Abstract: The soil ecology of the organic and mineral soil layers
of laurel-leaved and Cryptomeria japonica forest in the Kasuga-yama
Hill Primeval Forest (Nara, Japan) was assessed. The number of
bacteria obtained by the dilution plate count method was less than
0.05% of those counted by the direct microscopic count. We therefore
found that forest soil contains large numbers of non-culturable
bacteria compared with agricultural soils. The numbers of bacteria and
fungi obtained by both the dilution plate count and the direct
microscopic count were larger in the deeper horizons (F and H) of the
organic layer than in the mineral soil layer. This suggests that active
microbial metabolism takes place in the organic layer. The numbers of
bacteria and the length of fungal hyphae obtained by the direct count
method were greater in the H horizon than in the F horizon. The direct
microscopic count revealed numerous non-culturable bacteria and
fungi in the soil. The ratio of fungal to bacterial biomass was lower in
the laurel-leaved forest soil. The fungal biomass was therefore
relatively low in the laurel-leaved forest soil due to differences in
forest vegetation.
Abstract: In elevating performance in competetive sports, an
athlete must continously train in achieving maximum
performance,but needs to pay attention to recovery therapy, that is to
recover from fatigue as well as injury.The correct recovery therapy
will assist in process of recovery and helps in the training in
achieving better performace. Binahong (Anredera cordifolia) was
proven empirically by the locals in assisting speedy recovery from an
injury.Clinical research with lab animals receiving blunt trauma
injury, microscopically shown signs of: 1) redness, 2) heatiness, 3)
swelling and, 4) lack of activity. There is also microscopic indication
of: 1) infiltration of inflame cells (migration of cells to the trauma
area), 2) Cells necrosis, 3) Congestion (as a result of dead red blood
cells), 4) uedema. On administration of Binahong for 3 days, there is
a significant drop of 5% in cell inflammation, 2% increase of
fibroblast (cell membrance) count.Conclutin: Binahong do assist in
reducing cell inflammation and increase counts of cells fibroblast.
Suggestion: In helping athlete's to recover from force injury, we need
study about Binahong's roots to inflammation cell and healing of
injuried cell.
Abstract: This paper presents a spectroscopic study on doping
of Vanadyl pathalocyanine (VOPc) by [6,6]-phenyl C61 butyric acid
methyl ester (PCBM). The films are characterized by UV/Vis/NIR
spectroscopy. A drastic increase in the absorption coefficient has
been observed with increasing dopant concentration. Optical
properties of VOPc:PCBM films deposited by spin coating technique
were studied in detail. Optical band gap decreased with the PCBM
incorporation in the VOPc film. Optical band gap calculated from the
absorption spectra decreased from 3.32 eV to 3.26 eV with a
variation of 0–75 % of PCBM concentration in the VOPC films.
Abstract: The present microfluidic study is emphasizing the flow behavior within a Y shape micro-bifurcation in two similar flow configurations. We report here a numerical and experimental investigation on the velocity profiles evolution and secondary flows, manifested at different Reynolds numbers (Re) and for two different boundary conditions. The experiments are performed using special designed setup based on optical microscopic devices. With this setup, direct visualizations and quantitative measurements of the path-lines are obtained. A Micro-PIV measurement system is used to obtain velocity profiles distributions in a spatial evolution in the main flows domains. The experimental data is compared with numerical simulations performed with commercial computational code FLUENT in a 3D geometry with the same dimensions as the experimental one. The numerical flow patterns are found to be in good agreement with the experimental manifestations.
Abstract: In this paper we present discretization and decomposition methods for a multi-component transport model of a chemical vapor deposition (CVD) process. CVD processes are used to manufacture deposition layers or bulk materials. In our transport model we simulate the deposition of thin layers. The microscopic model is based on the heavy particles, which are derived by approximately solving a linearized multicomponent Boltzmann equation. For the drift-process of the particles we propose diffusionreaction equations as well as for the effects of heat conduction. We concentrate on solving the diffusion-reaction equation with analytical and numerical methods. For the chemical processes, modelled with reaction equations, we propose decomposition methods and decouple the multi-component models to simpler systems of differential equations. In the numerical experiments we present the computational results of our proposed models.
Abstract: Temperature, relative humidity and overhygroscopic
moisture fields in a sandstone wall provided with interior thermal
insulation were calculated in order to assess the hygric performance
of the retrofitted wall. Computational simulations showed that during
the time period of 10 years which was subject of investigation no
overhygroscopic moisture appeared in the analyzed building
envelope so that it performed in a satisfactory way from the hygric
point of view.
Abstract: According to investigating impact of complexity of
stereoscopic frame pairs on stereoscopic video coding and
transmission, a new rate control algorithm is presented. The proposed
rate control algorithm is performed on three levels: stereoscopic group
of pictures (SGOP) level, stereoscopic frame (SFrame) level and
frame level. A temporal-spatial frame complexity model is firstly
established, in the bits allocation stage, the frame complexity, position
significance and reference property between the left and right frames
are taken into account. Meanwhile, the target buffer is set according to
the frame complexity. Experimental results show that the proposed
method can efficiently control the bitrates, and it outperforms the fixed
quantization parameter method from the rate distortion perspective,
and average PSNR gain between rate-distortion curves (BDPSNR) is
0.21dB.
Abstract: Automatic determination of blood in less bright or
noisy capsule endoscopic images is difficult due to low S/N ratio.
Especially it may not be accurate to analyze these images due to the
influence of external disturbance. Therefore, we proposed detection
methods that are not dependent only on color bands. In locating
bleeding regions, the identification of object outlines in the frame and
features of their local colors were taken into consideration. The results
showed that the capability of detecting bleeding was much improved.
Abstract: The zinc and iron environments in different growth
stages have been studied with EXAFS and XANES with Brookhaven
Synchrotron Light Source. Tissue samples included meat, organ,
vegetable, leaf, and yeast. The project studied the EXAFS and
XANES of tissue samples using Zn and Fe K-edges. Duck embryo
samples show that brain and intestine would contain shorter EXFAS
determined Zn-N/O bond; as with the cases of fresh yeast versus
reconstituted live yeast and green leaf versus yellow leaf. The
XANES Fourier transform characteristic-length would be useful as a
functionality index for selected types of tissue samples in various
physical states. The extension to the development of functional
synchrotron imaging for tissue engineering application based on
spectroscopic technique is discussed.
Abstract: A simple and dexterous in situ method was introduced to load CdS nanocrystals into organofunctionalized mesoporous, which used an ion-exchange method. The products were extensively characterized by combined spectroscopic methods. X- ray diffraction (XRD) and high-resolution transmission electron microscopy (HRTEM) demonstrated both the maintenance of pore symmetry (space group p6mm) of SBA-15 and the presence of CdS nanocrystals with uniform sizes of about 6 - 8 nm inside the functionalized SBA-15 channels. These mesoporous silica-supported CdS composites showed room temperature photoluminescence properties with a blue shift, indicating the quantum size effect of nanocrystalline CdS.
Abstract: Tea is consumed by a big part of the world-s
population. It has an enormous importance for the Turkish culture.
Nearly it is brewed every morning and evening at the all houses. Also it is consumed with lemon wedge. Habitual drinking of tea
infusions may significantly contribute to daily dietary requirements of elements.
Different instrumental techniques are used for determination of
these elements. But atomic and mass spectroscopic methods are preferred most. In these study chromium, iron and selenium contents
after the hot water brewing of black and green tea were determined
by Optical Emission Spectroscopy (ICP-OES). Furthermore, effect
of lemon addition on chromium, iron and selenium concentration tea
infusions is investigated.
Results of the investigation showed that concentration of
chromium, iron and selenium increased in black tea with lemon addition. On the other hand only selenium is increased with lemon
addition in green tea. And iron concentration is not detected in green
tea but its concentration is determined as 1.420 ppm after lemon addition.
Abstract: Analysis of the elastic scattering of protons on 6,7Li
nuclei has been done in the framework of the optical model at the
beam energies up to 50 MeV. Differential cross sections for the 6,7Li +
p scattering were measured over the proton laboratory–energy range
from 400 to 1050 keV. The elastic scattering of 6,7Li+p data at
different proton incident energies have been analyzed using singlefolding
model. In each case the real potential obtained from the
folding model was supplemented by a phenomenological imaginary
potential, and during the fitting process the real potential was
normalized and the imaginary potential optimized. Normalization
factor NR is calculated in the range between 0.70 and 0.84.
Abstract: A numerical method is developed for simulating
the motion of particles with arbitrary shapes in an effectively
infinite or bounded viscous flow. The particle translational and
angular motions are numerically investigated using a fluid-structure
interaction (FSI) method based on the Arbitrary-Lagrangian-Eulerian
(ALE) approach and the dynamic mesh method (smoothing and
remeshing) in FLUENT ( ANSYS Inc., USA). Also, the effects of
arbitrary shapes on the dynamics are studied using the FSI method
which could be applied to the motions and deformations of a single
blood cell and multiple blood cells, and the primary thrombogenesis
caused by platelet aggregation. It is expected that, combined with a
sophisticated large-scale computational technique, the simulation
method will be useful for understanding the overall properties of blood
flow from blood cellular level (microscopic) to the resulting
rheological properties of blood as a mass (macroscopic).
Abstract: This paper covered a series of key points in terms of 2D to 3D stereoscopic conversion. A successfully applied stereoscopic conversion approach in current visual effects industry was presented. The purpose of this paper is to cover a detailed workflow and concept, which has been successfully used in 3D stereoscopic conversion for feature films in visual effects industry, and therefore to clarify the process in stereoscopic conversion production and provide a clear idea for those entry-level artists to improve an overall understanding of 3D stereoscopic in digital compositing field as well as to the higher education factor of visual effects and hopefully inspire further collaboration and participants particularly between academia and industry.
Abstract: Identifying the nature of protein-nanoparticle
interactions and favored binding sites is an important issue in
functional characterization of biomolecules and their physiological
responses. Herein, interaction of silver nanoparticles with lysozyme
as a model protein has been monitored via fluorescence spectroscopy.
Formation of complex between the biomolecule and silver
nanoparticles (AgNPs) induced a steady state reduction in the
fluorescence intensity of protein at different concentrations of
nanoparticles. Tryptophan fluorescence quenching spectra suggested
that silver nanoparticles act as a foreign quencher, approaching the
protein via this residue. Analysis of the Stern-Volmer plot showed
quenching constant of 3.73 μM−1. Moreover, a single binding site in
lysozyme is suggested to play role during interaction with AgNPs,
having low affinity of binding compared to gold nanoparticles.
Unfolding studies of lysozyme showed that complex of lysozyme-
AgNPs has not undergone structural perturbations compared to the
bare protein. Results of this effort will pave the way for utilization of
sensitive spectroscopic techniques for rational design of
nanobiomaterials in biomedical applications.
Abstract: There are lots of different ways to find the natural
frequencies of a rotating system. One of the most effective methods
which is used because of its precision and correctness is the
application of the transfer matrix. By use of this method the entire
continuous system is subdivided and the corresponding differential
equation can be stated in matrix form. So to analyze shaft that is this
paper issue the rotor is divided as several elements along the shaft
which each one has its own mass and moment of inertia, which this
work would create possibility of defining the named matrix. By
Choosing more elements number, the size of matrix would become
larger and as a result more accurate answers would be earned. In this
paper the dynamics of a rotor-bearing system is analyzed,
considering the gyroscopic effect. To increase the accuracy of
modeling the thickness of the disk and bearings is also taken into
account which would cause more complicated matrix to be solved.
Entering these parameters to our modeling would change the results
completely that these differences are shown in the results. As said
upper, to define transfer matrix to reach the natural frequencies of
probed system, introducing some elements would be one of the
requirements. For the boundary condition of these elements, bearings
at the end of the shaft are modeled as equivalent spring and dampers
for the discretized system. Also, continuous model is used for the
shaft in the system. By above considerations and using transfer
matrix, exact results are taken from the calculations. Results Show
that, by increasing thickness of the bearing the amplitude of vibration
would decrease, but obviously the stiffness of the shaft and the
natural frequencies of the system would accompany growth.
Consequently it is easily understood that ignoring the influences of
bearing and disk thicknesses would results not real answers.
Abstract: Image mosaicing is a technique that permits to enlarge the field of view of a camera. For instance, it is employed to achieve panoramas with common cameras or even in scientific applications, to achieve the image of a whole culture in microscopical imaging. Usually, a mosaic of cell cultures is achieved through using automated microscopes. However, this is often performed in batch, through CPU intensive minimization algorithms. In addition, live stem cells are studied in phase contrast, showing a low contrast that cannot be improved further. We present a method to study the flat field from live stem cells images even in case of 100% confluence, this permitting to build accurate mosaics on-line using high performance algorithms.
Abstract: Titanium gels doped with water-soluble cationic porphyrin were synthesized by the sol–gel polymerization of Ti (OC4H9)4. In this work we investigate the spectroscopic properties along with SEM images of tetra carboxyl phenyl porphyrin when incorporated into porous matrix produced by the sol–gel technique.
Abstract: A four element prototype phased array surface probe
has been designed and constructed to improve clinical human
prostate spectroscopic data. The probe consists of two pairs of
adjacent rectangular coils with an optimum overlap to reduce the
mutual inductance. The two pairs are positioned on the anterior and
the posterior pelvic region and two couples of varactors at the input
of each coil undertake the procedures of tuning and matching. The
probe switches off and on automatically during the consecutive
phases of the MR experiment with the use of an analog switch that is
triggered by a microcontroller. Experimental tests that were carried
out resulted in high levels of tuning accuracy. Also, the switching
mechanism functions properly for various applied loads and pulse
sequence characteristics, producing only 10 μs of latency.
Abstract: Zinc borates can be used as multi-functional
synergistic additives with flame retardant additives in polymers. Zinc
borate is white, non-hygroscopic and powder type product. The most
important properties are low solubility in water and high dehydration
temperature. Zinc borates dehydrate above 290°C and anhydrous zinc
borate has thermal resistance about 400°C. Zinc borates can be
synthesized using several methods such as hydrothermal and solidstate
processes. In this study, the solid-state method was applied at
low temperatures of 600oC and 700oC using the starting materials of
ZnO and H3BO3 with several mole ratios. The reaction time was
determined as 4 hours after some preliminary experiments. After the
synthesis, the crystal structure and the morphology of the products
were examined by X-Ray Diffraction (XRD) and Fourier Transform
Infrared Spectroscopy (FT-IR). As a result the forms of ZnB4O7,
Zn3(BO3)2, ZnB2O4 were synthesized and obtained along with the
unreacted ZnO.