this can address the choice of appropriate time steps of the numerical simulation. We provide also rigorous mathematical proofs showing that large particles become dominating with increasing time while small particles contribute negligibly. Second, we discuss the efficiency of the algorithm by performing numerical simulations tests and by comparing the simulated solutions with some known analytic solutions to the Smoluchowski equation.