Abstract: To study the impact of the inter-module ventilation (IMV) on the space station, the Computational Fluid Dynamic (CFD) model under the influence of IMV, the mathematical model, boundary conditions and calculation method are established and determined to analyze the influence of IMV on cabin air flow characteristics and velocity distribution firstly; and then an integrated overall thermal mathematical model of the space station is used to consider the impact of IMV on thermal management. The results show that: the IMV has a significant influence on the cabin air flow, the flowrate of IMV within a certain range can effectively improve the air velocity distribution in cabin, if too much may lead to its deterioration; IMV can affect the heat deployment of the different modules in space station, thus affecting its thermal management, the use of IMV can effectively maintain the temperature levels of the different modules and help the space station to dissipate the waste heat.
Abstract: This study carried out in order to investigate the
effects of salinity on carbon isotope discrimination (Δ) of shoots and
roots of four sugar beet cultivars (cv) including Madison (British
origin) and three Iranian culivars (7233-P12, 7233-P21 and 7233-P29).
Plants were grown in sand culture medium in greenhouse conditions.
Plants irrigated with saline water (tap water as control, 50 mM, 150
mM, 250 mM and 350 mM of NaCl + CaCl2 in 5 to 1 molar ratio)
from 4 leaves stage for 16 weeks. Carbon isotope discrimination
significantly decreased with increasing salinity. Significant
differences of Δ between shoot and root were observed in all cvs and
all levels of salinity. Madison cv showed lower Δ in shoot and root
than other three cvs at all levels of salinity expect control, but cv
7233-P29 had significantly higher Δ values at saline conditions of 150
mM and above. Therefore, Δ might be applicable, as a useful tool, for
study of salinity tolerance of sugar beet genotypes.
Abstract: In April 2009, a new variant of Influenza A virus
subtype H1N1 emerged in Mexico and spread all over the world. The
influenza has three subtypes in human (H1N1, H1N2 and H3N2)
Types B and C influenza tend to be associated with local or regional
epidemics. Preliminary genetic characterization of the influenza
viruses has identified them as swine influenza A (H1N1) viruses.
Nucleotide sequence analysis of the Haemagglutinin (HA) and
Neuraminidase (NA) are similar to each other and the majority of
their genes of swine influenza viruses, two genes coding for the
neuraminidase (NA) and matrix (M) proteins are similar to
corresponding genes of swine influenza. Sequence similarity between
the 2009 A (H1N1) virus and its nearest relatives indicates that its
gene segments have been circulating undetected for an extended
period. Nucleic acid sequence Maximum Likelihood (MCL) and
DNA Empirical base frequencies, Phylogenetic relationship amongst
the HA genes of H1N1 virus isolated in Genbank having high
nucleotide sequence homology.
In this paper we used 16 HA nucleotide sequences from NCBI for
computing sequence relationships similarity of swine influenza A
virus using the following method MCL the result is 28%, 36.64% for
Optimal tree with the sum of branch length, 35.62% for Interior
branch phylogeny Neighber – Join Tree, 1.85% for the overall
transition/transversion, and 8.28% for Overall mean distance.
Abstract: This paper presents an optimal design of poly-phase induction motor using Quadratic Interpolation based Particle Swarm Optimization (QI-PSO). The optimization algorithm considers the efficiency, starting torque and temperature rise as objective function (which are considered separately) and ten performance related items including harmonic current as constraints. The QI-PSO algorithm was implemented on a test motor and the results are compared with the Simulated Annealing (SA) technique, Standard Particle Swarm Optimization (SPSO), and normal design. Some benchmark problems are used for validating QI-PSO. From the test results QI-PSO gave better results and more suitable to motor-s design optimization. Cµ code is used for implementing entire algorithms.
Abstract: Nowadays wireless technology plays an important
role in public and personal communication. However, the growth of
wireless networking has confused the traditional boundaries between
trusted and untrusted networks. Wireless networks are subject to a
variety of threats and attacks at present. An attacker has the ability to
listen to all network traffic which becoming a potential intrusion.
Intrusion of any kind may lead to a chaotic condition. In addition,
improperly configured access points also contribute the risk to
wireless network. To overcome this issue, a security solution that
includes an intrusion detection and prevention system need to be
implemented. In this paper, first the security drawbacks of wireless
network will be analyzed then investigate the characteristics and also
the limitations on current wireless intrusion detection and prevention
system. Finally, the requirement of next wireless intrusion prevention
system will be identified including some key issues which should be
focused on in the future to overcomes those limitations.
Abstract: Optimization of extraction of phenolic compounds
from Avicennia marina using response surface methodology was
carried out during the present study. Five levels, three factors
rotatable design (CCRD) was utilized to examine the optimum
combination of extraction variables based on the TPC of Avicennia
marina leaves. The best combination of response function was 78.41
°C, drying temperature; 26.18°C; extraction temperature and 36.53
minutes of extraction time. However, the procedure can be promptly
extended to the study of several others pharmaceutical processes like
purification of bioactive substances, drying of extracts and
development of the pharmaceutical dosage forms for the benefit of
consumers.
Abstract: In this paper our aim is to explore the construction of schoolgirl femininities, drawing on the results of an ethnographic study conducted in a high school in Ankara, Turkey. In this case study which tries to explore the complexities of gender discourses, we were initially motivated by the questions that have been put forward by critical and feminist literature on education which emphasize the necessarily conflicting and partial nature of both reproduction and resistance and the importance of gendered power relations in the school context. Drawing on this paradigm our research tries to address to a more specific question: how are multiple schoolgirl femininities constructed within the context of gendered school culture, and especially in relation to hegemonic masculinity? Our study reveals that the general framework of multiple femininities is engendered by a tension between two inter-related positions. The first one is different strategies of accommodation and resistance to the gender-related problems of education. The second one is the school experience of girls which is conditioned by their differential position vis-à-vis the masculine resistance culture that is dominant in the school.
Abstract: Impinging jets are used in various industrial areas as a cooling and drying technique. The current research is concerned with the means of improving the heat transfer for configurations with a minimum distance of the nozzle to the impingement surface. The impingement heat transfer is described using numerical methods over a wide range of parameters for an array of planar jets. These parameters include varying jet flow speed, width of nozzle, distance of nozzle, angle of the jet flow, velocity and geometry of the impingement surface. Normal pressure and shear stress are computed as additional parameters. Using dimensionless characteristic numbers the parameters and the results are correlated to gain generalized equations. The results demonstrate the effect of the investigated parameters on the flow.
Abstract: Automatic reading of handwritten cheque is a computationally
complex process and it plays an important role in financial
risk management. Machine vision and learning provide a viable
solution to this problem. Research effort has mostly been focused
on recognizing diverse pitches of cheques and demand drafts with an
identical outline. However most of these methods employ templatematching
to localize the pitches and such schemes could potentially
fail when applied to different types of outline maintained by the
bank. In this paper, the so-called outline problem is resolved by
a cheque information tree (CIT), which generalizes the localizing
method to extract active-region-of-entities. In addition, the weight
based density plot (WBDP) is performed to isolate text entities and
read complete pitches. Recognition is based on texture features using
neural classifiers. Legal amount is subsequently recognized by both
texture and perceptual features. A post-processing phase is invoked
to detect the incorrect readings by Type-2 grammar using the Turing
machine. The performance of the proposed system was evaluated
using cheque and demand drafts of 22 different banks. The test data
consists of a collection of 1540 leafs obtained from 10 different
account holders from each bank. Results show that this approach
can easily be deployed without significant design amendments.
Abstract: Thermal load calculations have been performed for
multi-layered walls that are composed of three different parts; a
common (sand and cement) plaster, and two types of locally
produced soft and hard bricks. The masonry construction of these
layered walls was based on concrete-backed stone masonry made of
limestone bricks joined by mortar. These multilayered walls are
forming the outer walls of the building envelope of a typical Libyan
house. Based on the periodic seasonal weather conditions, within the
Libyan cost region during summer and winter, measured thermal
conductivity values were used to implement such seasonal variation
of heat flow and the temperature variations through the walls. The
experimental measured thermal conductivity values were obtained
using the Hot Disk technique. The estimation of the thermal
resistance of the wall layers ( R-values) is based on measurements
and calculations. The numerical calculations were done using a
simplified analytical model that considers two different wall
constructions which are characteristics of such houses. According to
the obtained results, the R-values were quite low and therefore,
several suggestions have been proposed to improve the thermal
loading performance that will lead to a reasonable human comfort
and reduce energy consumption.
Abstract: Analytical seismic response of multi-story building
supported on base isolation system is investigated under real
earthquake motion. The superstructure is idealized as a shear type
flexible building with lateral degree-of-freedom at each floor. The
force-deformation behaviour of the isolation system is modelled by
the bi-linear behaviour which can be effectively used to model all
isolation systems in practice. The governing equations of motion of
the isolated structural system are derived. The response of the system
is obtained numerically by step-by-method under three real recorded
earthquake motions and pulse motions associated in the near-fault
earthquake motion. The variation of the top floor acceleration, interstory
drift, base shear and bearing displacement of the isolated
building is studied under different initial stiffness of the bi-linear
isolation system. It was observed that the high initial stiffness of the
isolation system excites higher modes in base-isolated structure and
generate floor accelerations and story drift. Such behaviour of the
base-isolated building especially supported on sliding type of
isolation systems can be detrimental to sensitive equipment installed
in the building. On the other hand, the bearing displacement and base
shear found to reduce marginally with the increase of the initial
stiffness of the initial stiffness of the isolation system. Further, the
above behaviour of the base-isolated building was observed for
different parameters of the bearing (i.e. post-yield stiffness and
characteristic strength) and earthquake motions (i.e. real time history
as well as pulse type motion).
Abstract: The present energy situation and the concerns
about global warming has stimulated active research interest
in non-petroleum, carbon free compounds and non-polluting
fuels, particularly for transportation, power generation, and
agricultural sectors. Environmental concerns and limited
amount of petroleum fuels have caused interests in the
development of alternative fuels for internal combustion (IC)
engines. The petroleum crude reserves however, are declining
and consumption of transport fuels particularly in the
developing countries is increasing at high rates. Severe
shortage of liquid fuels derived from petroleum may be faced
in the second half of this century. Recently more and more
stringent environmental regulations being enacted in the USA
and Europe have led to the research and development
activities on clean alternative fuels. Among the gaseous fuels
hydrogen is considered to be one of the clean alternative fuel.
Hydrogen is an interesting candidate for future internal
combustion engine based power trains. In this experimental
investigation, the performance and combustion analysis were
carried out on a direct injection (DI) diesel engine using
hydrogen with diesel following the TMI(Time Manifold
Injection) technique at different injection timings of 10
degree,45 degree and 80 degree ATDC using an electronic
control unit (ECU) and injection durations were controlled.
Further, the tests have been carried out at a constant speed of
1500rpm at different load conditions and it can be observed
that brake thermal efficiency increases with increase in load
conditions with a maximum gain of 15% at full load
conditions during all injection strategies of hydrogen. It was
also observed that with the increase in hydrogen energy share
BSEC started reducing and it reduced to a maximum of 9% as
compared to baseline diesel at 10deg ATDC injection during
maximum injection proving the exceptional combustion
properties of hydrogen.
Abstract: To understand the material characteristics of singleand
poly-crystals of pure copper, the respective relationships between
crystallographic orientations and microstructures, and the bending
and mechanical properties were examined. And texture distribution
is also analyzed. A bending test is performed in a SEM apparatus and
while its behaviors are observed in situ. Furthermore, some
analytical results related to crystal direction maps, inverse pole
figures, and textures were obtained from EBSD analyses.
Abstract: Graduate attributes have received increasing attention
over recent years as universities incorporate these attributes into the
curriculum. Graduates who have adequate technical knowledge only
are not sufficiently equipped to compete effectively in the work
place; they also need non disciplinary skills ie, graduate attributes.
The purpose of this paper is to investigate the impact of an eportfolio
in a technical communication course to enhance engineering
students- graduate attributes: namely, learning of communication,
critical thinking and problem solving and teamwork skills. Two
questionnaires were used to elicit information from the students: one
on their preferred and the other on the actual learning process. In
addition, student perceptions of the use of eportfolio as a learning
tool were investigated. Preliminary findings showed that most of the
students- expectations have been met with their actual learning. This
indicated that eportfolio has the potential as a tool to enhance
students- graduate attributes.
Abstract: In this paper, we will present an architecture for the
implementation of a real time stereoscopic images correction's
approach. This architecture is parallel and makes use of several
memory blocs in which are memorized pre calculated data relating to
the cameras used for the acquisition of images. The use of reduced
images proves to be essential in the proposed approach; the
suggested architecture must so be able to carry out the real time
reduction of original images.
Abstract: A stage-structured predator-prey system with two time delays is considered. By analyzing the corresponding characteristic equation, the local stability of a positive equilibrium is investigated and the existence of Hopf bifurcations is established. Formulae are derived to determine the direction of bifurcations and the stability of bifurcating periodic solutions by using the normal form theory and center manifold theorem. Numerical simulations are carried out to illustrate the theoretical results. Based on the global Hopf bifurcation theorem for general functional differential equations, the global existence of periodic solutions is established.
Abstract: To solve the quick and accurate level-adjusting
problem in the process of spacecraft precise mating, automatic leveling
and equalizing hoist device for spacecraft is developed. Based on
lifting point adjustment by utilizing XY-workbench, the leveling and
equalizing controller by a self-adaptive control algorithm is proposed.
By simulation analysis and lifting test using engineering prototype,
validity and reliability of the hoist device is verified, which can meet
the precision mating requirements of practical applications for
spacecraft.
Abstract: The distressing flood scenarios that occur in
recent years at the surrounding areas of Sarawak River have
left damages of properties and indirectly caused disruptions of
productive activities. This study is meant to reconstruct a 100-year
flood event that took place in this river basin. Sarawak River Subbasin
was chosen and modeled using the one-dimensional
hydrodynamic modeling approach using InfoWorks River Simulation
(RS), in combination with Geographical Information System (GIS).
This produces the hydraulic response of the river and its floodplains
in extreme flooding conditions. With different parameters introduced
to the model, correlations of observed and simulated data are
between 79% – 87%. Using the best calibrated model, flood
mitigation structures are imposed along the sub-basin. Analysis is
done based on the model simulation results. Result shows that the
proposed retention ponds constructed along the sub-basin provide the
most efficient reduction of flood by 34.18%.
Abstract: The purpose of this research is to establish the experimental conditions for removal of Cibacron Brilliant Yellow 3G-P dye (CBY) from aqueous solutions by sorption onto coffee husks as a low-cost sorbent. The effects of various experimental parameters (e.g. initial CBY dye concentration, sorbent mass, pH, temperature) were examined and the optimal experimental conditions were determined. The results indicated that the removal of the dye was pH dependent and at initial pH of 2, the dye was removed effectively. The CBY dye sorption data were fitted to Langmuir, Freundlich, Temkin and Dubinin-Radushkevich equilibrium models. The maximum sorption capacity of CBY dye ions onto coffee husks increased from 24.04 to 35.04 mg g-1 when the temperature was increased from 293 to 313 K. The calculated sorption thermodynamic parameters including ΔG°, ΔH°, and ΔS° indicated that the CBY dye sorption onto coffee husks is a spontaneous, endothermic and mainly physical in nature.
Abstract: Many experimental results suggest that more precise spike timing is significant in neural information processing. We construct a self-organization model using the spatiotemporal pat-terns, where Spike-Timing Dependent Plasticity (STDP) tunes the conduction delays between neurons. We show that, for highly syn-chronized inputs, the fluctuation of conduction delays causes globally continuous and locally distributed firing patterns through the self-organization.